Search Documents

The most critical step in the development of any mining project is the completion of a feasibility study. The feasibility study has one primary goal; to demonstrate that the project is economically viable if it is designed, constructed and operated in accordance with the concepts set forth in the study. Starting from a mineral resource data base, the feasibility study will define the ore reserves, the mining methods, the mineral processing concepts and the scale of the project. The disciplined activity of developing a feasibility study leads the proponent to examine every aspect of the project, many of which might otherwise be ignored. All technical concepts will be established and the corporate philosophy with respect to organisational structure, social and environmental responsibility, infrastructure contributions and financing will be determined. All the major decisions about how the project will be developed are made during the feasibility study. The success of the project will then depend upon the assumptions and decisions in the feasibility study and the ability and empowerment of the development team.

Jan 1, 1997

By Doig ID, Phillips HR

As a prelude to studying the sorption desorption and permeability behaviour of coal cores in a triaxial stressing rig using sorb- able gases, the air permeability of typical cores was measured. Lump coal samples were obtained from three gas-troubled collieries in Queensland and New South Wales. These were cored in the laboratory and a simple laboratory permeameter employed which accepted 38 x 40 mm cores in a thick rubber sheath. Air pressure of 500 kPa was applied outside the sheath to provide suitable sealing between the rubber and the coal. Differential driving pressures up to 100 kPa were employed and the air flow measured by displacement of water columns in inverted graduated cylinders. Flow measurements accurate to + 2% could thereby be achieved. Coal lumps were cored both parallel and perpen- dicular to the bedding plane, and were observed prior to measurement for any notable features, in particular for the presence of fissures. Between samples an overall variation of from 100 milliDarcy was found in Appin, Westcliff and Leichhardt coals. Significant variation was observed both from section to section of a core and between regions of a

Jan 1, 1982

By Fewings JH

When the mining and milling of 1100 Copper Orebody commenced, difficulties were experienced in producing a satisfactory grade of copper concentrate. The major concentrate contaminants were fine pyrite and silica, particularly in the minus 10 microns fraction. Studies of the 1100 Orebody showed that much of the fine grained pyrite and a proportion of the silica present in the ore contained carbonaceous matter in the form of complete or partial rims and as internal carbon films disseminated throughout grains. The hydrophobic surface property of the carbonaceous material resulted in an inherently flotable fine pyrite and silica fraction. The addition of a 60:40 mixture of nigrosine and dextrine, initially to a prefloat concentrate of the inherently flotable carbonaceous material and finally to'the total copper flotation feed, successfully controlled the flotation rates of the carbonaceous pyrite and silica. The objective of a 25 per cent Cu concentrate grade was then achieved without decreasing copper recovery.

Jan 1, 1970

Two examples of risk assessment and risk management in action are discussed. The first is in a management context in relation to Kingsgate Consolidated LtdÆs Chatree operation in Thailand. Kingsgate has conducted an over-riding risk management program to assess and manage risk across its complete business from the Sydney and Bangkok offices through to the Chatree Mine and the companyÆs exploration group. This example addresses how Kingsgate has applied risk management, particularly to the process operation, and the benefits that have been gained. The second is in an operational context in relation to Minara Resources LtdÆs Murrin Murrin operation in Western Australia. The subject is the methodology and outcomes of a risk assessment across the Murrin Murrin operation specifically to identify and assess risks with potential impacts from $1 M to $7 M. This section of the paper then shows how the outcomes of the risk assessment were integrated into MinaraÆs strategic plan to debottleneck the plant and increase nickel production.

Jan 1, 2004

By J B. Holman, P A. Weber, P Lindsay

Underground and opencast coal mining has occurred since 1896 on the Stockton Plateau, West Coast, New Zealand. Acid Rock Drainage (ARD) from historic and current mine workings has had an adverse environmental impact on the surrounding aquatic environment. The two main catchments affected by ARD from historic and current mine workings are the Mangatini and St Patrick Stream catchments. Solid Energy New Zealand Ltd (SENZ) is using active (e.g. alkali dosing) and passive (e.g. engineered cover) technologies to mitigate the adverse environmental effects associated with ARD contaminated waterways. This paper discusses the passive technologies. Principal strategies include the capping of high capacity potentially acid-forming volumes of overburden. The mudstones were found to generally have the highest sulphur levels compared to other overburden lithologies. Areas with high mudstone volumes are prioritised to be encapsulated and 390 Ha is planned to be capped in the Mangatini catchment in the near future.   Monitoring beneath granite, cement kiln dust and coal combustion product covers show oxygen can be reduced to less than 10% of atmospheric levels. Laboratory column leach tests that were subjected to oxygen flux rates of 10 % showed reducing oxygen ingress into acid-forming material can result in significant acid load reductions.   The oxygen content below the cement kiln dust cover was generally lower than 5% and water quality measured in lysimeters beneath this cover improved after 50 weeks of emplacement. Column leach tests containing saturated samples were undertaken to determine the most appropriate water medium in preventing pyrite oxidation. The sample saturated with ARD (pH ~ 3) had a negligible acid production rate and leached very minor Al concentrations although Al is soluble at low pH. This indicated saturating waste rock dumps with ARD can be an effective method in mitigating ARD formation.

Jan 1, 2007

By Davey KJ

Complex sulphide ores are characterised by complex texture of the valuable minerals. Any assessment of the performance of differential flotation circuits treating such ore should include analysis of the effects of poor liberation of the valuable minerals. Selected samples were taken from balanced size by size surveys of the flotation section of a concentrator treating an ore body containing fine grained galena and sphalerite in a matrix of iron sulphides which is mostly pyrite. liberation measurements were made using the QEM*SEM system on four or seven size fractions. The measurements indicated that less than 40 per cent of the galena and less than 60 per cent of the sphalerite in the flotation feed was liberated. The final concentrates were largely composed of composites of valuable minerals and iron sulphide however there was a small but significant fraction of liberated iron sulphide. Using the sized mineral flows obtained from the original balances and the liberation measurements, a satisfactory liberation balance was obtained. This enabled the effect of liberation on the flotation performance to be examined; not only for the entire circuit but also in the rougher, scavenger and cleaning sections. In the zinc circuit the effect of a regrind mill could be assessed. Recovery of galena in the lead circuit was limited by the recovery of composite lead particles. Recovery of liberated galena exceeded 95 per cent in all size fractions while the recovery of composite galena exceeded 85 per cent below 38 ¦m but fell sharply above 38 ¦m. Examination of the behaviour of the liberated and composite galena in the various sections of the lead flotation circuit revealed high recoveries of both liberated and composite galena particles in the roughing and scavenging sections but very low recoveries in the final two cleaning stages. Similar trends to those observed in the lead circuit applied in the zinc circuit although the performance of the liberated sphalerite also fell off at sizes greater than 38 pm in this case. Thus the zinc recovery was limited by the flotation of both the liberated and the composite sphalerite. The effect of regrinding was to increase the recovery of sphalerite mainly by reducing the amounts of sphalerite in less liberated sizes rather than by increasing the liberation of the sphalerite within a given size Fraction.

Jan 1, 1993

By Sterns UJ, Weller KR

Grinding to sizes less than 80 per cent passing 20 ¦m in both primary and regrind circuits is becoming increasingly important in processing metalliferous ores, as many of the remaining orebodies are very fine-grained and refractory. The process of very fine grinding, however, is expensive, and neither the performance nor the design criteria are well understood. This paper presents some findings from a collaborative research program, one of the objectives of which has been to better understand and improve the performance of very fine grinding circuits. Data from surveys of an industrial tower mill grinding circuit are reviewed and analysed using the population balance models of the CS]RO and 7KMRC. The performance of both models with regard to changes in feed size distribution, ball load and feedrate is assessed using these data. From comparisons between pilot and full scale tower mill operation a prototype scaling methodology is also presented which shows promise in allowing the models to be used to predict the effect of changes in mill Design.

Jan 1, 1993

By Fourney W. L, Dick R. D

A small-charge rapid excavation system employing a novel penetrating cone fracture initiation and propagation technique has been demonstrated to be capable of excavating the hardest of rocks at efficiencies (energy per unit volume of rock removed) four to ten times greater than attainable with conventional drill and blast. Significant enhancements to the concept developed during the research efforts include the use of propellant rather than explosive charges and a device for containing the charges and effectively sealing the shot-holes. The experimental results, including the excavation of several tons of hard rock in a research mine, have confirmed the novel breakage process and provided a data base for the design of a continuous hard rock mining machine based upon the concept. The small-charge excavation system would be attractive for civil construc-tion operations where sensitive structures, equipment and personnel would be in close proximity to the excavation face. The system would be attractive for selective mining operations where the ore rock could be fragment-ed and processed separately from the barren country rock. The barren rock could then be backfilled underground and eliminated from the traditional hauling and milling operations.

Jan 1, 1990

By Daxian Z, Youdi Z, Shucai Y

The Huolinhe surface mine is a very large-scale surface coal mine, located in the north-east area of China with a production rate of 1.2 Mtpa. Its coal haulage system has a large capacity, long transportation line and high degree of automation. The system comprises two crushing plants, many belt conveyors, four surge bunkers, one loading bunker, one coal storage and five end product bunkers. In this paper, the network patterns of semi-continuous systems in surface mines are studied, the reliability calculation methods and a simulation model are established and the software for computing the reliability of a semi-continuous system is worked out. By considering the whole coal haulage system in the Huolinhe surface mine, the authors developed the system reliability-numerical simulation method. The steps and the computing results of this method are described in detail. Through the calculation, we can master the present situation of system reliability and the main factors impairing system reliability, expose the system weak links, put forward the ways of enhancing system reliability and furnish the basis for improving the system and equipment. The way of increasing capacity and methods of enhancing system reliability are further raised.

Jan 1, 1995

By M Fisher, P Bradley, D Rogers

New England Antimony Mines has operated the Hillgrove Gold Plant at Hillgrove in New South Wales since 1969, producing stibnite and arsenopyrite products by selective flotation. Gold is present in the ore as fine free gold, gold associated with stibnite and gold associated with arsenopyrite, with some ten to 20 per cent of the gold reporting to the antimony stream and 35 - 50 per cent reporting to the arsenopyrite stream. Opportunity to process the arsenopyrite concentrate for onsite recovery of the gold values to improve upon the ten per cent recovery achieved by conventional cyanidation was recognised and subject to comparison with biological oxidation, roasting, nitric acid oxidation, low temperature oxidation (Activox«) and conventional pressure oxidation. Following further testwork and a feasibility study, a 7500 tonnes per annum concentrate feed pressure oxidation autoclave circuit was constructed at Hillgrove and commissioned in October 1999. The plant has operated at the close to design capacity since commissioning whilst optimising various operational and metallurgical aspects. The last three years has seen the process achieve an overall gold recovery of greater than 90 per cent for oxidised concentrates.

Jan 1, 2002

By S Tavelli

This discussion will present a case study in developing solutions to a metropolitan quarryÆs public relations, legal, environmental, and productivity problems. It details an extensive and detailed project to address the blasting practice in a medium sized quarry that is surrounded by residential and industrial zones. The principle work was done over four months duration during the normal production season. It included detailed drilling and blasting audits for baseline information. In addition, geologic characterisation, seismic modeling, correction of deviations from best practices, and implementation and monitoring of precise electronic timing to provide dramatic solutions for the quarry. The quarry is in the near suburbs of a large metropolitan city. It is framed on two sides by residential municipalities and on two sides by industrial zones. At the start of the project, the quarry was in court as a result of the lawsuit by one of the neighboring towns that was suing to close the quarry. The lawsuit had progressed to the advanced stage where in the Judge had appointed an arbitrator to make the decision of continued operation. This arbitrator was to observe our progress and recommend to the Judge the disposition of the case.

Jan 1, 2004

Zinc produced by pyrometallurgical processing techniques suffers the disadvantage of restricted market potential because of its impurity contents, typically lead and cadmium. Market zinc to the Special High Grade (SHG) standard can only be produced by reflux distillation refining, which is costly in terms of energy and equipment, and potentially capacity limiting. Recent published laboratory work suggested that molten salt electrorefining of zinc metal is a potentially much cheaper alternative to the reflux distillation refining. The extrapolation of the laboratory results to an industrial configuration, however, resulted in an estimated power consumption for electrorefining and associated costs offering no advantage over current reflux distillation practice. A review of this estimate now shows that a serious error in calculation was made, and that the energy consumption for the electrorefining of molten zinc would be an order of magnitude lower than that for reflux distillation refining. While this is a promising indication, further research is required before development towards an industrial scale operation is warranted. This would particularly relate to the extent to which adverse electrolyte deterioration may take place and its potential effect on the anode and cathode efficiencies of the process. This paper considers the laboratory investigations required to explore the industrial potential of the molten salt electrorefining of zinc and foreshadows some of the practical problems to be solved in further development.

Jan 1, 2000

A small-charge rock excavation method based upon the Penetrating Cone Fracture (PCF) technique has been demonstrated to be capable of excavating the hardest of rocks. The PCF technique involves drilling shallow holes in the rock which are then pressurised at the bottom by a propellant charge device. A controlled fracture is initiated at the hole bottom comer and propagates in such a manner as to excavate the rock at an energy efficiency three to five times better than explosives. Due to the low flyrock velocities and airblast pressures realised with PCF breakage, the method may be used in close proximity to equipment and personnel and is thus ideally suited for integration into continuous hard rock excavation systems. Over the past 18 months full-scale testing of the PCF method has been carried out in mines in the US and Australia. This testing has utilised a 76 mm diameter gas injector for hole pressurisation and employed propellant charges ranging from 80 to 320 gm. In addition to extensive data on rock excavation performance, data on ground motion, dust, carbon monoxide and air blast have been obtained. These data indicate that none of the parameters associated with PCF breakage are detrimental to the development of PCF-based, continuous-excavation machines. Machines employing the PCF method may range from simple single-boom machines for secondary breakage and small precision-blasting jobs to integrated systems with several booms, continuous mucking capabilities and ground-support equipment for drifting and tunnelling.

Jan 1, 1993

By A Ruotsalainen

Mining industry sees a comprehensive future in optimisation and process control. High resource utilisation is a starting platform when lower operational costs with higher rate of return are the target. Simulation is quickly penetrating the mining industry as a planning tool. A discrete event simulation helps to visualise the reality of a mine and the various mining processes, which typically include a fair degree of complexity. What-if scenarios can help to determine the impact of occurring changes to production. Understanding of critical points in the layout and resource allocation at an early stage can help to optimise the material flow. The obtained information may then be used as proposal or confirmation of the system applicability and economy. Simulation is a way to fine-tune and optimise the resources within. It helps to predict system sensitivity to various aspects. Although simulation today is used typically in a feasibility stage, there is an opportunity to continue using simulation for further process enhancement. In the future simulation will without doubt be used increasingly as a dynamic simulation and continuous improvement tool. This paper discusses the use of OptimineÖ simulation tool in resource optimisation. Some examples describe the way the tool operates and how it helps to view the technology, mine layout and operational data.

Jan 1, 2003

By G Chitombo, G Lewis

The knowledge of the expected run of mine (ROM) fragmentation during the feasibility study of a green field site is essential for the design of downstream crushing and milling processes. However,the prediction of blast fragmentation can be a challenging process due to the uncertainty related to the blast design and rock mass parameters. In general,a number of possible blast designs are considered in a feasibility study,with factors such as bench height and blasthole diameter influencing the design. Rock mass parameters are normally derived from a limited number of geotechnical diamond drill cores. Although diamond drill core can provide detailed information concerning intact rock strength (unconfined compressive strength and point load),it provides limited structural information to predict the in situ block size distribution of the rock mass. The in situ block size is an essential input to the prediction of the fragmentation distribution, in particular the coarse end. This paper outlines the methodology of blast fragmentation modeling undertaken for a green field feasibility study at the Riska gold deposit in Indonesia. The favoured milling process for the feasibility study was dump leaching,with no crushing of the ore material extracted from the pit. For this reason,blast fragmentation was a critical issue to be addressed by the study. A range of blast designs were considered with bench heights and blasthole diameters ranging from 4 m to 7 m and 76 mm to 102 mm respectively. Rock mass data was obtained from 19 diamond drill cores across the deposit (total drill length approximately 2200 m). Intact rock strength was estimated from qualitative strength descriptors,while the in situ block size distribution of the rock mass was estimated from the Rock Quality Designation (RQD) of the core. The methodology of fragmentation prediction involved a number of steps including the estimation of rock mass parameters from diamond drillhole data including the estimation of the in situ block size, delineation of blast domains within the deposit,and the assessment of the impact of various blast design parameters and rock mass variation on the predicted fragmentation distribution. The modelling process for the Riska green field site highlighted the need for additional rock mass data to be collected post feasibility stage and once the development of the mine commenced.

Jan 1, 2004

The Olympic Dam Project constitutes a major resource of Copper and Uranium and has been under intensive evaluation since the discovery in 1975.A 500 metre deep rectangular shaft has been sunk into the deposit and this has been followed by 8400 metres of level, incline and decline development. 5 surface ventilation raises have also been constructed.Large scale trackless equipment is used to carry out the development, and productivity statistics are given.The paper describes the functionalised system used in the development program and discusses the maintenance support, and services required to carry out these works.The objectives of the Exploration Development program and the satisfactory results obtained from this work are also discussed.

Jan 1, 1985

By Eaton R. A

The design of most underground mining machines shows little evidence of regard for ergonomic principles and operator comfort. Likewise, efficiency and ease of operation often appear to have been given little consideration in machines where ruggedness and simplicity have tended to dictate the configuration. Improvements in productivity are amongst the benefits to be gained by a different approach to machine design. The paper describes the philosophy and features of a test bed Load-Haul-Dump Vehicle undergoing trials at Mount Isa Mines. This machine is the outcome of a Research and Development Programme conducted by the Department of Mechanical Engineering at the University of Queensland and Mount Isa Mines Limited. The diesel powered test bed features an enclosed, air conditioned cabin, with a suspended operator's control station and electrically operated controls. An electronically controlled hydrostatic transmission incorporating wheel slip control, is another innovation. The performance and operator acceptance of the machine has led to adoption of most of the concepts in a new machine now being put into production.

Jan 1, 1987

This paper presents results of the experiments carried out in Beth Energy No. 33 Mine for the purpose of alleviating problems associated with cutter roof. Cutter roof problems have delayed the advance of the entry development considerably and maintenance cost of these entries was very high due to the requirement of very extensive and heavy artificial supports. The study includes assessment of the problem, investigation of the geology and lithology of the mines, study of in-situ stresses and corrective measures to combat the problem. Two approaches were selected as the corrective measures: 1) implementing yield pillar concept in order to reduce the effects of in-situ horizontal stresses, 2) designing an effective roof reinforcement system and application procedure. Results of this study revealed that roof strata is weak and in-situ stresses are very high at the problem area which results in development of cutter roof. Implementation of yield pillar concept was found to be ineffective because cutter roof often developed at the entry face concurrent to the development. However, proper design and implementation of roof reinforcement system stabilized the roof and eliminated roof caving during both entry development and retreat of longwall face, despite existence of the cutter roof, at a much lower cost.

Jan 1, 1992

By L S. Barbour, M K. Meiers

Soil covers for mine waste are subject to changes in structure as a result of root development, and wet/dry or freeze/thaw cycling. The purpose of this study was to evaluate the changes in the hydraulic conductivity of three non-compacted clay covers over time. The covers are located on a sodic/saline overburden fill (30-Dump) at the Syncrude oilsands mine in Fort MacMurray, Alberta, Canada. Monitoring of these covers for temperature, matric suction, and water content by the University of Saskatchewan has been ongoing for more than three years. The three covers (D1, D2, and D3) were constructed in 1999 and are 50 cm, 35 cm, and 100 cm thick. The covers are comprised of a surface layer of reclaimed peat/mineral mix over a secondary reclaimed mineral soil (glacial till or glaciolacustrine clay), placed over a sloping shale surface. Field measurements of hydraulic conductivity within the secondary layer were obtained using a Guelph Permeameter during the 2000, 2001, and 2002 summer field seasons. Repeated measurements were made within the D1, D2, and D3 covers at depths of approximately 40 cm, 30 cm, and 60 cm, respectively. The values of hydraulic conductivity for the covers were similar to each other during each of the field study seasons. The mean hydraulic conductivity of the secondary layer increased every year: 2.5 + 10-6 cm/sec to 2.1 + 10-4 cm/sec to 4.3 + 10-4 cm/sec from 2000 to 2001 to 2002. Soil temperature data shows that one freeze/thaw cycle occurred each year at the measurement depths.

Jan 1, 2003

By J B. Farrow

The AJ Parker Cooperative Research Centre for Hydrometallurgy carries out research on behalf of, and in collaboration with, the Australian mining industry. As might be expected, much of its research is directed towards improving the efficiency of alumina and gold processing plants. However, the Centre also carries out research of relevance to base and other metal producers. A key element in its work is the successful transfer of its technology to the companies with which it is working. In general, this is achieved in the following five steps:definition of the problem through discussions with the company commissioning the research; execution of the research; assessment of the research findings; testing of the research findings by pilot plant or on-site trials; and implementation of the results on the full-scale. This pattern is exemplified by the work carried out by the Centre to improve the performance of gravity thickeners which are used throughout the minerals industry for solid-liquid separation. The research has focussed mainly on ways to optimise the use of flocculants (long chain polymers) to enhance thickener performance. It has been shown that the way the flocculant is mixed with the slurry is of profound importance. Computational fluid dynamics modelling of the feedwell region of thickeners and laboratory and plant flocculation studies have been used to determine better ways to contact the flocculant with the feed slurry. Implementation of these and other findings on the full-scale confirmed that improvements in thickener performance were indeed possible. As a result of this AMIRA funded thickener technology work, there have been considerable savings to a number of Australian mineral processing companies, through improved operation, higher throughputs and flocculant savings.

Jan 1, 2000