Search Documents

By B. D. Thompson

Many mines adopt necessarily conservative backfilling strategies due to a lack of understanding of their backfill behaviour. In the past five years, extensive instrumentation campaigns have focused on measuring in-situ cemented paste backfill behaviour. These tests have resulted in optimised backfilling efficiency through elimination or reduction of cure periods where; i) controls on backfill behaviour are understood, and ii) barricade pressures are demonstrated to be within a safe range using routine monitoring as a required QA/QC procedure. Recently, this work has been extended to consider hydraulic backfill operations. Two stopes have been instrumented at Vale?s Coleman and Garson Ramp mines. The instrumentation and deployment methods are discussed, and representative total earth pressure, pore pressure, and temperature data are presented. In one case, pressures in the stope are relatively low as drainage causes strength gain in the fill and so pressures are arched. In a second example, again, drainage causes strength gain in the fill, but increasing temperatures correlate with pressure increases even during downtimes in filling. These pressure increases are thought to be caused by thermal expansion of the backfill in confined locations. Generally, the instrumentation approach has proven successful in measuring hydraulic backfill behaviour and offers good potential for incorporation into a procedure to safely maximise backfilling efficiency through routine barricade pressure monitoring, when combined with safeguards to ensure adequate fill drainage.

Aug 1, 2013

By Tapio Leskinen

"l. IntroductionA reliable sampling system is the basis for an on-stream analyzer. This was realized in Outokumpu company when the development work of the Courier 300 On-Stream X-ray analysis system was started. Because Outokumpu Oy is a mining and mineral processing company, its engineers have been able to thoroughly test sampler prototypes in actual operating situations. The sampler development has been going for several years in close co-operation between company's concentrators, the Institute of Physics and the Instrument Division of Outokumpu Oy. The most active part of the work was done between 1969- 1972. Besides the reliable operation of a sampler special attention was paid to the representatively of the samples taken by the samplers. 2. The Courier 300 Sampling SystemThe sampling system comprises up to fourteen sampling circuits in one Courier analysis system. Each circuit consists of the following components:1. Primary sampler 2. Secondary sampler 3. Cleaner screen 4. Feeding tank5. Sample cell6. Timer-controlled sampler7. Pumps, sumps and pipesSecondary samplers, cleaner screen and feeding tanks are included in the secondary sct1npling system. The sample cells are located in the spectrometer cabinet of the analyzer."

Jan 1, 1976

Safe underground mine backfilling with hydraulic fill requires efficient fill drainage and stable fill retaining walls or bulkheads. If any or both the above two requirements are not satisfied, such a backfilling operation creates unsafe conditions and may lead to backfill retaining wall failures. Mine backfill retaining wall failures are always associated with economic losses, fatalities and interruption to mine production. Mining industry wants to either reduce or eliminate these fill retaining wall failures. The fill retaining wall failures could be effectively avoided through the use of fibre reinforced shotcrete fill retaining walls and engineered drainage systems through the retaining walls. This paper presents the experience of the author in developing, implementing, and monitoring several hundred fibre reinforced shotcrete fill retaining walls at a mine in Australia with the highest safety standard. The details on the mine backfill drainage system and fibre reinforced shotcrete fill retaining wall designs are also presented.

May 1, 2007

By O. Mejia, J. Drozdiak

"This paper summarizes a comprehensive energy and cost study comparing an existing SAG mill based circuit at Huckleberry Mine with two proposed circuits involving comminution technologies which are associated with energy efficiency: high pressure grinding rolls (HPGR) and high speed stirred mills. The specific energy requirements expressed as kWh/t for the proposed circuits were determined from pilotscale HPGR and stirred mill testing conducted at the University of British Columbia. Samples and operating data were collected from Huckleberry’s copper-molybdenum concentrator to evaluate current mill performance for comparison. To support the base case, the SABC circuit was modeled using JK SimMet® software. The main comparison focused on the complete energy requirements for each circuit, including materials handling equipment such as conveyors, screens, feeders and pumps. This paper also provides capital and operating cost estimates for each of the comminution circuits. The results showed that the HPGR - ball mill circuit achieved a 21% reduction in energy consumption over the existing SAG - ball mill circuit at the same P80 grind size of 160 µm. At a grind of 80% passing 75 µm, the HPGR - stirred mill circuit showed a 34% reduction in energy compared to the base case. It was concluded that the energy reduction for the new flowsheets significantly improved the economics of the Huckleberry comminution duty.INTRODUCTIONUp until now, tumbling mills such as AG/SAG mills and ball mills have had a dominant bearing on the design and economics of comminution circuits. However, it is commonly agreed that the majority of employed comminution processes are energy intensive and energy inefficient, accounting for up to 80% of overall process plant energy consumption and having an efficiency of as low as 1% (Abouzeid and Fuerstenau, 2009; Fuerstenau and Abouzeid, 2002). The U.S. department of energy reported that there is a potential to reduce energy consumption in the metals industry by up to 61% from current practice to bestestimated practical minimum energy consumption; suggestions included the implementation of best practices and the adoption of energy efficient mining and mineral processing technologies such as advanced blasting techniques, high pressure grinding rolls (HPGR) and stirred mills (U.S. DOE, 2007)."

Jan 1, 2013

By D Reddy Chinnasane

Outline Location of BirchtreeMine and Layout of 124 OB Cut and Fill Mining Background Purpose of the Studies Methodology Results and Analysis Conclusions and Recommendations

Oct 1, 2010

By P. C. McLeod

THE GECO OREBODY, located north of lake Superior in the Thunder Bay district of northern' Ontario, was discovered in 1953. Diamond drilling in the following year indicated a 15,000,000-ton ore-body, and production plans were made for the shipment of copper and zinc concentrates in three years. To accomplish this, the Geco Project was initiated. The property was in an undevdoped, inaccessible area, and the project involved the conversion and extension of a logging road to the property, the construction of two railways and seventy miles of hydro transmission line, the erection of a municipality, the building of a plant, and the development of an underground mine to produce 3,300 tons per day. This paper describes some of the methods used in the underground development phase of the Geco Project.

Jan 1, 1958

By H. J. McQueen

The irregular history of Mg wrought products is briefly described. The temperature and strain rate dependence of microstructural evolution, flow stress and ductility of Mg alloys in hot working, are described. The flow curves rose rapidly to a peak stress which was lower as temperature T rose and strain rate e declined and above 300°C the curves extended into plateaus until failure. Clearly grains not oriented for slip undergo mechanical twinning in the initial stages (a 0.15) at all temperatures. Basal slip proceeds in suitable grains and in the twins. The stress concentrations at grain and twin boundaries lead to slip on non-basal systems and to the formation of subgrains with greater dynamic recovery (DRV) at higher T or lower e. With increasing strain, misorientation builds up resulting in dynamic recrystallization (DRX) first at twin intersections and later at grain boundaries which have become quite serrated. Even after extensive straining at high temperatures, the new grains are found mainly along the boundaries of the original grains, leaving their centers with only basal slip except when nucleation at twins leads to completion of DRX throughout a grain. Despite similar shear modulus and melting point to Al, hot mechanical forming behavior of Mg alloys differ due to differences in crystal slip systems, twinning, and second phases. Moreover, the influences on forming of alloy additions (solutes, segregation in casting, dispersoids, precipitation) and impurities are not as well catalogued as for Al. Despite the benefits from dynamic recrystallization, varied grain orientation effects, heterogeneous substructures and the resulting stress concentrations result in considerably lower ductility for Mg alloys at the same stress level as for Al materials. Application of these theories to extrusion, rolling and forging and the effects on product properties are surveyed.

Jan 1, 2006

By O. M. Arafat, J. A. Finch

"The Functional Performance Equation calculated from a plant grinding survey defines two distinct ball mill circuit efficiencies and how they relate to total production rate through the target grind size. The survey data are also used to calculate a complete ball mill size distribution model, represented by the energy specific grinding rates, not just through the target grind size, but through all the size classes. Cyclone separation performance is represented by individual size recoveries to underflow. When these two unit operation performances are entered into the circuit modelling program (Streamline™), along with the circuit feed rate and size distribution, all the circuit survey size distributions and mass flows are perfectly regenerated by the program. The many issues associated with the historical Epstein (breakage-selection) models are eliminated. Once the circuit program is populated, pump and cyclone performance changes can be evaluated using a step-by-step procedure in order to maximize Classification System Efficiency. Mill water use and media sizing opportunities are also diagnosed in order to maximize Mill Grinding Efficiency at the size of interest. An example is provided. This circuit analysis and modelling system, and related training, is provided through a web-based application.IntroductionSince its development (McIvor, 1988), the Functional Performance Equation for ball milling has facilitated new understanding of industrial circuit cause and effect relationships, leading to significant strides in operational performance. Success stories of this refreshing approach to plant circuit performance improvement are now too numerous to list. Finch and McIvor (circa 1986) also discovered that the Functional Performance “Mill Grinding Rate” at the size of interest was the same cumulative grinding rate that is calculated from mill feed and discharge size distributions using a first-order rate equation. By calculating these cumulative grinding rates for all screen sizes, a complete ball mill model is generated (as used by Finch and Ramirez, 1981). Others in industry, Hinde and Kalala (2009), for example, have noted the same. Lacking the complexity needed to maintain their interest, most researchers have ignored this model, broadly opting instead for Epstein’s (1948) characterization of grinding as a chemical reaction, combining “selection rate” and “breakage size distribution” functions. The much simpler ball mill model presented here has previously been incorporated into a proprietary circuit modeling program (McIvor, 2005) and used for plant improvement work (for example, see McIvor and Finch, 2007, and McIvor, 2014). Now, by combining this extremely business-friendly ball mill model with optimization criteria from Functional Performance Analysis, a circuit modeling system (including the needed supplementary steps to assure successful plant implementation of circuit design changes) is at the disposal of every plant metallurgist, grinding equipment/material provider, and circuit designer."

Jan 1, 2017

By W W. Moorhouse

A survey of recent literature indicates that sulphides occur in the volcanic rocks of the Archean, or in sedimentary rocks intercalated with the volcanic rocks. The thick sedimentary sections are generally poor in sulphides. Thus, the widespread pyrite and pyrrhotite mineralization in the Archean may be largely of volcanic origin. Introduction I N this paper, commercial base-metal deposits will not be considered, as they are dealt with in other papers of the Symposium. Instead, attention will be focused on those sulphides, often associated with graphitic argillites or tuffs, which have appeared in such embarrassing abundance in electromagnetic surveys of Archean areas. The data on which the paper is based are drawn from recent reports of the Ontario Department of Mines, the Quebec Department of Natural Resources and the Geological Survey of Canada. The information available from these sources is unfortunately limited, because sulphides commonly occur in sheared rocks, such as black argillites and tuffs, which rarely form conspicuous outcrops, and may not be exposed at all. Thus, in the absence of geophysical information, even detailed mapping may fail to reveal the presence of sulphide-rich rocks.

Jan 1, 1965

By Ioannis K. Kapageridis

The lignite deposits of the Kozani-Ptolemais-Amyntaio basin in western Macedonia (North-West Greece) present a difficult modelling problem. Each deposit consists of several thin lignite layers ranging from a few centimetres to a few tens of centimeters in thickness, and thin intercalated sterile layers of marly limestones, marls, clays, and sands. These layers are practically impossible to model individually due to fast lateral transition of lignite layers to humus clay and vice versa and the lack of reliable and detailed stratigraphic correlation, leading to compositing methods being applied prior to any interpolation and modelling. The complexity of the deposit is further increased by the presence of a number of faults. This paper presents the modelling and estimation procedures applied during the most recent study of the South Western Field ? a new deposit that is considered for development and lignite production over the next years and will support the operation of a new power station in the area. Special focus is given to drillhole database structuring, fault modelling, stratigraphic correlation, mineable lignite intervals compositing, and resource estimation. The use of specialised mine planning software in all stages of modelling and estimation is thoroughly explained.

Oct 1, 2009

By Ivan Malinsky, Gérard Castonguay

"On a développé un procédé qui donne une fonte (2,3% C, 0,07% V) du V2O5 (99%) et un rutile synthétique (94% TiO2) à partir d'un minerai, dont les réserves au Québec sont importantes. Le procédé comprend les opérations suivantes: 1) la concentration magnétique du minerai (30% Fe, 9% TiO2 et 0,65% V2O5) pour produire un concentré (65% Fe, 7% TiO2 et 1,6% V2O5); 2) le smeltage du concentré aggloméré dans un four à arc, sans fondant, pour produire une fonte et une scorie (30% FeO, 40% TiO2 et 8,0% V2O5) qui contient plus de 95% du vanadium et du titane présents dans le concentré; 3) le grillage alcalin (37% Na2CO3) de la scorie suivi d'une lixiviation à l'eau et de la précipitation de l'hexavanadate d'ammonium à partir du filtrat; 4) la lixiviation du résidu par l'acide sulfurique pur ou usagé pour produire un rutile synthétique. Un estimé préliminaire de la valeur économique du projet laisse croire à sa rentabilité à la condition que l'investissement pour le smeltage soit inférieur à environ 400$/tonne de fer.IntroductionLes gisements de magnétites titanifères sont nombreux dans le monde. Ils consistent en une magnétite étroitement liée a l'ilménite, La teneur trop élevée en TiO2 empêche l'exploitation de ces gisements pour la production de fer. Cependant, dans certains cas, la magnétite a une teneur intéressante en vanadium qui peut rendre l'exploitation de ces gisements rentable. Aujourd'hui, les magnétites titanifères constituent la plus importante source de production de vanadium. On estime qu'environ 70% du vanadium produit provient de ces sources."

Jan 1, 1983

By R. M. de Carvalho

Empirical and phenomenological models of SAG and AG mills have dominated the scene for the last few decades, being used nearly every time a mill is scale-up or an attempt is made to improve its performance. However, in spite of their success, these models fail to describe the details of both the grinding environment and the breakage mechanisms. The result is a generally good track record, with a few ? but very important ? instances when these models fall short in their predictions, which can be very costly. Further, nearly all of these models require detailed calibration to industrial and pilot plant data, being costly in their application, although still with limited predictive capabilities. Recognizing these challenges, a new model framework has been proposed which overcomes the limitations of currently used models by coupling the microscale population balance model, the discrete element model and functions that describe internal classification at the mill grate. This model framework has already been applied to describe breakage in ball mills, with showing very promising results. However, in the case of SAG and AG mills a much greater level of complexity is involved in the model, given the interaction between the mechanical environment that is formed totally or, in part, by the ore itself, and the breakage response in the mill. The paper describes the model framework, demonstrating how it can address appropriately effects such as mill speed, mill filling and size distribution, on the response from the mill. Some of the advantages of the model are related to its intrinsic multi-component and dynamic nature, which allows simulating appropriately mixtures of ores of different competences in a transient manner.

Jan 1, 2012

By E. H. Smith

"The El Indio mine treats a complex mixture of copper and gold/silver ores at its plant located in the high Andes in Chile. The plant utilizes conventional crushing, grinding and flotation to produce a copper/gold/silver concentrate. Due to high levels of arsenic and antimony, the flotation concentrate must be roasted prior to custom smelting. The flotation tailings is leached and additional gold recovered from a CIP circuit. Present and future metallurgical developments are discussed in this paper. INTRODUCTIONIn late 1989, LAC Minerals purchased 65 % of Bond International Gold and as a result became controlling shareholder of the El Indio Mine through Bond and San Jose.El Indio is a world class, complex sulphide gold deposit located in the hydrothermal alteration belt of the Andes mountains in the 4th Region of Chile. The mine is located in the high Andes about 185 km east of La Serena at an elevation of 4000 meters. The 1450 workers at El Indio live in the mine camp at 3200 m and on days off are bussed to La Serena.The El Indio mine was started in 1979 by St. Joe Minerals Corp., bought by Bond in 1987 and subsequently by LAC in 1989. The mine has produced 2.7 million oz. of gold, 9.5 million oz. of silver and 170,000 t of copper since start of operation. The mill is currently operating at a rate of 2850 t/d and producing a copper/gold concentrate which is roasted to produce a copper/gold calcine and high quality, saleable crude AS2O3 . A small proportion of the precious metals are also produced as bullion from the leach circuit.Total production during 1989 was 224,197 ounces of gold, 1,309,342 ounces of silver and 26,968 tonnes of copper. The average cash cost of production for the period was U.S. $96 per ounce of gold, net of by-product credits. The average realized price was $5. 30 per ounce of silver and $1.14 per pound of copper."

Jan 1, 1991

By L. P. Srivastava

Rock bolts have been used since long to enhance the shear strength response of jointed rocks in civil and mining engineering structures. However, the assessment of strength response of a rock mass reinforced with rock bolts remains an unresolved problem till date. In the present article, an attempt has been made to study, through physical model tests, the shear strength enhancement of a blocky mass due to provision of passive rock bolts. Direct shear tests were conducted on large specimens of size 750 mm x 750 mm x 900 mm of rock mass under a normal stress varying from 0 to 2.0 MPa. Concrete was used as a model material to simulate intact rock and, elemental blocks of size 150 mm x 150 mm x 150 mm were used to form the mass specimens. Steel bolts of 6 mm diameter with 2 mm thick grout were used to reinforce the mass. Three different configurations of bolts were adopted. Observations were made on shear stress, horizontal shear displacement, and dilation during the tests. Effect of normal stress and reinforcement on peak shear stress and shear stiffness was studied. It is observed that the rock bolts enhance the shear strength of the mass by preventing sliding along the shearing plane, and by inducing additional normal stress due to tension mobilized in the bolts. The rock mass, therefore, becomes stronger due to the high degree of interlocking produced by the bolts. Shear strength of the mass increases with increasing numbers of bolts. In the case of reinforced mass, the enhancement in shear strength due to provision of bolts decreases with an increase in normal stress. The provision of bolts improves the cohesion of joints substantially. The effect on friction angle is low. The shear strength enhancement depends on the area of the bolts, spacing of the joints, spacing between the bolts and the cohesion of the intact material. A correlation has been established using which the enhancement in shear strength due to the provision of bolts can be assessed.

Jan 1, 2015

By Carlos F. Perucca

"Potassium is one of the three basic plant nutrients along with nitrogen and phosphorus. There is no substitute for potassium compounds in agriculture; they are essential to maintain and expand food production.Potash is extracted from buried ancient evaporites by underground or solution mining. This accounts for most of the potassium produced. Another important source is brine from landlocked water bodies, such as the Dead Sea, Salar de Atacama or Great Salt Lake.About 95% of potash produced worldwide is used in agriculture. The rest is found in several other industrial uses, including glass manufacturing, soaps, plastics and pharmaceuticals.Currently, three producers: IMC, PCS and Agrium operate 8 conventional and two solution mines in Saskatchewan, five of which run froth flotation circuits, two heavy media-flotation, two run forced crystallization and one natural crystallization.Potash in SaskatchewanPotash was discovered in Saskatchewan in the early 1940’s while drilling for oil. The deposits lie diagonally across the southern plains of Saskatchewan sloping southerly from a 1,000m depth at Saskatoon to more than 1,600 m depth at Belle Plaine and up to 3,000 m in depth in North Dakota. The known deposits are massive, accounting for more than 40% of the world’s known reserves."

Jan 1, 2003

By G. H. Hope

"Pamour Porcupine Mines of Timmins, Ontario operates two 3,000 ton per day concentrators which receive ore from eight to ten mines in the area. The area milling concept was adopted by Pamour in 1971 and has been used successfully since then. The purpose of this paper is to discuss the advantages and the problems of area milling. Pamour Porcupine Mines Limited operates two 3,000 ton per day concentrators which receive ore from eight to ten mines in the Porcupine region. The area milling concept was adopted as the route to survival for Pamour and has worked successfully. HISTORICAL BACKGROUNDProduction of gold from the Porcupine region in Northern Ontario started in the early 1900's and has been continuous since that time. Some of the major operators were companies such as Mcintyre, Hollinger, Dome, Pamour, Paymaster and the list goes on. An underground survey would reveal hundreds of miles of drifts and raises. The main group of mines extends from South East of Timmins to the Pamour Mine, 15 miles to the east. During the lean years of the sixties when gold prices were low, labour costs were rising rapidly, and ore grades were dropping, many of the area mines closed down their operations."

Jan 1, 1981

By R. H. Duthie

As at any other mine in Canada, grade control procedures are used at Steep Rock Iron Mines (1) in order to ensure that concentrator and pellet-plant operator s have a uniform feed so that they can manufacture a pellet to suit buyers' specifications and (2) to maximize ore recovery so that as little as possible finds its way to the waste dump or is downgraded by contamination. At Steep Rock, material grading 40% to 66 % Fe is considered ore. The ore may contain up to 10% sulphur. These ranges create six different stock pile types, with the possibility of more if large concentrations of arsenic are encountered. Although grading and mining techniques used to accomplish these ends are fairly standard, there is an appreciation and willingness by hourly and staff pit personnel to make grade control effective. This produces vertical and horizontal communication, which is necessary for success in this field. At Steep Rock, the waste-to-ore ratio is greater than at any other iron ore mine in Canada. Also, a high percentage of the ore mined is direct pellet feed. For these reasons, .grade control is very important.

Jan 1, 1977

By N. Dobrin, R. Sheinman, Y. V. Kokotov, L. N. Braginsky

Increasing the production of a Mixer-Settler unit requires either increasing flow rates or increasing extractant concentration. The mixers still have to ensure complete emulsification and to maintain high values of specific interface surface area in order to provide a high rate of mass transfer. Theoretically, an increase in mixing intensity can support increased flow rates without reducing extraction efficiency. Unfortunately, conventional pump mixers and mixing systems create small droplets that do not separate easily. As pumping action and mixing intensities are increased, the quantity of small droplets increases. We describe the development and industrial application of a novel mixing system for efficient mass transfer without forming significant quantities of small droplets, targeting both high mass transfer rate and low entrainment values.

Jan 1, 2014

By P. Mark. Hawley

Development of Barrick Gold?s Pierina Gold Mine in north-central Peru requires construction of a waste dump for disposal of non-ore grade materials stripped from the open pit to expose the ore. The waste dump site is located near the open pit in a U-shaped valley that is underlain by thin colluvial and morainal soils with locally thick peats and glaciolacustrine deposits. Bedrock underlying the site consists of variably weathered volcanics. The site is subject to moderately high seasonal rainfall and significant seismicity. The geotechnical quality of the waste rock is highly variable, ranging from low quality, degradable, soil-like materials containing appreciable quantities of silt and clay, to high quality, hard, durable, blocky waste rock. A hybrid dump design concept was developed that requires in-pit segregation of high and low quality waste, and selective placement of materials in the dump to maximize stability and enhance internal and subsurface drainage. The design includes a rock drain beneath the dump along the axis of the valley and a series of connected finger drains. Extensive peripheral diversions and stormwater control measures to inhibit infiltration of precipitation are also included. This paper discusses the unique challenges presented by the site and waste materials, the design methodology and stability analyses, and planned monitoring systems.

May 1, 2002

By W. Pawlak, J. Janiak, C. Rodkiewicz, B. Ignasiak

"There is a general consensus that, in order to widen the utilization of Western Canadian coals, a major effort must be devoted to their transportation, utilization of fines, beneficiation and mining techniques. It is postulated that the concept studied extensively over the last four years at Alberta Research Council (ARC), and based on a combination of hydraulic mining, selective agglomeration with bitumen and/ or heavy oil, pipeline transportation and oil recovery from agglomerates, offers a particularly attractive solution to the problems associated with extraction, beneficiation, transportation and utilization of Western bituminous and subbituminous coals. Results of preliminary experimental work on the feasibility of pipeline agglomeration of metallurgical coal and hydraulic transportation of agglomerates are presented and discussed in the context of conventional agglomeration techniques in stirred tanks. IntroductionAlberta is endowed with enormous reserves of low-sulphur coals which could attract considerable attention of potential customers, but the remote location of this province handicaps its competitiveness on the world market. It is known that Alberta's Cretaceous, particularly metallurgical, coals differ significantly from their Carboniferous counterparts; current R&D work on indigenous coals should continue to expand in order to encourage overseas client s to use these coals more extensively.There is a genera l consensus that, in order to widen the utilization of Western coals, a major effort must be devoted to their transportation, utilization of fines, beneficiation and mining techniques."

Jan 1, 1986