Search Documents

By A. S. Nortjé

At South Deep Gold Mine longhole stopes are backfilled using a cemented Cyclone Classified Tailings in its hydraulic state. The need to contain the hydraulic fill until cured requires a barricade. Due to the massive size of the stopes, the tailings can exert enormous forces on any such barricade. Barricades have long been in use, but recent failures in Australia and the large rate of filling required at South Deep solicited a robust design. A robust design must examine all foreseeable failures and the barricade must be able to resist all expected and, within limits, unexpected loads. The design should also be simple to construct and cost effective, limiting the impact of construction errors and unnecessary delays to production.

May 1, 2007

By J. T. Fyles, C. G. Hewlett

"THE REEVES MACDONALD mine is in the Sa Imo-Pend d'Oreille mining area of southeastern British Columbia. It is on the Nelway-Waneta road 4 miles west of the border-crossing point of Nelway. The Reeves orebody from which all production has come is one of several mineralized zones in easterly-striking limestones occurring between the Pend d'Oreille and the lower part of Salmo River.The property was originally located as two groups of claims by R. M, Reeves and J. H. McDonald. The two groups were consolidated in 1925. and extensive development work was done from then until 1930 and again in 1937, but no ore was shipped. The mine was reopened in 1947 and, between 1949 and 1953, 1,057,804 tons of ore was mined. Concentrates recovered contained 85,626 ounces of silver, 19,394,092 pounds of lead, 72,076,495 pounds of zinc, and 455,051 pounds of cadmium. Low metal prices forced the mine to close in 1953, but operations were resumed in November, 1955.The orebodies at the Reeves MacDonald mine are steeply plunging lead and zinc sulphide replacement deposits in a banded limestone named the Reeves limestone. The orebodies contain pyrite, honey-coloured sphalerite, and galena, and are surrounded by a dolomitized zone. In the Reeves orebody, where the relationships are known, the dolomite has the same general shape as the orebody. Four zones of sulphides are known on the property (see Figure 1). Three of these, the Reeves, B. L., and O'Donnell, are believed to be faulted segments of one mineralized zone. The fourth, the Point ore zone, exposed on the north bank of the Pend d'Oreille River, is not developed and its structural position is not known, but it appears to be a separate deposit."

Jan 1, 1949

By A. A. Paoli

The selection of a mining plant for carrying on development work presents many problems distinct in themselves, and affected by various local factors. In this paper, the writer proposes outlining and discussing in some detail the chief factors governing the economic selection of such plants. This will be followed by an enumeration of the underground and surface plant required for carrying on several hypothetical exploratory and mining operations. Where it is impossible or not convenient to obtain hydro-electric power, and where wood for fuel is scarce, we now find oil engines being used. A 100 h.p. oil engine, such as would be required to operate a three-drill air compressor, consumes approximately five Imperial gallons of fuel-oil per hour at full load. On the basis of a 60 per cent load factor, this gives, for eight hours' operation, a probable actual consumption of twenty-four Imperial gallons.

Jan 1, 1929

By J. Lobel, M. Bourassa, J. A. Kozinski, B. Peng

Non-isothermal kinetics studies of the reduction phenomenon of electric arc furnace (EAF) dust generated in stainless steelmaking have been carried out. The dust was mixed with carbon as a reducing agent and dolomite as a binder to form pellets. A Thermo-Gravimetric Analyzer (TGA) was used to determine the weight loss of pellets heated at an average rate of 40 K/min. up to a temperature of 1500°C. The degree of metal reduction was calculated by considering the pellet weight loss, and evaporation of moisture, dust, zinc and lead at high temperature. The reduction process was divided into three different steps. The first covers the 300°C to 760°C temperature range (from 7 to 18 min.), the second step ranges between 760°C and 980°C (18 to 24 min.), and the third covers temperatures above 980°C. Each step is characterized by different chemical reactions. Non-isothermal reduction kinetics equations were set up to describe each step. The kinetics parameters such as apparent activation energies and frequency factors were established. It was found that the first step was chemically controlled, while the second step was diffusion-controlled. Reduction behaviour in the third step was strongly dependent on the initial carbon content in the pellet. Chromium oxide (CrO) could only be reduced in this last step. High temperatures and higher initial carbon content favoured the reduction of CrO.

Jan 1, 2001

By T. Lamb

There are many honor stories about aluminum in the marine environment and many are not based on facts, so they are myths. Myths must be addressed before progress can be made. This paper attempts to dispel the myths and state the facts. A common perception is that aluminum ships cost significantly more than steel ships. This paper illustrates that even though the cost of the aluminum structure is over 50% more than the steel structure, an "equivalent" aluminum naval ship can be built within 7% of the acquisition price of a steel ship. This is possible because of the cascading benefits of the aluminum ship's significantly lighter weight. Aluminum ships also have a life-cycle cost advantage over steel ships because of reduced maintenance and fuel cost savings.

Jan 1, 2011

By Y. Guglielmi, C. Gout, P. Henry, P. Dick

The key questions about fault reactivation in shales concern the potential enhanced fluid displacement through a previously low-permeability aseismic shale formation. Here we selected a critically-stressed fault cross-cutting the underground research facility of Tournemire (France) which is located in Toarcian shales. Several inclined boreholes were drilled across the 8.5 m thick fault zone characterized by a fractured damage zone (FDZ) and a central 2.4 m thick complex core (FC) made of multiple shear bands with gouge intercalated with highly fractured lenses. The fault was pressurized using a straddle packer system defining a 2.4m long injection chamber normal to the fault surface. Three fault zone intervals were tested, two in the fault damage zone and one in the fault core. A three-dimensional displacement sensor set in the chamber allowed continuous synchronous coupled monitoring of fault movements, injection pressure and flow rate. An anticlockwise 0.22-to-0.05 mm fault slip was captured associated with a 10-to-100 hydraulic aperture increase of the fault. Preliminary analyses of the experiments show that leakage in the fault zone is controlled by strength and stress magnitude contrasts between the fault core and the fault damage zone. Fault damage zone discontinuities display a much higher peak static friction angle than the fault core shear zones, respectively of 34 and 22° that could be related to complex interactions between healing and sealing processes. Fault core leakage is much more dependent on strain than on effective stress variations. Discontinuous, pulse-like leakage, develops following complex failure processes that may simultaneously take place in the gouge zones and along the large pre-existing discontinuities. Such results may be of importance in evaluating fault seal integrity in oil and gas exploration, production or CO2 storage or underground excavations monitoring.

Jan 1, 2015

The Santa Rita mine is located in north eastern part of Bahia in Brazil and is owned and operated by Mirabela Mineração do Brasil Ltda. Typical SABC circuit was designed as the preferred option for the 4.0 mtpa (500tph) to produce a P80 of 125um for flotation. Although the SAG was originally designed to operate with conventional radial pulp lifters, later it was fitted with Outotec?s Turbo Pulp Lifters ? TPL (Latchireddi, 2005). The milling circuit commenced commissioning on the 24th of October 2009 and the milling circuit achieved the nameplate capacity within days. with small and relatively simple measures to rectify. Since commissioning, the SAG mill has been working in fully autogenous grinding (FAG) mode with no balls (in contrast to the estimated 10% ball charge) and has been consistently treated up to 650tph. This paper examines the comminution design process, the operating philosophies, start-up experiences, post commissioning optimization and future development works. An evaluation of mill performance relative to the design criteria for the project life to date is also included.

Jan 1, 2012

By J. D. Clucas, N. Verbaan, T. Grammatikopoulos, D. B. Dreisinger, C. Forstner, M. Aghamirian

"Search Minerals is currently exploring the Port Hope Simpson (PHS) Rare Earth Element District in southeastern Labrador, Canada. The Foxtrot Rare Earth Element (REE) Project in the PHS District has a 43-101 resource estimate consisting of 3,410,000 tonnes of Indicated Mineral Resources and 5,850,000 tonnes of Inferred Mineral Resources. The indicated and inferred resources contain 1.07% and 0.98% total rare earth element oxide (including yttrium), respectively. The dysprosium and neodymium grades are particularly attractive at 218 ppm Dy2O3 and 1687 ppm Nd2O3 for the indicated resources and 208 ppm Dy2O3 and 1494 ppm Nd2O3 for the inferred resources. The mineralization remains open along strike and at depth and is only one of a number of attractive exploration targets in the Port Hope Simpson area. The REE minerals fergusonite and allanite are present. The ore can be beneficiated by gravity, magnetic separation and flotation to a recovery of +80% for the individual REE. Acid bake and water leaching may be used to extract REE into solution for subsequent purification and recovery. The extraction range for single stage leach tests were 91-96% for Nd, 84-87% for Tm and 92-94 % for Dy with modest acid consumptions. INTRODUCTIONSearch Minerals Inc. (Search) is exploring the 100% owned Port Hope - Simpson District in Labrador, Canada for rare earth elements (REE). This District is approximately 135 km by 12 km in size, and is highly prospective for heavy and light rare earth elements. A total of 11 REE prospects have been discovered in the District to date, including the Foxtrot. In addition, Search is exploring in the 100% owned Henley Harbour region and has joint ventures with Quest Rare Minerals in the Strange Lake region, and with Great Western Minerals Group in the Red Wine complex, all in Labrador. These exploration locations are illustrated in the Figure 1. The focus of this paper is the investigation of the mineralogy and processing of Foxtrot REE materials. The Foxtrot resource falls within the claims held by Search in the Port Hope Simpson REE District. The infrastructure available at Foxtrot is excellent with a deep water port, air strip and road and power infrastructure at Port Hope Simpson. Over $7 Million has been spent to date on exploration and development of the District. The Foxtrot has been explored using prospecting geochemical methods, geophysics (airborne and ground), channel sampling of surface outcrops, mapping and three phases of drilling (18,934 m total)."

Jan 1, 2012

By Chuck Edwards

"Cameco operates the high-grade McArthur River uranium mine in northern Saskatchewan, and is constructing the high-grade Cigar Lake uranium mine. Cameco has studied the concept of underground milling of high-grade uranium ore. Compared to conventional milling on surface, the underground milling scheme appears to offer significant cost savings and a lower environmental impact. This paper describes the underground milling scheme, presents process flowsheets and plant layouts, and provides an assessment of potential benefits from underground milling.INTRODUCTIONCameco CorporationCameco is the world’s largest uranium producer, with three operations in Saskatchewan (Rabbit Lake mine/mill, McArthur River mine, and Key Lake mill), two in the United States (Crow Butte and Smith/Highland ISL operations) and two new mines being developed in Canada (Cigar Lake project) and Kazakhstan (Inkai project). Cameco provides uranium fuel refining and conversion services at its Blind River and Port Hope facilities in Ontario. Cameco is part owner (31.6%) of Bruce Power that leases eight nuclear power plants located in southern Ontario. Cameco is the majority shareholder in Centerra Gold Inc., which operates gold mines in the Kyrgyz Republic and in Mongolia.Global Uranium Production RequirementsCentral to Cameco’s view of future uranium supply requirements is the belief that the world is experiencing a nuclear renaissance. This belief is supported by a number of developments, including:•,?Countries representing half the world’s population are now constructing new nuclear power plants. Many countries without nuclear power have begun to plan for it, seeking reliability, clean air and energy independence.•,?Accelerated growth for this industry is also becoming much more likely. In Asia, primarily in China and India, 92 reactors are under construction, on order or planned to help meet rapidly expanding economic needs. Other Asian countries, such as Vietnam and Indonesia, with large populations and rapidly growing economies, are also expected to follow.•,?In the United States the “Energy Policy Act of 2005”, the first energy legislation introduced in over a decade, was signed. This legislation includes provisions recognizing, for the first time at a national level, the clean air contribution of nuclear energy and its critical role in meeting energy security. Upon signing this landmark legislation President Bush stated, “We will start building nuclear power plants by the end of this decade.”"

Jan 1, 2007

By D. F. Sherwin

"THE AREA which is described in this paper (Fig. 1) includes the continental margin of eastern Canada extending from the Gulf of Maine to the north edge of the Grand Banks, which, including the continental shelf, slope and rise, comprises an area of about 600,000 square miles. The paper is intended to give a background of the geological setting of this region in the context of its ultimate potential for oil and gas reserves in close proximity to the Nova Scotia energy market.HISTORY OF EXPLORATIONThe history of geological exploration of this area really began in 1878, when U.S. fishing boats brought back samples of rock recovered in trawls from their expeditions to the long-famous fishing banks off Canada's East Coast. Tertiary and Cretaceous fossils recovered from these samples indicated that the eastern Canadian continental shelf was actually the submerged northern extension of the Atlantic Coastal Plain."

Jan 1, 1972

By Q. F. Wang, M. H. Lai, T. Q. Liu, G. G. Dong

Compared with the traditional pre-treatment process, biological oxidation process has many advantages including higher gold recovery, less cost, easier operation. The bio-oxidation reactor is the most important equipment for biological oxidation process. In this paper, the characteristics of biological oxidation are investigated, and the design principles are proposed based on laboratory tests. Both increasing the tank height and taking new inflation system can enhance higher dissolved oxygen. The new type of large-scale industrial bio-oxidation reactor is designed, which is 9.5 m in diameter and 10 m in height. The bio-oxidation reactor metallurgical performance has been tested by industrial-scale experiment. The slurry of flotation concentrate is divided into two parts to feed two bio-oxidation reactors. The feeding rates of two reactors are adjusted on the basis of getting the same content of S, Fe, As in overflow. The result shows that the feeding rate of the new type of 700 m3 bio-oxidation reactor is 3.72 m3 per hour, and the feed rate of the conventional 700 m3 bio-oxidation reactor was 3.23 m3 per hour. The processing capacity of the former is 15.2% higher than that of the later, which demonstrates the new type of bio-oxidation reactor has higher oxidation rate.

Jan 1, 2015

By R. Khanna, I. Mansuri, S. Devasahayam

"Recycling polymer based end-of-life materials as carbon resources for a partial replacement of coke/coal can make important contributions towards enhancing the environmental sustainability of steelmaking processes. An in-depth high temperature (1550°C) investigation has been carried on waste CDs/DVDs focussed specifically on char generation, characterization and dissolution into molten iron. The simultaneous presence of carbon and oxygen in polymeric chains on polycarbonate substrates resulted in the generation of a significant pore structure and exposed surfaces. Carbon dissolution studies into molten iron were carried out on the raw polymer as well on chars; high levels of carbon pick-up were observed in both cases after 15 minutes of contact at high temperatures. INTRODUCTIONOver the past sixty years, plastics have played an important part of our daily lives and are being increasingly used in all aspects of the global economy. More than 260 million tons of plastics are produced annually worldwide. Their rapid growth and extensive utilization with a short life span (such as packaging) has created a massive waste problem. Although the waste plastic component in municipal solid waste (MSW) amounts to only about 10 %, plastics have a high volume-to-weight ratio and these are generally not biodegradable. In Australia, ~19.20 % of plastics were recycled in 2009-2010 (PACIA, 2010); with the total consumption being estimated at 1,501,258 tonnes, 288,194 tonnes of plastics were recycled. There are serious environmental concerns with the two key waste management options, i.e. land filling and incineration, and there exists an urgent need for developing alternative recycling approaches. In this paper, we focus our attention on recycling waste CDs/DVDs polycarbonate substrates as a carbon resource in steelmaking.CDs/DVDs used for music/data/image are made from aromatic polycarbonate resin (hereafter abbreviated PC). This resin is also widely used as an engineering plastic in applications such as automobiles, mobile phones, notebook type personal computers, cameras & video cameras, electric & electronic appliances, fire equipment, life & living goods, roofing sheets, etc. High consumption and growth (~10% annually) of PC utilization is attributed to its excellent properties such as outstanding impact resistance, transparency, heat resistance, and dimensional stability. The molecular formula and composition of PC resin is given below:"

Jan 1, 2012

By Leslie F. Sawatsky

Raw water import requirements for oils sands mines depends mainly on factors such as ore processing rate, ore material characteristics, tailings processing technology, tailings storage systems, process water storage operations, the phase of tailings production, and non-recoverable seepage losses from tailings ponds. These factors can be readily quantified to calculate raw water import needs. Nevertheless, mine water balance continues to be misunderstood by some regulators, stakeholders and possibly even mine operators. Confusion over consumptive uses has led to a focus on recycling which is not necessarily applicable to a closed circuit water management system. Some water conservationists focus attention on raw water intake rules instead of the technical decisions that control consumptive uses. Typical oil sands mine water balances for various types of tailings operations, are analyzed to illustrate the effect of controllable and uncontrollable parameters as well as major options that need to be explored for reducing water demand. Uncontrollable parameters including tailings fines content, oil content of ore, connate water, mine depressurization water inflows and surface water hydrology. Controllable parameters include storage operations, advance water supply ahead of mining operations, type of tailings operation, net tailings pond seepage losses, and tailings impoundment operations. Potential reductions of raw water supply rates may be obtained by providing greater on-site storage to attenuate fluctuation in water demand, advance water accumulation prior to mine start up, early commencement of CT operations, thickened tailings disposal and paste technology. Water conservation measures should be focused on reducing on-site process water storage and water content of tailings material.

May 1, 2004

By Francis Chachula, Niel Erasmus

"In 2002, Titanium Corporation Inc. focused its attention on the development of a process for the recovery of valuable heavy minerals, including zircon and titanium bearing minerals from oil sands froth treatment tailings. The development of a process flowsheet to recover the titanium and zircon minerals from the Athabasca oil sand tailings has evolved through many laboratory, bench and pilot scale iterations.Initial development work focused on so-called ‘beach sand’ material, which is tailings material deposited over a period of time close to the tailings pipe discharge. The derived process flowsheet primarily consisted of gravity concentration stages, which is typical of all mineral sands operations. Titanium Corporation’s business plan calls for the utilization of tailings directly from the tailings pipeline – the process developed around the beach material is therefore risky as it differs from the live tailings in a number of aspects, with the effects on the process unknown. Titanium Corporation successfully obtained an intermediate product through a ‘bulk sampling plant’ coupled directly to an Oil Sands operator’s froth treatment tailings pipeline, during the summer of 2005. Subsequent further processing of this material resulted in poor separation or concentration of the heavy minerals due to a number of reasons. A more effective process flowsheet had to be developed.The newly derived process is basically a marriage between mineral sands technology and oil sands technology that can economically concentrate and recover the heavy minerals and entails the incorporation of a flotation process that takes advantage of the entrained bitumen in the feed to separate the heavy mineral fraction from the quartz gangue This paper will describe the newly derived process as well as the successful results of a subsequent on-site concentrator pilot campaign completed during the 3rd Quarter of 2006."

Jan 1, 2008

By Rene Cane, V. I. Lakshmanan, John Starkey, Richard May

"The Agrium Kapuskasing Phosphate Operation mines and processes up to 6,000 t/d of phosphate ore. Run-of-mine crushing to minus 6 inches is done in a toothed roll-crusher, while grinding is done in a SAG/ball mill circuit with no coarse recycle classification of the SAG mill discharge. The primary grinding mill is an 18 ft. diameter x 9 ft. EGL, 1500 HP variable speed SAG mill and the secondary mill is a 13 ft. diameter x 21 ft. long, 2000 HP fixed speed, ball mill. When hard ore was treated, the SAG mill restricted the tonnage that could be ground. When soft ore was treated, the ball mill and spiral classifier overloaded and restricted throughput.Recommendations from a plant benchmark and an ore hardness testing program, on how to better utilize installed energy in the Agrium SAG mill when treating soft ore, and how to obtain best results when treating hard ore, were checked in a pilot plant investigation in the 3 ft. diameter Starkey-PRO Pilot SAG Mill. Correlation between the ore hardness testing and the results from the 3’ Pilot SAG mill was very good. In addition, the work indicated the results that could be expected for the different ore types when using either smaller SAG discharge grates and/or a vibrating screen with 10 mesh square opening cloth.INTRODUCTIONAgrium Kapuskasing Phosphate Operation consists of a 6800 t/d open pit mine and a concentrator, near the Town of Kapuskasing in Northern Ontario. The two major ore types are sandy ore and cemented ore. Sandy ore is fine, soft and easy to grind in the SAG mill while cemented ore is harder, more blocky and difficult to grind in the SAG mill. The ratio of sandy to cemented ore in the deposit is thought to be in the order of 80:20 but can range as high as 5050, so it was important for the grinding circuit to have the ability to treat sandy ore alone."

Jan 1, 2002

By Matthew Janes

Advantages: Clean samples Low sample disturbance Very low spoil Versatile Fast Penetrates all formations Resonant Drill 100 or 150 kW Self tuning to resonance Rotation to 100 rpm Increased depth in dense soil Increased productivity Reduce water use Reduce casing plugging

May 1, 2013

By C. T. Harper, B. J. Fryer, R. P. Taylor

"IntroductionThe Maurice Bay deposit is one of a number of uranium deposits that have been found in recent years in the Athabasca Basin of northern Saskatchewan (Tremblay, 1982). This deposit, along with the others, belongs to the unconformity type deposits (Beck, 1977). They are, for the most part, polymetallic, being characterized by a suite of metals which include U, Ni, Co, Cu, Pb, Zn, Mn, V, Ag, Au, Pt-group elements, S, As, Bi, Se, Te, and Mo, some of which, besides U, are present in economic concentrations (Amok, 1974; Ruzicka, 1975; Tapaninen, 1976; Hoeve and Sibbald, 1978; Dahlkamp, 1978). The Maurice Bay deposit was known to be a small low grade deposit in which the ore was essentially monomineralic, consisting mainly of pitchblende (Harper, 1978). However, the occurrence of trace amounts of some of the elements common in the larger polymetallic ore bodies (e.g. Key Lake, Cluff Lake D) was anticipated. Thus a lithogeochemical sampling project was undertaken in 1979 across part of the Maurice Bay deposit (Harper, 1979). Major oxides (SiO2, Al2O3, FeO, Fe2O, MgO, CaO, K2O, Na2O, MnO, P2O5, and TiO2) and a group of the most common trace metals (U, Ni, Co, Cu, Pb, As, Au, V, and Se) were analyzed to determine whether any elemental patterns (halos or depletions) could be detected which would reduce the number of pathfinder elements needed for exploration purposes. In addition to the above metals, Th was also checked because some conglomerate strata in the Maurice Bay area are known to be thorium-enriched (Harper, 1978). Only the trace metal distributions will be discussed in detail in this report.General GeologyThe Maurice Bay area is underlain by three major groups of rocks, the White Lake metamorphic complex, an unnamed granodiorite complex, and the Athabasca Group, described previously (Fig. 1; Harper, 1979). Table 1 summarizes the stratigraphic features as deduced by geological mapping and the examination of drill cores."

Jan 1, 1986

By F. R. Archibald

A STATEMENT on this subject by A. D. Turnbull, presented and discussed at the Annual Business Conference of the Metallurgy Division, C.I.M., held in Ottawa on April 22nd 1957, led to creation of a committee "too see if the Metallurgy Division of the C.I.M. can improve this situation". Without discounting the general problems of education and short-ages in other fields, the committee is primarily concerned with deficiencies related to metallurgy. The committee members are: F. R. Archibald, Chairman, A. D. Turnbull, L. E. Djingheuzian, J. U. Mac-Ewan, and L. M. Pidgeon. Following exchange of views among the committee members a general attitude of approach was established and a background of reference material assembled. It is the purpose of this review to acquaint those interested with the reference material, to offer an appraisal of the situation, and to suggest a programme for action by the Metallurgy Division of the C.I.M. Before proceeding with the ?presentation it is fitting to point out that, notwithstanding some rather important developments in public concern for educational matters, as well as changes in the level of activity in the metallurgical industry, the statement (April 1957) by Mr. Turnbull still stands as a sound article of reference.

Jan 1, 1958

By John Vergunst

"This paper traces the development of Ontario 's cap lamp standard. Over the years, numerous Coroner's Juries investigating fatal mine accidents have made recommendations with respect to underground lighting. As well, recommendations to improve mine lighting have been made by two Commissions, investigating mine safety in Ontario.During the past few years, the performance of any cap lamp worn by miners involved in serious accidents, have been measured by the Mining Heal/h and Safety Branch. Large variations in light output were found between and among cap lamp types. These variations have been attributed to the lack of quality control on the bulbs, design of the cap lamp head piece and in some cases, poor maintenance.In 1986, a series of underground tests were conducted to establish the minimum light output from cap lamps required to visually identify loose ground. The results of these tests indicated that a cap lamp should produce a minimum peak illuminance of 1500 lux measured at 1.2 metres from the light source. On May 30, 1987, Ontario became the first province in Canada to legislate the minimum amount of light required to visually assess ground conditions. INTRODUCTIONPoor lighting has been identified as a factor which can contribute to mining accidents. Over the past decade, several Coroner's Juries as a result of inquests into mining fatalities, have recommended improved lighting in mines.The Joint Federal-Provincial Inquiry Commission into Safety of Mines and Mining Plants in Ontario, was appointed to report upon the adequacy of existing arrangements and practice s that may affect safety. This Commission completed their report in April 1981, and recommended that inadequate lighting be investigated as a possible cause of all reportable underground accidents, and that a comprehensive research programinto mine lighting be undertaken.In response to the first recommendation, the Mining Health and Safety Branch of the Ministry of Labour, hereafter referred to as the Branch, initiated a program to measure lighting levels in all fatal accident investigations where inadequate lighting was a possible factor."

Jan 1, 1989

By F. Awotwe-Appiah, P. Koshy, J. Dankwah, J. R. Dankwah

This research investigates the generation of an effective carbonaceous material from waste ‘pure water sachets’ and their subsequent utilisation as reductants for the reduction of the Opon Mansi iron ore. Composite pellets of Opon Mansi iron ore and pulverised carbonaceous material generated from waste pure water sachets were heated from room temperature to 1200 °C in a gas fired furnace for seventy minutes. The reduced pellet was analysed chemically for its oxygen and carbon content using a LECO Oxygen/Nitrogen and LECO Carbon/Sulphur analysers, respectively. It was observed that nuggets of metallic iron were readily produced with the carbonaceous materials acting as an effective reductant and source of chemical energy. XRD analysis of waste ‘pure water sachets’ revealed that the polymer was semi-crystalline with peaks that were identical to those of high density polyethylene (HDPE). Gas emission behaviour of the iron ore-PWS pellet was studied in a horizontal tube furnace at 1200 °C using an infrared gas analyser; the results revealed an exhaust gas rich in the reducing gases CO and CH4 along with CO2.

Jan 1, 2015