Search Documents

By M. S. Millman

Close monitoring of performance at each process stage, from raw material through to finished product, is vital for operational consistency and the production of high quality steel. However, many of the integrated iron and steelmaking process route stages operate under such severe conditions of temperature, dust, water, thermal radiation, vibration, pressure, vacuum, extreme dynamic events, high material flows, corrosion, erosion, electrical-noise, electromagnetic-noise, or audio-noise that, in general, it is a very difficult challenge to obtain useful information for control. Thus, state-of-the-art non-contact and remote sensors are applied to help monitor and control specific process operations. Often, these sensor systems have been developed especially for the steel industry and they are based on four principal technologies: Laser, Microwave, Electro-Magnetics and Thermal Imaging with supporting technologies such as: X-ray Fluorescence, Audiometry, Digital Image Processing, Radio Telemetry, GPS and many others. These advanced sensor technologies are reviewed with respect to their application at various stages along the integrated process route.

Jan 1, 2004

By Leslie S. Weldon

THE Lake Shore mine has been developed by two vertical shafts, with level intervals at 200 feet to the 2200 level and at 125 feet below this horizon. A main cross-cut joins the two shafts on all levels to the bottom of No. 3 shaft, and opening into these cross-cuts are the ore passes and sand passes, which are completed from surface To the 4450 level. In the west part of the mine, additional connections have been made between No. 1 and No. 2 veins, through which the major part of the ore from No. 2 vein west is routed to drifts in No. 1 vein. With the lesser amount of stoping on No. 1 vein, this arrangement permits better haulage to be maintained. The ore passes are driven at 50 degrees from the ends of short cross-cuts off the main ones and are broken through to the levels above at the mouths of the short cross-cuts, to allow for dumping on each level. The passes are controlled at each level by ball-and-chain gates and deliver to crushers and thence to loading pockets, shown in Figure 1. That system is quite flexible in that it is possible to by-pass the crushers at any station and load from either shaft at a number of different pockets. The sand passes are driven from the main cross-cuts at the same inclination as, and parallel to, the ore passes. Each is equipped with a chute and dump hole, so that waste or sand fill may be loaded or dumped at each level. A transfer door, hinged on the bottom, is installed opposite the chute for by-passing fill from one level to the next, and in the closed position protects the opening at the top of the pass. The dump hole situated beside the transfer door is protected by a grizzly with 10-inch spaces. Waste rock may be withdrawn from the system through No. 3 shaft loading pocket at the 2950 level to a waste bin on surface. Levels are developed by drifts in No. 1 and No. 2 veins for their entire lengths. Subsidiary breaks are followed at a later date, when full information has been obtained by exploration, and a considerable amount of development by sub-drifts is carried out in the upper part of the mine, particularly in more or less erratic sections of No. 1 vein.

Jan 1, 1936

By Jean-Marie Fecteau

The gold mine sector is presently facing low gold prices as well as technological challenges. Its competitiveness and survival will depend on new mining methods and equipment to improve ore extraction. In 1999, Natural Resources Canada has invested new funds over a period of three years at CANMET?s Experimental Mine to establish the Narrow-Vein Mining Project. A team of engineers and researchers specialised in mining, mechanics and electronics engineering are working to meet the critical need of ore-extraction technology. CANMET?s program in mechanisation and automation for narrow vein mining had, prior to 1999, realised several important achievements, many in co-operation with a consortium of mining companies (Soredem). The investment of new funds in this area will contribute to develop technologies to improve the productivity, as well as health and safety conditions of the narrow vein mining industry. Several important impacts of this project will be monitored. Specifically, a database of methods and equipment used in narrow vein mining is being developed. A key thrust is to identify operators? needs with respect to the development and automation of mining methods and equipment. Based on those needs, research and development projects will be created. The main problems identified following meetings with mine operators are described with a few elements of solution and the Web site created for the broadcast of the results is presented.

Oct 1, 2001

By Gordon W. Hines

This paper, dealing with network planning in an industrial complex, discusses the type and size of project that can be handled on a manual basis. After a review of the fundamentals of network planning, and specifically of the Critical Path Method, the author analyses several different types of projects, each with its own characteristics. Some can be handled in conjunction with a computer, but others can be dealt with equally well without one. Among the projects discussed are a blast furnace reline, the installation of a billet mill flying shear, and routine maintenance-type operations.

Jan 1, 1967

By G. B. Harris

It has long been appreciated that chloride chemistry has a number of advantages over the more traditional sulphate route for both extracting and separating metals. Modern materials of construction, coupled with the development of a more cost-effective and efficient hydrochloric acid regeneration technology mean that chloride-based processes are now more competitive and attractive. Such processing routes are able to recover more of the contained metal values in a feed, including iron in a benign and/or marketable form, and particularly the so-called rare and rare-earth elements which are increasing in demand in our electronic age. These factors, therefore, add appreciably both to the overall economics of a project, but also offer a much more sustainable approach to our dwindling natural resources. Additionally, chloride-based flowsheets can be much more environmentally-friendly, offering practical alternatives to two of the biggest headaches faced by the industry, namely cyanide usage and the generation of red muds. This paper presents a brief theoretical background, focusing on the latest developments of ferrous iron oxidation and the low-temperature, selective hydrochloric acid regeneration process, which is the key unit operation for any chloride flowsheet, and discusses in general the advantages of the chloride approach. Several recently-developed flowsheets, which have been tested at the miniplant level, are presented for gold, base metals, titaniferous magnetites and lead-silver ores wherein the advantages of considering a chloride approach are highlighted.

Jan 1, 2014

Although Canadian bentonite is competitive in quality for most uses, it has not been accepted for the pelletizing of iron ore concentrates. In 1962, Canada consumed about 10,000 tons of imported bentonite for this use. By the end of 1965, the planned domestic consumption for this purpose alone will probably be more than 100,000 tons a year, valued at about $3 million. Consequently, a challenge exists for the establishment of a Canadian source of high-quality bentonite for pelletizing. Such a bentonite would also be suitable for the two other major applications -well drilling and foundry use. Brief mention is made of such topics as the identification, 1noperties, occurrences, exploration, applications, technology and laboratory testing of this clay. In particular, the type of bentonite in demand, the geological horizons warranting exploration, and simple preliminary test methods are discussed.

Jan 1, 1964

By S. Aram

Product Lifecycle Management (PLM) solutions have been serving as the basis for collaborative product definition, manufacturing, and service management in many industries. They capture and provide access to product and process information and preserve integrity of information throughout the lifecycle of a product. Efficient growth in the role of Building Information Modeling (BIM) can benefit vastly from unifying solutions to acquire, manage and make use of information and processes from various project and enterprise level systems, selectively adapting functionality from PLM systems. However, there are important differences between PLM?s target industries and the Architecture, Engineering, and Construction (AEC) industry characteristics that require modification and tailoring of some aspects of current PLM technology. In this study we examine the fundamental PLM functionalities that create synergy with the BIM-enabled AEC industry. We propose a conceptual model for the information flow and integration between BIM and PLM systems. Finally, we explore the differences between the AEC industry and traditional scope of service for PLM solutions.

Aug 1, 2013

By O E. Weightman

This paper describes the methods used for the ventilation of raises, sublevels and drawholes at Cominco's Sullivan mine. The problems involved in ventilation during blasting, drilling and scraping operations are first re-viewed, and then the air mover, a piece of equipment developed at the Sullivan mine, is described. The design of this device is discussed, along with the operating procedures used. Some figures are given to show the effectiveness of the method. THE Sullivan mine, located at Kimberley in the southeast corner of British Columbia, is owned and operated by The Consolidated Mining and Smelting Company of Canada Limited. Current daily production is approximately 10,000 tons. The mine is developed by sixteen levels over a vertical range of 2,000 feet. The total ventilation requirements, which amount to approximately 1,000,000 cubic feet per minute, are handled through a network of fresh air intake and foul air exhaust circuits. In addition to the many development and production headings, there are three crushing chambers and an extensive conveyor system which must be ventilated.

Jan 1, 1965

By S. Gaulocher

Gearless mill drives (GMDs) are the workhorse in the mineral processing industries, more specifically when it comes to grinding crushed ore and cement (in various production stages) in semiautogenous (SAG) mills and large ball mills. They are renowned for their excellent reliability and robustness, long lifespan, and little need for maintenance, and thus yield a low total cost of ownership (TCO). A GMD represents a major investment for a mineral processing plant, and its availability is pivotal for the grinding process. As a basic rule, shut-down periods are to be minimized, but even much more important is that unscheduled shut-downs be avoided. In this contribution, we will present a portfolio of innovative remote diagnostic that consist of the following three key components: 1. Trouble shooting is a form of corrective maintenance and is based on state-of-the art remote access technology, thus enabling highly skilled engineers to access the current sensor readings anytime and from anywhere in order to resolve urgent problems together with the GMD user. 2. Periodic maintenance reports are a form of preventive and predictive maintenance and aim at continuous improvement based on long-term historical records and analyses of multiple measured signals. These detailed reports highlight the health and operational status of the GMD and are periodically (e.g. 3 months) submitted to the customer. 3. Remote condition monitoring spans across preventive and predictive maintenance and is based on continuous recording and automatic analyses of relevant signals using advanced algorithms. The main issue is how to handle the enormous flood of data in an intelligent manner. The results of these analyses are made available to both the GMD user and supplier in real time in order to increase the availability and reliability of the GMD. In this paper, we consider various parts of the GMD, e.g. the cycloconverter, the ring motor, the auxiliary devices (e.g. cooling and lubrication systems), and also phenomena related to the mill itself (e.g. state and quantity of charge). The signal analysis techniques range from simple threshold-based analyses to complex time and frequency domain analyses. We will illustrate the benefits of the proposed approaches with some selected examples.

Jan 1, 2012

By M. Tiedtke, T. Crary, P. MacPhail, M. Ounpuu

"The SGS carbon-in-pulp (CIP) / carbon-in-leach (CIL) model was used to evaluate and optimize the carbon circuit at Alamos Gold’s Young-Davidson Mine. Plants samples (pulp and carbon) were tested in a series of small scale batch experiments to determine rates of gold leaching and adsorption on carbon from a combined flotation concentrate/tailing product. The testwork data, along with existing plant data were then used to model the performance of the existing CIL plant and optimize the circuit to improve performance and overall recovery. The primary purpose of the modelling exercise was to determine the most cost effective way to lower solution losses at the plant. The modelling was also used to learn how the various parameters in the CIL circuit affect solution losses and the gold inventory tied up on the carbon. This resulted in recommendations for minor changes in the CIL flowsheet, which were successfully implemented in the plant. The approach, results and plant changes are presented.INTRODUCTION This paper presents the details from testwork conducted on samples from Alamos Gold’s Young- Davidson gold mine which is located near the town of Matachewan, approximately 60 km west of Kirkland Lake in Northern Ontario, within the southwestern part of the Abitibi Greenstone Belt. The objective of the test program (completed by SGS Canada in 2013) was to investigate and model the combined flotation concentrate / tailing carbon-in-leach (CIL) circuit and suggest ways to improve gold recovery. The metallurgical test program included mineralogy, rheology, and carbon modelling testwork. Plant information was provided during the test program and used in the optimization process. Upon completion of the testwork, plant changes were recommended and implemented at site (October 2014). Plant results from 2014 to 2017 confirmed the modelling results."

Jan 1, 2018

Adaptive processing is often related to the mineral composition of the mining block currently processed. The portions of waste, ore and secondary product minerals considered are always positive and typically sum to 100% (i.e. a composition). A typical solution to predict block averages of spatially dependent quantities would be block kriging. However, kriging is based on spatial correlations and it has been repeatedly shown that correlations of compositional data are spurious and blurred by the constant sum constraint. Aitchison (1982) proposed a general solution for compositional problems, based on transforming the compositional data to a set of logarithms of ratios of components, and analysing the transformed scores. The transform is chosen to be invertible to ensure that no information is lost in the process. This methodology avoids spurious correlation problems and ensures coherence between results obtained with different subcompositions. Pawlowsky-Glahn and Olea (2004) adapted the approach for point-support geostatistics, allowing the prediction of point compositions from spatially neighbouring data, without the artefacts induced by standard multivariate cokriging. Unfortunately upscaling the results of this approach with block cokriging is not straightforward, because of the nonlinearity of logratio transforms. Furthermore, we have to consider those nonlinearities created by the dependence on the block composition of extraction efficiency and processing costs of the possible processing choices. This paper proposes a solution for predicting the conditional expectations of the benefit of processing the block with each processing choice using geostatistical simulations of the local values of the composition and the resulting block integrals. The computation for a large number of blocks can be done efficiently using Cholesky decomposition. The approach also allows the calculation of prediction errors for expected compositions and expected benefit at almost no additional computational cost. Such compositional approach is necessary, for example when processing choices depend on proportions of certain minerals after other components have been removed; or if processing alters the composition in a multiplicative way, by partially removing a portion of some components.

Aug 1, 2013

By Rodney Trevor Jones, Arthur Robert Barnes

Anglovaal Minerals acquired the Nkana slag dump from Zambia Consolidated Copper mines (ZCCM) in 1998 and embarked on an ambitious project to pioneer the recovery of cobalt from slag using DC smelting technology. Anglovaal Research Laboratories performed initial pioneering smelting tests in a 250 kW DC furnace over a 3-year period before engaging Mintek for three piloting campaigns at the 1.5 MW level. Mintek had previously developed a reductive smelting process, patented in 1995, using a DC arc furnace for the recovery of cobalt from slags. The results of the pilot-plant test campaigns were used as the basis for engineering the commercial 40 MW operation installed at Chambishi Metals plc in Zambia in 2001. This paper traces the development of understanding of the metallurgical fundamentals ultimately used to predict furnace performance, reviews some of the extreme technical challenges faced, how solutions were identified and highlights some of the critical issues identified during piloting and how these impacted both positively and negatively on the final commercial operation.

Jan 1, 2011

By Ernest Davis

WATER power, until developed, produces nothing, but when harnessed it continues to produce, it might be said, indefinitely. Hence the importance of developing all feasible water powers. British Columbia, like the western states of America, is subject to variable meteorological conditions which cause most streams to be erratic in their flow. The wet season, usually commencing in October and continuing to March or April, together with the melting of the snows during the early summer, produces a heavy run-off which diminishes considerably during the later s1.1,mmer months, with the result that storage is essential on practically every stream in order to regulate the flow to obtain a discharge which will meet the requirements of the load of the markets the power is to serve. Storage sites of sufficient capacity to equate the flows are not always present and it follows that, where such a deficiency exists, the difference must usually be met by burning fuel in steam plants. Fortunately, there are within the Province deposits of high-grade coal, suitable for the operation of such auxiliary steam plants. One of the strongest reasons for the development of water powers is the conservation of fuel. All use of coal or oil depletes resources that can never be renewed. Every water power developed means a saving in fuel and, even if at first it does not possess an over-powering financial advantage, it must become of ever increasing value as fuel resources become depleted. However, sight must not be lost of the inter-relation which should exist between the two methods of generating electrical energy, as each makes an admirable supplement to the? other with respect to suitability for carrying different types of load. In general, it can be said that the fixed charges of a water power development are usually high in relation to the operation costs, while those of fuel power plants are usually the reverse, so it is sometimes possible to combine the two methods of generation for the more efficient production of energy.

Jan 1, 1942

By Juliana Parreira

The past decade shows record increases in global demand for minerals and metals with an accompanying significant decline in skilled personnel. Mining companies today are examining new technologies to maximize production, reduce costs, and create safer work conditions to deal with this shortfall. Automation of an open-pit mine haulage system is receiving attention as a beneficial option since it provides more consistent and efficient operation of mining equipment, it removes workers from potential danger, it reduces fuel consumption significantly reducing greenhouse gas (GHG) emissions, and it can help optimize vehicle repairs and equipment replacement because of more-predictable and better-controlled maintenance. This paper describes a simulation model under development using the EXTENDSIM software package to examine scale-up issues and constraints of autonomous vehicles in comparison to a manual system. The software can predict and manage Key Performance Indicators (KPIs), such as productivity, safety, cost, equipment failures, fuel consumption, and tire wear under different road and load conditions. By breaking-down the various systems of an autonomous haulage truck and simulating the overall haulage system using a Monte Carlo approach, the model becomes a flexible and powerful tool to use within a mining organization. Direct comparison to a manuallyrun system can be done to show the cost and operational benefits of automation. Project managers can use this tool to guide decision-making about possible application of autonomous haulage trucks at a specific mine site.

May 1, 2010

By C. M. Anson

Introduction The prosperity of any country today is dependent upon the efficiency and growth of its primary steel industry. The ?march of the United States of America to its present commanding position in world affairs parallels the growth of its steel industry. The remarkable growth of that industry was possible only because bountiful providence endowed that country with adequate supplies of the raw materials necessary for steel making -coal and iron ore. If we accept this hypothesis, and surely we must, then to what extent can we envisage the future of our own country? This symposium deals with the most important of the raw materials required for steel making -iron ore. If we are blessed with a bountiful supply of iron ore, then surely a glorious future awaits only our taking advantage of that blessing. It is becoming increasingly evident that Canada has immense iron ore deposits. It is my privilege to make you acquainted with one of these, one that can only be classified as among the more important ore reserves in the world. I refer to the Wabana ore deposits in Newfoundland. Location These deposits lie under the floor? of Conception bay, off the east coast of Newfoundland. They consist of a series of beds which outcropped for a distance of about three miles on the northeastern shore of Bell Island, dipping at approximately 8° toward the northwest. This three-mile outcrop is the only key to the occurrence.

Jan 1, 1951

By Francis W. Gray

Introduction Extensive undersea coal-mining has developed on both the east and west coasts of Canada, and at this time some four million tons, or 25 per cent of the total output of Canadian coal, representing a pit-mouth value of $14,000,000 per annum, is coming from coal seams lying under the sea. Of the coal now being mined in Nova Scotia, 55 per cent comes from under the sea, and this proportion is likely to increase. The Province of Nova Scotia is at this date receiving in royalties paid upon coal ?removed from undersea areas a sum exceeding $400,000 per annum. The subject is, therefore, one of special interest to the Mining Society of Nova Scotia and the Canadian Institute of Mining & Metallurgy, and while this paper will deal chiefly with undersea coal-mining in Nova Scotia, an attempt has been made to summarize the development of mining practice in the winning of undersea coal in other parts of the world, with the hope that such a recital may assist in the assessment of local problems. The connection between the mining of coal under the sea and an insular or maritime geography is obvious in regard to Great Britain, Japan, Vancouver Island, Australia, and Cape Breton Island, and also in regard to the curious conformation of Chile; the tendency towards growth of a mercantile marine and naval eminence is equally obvious where coal is mined at tidewater. But, there is the further and less favourable significance that the mining of coal under the sea is associated with poverty rather than with abundance of coal reserves.

Jan 1, 1927

By D. Jean Hutchinson, Mark Diederichs

"Cable bolts are an important support component in modern underground mines. If an optimized cable bolt system is to be achieved, it is insufficient to focus on cable bolt layout design or on cable bolt installation in isolation. Cable bolt support, like all engineered systems, requires a holistic approach, encompassing integrated elements of design, implementation and verification. The “Cable bolting Cycle” described in this paper incorporates these components along with related tools and procedures which should be used together to ensure effective and efficient cable bolt support.Design involves the consideration of demand, capacity and constraints as outlined in this paper. The demands imposed on the sup-port system by the rock mass response to excavation under the combined action of stress and gravity must be matched to the capacity of the cable bolt array. The cable bolt system capacity is a function of the component strengths of the steel strand and the bond (load transfer) and by the deformation response and retention characteristics of the system. The design is bounded by operational and economic constraints.Implementation of the cable bolt array can then proceed and must include appropriate protocols of communication, training and quality control, in addition to both general and site specific installation procedures. Implementation will be discussed as the sum of these components.Implementation of the cable bolt array can then proceed and must include appropriate protocols of communication, training and quality control, in addition to both general and site specific installation procedures. Implementation will be discussed as the sum of these components.The information presented in this paper represents a very abbreviated version of much broader concepts, procedures and design charts, presented in a practical cable bolting handbook by Hutchinson and Diederichs (1996)."

Jan 1, 1996

By B. Tiryaki, M. Ayhan, O. Z. Hekimoglu

Coal shearers are one of the major sources of dust and fines in underground coal mines. Despite considerable research investigations, no comprehensive in situ investigations coupled with extensive laboratory studies on the effects of drum design on generation of dust and fines have been found. It may be for this reason that many major shearer drum manufacturers persistently employ a certain drum-lacing pattern on current coal shearers, which is believed to cause excessive dust and fines in coal mines. This paper shows how respirable dust and fines are minimized under near-identical conditions when the drum lacing pattern was changed from a triple-tracking to a single tracking arrangement. A series of laboratory trials simulating in full scale the practical cutting action of tools was followed by extensive long-term underground trials during production operations in OAL (Cayirhan) Lignite mine in Turkey. The results are presented and discussed, and recommendations for proper drum-lacing in terms of respirable dust and fines are made.

Jan 1, 2002

By Julie Dénommé

Today few in business would argue with the idea that we are living in a world that is Volatile, Uncertain, Complex, and Ambiguous. Coined VUCA by the US Army War College, these four words define the ?turbulence? and ?continuous white water? that the business literature has been documenting for the last decade. This VUCA world became even more relevant to business in 2007 when the Institute for the Future fellow Bob Johansen published the idea of transforming VUCA into Vision, Understanding, Clarity, and Agility. We call this VUCA Prime (VUCA'), and place an infinity loop (8) between them to show their dynamic interaction. This paper presents an exploration of the impact of VUCA 8 VUCA' on business and the conditions under which these dynamic forces help to successfully navigate change.

Oct 1, 2010

By A. R. House, G. W. Shepherd

Newmont USA Limited owns and operates the Phoenix Mine near Battle Mountain, Nevada, USA. The existing milling facility has operated since 2006 (House, 2010). Following the startup of the milling operation, and coupled with the upswing in the copper market, Newmont realized that Phoenix had no process option to treat transition and oxide copper ores. This meant that potentially revenue generating ore would be mined as waste. With no system in place to treat the transition and oxide copper, work began to determine the most feasible approach. After evaluating multiple options, the flow sheet was set for a runof- mine (ROM) heap leach pad and solvent extraction/ electrowinning plant (L-SX/EW). This paper will discuss the eight years of successes and challenges with developing the copper L-SX/EW plant and achieving commercial production of copper cathode.

Jan 1, 2014