Search Documents

By Andrew Kerr

Abstract - The base-metal and PGE contents of samples from magmatic sulfide mineralization are commonly correlated with their sulfide contents, indicating that the metal contents of bulk sulfides remain approximately constant within a given prospect or part thereof. Calculated sulfide metal contents provide valuable information in mineral exploration and research, but there are few formal descriptions and analyses of the procedures. Sulfide metal contents are best calculated using an assumed value (35.7% S) for a typical pyrrhotite-chalcopyrite-pentlandite mixture, and there appears to be little advantage in accounting for sulfide species separately. Regression of metal data against sulfur is probably the most rigorous approach, but is not always practical. Above 10% S, calculations are very robust, but lower sulfide contents generally demand at least some correction for non-sulfidehosted metals. Such corrections can become significant below 5% S, and/or in olivine-rich samples. They are best accomplished by mass-balance calculations, using concentration data from unmineralized host rocks. Significant uncertainties are introduced by analytical errors for sulfur, base-metals, and PGE, which are commonly measured from separate sample aliquots. These combined errors in sulfide metal contents generally exceed ±10%, but expand further at low S contents. In general, treatment of data from samples containing <2.5% S must be approached with caution, especially for PGE, for which the exact host minerals may not be known. Application of the method in simple grade-potential assessment is straightforward, but research studies involving sulfide-poor samples are inherently more complex. Under-correction or over-correction of data for non-sulfide-hosted metals can lead to false negative or positive correlations between sulfide metal contents and sulfide content. As the latter may itself be linked to geological parameters, such as depth within an intrusive body, undue significance could be ascribed to such trends. There are also valid geological reasons for such correlations, and such data require careful assessment to separate true and artificial variations. Propagated analytical uncertainties increase significantly in sulfide-poor samples, and must also be borne in mind whenever data from different localities or units are compared and contrasted.

Jan 1, 2001

By Nick Vayenas

This paper discusses the application of a commercially available state-of-the-art PC discrete-event simulation modeling software, called Promodel, for simulating a typical underground mine hoist system in the Sudbury mining region, in the province of Ontario in Canada. The reasons for using Promodel as a two-dimensional simulation development tool is its simplicity in use and its capabilities to provide enough flexibility to meet the modeling requirements of a mine hoist system. General information of a mine hoist system was collected for building the model. Example of the model?s output is also presented. The application of Promodel in underground mining offers a powerful, two-dimensional simulation environment in an affordable price for mining engineers to analyze and study operational problems. This hoist simulation model is an intuitive demonstration of the mine hoisting elements and the operational logic of the hoist, based on which optimization of the entire mine system materials flow can be considered as part of a mine cycle management feasibility study.

Oct 1, 2009

By John Shirokoff, Ladan Khaksar

"Cyclic polarization technique and also potentiodynamic measurements were applied to study corrosion behavior of 13% chromium steels in chloride containing environment. Potentiodynamic measurements were performed at 25 and 75 °C with 0, 10 and 20 g/l NaCl in 0.01 M hydrochloric acid solution. At the same time, the significant pitting parameters such as corrosion potential (Ecorr), pitting potential (Epit), protection potential (Epro) and passive current (Ipass) of cyclic polarization curves with various NaCl concentration were analyzed and compared to describe the corrosion behavior of 13% chromium stainless steel. Surface measurement techniques such as SEM and EDS were used for morphology and analysis of corrosion products. The results showed that both temperature and Cl- concentration had significant effects on corrosion behavior of 13% chromium stainless steel in acidic solution.INTRODUCTION Of all the corrosion resistant alloys (CRA) used in oil and gas developments, martensitic stainless steels (MSS) are some of the most common ones these days. These steels not only have the advantages of normal steels: high strength, cost-effective, easy to manufacture, available in a wide variety of product forms, but they also have good CO2 corrosion resistance at higher temperatures as a result of their 11% minimum chromium content. One of the most common types of MSS used in the oil and gas industry is 13% chromium steel. NACE and API standards both reference several different varieties of 13% chromium steels for use in oil and gas projects(“Corrosion Resistant High Cr Steel for Oil and Gas Wells,” 2013). All types of 13% chromium steels have about 12 to 14% chromium and other minor alloying additions, and can be placed into two general groups: conventional and modified. Conventional 13% Cr steels (13Cr) are those most common in oil and gas, some of which are CA6NM (UNS J91150), AISI 410(UNS S41000), and AISI 420 (UNS S42000). These alloys have excellent corrosion resistance when compared to carbon steels up to about 300°F (150°C) and are used for a variety of wellhead, tubular, and downhole components however they have very limited resistance to cracking in H2S (Vallourec Group, 2015). Modified 13% Cr (M13Cr) steels came from the need for increased corrosion resistance at higher temperatures, increased H2S cracking resistance, and increased yield strength above 85 ksi (586 Mpa) primarily for tubular goods and other downhole equipment. These features were developed by taking a conventional 13Cr steel and adding nickel (Ni), molybdenum (Mo), copper (Cu), and other alloying elements. M13Cr provides better corrosion resistance than 13Cr up to about 350°F (177°C), yield strengths up to 110 ksi (758 Mpa), and also improved H2S cracking resistance(“Corrosion Resistant High Cr Steel for Oil and Gas Wells,” 2013)."

Jan 1, 2017

By P. C. Thurston, T. Setterfield, D. H. Watkinson

"The Maybrun copper deposit IS In a succession of pillowed basaltic flows in the Wabigoon sub-province, northwestern Ontario. The rocks have primary flow morphologies and remarkably well-preserved crystallization textures, including quench-textured plagioclase, in spite of metamorphism to the amphibolite facies. The sulphide assemblage chalcopyrite-pyrrhotite-cubanite with minor sphalerite and pyrite is primarily in interpillow spaces and is stratabound. Basaltic rocks immediately enclosing the copper sulphide minerals have an enrichment in Fe, Mg and K and depletion in Ca and Na relative to surrounding flows. The Maybrun deposit is interpreted to have formed contemporaneously with volcanism and alteration, and was subsequently metamorphosed with the enclosing basalts.IntroductionThe association o f significant base metal accumulations with mafic submarine flows in the Archean is as yet poorly documented. Such deposits, where noted, have typically been small, and are therefore commonly over looked. The Maybrun Mine, a 2.6 x 106-tonne copper deposit in pillowed basalt, has many similarities with large, well-documented volcanogenic deposits. Given the interpretation of the Maybrun Mine to be volcanogenic in origin, there is n o reason why similar processes could not produce large deposit s. This is an important realization in an area where Archean submarine mafic rock s are very common, but frequently are examined only superficially. As gold commonly occurs in deposits such as Maybrun, even modest-sized deposits may be economic. The basalts at Maybrun are remarkable for amphibolite-facies rocks because of their extremely well-preserved delicate volcanic textures, including quench textures.The Maybrun Mine is one kilometre south of Atikwa Lake, in the Wabigoon sub-province of the Superior structural province, 75 km southeast of Kenora, northwestern Ontario, at longitude 93°35&apos;W, latitude 49°25&apos;N (Davies, 1973). Archean metavolcanic and metasedimentary rocks and intrusions underlie the area. Goodwin (1970) concluded that the mafic and minor felsic metavolcanic rocks, as well as the overlying metasedimentary rock s, were an eastward extension of the lower cycle of the Keewatin type section for the Lake of the Woods area. He estimated that the stratigraphic thickness of Keewatin rock s in this area is about 6900 m, of which 87% is basalt. The flows contain numerous interlayered sills, predominantly of basaltic composition; they have been extensively folded, faulted, metamorphosed to amphibolite facies and intruded by numerous felsic bodies, most importantly the Atikwa Batholith."

Jan 1, 1983

By W. T. Robson

Introduction Ground failure, violent or otherwise, is a problem to be contended with wherever underground operations are carried out. The character and extent of the failure, whether superficial or of more serious proportions, is determined by a number of factors, among which might be mentioned: the depth and dimensions of the underground workings; the types and distribution of wall rocks; structural features of the ore and enclosing rocks; the degree of metamorphism; the dip of the orebody; concentration of mining operations; the rate of mining; the history of the excavations made on the orebody in question. This last factor implies the consideration of such points as the arrangement and distribution of stoping both past and present, the current sequence of scoping, the type and effectiveness of the support used in old and current workings, and the amount and distribution of unmined parts of the lode. With such a variety of conditions, it is only natural that the situation at one place in a mine will not be the same as that obtaining in another part of the same mine and, more than likely, will be quite different in another property.

Jan 1, 1946

"These guidelines have been prepared to assist the Qualified Person(s)in the planning and supervision of exploration programs which will be reported under National Instrument 43101. The Companion Policy of NI43101 references the guidelines and states that issuers and Qualified Persons should follow them.Exploration Best Practices GuidelinesPreamble: These guidelines have been prepared to assist the Qualified Person(s) in the planning and supervision of exploration programs which will be reported under National Instrument 43-101. Such exploration programs must be under the supervision of the Qualified Person who will be responsible and accountable for the planning, execution and interpretation of all exploration activity as well as the implementation of quality assurance programs and reporting. These guidelines are also recommended for use in the planning and execution of exploration programs which will not be reported under NI 43-101. This set of broad guidelines or ""best practices"" has been drawn up to ensure a consistently high quality of work that will maintain public confidence and assist securities regulators. The guidelines are not intended to inhibit the original thinking or application of new approaches, that are fundamental to successful mineral exploration.Results should be summarized and reported in a Technical Report of good professional quality in accordance with the National Instrument 43-101 and Form 1 contained in that instrument. All exploration work from which public reporting will ensue must be designed and carried out under the supervision of a Qualified Person (""QP""). A QP is defined in National Instrument 43-101 as an individual who is an engineer or geoscientist with at least five (5) years' experience in mineral exploration, mine development, mine operation or project assessment, has experience relevant to the subject matter of the project or report and is a member in good standing of a recognized professional association."

Jan 1, 2003

By Zhiqing Zhang, Changyun Chen, Qing Liu, Lin Lin, Zhihong Jia, Guangjie Huang, Lipeng Ding

The effect of interrupted quenching (IQ) treatments on natural aging and bake hardening response of Al-Mg-Si alloy was investigated by hardness measurements, tensile test, differential scanning calorimetry (DSC) and transmission electron microscopy (TEM). The results show that interrupted quenching at 100oC could effectively suppress natural aging and improve bake hardening response. The optimized interrupted quenching treatment is 100oC for 45min, which gives the alloy a relatively low T4 temper strength and higher bake hardening response. The formation of highly dense cluster(2) during the interrupted quenching could be the reason for suppressing the natural aging and accelerating the precipitation of ß? phase during the paint bake treatment. In addition, interrupted quenching at higher temperature (170oC) results in unfavorable properties in both T4 temper and paint bake treatment. The formation of large precipitates is responsible for these undesired effects.

Jan 1, 2015

By Sunil Koppalkar, Liming Huang

"Since late 1980s the research group led by late Professor Andre Robert Laplante at McGill University undertook fundamental studies and applied research of the Knelson Concentrator (KC) and developed a sustainable method to correctly estimate gravity recoverable gold (GRG). In the early time a concept of ‘free gold’ was used, it was defined as the gold that could be separated and recovered from gold ore by amalgamation. Due to health and safety hazards, its practical use had declined. Around 1994, a methodology using a 3-in Knelson Concentrator to measure gravity recoverable gold was established at McGill University. Through more than 10 years’ improvement and optimization, this technique had become a standard method to evaluate GRG for gold ores, gold plant streams and platinum group metals. Until 2006, about 200 GRG tests had been carried out at McGill University for the ores from all over the world. Recently, a modified version of GRG test (short test) with the advantages of reduced processing time and lower cost had been developed for the mundane needs of gold industry.INTRODUCTIONGold gravity recovery has evolved significantly over the past twenty-five years, mainly because of the advent of the Knelson Concentrator (Knelson 1988, 1990, 1992, Laplante 2000). Now, a series of Knelson Concentrators for different applications are manufactured and used in gold industry all over the world (Knelson Concentrators 2004).In 1980s the Knelson Concentrator gained acceptance from mining industry as an effective device for the recovery of gold from grinding circuit. Knelson Concentrator became the obvious choice because of its design features: a relatively long processing time without concentrate discharge (compared to some other centrifuges, such as Falcon Concentrator and Chinese Yunxi Centrifuge at that time), large throughput capacity, treating a wide size range of material, yielding a high grade concentrate with small mass that could easily be smelted. As more and more Knelson Concentrators were accepted in gold industry, mineral processing engineers faced with challenges: what are the separation mechanisms of the Knelson Concentrator? How much gold can be extracted for an ore if a Knelson Concentrator is installed? For answering these questions, a laboratory scale Knelson Concentrator was created."

Jan 1, 2007

By J. A. Allan

"The history of the development and application of controlled recirculation systems in U.K. collieries is traced and the theory behind such systems briefly examined. Specific applications for dealing with dust and dust/heat problems in headings, for which practical experience is currently available, are described. Consideration is given to the special features which these systems introduce in the underground situation and to the essential safeguards which are required for their safe use.IntroductionRecirculation of air is a commonly used technique in genera l ventilation and air conditioning practice, but has always been regarded with some suspicion for mining applications. This is perfectly understandable in view o f the hazardous conditions which can occur with dangerous forms of recirculation in mines. However, certain controlled recirculation techniques can offer advantages, particularly in the field s of dust and climate control in headings, provided that they are designed, Installed an d managed with full comprehension o f all aspects of the system and always bearing in mind that from the point of view of serious firedamp ignition risk, headings are potentially the most hazardous places in coal mines.BackgroundProbably the first recorded use of deliberate recirculation in British collieries was reported by Lawton in 1933. This researcher described trials, undertaken under the auspices of a national committee on ""The Control of Atmospheric Conditions in Hot and Deep Mines"", involving attempts to increase the velocity, and thereby the cooling power on hot faces, by means of simple recirculation systems using fans and ducts delivering recirculated air in the opposite direction to the normal face airflow. No significant cooling advantage was obtained and there is no subsequent record of this work being continued. During the discussion on this paper, there was considerable disbelief that fire damp percentages had not increased significantly when air was recirculated, but apparently no attempt was made to establish why this should be. It is of interest to note that J. Ivon Graham, one of the contributors, recommended that recirculation should be tried in stone headings for the control o f dust, as he believed that ""there may be scope for recirculation and filtration of the air under certain circumstances in such headings"". This idea was not developed for another forty years."

Jan 1, 1983

By J. K. Afidenyo, J. Osei-Owusu

"The Obuasi Mine of AngloGold Ashanti Limited has been operating the world’s largest Biooxidation Plant at its Sulfide Treatment Plant (STP) in Ghana, using the Gencor Biox® technology since February 1994. The Biox® technology was preferred to other alternative methods of treating refractory sulfide ores such as roasting, pressure oxidation and nitric acid leaching due to among other reasons, its lower capital and operating costs, reduced technical risk, relatively benign environmental impact and its ease of operation and maintenance in a remote location.STP has since commissioning succeeded in operating this technology successfully but not without some operational problems. The Plant has seen a number of upgrades and modifications in its circuits which were motivated by cost, operational and throughput constraints.The objective of this paper is therefore to highlight the mine’s experience in the treatment of its complex carbonaceous refractory sulfide gold ores with emphasis on plant operations and improvements such as the Biox® reactors expansion, flotation concentrate upgrade project and neutralization circuit modifications. The Biox® Plant operating cost is also discussed.INTRODUCTIONThe Obuasi mine forms part of the AngloGold Ashanti Group of Gold Mines. It is located in the Adansi West District of the Republic of Ghana. The mine is primarily an underground operation, although some surface mining still takes place. Ore is processed by two main treatment plants: the Sulfide Treatment Plant (for underground ore) and the Tailings plant (for tailings reclamation operations). A third plant, the Oxide Plant, is used to batch-treat remnant opencast ore and stockpiles, of which there are adequate tonnages to keep the plant operational until 2008.Though reference is made in this paper to the Tailings and Oxide Treatment Plants, the main focus will be on the Sulfide Treatment Plant."

Jan 1, 2008

By C. Y. Lim, H. W. Kim, M. S. Kim, J. H. Cho, Y. S. Lee

Al - 5.5 wt% Mg - 0.3 wt% Cu alloy strip was successfully fabricated by horizontal-type twinroll casting (TRC). For producing sound strips with no surface defect, the casting was conducted at various roll rotation speed, and the sound strip could be obtained at relatively low casting speed (3 rpm). The cast strip was homogenized at 450 °C for 10 hours, and then cold rolled with a reduction rate of 78%, followed by a final annealing at 450 °C for 1 hour. The annealed sheets showed good mechanical properties with approximately 330 MPa in tensile strength and 27 % in elongation, but exhibited strong anisotropy depending on the tensile directions. For the homogenized sheets, warm rolling was also conducted at 200, 300, and 400 °C. The tensile test results of the warm-rolled sheets showed that the rolling at medium temperature (300 °C) was proper to fabricate the sheets with relatively good mechanical properties and low anisotropy.

Jan 1, 2014

By J. C. Nicholson

The "V" system was first introduced by the West Virginia Coal & Coke Company at their No. 9 mine, Norton. Norton is a small mining village on the B. & 0. railway, about seven miles from the town of Elkins. This year, accompanied by G. D. MacDougall, I visited this mine to obtain first-hand information regarding this modem system and to determine its adaptability to conditions in Nova Scotia. The following is a brief account of my observations. The seam that is being worked is known as the Lower Kittaning, which, at this point, has an average thickness of 7 feet. This includes a band of hard clay varying in thickness from 8 to 14 inches, which occurs about 2 feet from the pavement, also 8 inches of inferior coal at the roof. The latter is not recovered, which leaves to be mined about 5 1/2 feet of clean coal. The roof is slate and shale for the first 30 feet, followed by 40 to 60 feet of sandstone; the total cover is from 80 to 250 feet thick. The seam lies very flat, with a dip of only 2 per cent., and, as the dip is toward the main entrance, it&apos; is in favor of the load, also providing natural drainage for any water the mine makes. As the mine is not gassy, and there is no water to be pumped out, one can understand that mining conditions are practically ideal.

Jan 1, 1924

By Fidelis T. Suorineni

Rockbursts are a major hazard in deep hard rock underground mining and tunneling. To date a significant number of rockbursts still defy conventional explanations. A review of rockburst case histories in the literature has shown that pillars and tabular excavations under shear loading are prone to rockbursting in situations where they are least expected under conventional knowledge of rockburst causes. Despite the evidence of the effects of shear loading on underground infrastructure, and the frequency of their occurrence, little is known about how this loading mechanism causes such large magnitude events and extensive damage. In this paper analytical and numerical modeling are used to understand the behaviour of pillars and tabular excavations under shear loading. The numerical modelling results show that pillars under shear loading are less confined than their equivalents in loaded in pure compression in the same geologic environment, and are therefore more brittle and weak. For tabular excavations under shear loading, the behaviour depends on whether such excavations are continuous, co-planar or offset with rock bridges. Analytical results based on slit theory show releasable potential energy in tabular excavations increases nonlinearly with excavation half-span. The study results are important for the safe and economic extraction of orebodies under shear loading.

May 1, 2011

By S. S. Yuan, Q. Z. Zhu, J. F. Shao

"This paper aims at enriching a homogenization-based anisotropic damage model for hard rocks under complex loading. A new damage criterion is proposed to capture material strain softening. Within the framework of irreversible thermodynamics, we are particularly concerned with two strongly coupled dissipative mechanisms: frictional sliding and damage by microcracking, which usually take place at cracks within cohesive geomaterials under compression. Focusing on the representative elementary volume containing multiple crack families, the free enthalpy of the matrix-cracks system is obtained. Importantly, a back-stress term is involved in the local stress applied to microcracks. This back stress plays the hardening/softening role in the friction criterion which is formulated at local scale. Strain hardening owns to the accumulation of frictional shearing and dilatancy while strain softening is caused by crack growth. The multiscale damage model is used to simulate laboratory tests on the Westerly granite under true triaxial compressions. INTRODUCTIONWhen subjected to compressive loads, hard rocks present nonlinear mechanical behaviors and induced material anisotropies. In that process, two main dissipative mechanisms have been largely identified: damage by crack growth and frictional sliding along closed crack faces, which are usually strongly coupled to each other on crack scale. Theoretical investigations have shown that the damagefriction coupling analyses allow explaining a large number of experimental phenomena involved in brittle or quasi-brittle materials. Concerning constitutive modeling, the standard Eshelby’s solution-based homogenization procedure for heterogeneous materials was recently applied successfully to describing the mechanical and poromechanical behaviors of cracked frictional solids."

Jan 1, 2015

By Brian Flintoff

"When I was first asked to prepare this paper and presentation in late June, I thought it might be fun to ""step back and paint the bigger picture."" Having attempted to do this, fun is not the first descriptor that now comes to mind, and speaking dyslexically, I've had 'nuf.'Unlike Nostradamus, or even Orwell, I've discovered that I'm ""clairvoyantly challenged"" and not even the psychic hot-line was of much help, at least with respect to process control! I am somewhat comfortable speculating on evolutionary change, but the radical developments that will arise from revolutionary changes are well beyond my mortal capabilities. Even with evolutionary change, I'm reminded of the lessons of time series analysis which show the prediction error to grow exponentially as the horizon moves into the future. As Macluhan is reported to have said: ""Predicting the future based on the past is a little like driving your car while looking in the rearview mirror!""Having honestly presented my qualifications, allow me to try to look at process control and to offer some conjecture on where we're probably headed. In the end, it is said that: ""The plant of the future will have only two employees, a man and a dog. The dog will be there to keep the man from touching the equipment.1""IntroductionA little less than a decade ago Andy Mular and I co-edited a monograph entitled ""A Practical Guide to Process Control in the Minerals Industry."" The work was commissioned by the senior management of a consortium of Canadian mining companies, since it was widely perceived that control was an area of great economic potential, but one that had not been effectively tapped. The concern was that if the industry could not soon deliver on the ""potential"", the term may well have appeared in the epitaph of what was, to these men, a very attractive investment opportunity. I think it is fair to say that over the past few years process control has clearly established itself as an essential technology in plant operation and optimization. That isn't to say that we get it all-right, all-the-time, but, the circumstances are much different than they were. In the eyes of many, process control has attained the distinction of being considered a mature technology, even though there are still countless avenues for exploration."

Jan 1, 1998

By Janis A. Shandro

The mining sector is a major economic driver for Canadian, and British Columbian communities. In parallel strong commitments have been made by industry to the well-being and sustainability of associated communities. However, these dimensions are the least understood. Especially lacking are focused regional investigations that compare the well-being and sustainability of communities dependent on different resources sectors. It is hypothesized that this type of comparative analysis will help to foster a greater understanding of what makes a resource or mining community healthy and sustainable. This paper describes research that examined community-level indicators associated with well-being (e.g. education, income and employment) and sustainability (e.g. economic diversity). The indicators were derived from Canadian Census data for 31 British Columbia resource-based communities (with a focus on mining) during a period of time (1991 to 2001) when resource sectors experienced an economic downturn. Our findings identify that during this decade, mining communities differed significantly from other resource-based communities, and comparative analysis of census derived indictors illuminate challenges that mining communities in British Columbia face with respect to wellbeing and sustainability (such as economic diversity, unemployment, and population loss). To contribute to the mining sector?s efforts towards meeting their commitments to communities, this paper concludes by proposing strategic opportunities aimed at the enhancement of mining community sustainability for policy-makers, communities, and the mining industry to consider.

May 1, 2011

By T. Senga, T. Namihira, S. Terada, S. Owada

"Electrical disintegration (ED) has been well known as a good comminution method to improve liberation of compositional phases because it was reported that electron avalanche could occur preferentially at phase boundary. But the detailed mechanism of the ED has been still not known. This paper describes the results of ED experiments using synthetic binary sample, copper/resin, under the conditions of various distance between electrodes, and discusses the energy distribution in the three kinds of phenomena in the ED process, which are(1) streamer progression in water, (2) electron avalanche in water, and (3) electron avalanche in solid sample, by measuring current and voltage with elapsed time. Then, it has been found that the energy distribution in the phenomenon (1) is quite low and that the distribution in the phenomenon(2) had a considerably large compared with that in the(3), which indicates that the shockwave generated in water could contribute much to the sample breakage.INTRODUCTIONElectrical disintegration (ED) has been well known as a specific comminution technology which enhanced selective breakage at phase boundary and lead to a good liberation among compositional phases1-6),but the detailed mechanism has not been clarified yet. This study describes energy distribution among the phenomena in the ED process by using a synthetic binary sample, copper/resin, the phenomena of which are (1) streamer progression in water, (2) electron avalanche and shockwave generation in water and (3) electron avalanche in solid sample usually at phase boundary. The energy distribution could be calculated from ED experiments and from voltage-current changes between electrodes as a function of elapsed time.SAMPLE AND EXPERIMENTALSampleThe sample used in this paper was a synthetic binary solid of copper/resin as shown in Figure1.Cut and polished pure copper lump was put into silicone mold and melted epoxy resin was poured into it and cooled, then, finally the binary sample was polished and molded in the form of 10 mm * 10 mm * 10 mm."

Jan 1, 2017

"Polycom, a new approach to ore processing based on pressure comminution, is obviously a very attractive alternative to conventional processing methods.Since a full-scale pilot plant was commissioned in 1986, more than 125 commercial installations, with capacities up to 1000 t/hr, have gone ahead.Already successfully used in processing cement clinker, limestone, coal, and other minerals, Polycom high pressure grinding results in:o Significantly reduced capital costs, because smaller units can be used m new installations;o Capacity increases of up to 100% in existing facilities; and o Operating economies that include energy savings of 20% or more, and reduced wear parts consumption.1. IntroductionAutogenous or semi-autogenous mills in conjunction with rod or ball mills are used with preference for ore processing. Most ball mills are of closed-circuit design and operate with mechanical classifiers (spiral or rake classifiers) or hydrocyclones. In other words, the ores undergo wet primary grinding, since slurries are required for the downstream separation stages anyway. This paper presents a new grinding system based on high pressure comminution of ores. This grinding process allows:- Energy savings of up to 20 % or more- Capacity increases of up to 100 % and more- Reduction of wear costs- Smaller units for new installation and thus- Reduced investment costsThese advantages are highly interesting for both new installations and conversion projects, particulary in cases where an increasing hardeness of the ore, i.e. rising Bond Work Index, reduces the output of the plants or where the metal assay of the ore decreases and the capacity of the existing systems has to be increased. POLYCOM high-pressure grinding rolls have established themselves with great success already for grinding cement clinker, granulated blast furnace slag, limestone, cement raw materials, coal and other materials.Meanwhile more than 250 high pressure grinding rolls have been installed worldwide. Capacities up to 1.000 t/h with roller diameter up to 2.8 m and drive units up to 2.400 kW are installed."

Jan 1, 1991

By Ken Wood

"A reliable source of water of an acceptable quality is vital to the success of any mineral processing plant using wet methods. For Cerro Verde, a new 108,000 t/d copper mill in southern Peru, the main source of raw water is the Chili River. The Chili River is heavily contaminated with raw sewage, industrial wastewater and agricultural runoff, and can also receive high sediment loads during the rainy season. The initial water treatment plant could not supply design flows of water due to the exceptionally poor water quality. Problems with treated water quality caused significant difficulties with water consuming equipment, such as the plant cooling systems. This paper details the Cerro Verde water system and changes from design through to start up from a mineral processing perspective.INTRODUCTIONMining, and mineral processing in particular, is a water intensive activity. Improving water system design and practice are key strategic requirements in moving toward a more sustainable mining industry. This case study forms a basis for ongoing research into water use and reuse at mines and mineral process plants, conducted by AJ Gunson, under the supervision of Dr. Bern Klein and Dr. Marcello Veiga at the University of British Columbia. The case study material was gathered through involvement with the design, startup, and redesign of the Cerro Verde water system.Cerro Verde is a low-grade copper porphyry mine, located near the city of Arequipa in southern Peru, at an elevation approaching 2,800 m. In 1972, one of the world’s first copper Solvent Extraction – Electrowinning (SX/EW) facilities was built on the site, processing oxide ore from two main open pits. In 2004, the operator, Sociedad Minera Cerro Verde S.A.A. (SMCV), approved a 108,000 t/d expansion project to process sulfide ore reserves through a new concentrator plant. The plant was designed under extremely tight schedule and capital constraints, with a mandate to intentionally avoid any overdesign."

Jan 1, 2008

By M. Redfearn

"DUST COLLECTION EQUIPMENT LIST Primary Dust CollectorModular Mikro-Pulsaire - Model 2G1-96TR Capacity: 20,000 c.f.m.Bags: Total of 288; 8' x 4 1/2"" diameterMaterial: Dacron HCE feltAir to cloth ratio: 7.55/1Bags are changed every 6-9 months. Sent to A & L Services for cleaning at a cost of less than 1/3 the price of a new bag. No new bags have been required since start-up 4 years ago.Blow hack: 35 c.f.m. at 100 p.s.i.Fan: Joy Manufacturing, Model 3300, Type 4S, Backward inclined fan.Impeller: 33"" diameter36"" diameter Inlet33"" diameter Outlet at 3200 f.p.m. velocity1945Motor:,60 H.P., 1780 r.p.m.Capacity: 23,400 c.f.m.Design:,20,000 c.f.m.,•Actual:,17,500-19,000 c.f.m. depending on bag condition.Dust Slurry Agitator: Port-a-flo Model 050-350Major Maintenance:The fan was sped up from 1830 to 1945 r.p.m. and balanced at the higher speed. Several months later the impeller destructed beyond repair. A new shaft and impeller was installed, casings straightened, and bearings reused. Unit is currently running at 1945 r.p.m. No definite cause for the impeller failure has been found, although it might be attributed to improper balancing."

Jan 1, 1976