Search Documents

By Peter N. Blakey, Jean-Paul Paquette, Barton A. Thomson

"FROM THE BEGINNING OF THE PIT, it was known that the surface mining method had a projected life of about ten years, and that the ore extended to depths recoverable only by underground mining. When serious consideration was given to underground mining in 1968, it was realized that tremendous advantages could be gained by starting the underground mine as early as• poss1ble. These included: 1. The availability of underground ore for grade control, which would become more difficult as the pit deepened. 2. The need to develop new systems, equipment and skills to take full advantage of the technological revolution in underground mining. 3. Early knowledge of rock behaviour through trial mining on a small scale prior to finalizing plans for major blocks. In addition, the pit would be available to guarantee the mill supply if problems were encountered. 4. With sufficient time and early mining experience a much better job could be done on all mine planning. Because ample reserves of economic underground ore were virtually assured, the desired underground mining capability became a function of two restraints: first, the time required to excavate and construct the permanent headframe, shaft and ore-handling facilities necessary to handle large volumes of stope ore; second, the time for lateral and stope development on at least one level which would normally follow shaft sinking. The decision made was to move immediately on the permanent hoisting installations and at the same time embark on the planned ramp from surface, which would allow much stope preparation to be completed prior to .bringing the shaft on stream. Both projects were placed on an urgent basis early in 196S' and the following decisions made shortly thereafter."

Jan 1, 1974

By M. Hozayen, E. S. Radwan, P. A. Nawrocki, A. Jebbouri

"A major geomechanical study was conducted for one of the UAE onshore oil fields with the purpose of studying reservoir rock properties and stress distribution, based on which a 3D coupled reservoir geomechanical model was built. This model was later used for wellbore stability analysis and for analyzing the effect of fractures on future reservoir production performance, including fracture deformation and permeability evolution occurring due to reservoir depletion and resulting changes in local stress field. The subject of this study was a complex fractured Upper Cretaceous carbonate reservoir characterized by high degree of heterogeneity, both vertically and laterally. Wellbore instability related drilling problems were encountered while drilling the wells in this field. The problems were mainly in drilling the horizontal wells, including breakouts and mud losses. Experimental results of laboratory tests are summarized in this paper whereas wellbore stability analysis and formulation of a 3D geomechanical model that was built for that purpose is summarized in a sister paper (Part II).A suite of tests reported includes tensile strength, uniaxial and triaxial compression and permeability under stress at simulated reservoir conditions. All tested rocks have been grouped into twelve test units and reservoir geology, rock types and challenges related to designing a viable sampling and testing program for a big reservoir are discussed first followed by sample selection criteria and details of the testing program. All test units showed brittle behavior at zero confinement and some samples showed similar behavior at low confining stresses. With confining stress increase, the behavior gradually turned to plastic but some samples showed features of ductile behavior even at low confinement.Obtained experimental data have been summarized in the form of strength criteria and correlations. The Mohr-Coulomb strength equations were obtained for each test unit and also for the averaged values. It was noticed that triaxial compressive strength (TCS) increases with decreasing porosity or increasing density but their influence on TCS is getting smaller with confining pressure increase. Good correlation of porosity and density with Young’s modulus, Poisson’s ratio, unconfined compressive strength (UCS), friction angle, cohesion and tensile strength has been noticed and there was an increasing trend between the confining pressure and TCS. Rock type (mud or grain supported) was not influencing the TCS as much as porosity and density and the two lithologies encountered affected TCS approximately in the same way. These results and correlations are summarized and explained in this paper. They were further used in the numerical modelling part (Part II) of this paper, Hozayen et al. (2015). It is also concluded that rock lithology is not a decisive factor and mechanical properties of tested rocks should be rather considered dependent on porosity and permeability. This helped greatly in reducing the number of tests that had to be performed."

Jan 1, 2015

By F. Logsch, H. Pempel, J. Markowski, P. Ay

"Due to the European Directive 2000/53/EC on end-of-life-vehicles, from 2015 on more than 95% of car materials have to be recycled. In order to recycle the materials back into the economic cycle, it is necessary to produce products with high quality and purity.Plastic components in cars, which are coated with metals by vapour deposition or electroplating, have a wide circulation (e.g., as cladding panel or trim strip for interiors and exteriors). In the end-of-lifevehicle recycling process, these plastic-metal composites are not considered in usual technologies (car shredder) and are not separated from Automotive Shredder Residue. These parts can be separated by optical or HF-detection sorting and then introduced to a specific treatment.Experiments with a specially developed bioleaching configuration showed that the thin coatings, which consist mainly of copper, nickel and chromium, can be removed efficiently from the polymer base materials by a bioleaching solution with Acidothiobacillus ferrooxidans as a leaching agent. The solution used was produced in special fermenters with a 9K-nutrient salt media. During the bioleaching process at 35°C maximum temperature, most of the copper is dissolved and the other metals accumulate as metal sludge. The bacterial cultures based on A. ferrooxidans are robust and resilient.After a 48-hour bioleaching period while the composites were stirred regularly with ventilation, the plastic particles were completely free from metallic coatings. The metal components are separated for further use: undissolved components (mainly Ni and Cr) are separated by decantation of the solution; dissolved copper recovey is carried out by cementation of copper. The cementated solid contains ~98% Cu, along with small amounts of other metals.With the bioleaching process, good separation and re-utilization of the metallic coatings is possible. The cleaned plastic parts were prepared by compounding for new applications with injectionmoulding."

Jan 1, 2016

By Jean Vavrek

What is CIM?s role on a planet-wide scale? That question has been coming back to the forefront of many discussions regularly in the months since we came on board as Executive Director and Vice-President International. CIM, by its name and by the nature of its history and make up, has mainly been a Canadian entity. It has been created by an act of Canadian Parliament and it is set up to work within the Canadian federal and provincial framework.

Feb 1, 2004

By W. McCombe, G. Remple, L. Nightingale-Mercer

The McClean Lake Mill is located approximately 850 kilometres north of Saskatoon, Saskatchewan, Canada, and is operated by Orano Canada Inc. (Orano). The mill was designed to process high grade uranium ores, and a multi-year expansion was completed in 2014 to increase its production capacity to 24 Mlbs U3O8 per annum. The mill also underwent various upgrades to allow it to safely transition from processing low grade ores to high grade ores from the nearby Cigar Lake Mine. During the metallurgical test work on the Cigar Lake ores, it was identified that some ore zones of the deposit have a propensity to generate hydrogen gas during acid leaching. Hydrogen is a volatile and explosive gas, which poses obvious safety concerns in the leaching circuit. Uranium processing is further complicated by the fact that an oxidant in the form of oxygen gas or hydrogen peroxide is required to regenerate iron in the leach, which further increases the risk posed by hydrogen gas. During 2013 Orano and its consultant Hatch designed and engineered several novel upgrades to the leaching circuit to mitigate the risk of hydrogen gas evolution in the process. Best in class technology was utilized in addition to control and operating strategy changes to ensure the leaching circuit could be safely operated with ores that evolve hydrogen gas. This paper reviews the design concepts and modifications implemented on this unique and challenging project, and also provides an update on the operational reality of hydrogen in the circuit gained through five years of operational experience with hydrogen evolving ores.

Jan 1, 2020

By M. L. Connolly

Zinc production by Cominco Ltd. began in Trail in 1916 at a rate of 55 metric tonnes per day (t/d) and was increased ,in several increments until now electrowinning capacity approaches 750 t/d. The last increment, 40-t/d high-productivity electrowinning plant, was commissioned in 1974. In this paper, the design and operating experience with both the existing electrowinning plant and the new high-productivity plant are described.

Jan 1, 1977

By Darryel Boucher, Thomas W. Leadbeater, Raymond Langlois, Joshua Sovechles, McGill University, Zhoutong Deng

"Spiral concentrators are used to upgrade ore based on the density difference between their component minerals. This simple flowing film gravity separator is of interest for the processing of large amounts of material, as found in the iron ore industry. Addition of wash water at different points on the trough of the spiral affects the grade and recovery of the valuable concentrate by affecting the flow of particles within the thin slurry film. This paper shows how radiolabelled hematite (-355+300 µm) and quartz (–1,180+1,000 µm) tracers were used to determine the particles’ behaviour within the slurry film with and without the addition of wash water. The results presented provide a detailed particle flow pattern around a wash water addition point and its effect on the trajectory and velocity of the particles. This information is of interest in building knowledge about spiral wash water injection parameters such as injection location, direction, flow rate and nozzle orifice type (affecting jet shape and velocity).INTRODUCTIONSpiral concentrators are density based separation devices. They are extensively used in the upgrading of iron ore, fine coal and minerals sands (sources of ilmenite, rutile, zircon and monazite) (Wills & Finch, 2016). A spiral unit is composed of a channel of specific profile formed as a helix of 3 to 7 turns around a central structural post. The feed pulp is composed of 15 to 45% solids with particle size from 75 µm to 3000 µm (Wills & Finch, 2016). Throughput of a single spiraling trough can be up to 8 ton per hour and multiple trough unit (up to four trough) can process up to 30 ton per hour for a footprint of around 0.7 m2 (Palmers & Vadeikis, 2010). They are low cost concentrators considering manufacturing of their trough via polymer reverse molding. The energy intensity of a spiral plan is notably small considering the throughput and is mostly related to pulp pumping and final concentrate dewatering."

Jan 1, 2016

By William Pitman

Ground instability and subsequent rock falls are a major concern in underground mines. As a result, several mining companies are conducting risk assessments of the ground support installed in their mines. Risk assessment is now commonly used to provide mine operators with a systematic process to assess the strategic risks that could lead to injury to personnel or loss of production, and evaluate possible risk control measures. Risk assessments can be carried out to identify major hazards, assess the likelihood of occurrence and consequences of each hazard and estimate the level of risk. This process allows assessment of possible remediation actions to minimize the risk and likelihood of occurrence or mitigation of the consequences to a level that is reasonable and practical. This paper presents two practical mine applications of qualitative risk assessment of ground support to highlight the benefits of this process. Yearly or bi-yearly risk assessment of mine excavations can assist mine operators in prioritizing resources and areas that require support remediation. In addition, it provides a mechanism for proactive response to reduce potential risks associated with personnel safety, equipment safety and environmental impact. It also provides a baseline against which changes in ground condition can be compared and quantified.

May 1, 2004

By A. B. C. Stothart

"IntroductionIn the past four years Ontario Mines have made great progress in the development of reliable mine conveyance safety dogs. History shows that, prior to 1945, a rope failure on a descending conveyance was usually followed by unsatisfactory safety dog operation.It is proposed in this paper to discuss briefly;The history of this development. Progressive .development of one type (E. Long).Free fall testing of safety dogs. Anti-trailing rope device.HistoryOn February 2nd., 1945, a hoisting rope broke at the Paymaster mine. The safety dogs proved ineffective and permitted the cage to crash through to the bottom of the shaft, with disastrous results.Following this accident, the Ontario Government appointed a Technical Committee to investigate The Safety of Hoisting Equipment and Hoisting Practice in Ontario Mines. This Committee consisted of Dr. C. R. Young (Chairman) and Professors T. R. Loudon, E. A. Allcut, V. G. Smith, and Lloyd M. Pidgeon. The Ontario Mining Association (at the request of the Ontario Government) also appointed a Committee consisting of Messrs. R. E. Dye, R. D. Parker, and R. L. Healy."

Jan 1, 1950

CORPORATE SOCIAL RESPONSIBILITY CSR is about how companies manage the business processes to produce an overall positive impact on society. - Indentured work, sexual slavery, fair trade, organic growing, business ethics, environmental issues, ?Right to know -Right to decide?, AIDS activism, civil society - Balancing stakeholder issues - Government responses Who are the bad guys? Where are the threats?

May 1, 2010

By Jochen Petersen, Alison Lewis, Cledwyn Mangunda

Run-off and waste water streams high in dissolved metal content are generated in all mining operations. The metals pose a threat to life due to their persistent bio-accumulative toxic (PBT) characteristics. Hence, there is a need to treat mine waste water effectively. Lime precipitation is the technology of choice through which Fe, as the major metal species, is removed as Fe (III) oxyhydroxides with other metals co-precipitated and/or adsorbed. Sulphates are removed as gypsum or incorporated into the Fe phases. The resulting sludge has poor dewatering characteristics and is deposited in landfills, with an inherent risk of returning the Fe back into the water cycle through leaching. This study seeks to understand the mechanisms behind the formation of this sludge in terms of product quality. The relationship between process conditions and product characteristics has been investigated through exploring the effect of Fe (III) concentration on the precipitate product characteristics (particle size distribution (PSD), size, morphology and structure) and quality (in terms of filterability, settling ability, etc.) in a simplified system. Neutralisation of acidic synthetic aqueous Fe (III) sulphate streams containing 50, 400 and 800 mg/L Fe(III), respectively, was effected by mixing it in a continuous stirred tank reactor (CSTR) with dissolved calcium hydroxide for pH control at a residence time of 15 minutes. Precipitate samples analysed for morphology and PSD, using nanoSEM and Zetasizer respectively, showed a general decrease in PSD and zeta potential with increases in feed Fe (III) concentration. These results were used to infer the particle size enlargement mechanisms of Fe (III) oxyhydroxide precipitates under a given set of operating conditions. Preliminary product quality results indicate that a high concentration (800 mg/L) leads to the rapid formation of metastable precursors with poor product quality, whilst a low concentration (50 mg/L) leads to formation of thermodynamically more stable precipitates with good product quality. The approach demonstrates a potential route forward in terms of linking operating conditions to the attainment of desirable characteristics rather than specific precipitate phases which are difficult to identify.

Jan 1, 2016

By W. R. Tyson

Pipelines for the transport of gas and oil are being designed to operate at increasing pressures in increasingly harsh environments. The steel used to construct these pipelines must have adequate toughness to tolerate weld imperfections (i.e. withstand bending strains) and to arrest running cracks (i.e. to prevent propagation of axial fractures). The problems posed in specifying suitable toughness parameters and the approaches currently being used to measure them are discussed.

Jan 1, 2005

By Ross G. Bertinshaw

"The Line Creek Mine of Crows Nest Resources started mining coal in the fall of 1981. There are seven mineable seams with thicknesses ranging from 1.5 to 13 metres and with dips varying from 0 degrees to 60 degrees. This, together with internal partings and the very friable nature of the coal, creates a number of mining problems.The coal is divided into zones depending on the dip of the seam. Each zone requires a different mining technique to ensure optimum recovery and low dilution while still keeping fines to a minimum.Line Creek employs a combination of hydraulic front shovels and backhoes to mine its coal without blasting or use of dozers. This has been very successful in reducing the proportion of fine coal hauled to the plant, thus improving quality control and reducing costs in coal processing.There have been a number of other benefits from the use of excavators instead of more conventional methods. These include better selectivity, good cleanup, reduction in traffic at the face and lower cost.IntroductionThe Line Creek Mine is situated approximately 25 km north of Sparwood in southeastern British Columbia (Fig. I). Preproduction stripping began in J98J with the first coal shipments made in 1982. In 1983 the mine produced 2.1 million tonnes of raw coal.Similar to other East Kootenay coals, the seams at Line Creek are characterized by their friability, producing a large proportion of fine coal during mining. In an attempt to reduce these fines Crows Nest Resources has instituted the use of hydraulic excavators to mine and load the coal.Hydraulic excavators offer other substantial advantages over front-end loaders and dozers, which has been the conventional system in other mines in the area."

Jan 1, 1985

By C. S. Chen, Y. J. Luo, M. W. Gao, B. Li, Z. F. Zhang

"To obtain large-sized billets with fine grains and homogeneous elements distribution, uniform direct chill (UDC) casting process, based on annular electromagnetic stirring coupling with intercooling, was employed to produce 7055 alloy billets with a size of F584 mm in this study. The results indicated that there were the coupled effects of annular electromagnetic stirring and intercooling on grain refinement and element homogenization, and also the billets produced by the UDC casting process showed excellent hot workability in comparison to the normal direct chill casting process.INTRODUCTION The high solute 7055 aluminium alloy has a wonderful combination of high specific strength and hardness, good resistance to stress corrosion cracking and high fracture toughness, which is very useful in aerospace application (Yan et al., 2013; Mondal & Mukhopadhyay, 2005). The production of large-sized 7055 alloy billets with high quality is the basic condition for the subsequent application of 7055 alloy to the aircraft. Inhomogeneous microstructures and performances of 7055 billets result from the high alloying element content and the inhomogeneous cooling condition in different regions of billets during the conventional direct chill casting (Paramatmuni et al., 2004; Lalpoor et al., 2011), which will bring bad influence to processing property, functional performance and utilization rate of materials. To alleviate segregation and obtain fine and uniform grains, some effective treatment methods were proposed including electromagnetic stirring (EMS) (Vives, 1989), ultrasonic vibrating (Zhang et al., 2011) and melt conditioning (Fan et al., 2013), on the melt to obtain fine and uniform grains. However, these methods could not effectively decrease the large temperature difference between central and periphery parts of the billet, because the solidification mainly depends on outside cooling including mould cooling and water spraying cooling. To change the heat extraction pattern of the billet functioned solely from the outer surface, based on annular electromagnetic stirring (A-EMS) invented by Xu et al. (2010), Luo et al. (2017) proposed uniform direct chill (UDC) casting coupling A-EMS with intercooling in the direct chill (DC) casting process. An in-mold cooler was inserted to the melt sump, and thus the alloy melt temperature and concentration at solidification front become more uniform."

Jan 1, 2018

By Z. Bibak, S. Banisi, A. Ghasemi, E. Nematollahi

"The use of large AG/SAG mills in the mineral industry has been on the rise recently due to a significant reduction in the capital and operating costs for achieving significant increases in plant throughputs. The major reason for downtimes in these mills is the time taken for the replacement of broken or worn liners. This loss of “availability” of these units has a significant impact on the productivity of these plant operations. The ability to predict liner life time and its evolving shape could help to optimize these comminution operations. In the past decades, various models have been proposed to estimate liner wear rate, but because of their empirical nature they could only be used within certain limited operating conditions. In this research, a phenomenological model which could predict the liner wear rate was proposed and tested. This model considers parameters such as; operating conditions, liner hardness, pressure on the lifter, and, relative velocity of particles and mill shell. Data from industrially measured liner profiles were taken during the liner life time at the Sarcheshmeh and the Gol-E-Ghohar SAG mills to provide a solid base to calibrate and validate the model. The comparison of the model predictions with the actual measurements of the liner wear rate showed that the results were in a good agreement at both, the Sarcheshmeh (R2=0.94), and the Gol-E-Ghohar (R2=0.97) concentrators.INTRODUCTIONAG/SAG mills are one of the most important technologies in the mineral processing industry in the recent decades. The “Availability” of these units in a plant operation is one of the most important economic parameter for evaluating their performance. The major reason for the downtime of these mills affecting their “availability”, is the time required to change worn or broken liners (Yahyaei, Banisi, & Hadizadeh, 2009; Maleki-Moghaddam, Yahyaei, & Banisi, 2012). The knowledge about the magnitude and profile of liner wear not only enables more accurate liner life estimation to prevent unwanted interruptions of the SAG milling in mineral processing plants and more strategically plan the scheduled mill outages for liner changes. It also could provide key information needed to select an appropriate liner design (Yahyaei et al., 2009; Rezaeizadeh, Fooladi, Powell, & Weerasekara, 2010a)."

Jan 1, 2016

By D. Gorc, T. M. Fraser, Z. T. Nikic, R. Pesalj

"Mount Polley is an alkalic porphyry copper-gold deposit of Lower Jurassic age within the Quesnel terrane in south-central British Columbia. The silica-saturated Mount Polley intmsive complex is assumed to be coeval with volcanic rocks of similar composition in the Nicola Group in which it was emplaced. Other intmsions and some of the volcanic rocks in the Mount Polley area are silicaundersaturated and contain feldspathoids.The Mount Polley deposit is characterized by multiple intrusions that vary from diorite to crowded plagioclase porphyry to monzonite. Intmsion breccias are associated with some of the intmsive phases. Abundant hydrothermal breccias occur on the margins and above plagioclase porphyry intmsions. These breccias provide the main host for mineralization and are associated with the highest concentrations of copper and gold. The breccias are subdivided into four distinct types based on the dominant hydrothermal mineral in the matrix. Actinolite breccia is developed in an elongate zone within the core of the Central zone and grades laterally and vertically into biotite breccia to the southeast. Magnetite breccia is irregularly distributed and is relatively sparse throughout the deposit and albite breccia is dominant in the West zone. Pervasive and vein-related alteration correlates with the breccia types. The core of the hydrothermal system at Mount Polley is subdivided into three zones: actinolite, biotite and K-feldspar-albite. The margins of the core zone are overprinted by a discontinuous zone of calc-silicate minerals. This intermediate zone passes outward into propylitic alteration. Mineralization is most prominent within hydrothermal breccias and is generally present as disseminations, blebs within the matrix and abundant veins. Mineralization is associated with a chalcopyrite-magnetite-bornite assemblage in the core of the deposit passing out into magnetite-pyrite-chalcopyrite. Relatively constant copper to gold ratios suggest that both metals were precipitated under similar conditions.Hydrothermal breccias are genetically related to the emplacement of the crowded plagioclase porphyry melt. Crystallization of the melt was probably accompanied by volatile/aqueous exsolution, forming a water saturated carapace. Decompression of the chamber in response to magma withdrawal, fracture propagation and possible fault movement allowed hydrothermal brecciation to occur at the apex and margins of the intmsion. Alteration and mineralization appears to have been controlled by fluids migrating away from the plagioclase porphyry."

Jan 1, 1995

By S. Banisi, J. A. Finch, A. R. Laplante

"A technique for on-line simultaneous estimation of gas and solids holdup (volume fraction), based on a combination of conductivity and pressure difference measurements, is proposed and tested in a laboratory flotation column (10cm in diameter and 447cm in height). Fundamental concepts underlying this technique and the effect of relevant parameters are discussed. In the studied range, 3-30 %v/v gas holdup and 2-18 % v/v solids holdup, experimental results showed good agreement between the estimated and actual holdup values (as determined by an isolating technique). The relative accuracy of the solids holdup estimation increased when solids density or solids concentration increased. Frequent re-calibration of pressure transducers was found necessary for accurate phase holdup estimation.IntroductionGas holdup is a key parameter in controlling the performance of flotation columns. For example, flotation rate is affected by bubble size and gas rate both of which, in turn, affect gas holdup. Moreover, gas holdup also determines the slurry residence time which indicates a direct influence of gas holdup on recovery.Gas holdup determination has been the focus of many studies (e.g., Castillejos, 1986; Marchese et al., 1992). Some of the techniques which have been used are given in Table 1."

Jan 1, 1994

"Background:The recorded coal production in Nova Scotia from 1863 to 1980 was 390, 000, 000 short tons. This extraction was associated with an estimated 60,000,000 short tons of discarded material. This mining discard and coal washing plant reject are located in numerous, varying sized dumps throughout the mining areas. Approximately 70% of these dumps are in the Sydney coal field region of Nova Scotia.The coal content of these dumps varies from 10 to 30% coal with an average of 18%.Energy Costs:The explosion of energy costs in the mid-1970 's greatly increased the sale price of thermal coal which made recovery of coal from some of the dumps economical. The environmental spin-off of these operations will be the rehabilitation of the dumps upon cessation of the coal reclamation operation.Cape Breton Development Corporation, the owner of most of the dumps in the Sydney coal field was receptive to an approach by Selco of reclaiming coal from their dumps. The technology to be used, had been developed by an associate firm in the United Kingdom on similar mine dump situations."

Jan 1, 1983

By Jeff Stufsky

Debt Financing ?Broad Market Overview ? Recovering due to factors including: ? Increased trust in the system ? Enhanced capitalization of financial institutions ? The need to deploy capital for profit ? Competition: ? Investment-grade bond volumes increasing dramatically, and starting to pressure banks to compete with new capital ? Term Loan B financing from insurance companies and related institutions is returning, also pressuring banks to lend ? Local country financial institution capacity in Latin America has materially increased ? Results: ? Loan capacity increasing generally across instruments, regions, and sectors ? Financial institutions/banks starting again to seek yield as pricing competition heats up ? Tenors increasing with pricing coming down more slowly Underwriting is back in play

May 1, 2010

By Lynne Bowen

"On the da y shift in Number One Mine at Nanaimo on Vancouver Island, on May 3, 1887, William Griffiths, a coal miner with many years experience, fired a shot to advance the face of the crosscut. A flame ran out for a distance of fifteen feet along the roof and then extended up the slope for ten to twelve feet, and although many would have called this a blowing out shot, Griffiths said it was just a feeder. ""A blower"", he said, ""would have caused an explosion."" 1There was no explosion. Griffiths reported gas and the area was cleared for three hours and then work resumed. When the shift changed at 3:00 p.m., the fireman reported all places clear of gas and the ventilation good.2The ventilation in Number One Mine was the best anyone had ever seen. The air in the mine was almost too cold. The current was so strong that it sometimes blew out the flame on the miners' fish oil lamps. It delivered five to six hundred cubic feet of air for every man and animal working in the mine. The law required only one hundred cubic feet 3The miners considered Number One to be relatively safe. The manager was proud of the mine and its up-to-date equipment"". Recently, there had been reports from France and America about the explosiveness of coal dust, but the manager did not think his mine was sufficiently dusty to be dangerous.5 The dust lay thick on the floor of the mine. Sometimes when a shot was fired the dust rose in great clouds. When a miner was shovelling it, the dust would billow up and be carried off by the current of air. The dust was also in the roof and in the stopings, put there intentionally to fill up the spaces and prevent the accumulation of methane gas."

Jan 1, 1992