Search Documents

By H. Q. Fan

Construction equipment is an important type of resources of heavy construction contractors. Since equipment breakdowns can cause project delays and significant financial losses, the contractors are eager to know those factors causing equipment failures directly or indirectly, related to equipment design, maintenance, and operations. Although Bayesian network can be used for diagnostic analysis of failure events or making predictive analysis, building a Bayesian network for such purpose can be difficult as the cause-effect relations can be subjective and their conditional probabilities change with a wide variety of causal factors. A hybrid approach is proposed in this paper to update the Bayesian diagnostic network structures and parameters using real life data, the conditional probabilities and cause-effect relationships can be dynamically updated with observed failure records to reflect the real life situations of a complex equipment system. A case study is conducted to show the benefits of the hybrid approach in construction equipment diagnostic analysis.

Aug 1, 2013

By Y. Wang

In this study, homogeneous (unseeded) precipitation of nesquehonite (MgCO3.3H20) by the reaction of MgC12 with (NH4)2CO3 in supersaturated solutions at 30 °C was investigated. Factors which influence the precipitation of MgCO3.3H20, such as initial concentration, temperature, stirring speed, titration speed, equilibration time, have been studied. SEM images show that the initial concentration and titration speed have significant effect on nesquehonite's crystal morphology and particle size. In addition, stirring speed and equilibration time also have some influence on its properties. With the optimization of operating conditions, the crystals can grow up to a length of about 40µm and a width of 5µm, indicating good filtration properties. High purity nesquehonite obtained in this study was calcined to produce highly pure MgO at 800 °C as shown by XRD results. The novel process may be used to separate Mg and Li from high Mg/Li ratio brines in Qinghai, China.

Jan 1, 2007

By E. Herrera, L. Mariscal

"Ilo Copper Smelter operates since 2007 with an ISASMELTTM furnace as a single smelting unit (1,200,000 tpy) associated with two Rotary Holding Furnaces for separation of matte and slag, and which directly produces a discard slag. Southern Peru continually has been improving the slag chemistry of its ISASMELTTM furnace in order to reduce copper losses, given its big economic impact due to large slag mass generation. The present paper describes the influence of the CaO, Al2O3 and magnetite content in the slag of the ISASMELTTM furnace correlated with the SiO2/Fe ratio and its liquidus slag. Also it defines the best slag chemistry and operating practice in order to reduce the copper losses without compromise the bricks life of the furnace.INTRODUCTIONIlo Copper Smelter of Southern Peru (Grupo Mexico) is located on the southern coast of Peru, and treats mainly copper concentrates produced in its own mines (Toquepala and Cuajone).The modernized smelter was commissioned in 2007 and operates with an ISASMELT™ furnace as a single smelting unit (1,200,000 tpy), which is associated with two Rotary Holding Furnaces (RHF) for separation of matte and slag. This slag is directly sent to the dump. Figure 1 shows the smelter flow diagram.The ISASMELT™ process is a bath-smelting process using a single lance. The lance tip is immersed into a molten slag bath contained within the stationary, vertical, refractory-lined ISASMELT™ furnace. The injection of oxygen-enriched air, through the lance into the slag results in a highly turbulent molten bath. Feed material falling into the turbulent bath from above reacts rapidly, resulting in extremely high productivity for a relatively small bath volume."

Jan 1, 2012

By Marc Symbaluk

Core Programs Current ? Aboriginal Involvement Program ? Adaptive Forest Management / Forest History Program ? Grizzly Bear Research Program ? Natural Disturbance Program ? Foothills Growth and Yield Association ? Foothills Stream Crossing Program ? Fish and Watershed Program ? Caribou Landscape Management Association ? Social Science Program ? Local Level Indicators Program ? Communications and Extension Program ? Geographic Information Systems Program ? Mountain Pine Beetle Ecology Program In Development ? Climate Change Program ? Forest Community Program ? Water, Quantity and Quality Program (Water for Life) ? Circumboreal Initiative ? Yellowhead Ecosystem Management Group

May 1, 2008

By S. J. Laskowski

In potash ore flotation, carried out in NaCI-KCI saturated brine (about 6-7 molar KC1 and NaCI solution), long-chain primary amines are used as flotation collectors. Long-chain primary amines are poorly soluble in water and their solubility further decreases at high electrolyte concentration. For ionic surfactants there is a characteristic temperature (Krafft Point, KP) below which their solubility is too low for micellization. In a previous study, the effect of pH on the KP of dodecylammonium chloride in water was determined [Q. Dai and J.S. Laskowski, Langmuir, 7, 1361-1365 (1991)]. This paper deals with the effect of electrolyte concentration on the KP of dodecylammonium chloride. The derived theoretical relationship between the KP and the critical micelle concentration (CMC) for dodecylamine can be used to calculate the KP for electrolyte concentrations of up to 0.5 mol/L (about 8% NaCI-KCI brine). A simple experimental procedure for the determination of the KP for higher electrolyte concentrations is also described. The results show that the Krafft point of dodecylamine increases from about 17-18°C (in distilled water) to about 80°C at 16% brine saturation.

Jan 1, 2006

By W. Pietsch

For a number of reasons, solids entering and leaving facilities for the treatment of minerals are becoming increasingly finer. Such materials pose problems throughout processing. Solids featuring small particle sizes tend to dusting, result in losses and segregation, exhibit various storage, transportation, and metering problems, and fine particulate effluents can not be easily captured, used and/or recycled. Sustainable mineral processing must minimize the exploitation of natural resources and avoid the need for disposal of wastes. The first requires the use of lower quality raw materials and upgrading, which typically results in the production of fine grained concentrates, and the latter encourages the recycling of wastes and byproducts or efforts to investigate them as sources for secondary raw materials or other beneficial applications. To overcome the difficulties associated with fine particulate solids, size enlargement by agglomeration is necessary. The resulting products have free flow characteristics, do no longer dust or segregate, and are sized and shaped as required for optimum processing. In addition, agglomerated materials may be engineered to feature desirable structure, composition, and a number of related, improved properties. Such engineering may be applied for the modification of fine run-of-mine and up-graded minerals as well as the production of secondary raw materials from by-products or wastes. By the interdisciplinary application of size enlargement by agglomeration waste-free processing of minerals becomes feasible.

Jan 1, 2004

By E. Ghali, W. Zhang, M. Robichaud, G. Houlachi

"The performances of six mesh and one plate dimensionally stable anodes have been investigated in the zinc electrolyte at 38oC and compared to conventional silver-lead alloy anodes. The electrochemical behaviour of these anodes was studied by cyclic voltammetry, galvanostatic, potentiodynamic, open circuit potential and electrochemical noise measurements. It was observed that at the end of 24 h of galvanostatic polarization at a current density of 50 mA/cm2 in the zinc electrolyte at 38oC, the mesh V had the lowest potential followed by mesh III, mesh VI, plate-V, mesh IV, mesh I, and mesh II electrode. When the potentials for mesh I, mesh III, mesh IV, VI and plate-V, mesh V were compared with that of the Pb-0.7%Ag anode (1920 mV/SHE), they were found to be 6%, 16%, 7% 10%, 17% lower, respectively.After 16 h decay following the 24 h polarization, the mesh III had the lowest corrosion rate (51 mS/cm2) among the seven specimens, followed by the plate-V, mesh V, VI, IV, I and II (221 mS/cm2). For the fresh surface as received, after two hour open circuit potential measurements, mesh I had the most positive (noble) potential (1382 mV/SHE) among the seven electrodes followed by the plate-V electrode, mesh V, mesh IV, mesh VI, mesh III and mesh II (751 mV/SHE). After consecutive series of electrochemical testing, mesh V, mesh III, mesh VI had lower corrosion rates (~ 343± 6 µA/cm2) than that of mesh IV, mesh I, plate-V, and mesh II (~ 644± 143 µA/cm2).INTRODUCTIONThe continued use of lead based anodes in the electrowinning process has been mainly due to their relatively low cost as compared to other materials (Msindo, Sibanda, & Potgieter, 2010). They have good electrical conductivity, stability during electrolysis, very good corrosion and wear resistance (Ivanov, Stefanov, Noncheva, Petrova, Dobrev, Mirkova, Vermeersch, & Damaerel, 2010). However, lead-based anodes give their high energy consumption and low corrosion resistance for electrowinning. To overcome these problems, Dimensionally Stable Anodes (DSAs) has been chosen (Msindo et al., 2010). Comparing to the traditional lead anodes, the DSA anodes have many advantages: (1) no contamination; (2) no loss of anode material, pure electrolyte; (3) lower gas bubble effect through special anode designs; (4) use of higher current densities (Msindo et al., 2010). The success of DSA anodes has been attributed to their chemical stability that allows them to maintain nearly constant dimensions during the life of the anode even when operating in environment with low pH values. Due to their stability, the consumption rates of DSA are as low as 1 mg/amp.y (Alfantazi & Moskalyk, 2003)."

Jan 1, 2016

By S. Mohammadnejad, M. Olizadeh, B. Mehrabi

A new method using a combination of comprehensive mineralogical and analytical approach which includes optical and electrical microscopy and several analytical techniques with diagnostic leaching has been used to characterize the associations and distribution of gold in a variety of minerals from the Zarshuran refractory gold ore, NW Iran. Zarshuran ore with an average of 7.9 g/t Au-grade and about 8% arsenic with gold recovery less than 20% in direct cyanidation is considered as high arsenic, high au-grade refractory gold ore. In most of the refractory ores, gold is associated with arsenopyrite and co-para genetic ore minerals, while in Zarshuran ore; gold is associated with orpiment, realgar and arsenian-pyrite. Considering its mineralogy and As content, it can be considered as the most difficult refractory ore for characterization and processing. Results from the mineralogical examination and diagnostic leaches indicate that there is only a small amount of free gold (17-19%) that is present in cyanide-soluble sulfo-arsenides compounds, predominantly orpiment and realgar. Diagnostic leaches also indicate that little gold is occluded within the silicate structure (14%). Overall, the gold is mostly included in sulfides, arsenic sulfides and sulfo-arsenides (50%). The results also have shown how the technique can be used to gain a good initial understanding of potential metallurgical problems for a refractory gold ore.

Jan 1, 2005

By A. Pearson, F. A. Auld, S. O. Colbeck

"""The theory of buckling of shafts and Steel tunnel-linings"" was published by E. Amstutz in 1970 and commented on by S. Jacobsen in 1974. The authors have revised and enhanced Amstutz’s work to address Jacobsen's comments on its limitations and to extend its validity over a wider range of pipe/shaft geometries, including those commonly found in deep mine access shafts. The author has looked at Amstutz’s assessment of strengthening with flexible shear anchorages and adapted the theory of non-linear shear deformation response of bolts to develop a method of assessing increased buckling capacity utilising the full plastic shear capacity of studs. INTRODUCTION “Amstutz Buckling” refers to the buckling of pipe embedded in concrete under external uniform pressure. In terms of a mining environment, this relates directly to the design of a watertight shaft. This load case will commonly occur where a main shaft is cast against a geostatically stable primary liner and the only load applied to the final shaft is that of a uniform ground water load. Ernst Amstutz wrote his first paper on buckling of pressure-shaft steel linings in 1950 and subsequently improved his theory (Amstutz, 1970), which was then widely adopted for use within the industry. Years later, an alternative approach (Jacobsen, 1974) was proposed. Within his paper Jacobsen critiques Amstutz work, identifying some mathematical inconsistencies and highlighting limitations of the theory imposed by approximations adopted by Amstutz. Despite these limitations Amstutz work has still been used as the favoured design theory for use in the mining industry. In reviewing this body of work the author realised that with the advent of readily available computing software it was possible to adopt an iterative approach using Amstutz approximate formulae to find a solution to the original precise formulae, thus eliminating the limitations highlighted by Jacobsen The shear deformation to load characteristics of bolts has long been established (Crawford & Kulak 1968) and used for the plastic design of bolted connections in shear. This relationship is directly transferable to the design of shear studs, typical properties are well known, and actual values easily established in simple lab tests. The author has taken this relationship and modified Amstutz theory (Amstutz, 1970) for shear anchored strengthened liner buckling, to give a more efficient solution, using readily available material properties."

Jan 1, 2019

By H. Jung

The microstructures and grain sizes of nanocrystalline Co and Co-1.1 wt % P alloys were characterized by X-ray diffraction. The corrosion properties of as-deposited and annealed Co-l.l wt % P alloys and pure nanocrystalline Co were studied in a deaerated 0.1M H2SO4 solution using electrochemical measurements and XPS surface analysis. Potentiodynamic polarization testing and impedance measurements revealed that an addition of P to pure nanocrystalline Co improved the anodic-corrosion resistance, however, this enhanced corrosion resistance was compromised by the heat treatment process at 350 and 800°C. The corroded surface of annealed nanocrystalline Co-1.1 wt % P at 350°C exhibited a more porous P-enriched layer compared with the as-deposited case. A sample annealed at 800°C corroded uniformly showing second-phase precipitates. The enhanced corrosion resistance of as-deposited nanocrystalline Co-1.1 wt % P was attributed to the elemental P on the surface that acted to hinder the anodic dissolution kinetics of surface Co following an initial selective dissolution of Co. However, at a higher anodic overpotential region, the superior corrosion resistance of Co-l.l wt% P alloys did not last because of the formation of a non-protective surface film consisting of mainly hypophosphite and phosphate as well as elemental P.

Jan 1, 2005

By P. Espinoza, I. Yutronic, J. Olivares

"Compañía Minera Doña Inés de Collahuasi's (CMDIC) Concentrator Plant is located at 4300 meters above sea level, approximately 2000 kms north from Santiago, Chile. The concentrator has three grinding lines. Each one, Lines 1 and 2, have one SAG mill at the primary grinding stage followed by a secondary grinding and classification stage consisting of one ball mill, two hydrocyclone batteries and a sump with two pumps. Line 3 has one SAG mill (Gearless Mill Drive), followed by a secondary grinding and classification consisting two ball mills, four hydrocyclone batteries and a sump with four pumps. Average throughput for these three lines is 150 Ktons per day. Peak values of 180 ktons per day have been achieved.Since late 2008 and throughout 2009 and 2010, Operations and Automation areas developed an optimization program for the grinding process, considering the implementation of Model Predictive Controllers (MPC) for the three SAG mills, and later, extending MPC to the secondary grinding and classification stages. The implementation of a MPC solution was based on stability considerations (high variability of the SAG process, high interaction between sump level control and classification efficiency, etc), requirements for an automated and consistent operation, the need to maximize throughput under timevarying scenarios and, in the long term, optimization of grinding process considering Specific Energy Consumption, among other parameters. MPC solutions had proven control robustness and strong optimizing capabilities in terms of helping in discovering new operational points and so achieving all of the aforementioned goals.On the first stage of the program, MPC implementation considered identification of dynamical process control models based mainly on historical data, in order to know the impact of a group of Manipulated Variables over Controlled Variables. Also, the impact of measured Disturbance Variables was modeled in order to take into account the high impact and interaction of these variables over the processes. At the end of this stage, 4 controllers were successfully operating for the 3 SAG mills and the secondary grinding and classification process. In response to challenges made by the working group, the second stage of the development of control applications in the grinding process required to achieve a design and implementation of a solution capable of governing the milling process, in addition to stabilization and optimization of both processes (SAG milling and secondary grinding), to integrate from a point of view of process control and automation. Therefore, in the second stage, MPC performance was continuously monitored and optimized through advanced tuning, inclusion of more process models (with proper step tests), redefinition of specific optimization criteria and adjustment to new process needs.Finally, successful MPC implementation at Collahuasi has proved that fast development and deployment of process control solutions is possible and allows immediate process stability, higher throughput, specific energy consumption reduction, and successful product size control, among many others."

Jan 1, 2012

By Rob Assabgui

Presentation Overview ? Stobie Mine Sublevel Cave Background ? Elevated Silica Levels ? Silica Control ? Challenges and Issues ? Conclusions

Oct 1, 2010

By Manqiu Xu, Songtao Yang, Zongfu Dai, Robert Pelton

Five years ago, VALE Base Metals (then INCO), approached Pelton's group at McMaster and described a challenging mineral separations problem. The McMaster group has a strong track record in colloids, polymers, and chemical additives for papermaking; however, they had no experience in mineral processing. They proposed employing hydrophobic nanoparticles to replace conventional low molecular weight, water-soluble flotation collectors. Over the last five years, Vale, together with the Ontario Government (OCE) have funded two graduate students at McMaster who have worked closely with flotation experts at Vale. Experiments involving both very clean model mineral suspensions at McMaster and complex ores at Vale, have shown that hydrophobic nanoparticles do indeed function as collectors. Key nanoparticle properties and mechanisms have been identified and the technology has been protected in patent applications. Efforts to commercialize the technology are on-going. We believe that this project is a good case study demonstrating the advantages of industry-university collaboration and the use of outside experts, who may come up with novel solutions to complex problems.

Jan 1, 2011

By M. Nakai, G. Itoh, R. Yamada, A. Kurumada

In order elucidate the mechanism for poorer fatigue properties of 7000 series aluminum alloys than those of 2000 series alloys, the effect of the test environment on the fatigue crack growth of the two series alloys was investigated, considering the relationship to hydrogen embrittlement. Two 7075-type and four 2024-type alloys were T6-tempered and T4-tempered respectively, and subjected to fatigue crack growth tests in moist and dry environments. When tested in moist air, fraction of intergranular crack path was higher in the 7075-type alloy with coarse equi-axed grains than in the 2024-type alloy with similar microstructure. This was in accord with the larger crack growth rate in the 7075-type alloy. Both the intergranular crack path fraction and the crack growth rate were decreased by changing the environment to the flow of nitrogen gas. Thus, the large fatigue crack growth rate of the 7075-type alloy is attributable to hydrogen embrittlement.

Jan 1, 2015

By H. H. Bird

Kilembe is situated in the foothills of the Ruwenzori Mountains in Uganda. Precambrian stratiform copper de-posits are currently being mined at a rate of 90,000 tons per month. Complex ore structures and variable ground conditions have led to diverse mining methods in the past. New mining areas contain more shallow-dipping, highly contorted orebodies, in heavy ground. Cut-and-fill mining will be practised in the future. The geology, mining and milling are described.

Jan 1, 1968

By W. H. Gross

To pollute means to make impure or unclean. We tend to forget that man defecates, urinates, sweats, expectorates and exhales and in himself is a beastly little pollutor-but then so is Mother Nature! The object of this paper is to try to put what man and nature do into perspective. The facts indicate that although man may sweat a little, Ms. Nature is by for the greatest pollutor of all.

Jan 1, 1979

By M. E. Stutt, R. H. Rehder

"The mining industry is taking advantage of the increased performance resulting from the use of variable speed A C drives for large motors. This technology provides increased efficiency under the variable speed and torque requirements of such drives as mine hoists, conveyors, and air moving equipment. The technology does introduce voltage spikes on the voltage wave form that stress the insulation system to a greater degree than would occur with a constant voltage source. These voltage spikes must be considered in the design of the insulation system used for these motors.BackgroundHistorically the insulation systems for large AC motors were designed to withstand with reasonable life the voltage stresses of a 60 Hz constant sinusoidal voltage. One of the design tests is a voltage endurance test that requires the application of a 60 Hz voltage from conductor to ground equal to four to five times normal and establishing a time to failure. These higher than normal voltages accelerate the normal aging process by causing extensive partial discharge activity (corona) within the insulation system and the time to failure is a relative indication of insulation life.In addition to the voltage endurance test at 60 Hz, the individual coils are subjected to a surge voltage test to establish the withstand capability of the turn to turn insulation under switching surge conditions. The surge voltage is a fast rise time, 0.2 microsecond to crest value, voltage spike that can be caused by a circuit breaker or contactor closing operation. These voltage spikes can have a crest value of greater than 3.5 times the normal line to ground crest voltage of the normal 60 Hz power supply. The standard withstand test value is thus 3.5 times normal line to ground voltage. Because the voltage surges or spikes occur mainly during start and stop switching conditions, voltage endurance under these conditions has not been a major factor in insulation system design."

Jan 1, 1995

By Yuyong Li, Liangman Zhang, Zhaolian Wang, Shun Wang, Ltd. Shandong Huate Magnet Technology Co., Fengliang Liu

"Introduce a newly revolutionary magnetic separator - Raising Concentrate Grade and Decreasing Dregs Content Magnetic Separator Series JCTN (i.e. RCG&DDC MS JCTN). HUATE® JCTN is designed for rinsing, purification, desliming and thickening of the magnetic minerals as per different requirements. Adopting 240°-270° larger magnetic element with multi-poles and magnetic pulsation, and combining the devices of multi-channel rinsing water and top flushing water and new style tank, HUATE® JCTN can improve another 2%-10% concentrate mFe% than the traditional MS without lowering the concentrate recovery rate. Thereby, it solves the uneasy concentrate upgradation problem of the traditional MS resulting from the magnetic aggregation. Now, JCTN has been successfully applied in more than 30 mines in Australia, China and Russia, e.g. Sino Iron of CITIC PACIFIC MINING MANAGERMENT PTY LTD. HUATE® JCTN can optimize the industrial processing line by: 1) improving the discarding rate before milling to discard the necessary tailing ASAP; 2) getting in advance the final concentrate after milling. One JCTN can replace many traditional MS in series. In some way, it can also replace the anti-flotation separation process.INTRODUCTIONWe’re writing to introduce a newly revolutionary magnetic separator - Raising Concentrate Grade and Decreasing Dregs Content Magnetic Separator Series JCTN (i.e. RCG&DDC MS JCTN). HUATE® JCTN is designed for rinsing, purification, desliming and thickening of the magnetic minerals as per different requirements."

Jan 1, 2016

By Yosuke Ota, Makoto Tawara, Tetsuya Kojima

"Dry-lube has been used in Europe to enhance formability of aluminum sheet for automotive applications, but it is difficult to ensure degreasing performance with lower degreasing bath temperature. However, newly developed, highly lubricating pre-coats utilizing a urethane resin, which is soluble in water, have been found to show excellent degreasing performance. Furthermore, a richer pre-coat weight coincides with a lower friction coefficient and better formability. Combined use of anti-rust liquid oil showed different friction coefficient depending on applied surface pressure.INTRODUCTION The global demand for aluminum alloy products, especially for automotive application, has been increasing because aluminum alloys can offer excellent corrosion resistance with good strength and low density compared with steel. Aluminum alloys can contribute to saving much more energy and greenhouse gas emissions over the lifetime of the product. On the other hand, the amount of aluminum alloys in vehicle architectures is still somewhat limited due to relatively low formability. As a consequence of this low formability, it is necessary to set a certain limit to the shape of an aluminum alloy panel for automotive applications. So far hot melt wax dry lubricants have been in use especially in Europe as they have been recognized to provide better lubrication than conventional rust protection oils (Meiler & Jaschke, 2005). The benefit of hot-melt wax for automotive manufacturing is associated with a more stable forming process and the possibility to avoid extra lubrication in the press shop. But because of the low poorer solubility of hot-melt wax in degreasing aqueous bath solution, a higher degreasing temperature is required so that no remnant of hot melt wax can be carried over to the next manufacturing process. This temperature control is difficult to impress upon a manufacturing degreasing bath originally designed for liquid oil, especially in Japan. The typical temperature of degreasing bath in Europe is around 60°C, while it is only around 40°C. in Japan. Various types of pre-coats other than hot-melt with high lubricity have been reported (Tawara, 1993; Ueda, Hatsuno & Totani, 2013), but a balance between sufficient degreasing performance and high lubricity has not yet been achieved for an actual production process line."

Jan 1, 2018

By Robert MacPhail, Louis Racine, Bret G. Cousins

"Sodium Isopropyl Xanthate is employed in a wide variety of sulphide flotation procedures due to the specificity over other xanthates and the cost savings over other sulphide collectors such as thionocarbamates, xanthogen formates and dithiophosphates. An investigation carried out by Tennants Research Technology Applications (TRTA), has produced a chemically enhanced SIPX that has shown all the advantages of normal SIPX along with improved recoveries.Currently, FLEX 31 is manufactured at the Prospec Chemicals xanthate plant in Fort Saskatchewan, Alberta, Canada. Prospec, founded in 1983, produces approximately 4500 tonnes of xanthates per year and is presently undergoing expansion to produce approximately 6000 tonnes. The proprietary process for FLEX 31 is a new addition to plant operations that include the production of xanthates, thionocarbamates and xanthogen formates.This paper will cover the testwork on the zinc flotation circuit at the Louvicourt Mine in Val d'Or, Quebec. This testwork indicated that FLEX 31 could replace SIPX due to the ability of the FLEX to improve zinc flotation kinetics without adversely affecting final concentrate grade. FLEX has presently replaced SIPX in the zinc circuit at Louvicourt.BackgroundThe Louvicourt deposit is hosted by greenschist facies Archean volcanic rocks located in the southeast portion of the Abitibi Greenstone Belt. In the Val d'Or area, the volcanic rocks form an east-west striking, steeply dipping and south-facing sequence composed of thick mafic and ultramafic flows of the Lower Malartic Group.The joint venture has three partners-Aur Louvicourt Inc. (30%), Novicourt Inc. (45%) and Teck Corp (25%). Aur Resources holds 30% interest through Aur Louvicourt, a wholly owned subsidiary and is the operator of the project. Novicourt Inc. is 60.9% held by Noranda.Approximately 75% to 85% of Louvicourt's revenue comes from the sale of copper; 10% from gold (in the copper concentrate); 7% from zinc and 3% from silver (also in the copper concentrate) The copper at Louvicourt is fairly ""fast floating"". About 60% of the copper in the ore can be concentrated in the first flotation cells with feed grades of approximately 4% copper.The initial testwork and pilot trials had indicated that it would be difficult to achieve zinc grades over 52% and recoveries would have to be kept at a level amenable to salable concentrate grades. The actual mill results, with a fine regrind, achieved zinc grades of 55% to 56% at about 75% recovery."

Jan 1, 1996