Search Documents

By M. Mbonimpa

Field experimental cells were constructed in 2007 to assess the performance of different cover scenarios for the reclamation of the Parc 1 tailings disposal facility at the Westwood-Doyon Mine site (Abitibi, Quebec). Three configurations of cover with capillary barrier effects (CCBEs) with different thicknesses and material types for the moisture retention layer (MRL) were studied. MRL with 80 cm till, 40 cm till, and 40 cm clayey silt were used for cell nos. 2, 3, and 5, respectively. The capillary barrier layer (CBL) and drainage and protection layer (DPL) of the CCBE consisted of 30 cm gravel. A reference cell without cover was also constructed to compare the geochemical performance of the CCBEs. Due to an unexpected flooding in the leachate exit area of the cells in spring 2008, the cell instrumentation for hydrogeotechnical monitoring was postponed to spring 2009. Changes with time in volumetric water content, suction, soil oxygen concentration, and temperature were measured at different depths. This paper presents and discusses preliminary results obtained from spring 2009 to autumn 2010. In all cases, the degree of saturation Sr is lower in the CBL than in the MRL, indicating the presence of capillary barrier effects at the interface of these layers. Cell nos. 2 and 5 showed hydrogeotechnical behavior typical of an effective CCBE, with Sr maintained above 85% in the MRL and lower than 30?50% in the DPL and CBL. Based on the obtained results, and as expected, MRL thickness and the type of construction material used appear to affect the hydrogeotechnical behavior of the CCBE. Oxygen concentration profiles through the CCBEs were used to estimate the oxygen flux, and results indicate that cell nos. 2 and 3 performed better than cell no. 3. CCBE performance is currently being investigated using the geochemical monitoring data.

Aug 1, 2013

By B. Simonian

"The Mount Milligan mine, located in central British Columbia, began operation in September 2013 with a design nameplate capacity of 62,500 dry metric tonnes per day, using a conventional SABC grinding circuit followed by bulk sulphide flotation. Over the last few years, many changes have been implemented in order to debottleneck and optimize the comminution circuit to meet and exceed the nameplate design capacity as well as improve the metal recovery of the flotation circuit. This paper discusses changes, grouped into mechanical modifications, projects, and operational changes. The implementation of these changes as well as ongoing challenges and potential solutions will also be discussed.INTRODUCTION The Mount Milligan mine began production in the fall of 2013. It is a conventional truck-shovel open pit gold and copper mine and concentrator with a 62,500 tpd design capacity copper-gold flotation processing plant. The average head grades for the life of mine are 0.18% Cu and 0.39 g/t Au. At full capacity, the mine produces an average 400 dry tonnes per day of copper-gold concentrate containing approximately 21.5% Cu and 50-60 g/t Au. Current mine life is 21 years. This paper will discuss a selection of the operational, engineering, and administrative changes that have been made at the site since the publication of An Update on Reaching Nameplate Throughput and Continuous Improvement at Mount Milligan (Yue, 2017). PLANT FLOWSHEET CONFIGURATION Run-of-mine ore is crushed through a 60-110 gyratory crusher to a top size of seven inches. Up to 100% of the gyratory crusher product is diverted to the secondary crushing circuit by a moveable gate. The material diverted to the secondary crushing circuit is fed to a vibrating double-deck screen. The screen oversize is placed on a surge pile and reclaimed by four vibrating feeders to feed two 1250 kW standard head cone crushers in open circuit. The screen undersize is combined with the crusher discharge and returns to the conveyor feeding the coarse ore stockpile along with primary crusher product that by-passes the diverter gate."

Jan 1, 2019

By Denis Racicot

"L'Abitibi québécois a produit essentiellement de l’or, du cuivre, du zinc et de I' argent, ainsi que de faibles quantités de nickel, de plomb, de molybdène, de bismuth, de lithium, de fer et d’amiante. Depuis l’ouverture de la mine Horne en 1927, cent-cinquante mines ont contribué à la production de 1 420 tonnes d’or de 4,1 millions de tonnes de cuivre et de 4,7 millions de tonnes de zinc. Les productions minières annuelles ont été d'importance variable: des records de production ont été établis en 1955 pour I' or avec 35 tonnes et, vers 1965, pour le cuivre, le zinc et la quantile globale de minerai extrait avec respectivement 130,000, 275 000 et 13 millions de tonnes. Deux dépressions généralisées ont eu lieu, l’une vers 1946 et l'autre, a lafin des années soixante-dix. Des ralentissements de la production ont été observes pour le cuivre en 1953 et le zinc en 1959. Depuis le debut des années quatre-vingt. I' or et, de façon plus irreguliere, le zinc sont en progression, landis que le cuivre, malgre une hausse en 1983. pour suit son dec/in.La teneur de récupération des mines d’or est demeurée régulière et n’a subi qu’une faible diminution au cours des quarante dernières années. Célie du cuivre a diminué d'environ 50% dans la même période, landis que celle du zinc a subi d’import antes variations, aussi bien positives que négatives. Près des trois quarts des mines d'or ont une durée de vie inférieure à 12 ans et la distribution des tonnages de minerai extrait montre un maximum pour la classe de 100 000 à 1 million de tonnes. Du cote des mines de métaux de base, la durée de vie est plus étalée et les volumes de minerai ont une occurrence maximale dans la classe de 1 à 10 millions de tonnes.Concernant la distribution géographique de la production minière dans l'Abitibi québécois, le camp minier de Rouyn-Noranda vient en tête pour l’extraction de minerai et la production d’or et de cuivre. L’est sui vi par le camp de Val d'Or pour le minerai et l’or, landis que le camp de Chapais-Chibougamau occupe la deuxième place pour le cuivre avec une production équivalence a 60% de celle de Rouyn-Noranda. Le camp de Cadillac-Malartic suit de tres pres celui de Val d'Or pour ce qui est de I' or. Finalement, dans le casdu zinc, le camp minier de Joutel-Matagami domine largement avec une production qui a connu un développement accélère depuis 1963. Une analyse pré liminaire de ces données indique qu' i/ subsiste unpotentiel encore élevé de production d'or, décuivre et de zinc dans I' Abitibi québécois. ABSTRACTThe Quebec portion of the Abitibi belt has essentially produced gold, copper, zinc and silver, as well as some small quantities of nickel, lead, molybdenum, bismuth, lithium, iron and asbestos. Since the opening of the Horne mine in 1927, one hundred and fifty mines have produced 1420 tons of gold, 4,1 millions tons of copper and4,7 millions tons of zinc. Annual mine production has fluctuated: production records were established in 1955 for gold with 35 tons, and around 1965 for all extracted ore copper and zinc with respectively 13 millions, 130 000 and 275 000 tons. Two main recessions have occurred, the first around 1946 and the second during the late seventies. Cut backs in copper and zinc production occurred in 1953 and1959. Since the beginning of the eighties, gold production and to a lesser extent zinc production have been in progression. Except for a small jump in 1983, copper production is still declining.The average recuperation grade of gold mines has been quite steady and has only slightly diminished in the past forty years. The average copper recuperation grade was halved during the same time interval. For zinc there have been important ups and downs. At least three quarters of gold mines have an average lifespan of 12 years the tonnage distribution shows a peak in the 100 000 to 1 million tons class. Base metals mines show a more widespread life expectancy and have a tonnage peak in the 1 to 10 millions tons range"

Jan 1, 1990

By A. Anderko, R. D. Springer, R. D. Young

A thermodynamic model has been developed for calculating phase equilibria and other properties of multicomponent electrolyte systems. The model has been designed to reproduce the properties of both aqueous and mixed-solvent electrolyte systems ranging from infinite dilution to solid saturation or pure solute limit. The model incorporates formulations for the excess Gibbs energy and standard-state properties coupled with an algorithm for detailed speciation calculations. The excess Gibbs energy model consists of a long-range interaction contribution represented by the Pitzer-Debye-Hiickel expression, a second virial coefficient-type term for specific ionic interactions and a short-range interaction term expressed by the UNIQUAC equation. The accuracy of the model has been demonstrated for common acids and bases and for multicomponent systems containing aluminum species in various environments.

Jan 1, 2005

By P. Marcotte, G. LeBlanc, S. Ouellette, J. Boutin

"To characterize noise and vibration sources of different types of mining equipment used in underground mining, the authors performed a study in eight Quebec mines on 28 pieces of equipment. This paper presents the procedure followed to select the equipment to be evaluated, and the low-cost acquisition system developed to perform multichannel time-domain data acquisition in harsh environments. It also presents the results obtained for the noise level produced by the equipment and for handarm and whole-body vibration exposures.RÉSUMÉ Dans le but de caractériser les sources de bruits et de vibrations de divers équipements miniers utilisés sous terre, les auteurs ont étudié 28 équipements dans huit mines du Québec. L’article présente la procédure suivie pour choisir les équipements à évaluer ainsi qu’un système multicanal à faible coût développé pour acquérir des données dans des environnements difficiles. Il présente aussi les résultats obtenus pour les niveaux de bruit produit par les équipements et pour les expositions main-bras et du corps entier aux vibrations."

Jan 1, 2015

By G. Rong, W. Du

Stability of some potential unstable blocks in the left bank slope of Baihetan hydropower station is evaluated in this paper using the three-dimensional (3D) limit equilibrium method. The Baihetan hydropower station is in the downstream of Jinshajiang River, China. The geological condition in the river valley is complex, and many large discontinuities are detected in the slope of the two banks. As a result, much attention should be paid to the stability of the slope in the feasibility study stage. Because the left bank slope is an oblique consequent one, we mainly focus on the slope stability analysis in the left bank. Comprehensive geological exploration is conducted in the studied area and the detected discontinuities are well researched. By building a 3D geological model of the left bank slope, three potential unstable blocks which are close to the dam site are detected. An irregular wedge analysis method is then used to calculate safety factors of the three blocks under three conditions, which are natural condition, rainfall condition, and seismic condition, respectively. It is found that the safety factors of the block 1# and the block 2# are quite low when compared to the suggested values. Extra care must be exercised when excavating the slope near the block 1# and the block 2#. A preliminary reinforcement is also suggested.

Jan 1, 2015

By G. V. Fernandez

Sociedad Minera Cerro Verde S.A.A leaches secondary copper sulfides. In recent years, the mine has introduced innovations that have improved the management of mineral crushing, agglomeration, curing, and leaching. The crushing plant, for example, uses the concepts of degree of balance and percentage of time in an operationally balanced state which, displayed in real time, facilitate more intensive and uniform utilization of the crushers. High agglomerate quality is ensured with the correct dose of moisture, which is adjusted to the changing characteristics of the mineral through the use of electrical conductivity measurements. The amount of acid used for curing the agglomerate is also adjusted by using quality control information. Finally, the stockpile irrigation regime is managed using the criteria established by the "Lixiviant Request Rate", which optimizes the addition of leaching solution, creating such benefits as faster recovery, and reduced acid and energy consumption.

Jan 1, 2007

By J. A. Brown, F. P. Kerr, M. A. Archer

Extensive testwork on Global Atomic’s Dasa Project in Niger has been conducted at SGS Minerals laboratory in Lakefield, Ontario. Much of this testwork has focused on a two-stage counter-current leach as a means of improving leach efficiency and decreasing reagent consumption. The ore contains uranium mineralization requiring relatively high sulphuric acid concentrations during leaching to achieve acceptably high extractions. Excess free acidity in the leach solution may be utilized by recycling the high acid solution and contacting it with fresh ground ore. The resulting pregnant leach solution (PLS), now higher in uranium concentration and depleted in free acid, is forwarded on to uranium recovery by solvent extraction. The first stage residue proceeds to the second stage leach where fresh acid and oxidant are provided to leach the remaining uranium. This paper presents the results of the testwork conducted on both a Master Composite and Variability samples.

Jan 1, 2020

By M. H. Leite, R. Corthésy, D. E. Gill

"La connaissance des contraintes naturelles qui prévalent dans les massifs rocheux est un prérequis indispensable pour la conception sécuritaire et économique des excavations comme on en retrouve dans les exploitations minières souterraines. Certains chercheurs se sont attardés à colliger les résultats de mesures de ces contraintes et les ont utilisés pour produire des modèles de prédiction basés sur leur traitement statistique. Ces modèles de prédiction sont très populaires auprès des exploitants miniers puisqu’ils permettent, du moins dans les étapes préliminaires de design, d’obtenir de façon s’apéconomique mais approximative, une partie des paramètres dont ils ont besoin. Dans le cadre d’un projet initié en 1994 avec la collaboration de l’IRSST, il a été décidé de produire un modèle de prédiction englobant une partie de la zone périphérique de la faille de Cadillac, soit une zone plus restreinte que le Bouclier Canadien utilisé jusqu’ici comme région pour l’élaboration de tels modèles. Pour produire ce modèle de nouvelles données obtenues avec une technique permettant d’exercer un excellent contrôle de qualité ont été ajoutées à celles déjà disponibles. Une telle régionalisation des données de base permet d’obtenir un modèle où les intensités et les orientations des contraintes principales sont beaucoup moins dispersées que ce que rapportent les modèles publiés jusqu’à ce jour. Enfin, il est démontré que le modèle proposé pour la région étudiée est en toute probabilité plus sécuritaire que les modèles plus généraux publiés à ce jour. Knowledge of the in situ state of stress existing in a rock mass is essential to the safe and economical design of underground mining excavations. Prediction models have been published, based on the statistical treatment of stress measurement results. Such prediction models are very popular among mine operators because they allow them, at least at a preliminary design stage, to economically obtain part of the information needed, even if this information is approximative. In 1994, a research project financed by IRSST was initiated aiming to produce a prediction model that would comprise a peripheral zone around the Cadillac fault. This region is more confined than the Canadian Shield on which the existing prediction models have been based up to now. In order to produce such a model, existing stress measurement results have been used in conjunction with new stress measurements that have been performed based on a technique which allows full control of the quality of the measurements. Restricting the data upon which the model is based to a more specific region gives a model in which the intensities and the orientations of principal stresses are far less scattered than the results published to date. Finally, it is shown that the proposed model is probably safer for the studied region than the models previously published."

Jan 1, 1998

By Tadeusz W. Wlodek

THE known phenomenon that a test-piece of ferro-magnetic steel is magnetic after it has been broken in tension indicates that, while it is being loaded, the steel acquires magnetic properties. In the present investigation of the influence of the stress on the magnetic flux, repeated pulsating stresses of increasing amplitude, varying from zero to the maximum tensile value, i.e., pull-pull loading, were employed. The specimens were prepared from two types of carbon steel and two of alloy steel. The magnitude of the magnetic flux was determined indirectly. The voltage and mode of variation of the electromotive force induced in a coil surrounding the stressed steel specimen were measured as an indication of the varying magnetic flux within the specimen. Curves representing the electromotive force induced by the varying magnetic flux show that as the tensile load increased so also the magnetic flux increased, with a corresponding increase in measured e.m.f. At a certain stress there is a sharp bend in the voltage curve (point Win the diagram, Figure 5); this critical stress corresponds very closely with the yield stress (0.2 per cent permanent strain). Beyond this point, slight increases in the stress produce large increases in the voltage. The wave form of the e.m.f. was registered on an oscillograph. Analysis of the curves so obtained demonstrated the necessity of continuing these experiments, in order to determine the type of induced wave form associated with various types and amplitudes of stresses. In these experiments, the shape of the stress wave was sinusoidal, although the shape of the induced e.m.f. was sinusoidal only up to a certain load and became more and more complex above this load.

Jan 1, 1944

By I. C. Brown, J. F. Henderson

"IntroductionThe Yellowknife greenstone belt lies along the west side of Yellowknife bay on the north shore of Great Slave lake, some 600 miles north of Edmonton, Alberta. The producing gold mines along the belt include the Con-Rycon and Negus which came into production in 1938 and 1939, and the Giant Yellowknife, which followed in 1948. In addition to these, the Akaitcho and Crestaurum mines are potential producers and there are several promising prospects.Early geological work along the belt was done by A. W. Jolliffe who first recognized a number of great faults, the largest of which is the West Bay fault with a horizontal movement of more than 3 miles. In 1943, A. S. Dadson, following an examination of the Giant-Yellowknife property, advanced the hypothesis that Baker Creek valley was underlain by a series of major gold-bearing shear zones. Subsequent diamond drilling in 1944 bore out the correctness of this view and outlined the great ore-bearing shear zones that are now being developed and mined by Giant Yellowknife Gold Mines. Near the south boundary of the Giant property, the shear zones are cut off by the West Bay fault. This prompted Neil Campbell, District Geologist for the Consolidated Mining and Smelting Company, to make a detailed study of the geology along the West Bay fault in the hope of finding the faulted extension of the Giant shear-zone system on the west side of this fault. In this he was entirely successful. By careful geological mapping he matched several faulted diabase dykes on both sides of the fault and, knowing their dip, determined the horizontal and vertical components of movement along the fault. Subsequent •diamond drilling based on Campbell's work located the presumed correlative of the Giant shear-zone system on the Con-Rycon and Negus properties, where it has been named the Campbell zone or system. At the present time, all production at the Negus Mines property is coming from orebodies along the Campbell zone."

Jan 1, 1950

By J. M. Harrison

FIELD PARTIES of the Geological Survey of Canada have, in recent years, mapped several areas east and northeast of Flin Flon (9, 10, 12, 13, 14, 15, 118) (1). In all these areas the mineral deposits show a close geographical relation to faults although the immediate control of most of the known ore deposits appears to be folded structures in the rocks (8, 11, 18, 19). Air photographs and published geological maps were studied in order to ascertain whether or not the mineral deposits in the Flin Flon-Snow Lake mineral belt as a whole show any spatial relationship to faults. It was found that most of them do show a distinct geographical association with faults, or with topographic features that may be faults. It is further apparent on air photographs that a major lineament, for composite of lineaments, follows approximately the contact between gneisses and schists of the Kisseynew complex on the north, and Amisk volcanic rocks on the south. However, this Kisseynew lineament is not continuous and, especially in the eastern half of the district, it is exceedingly irregular in plan. Parts of this lineament have been mapped as faults (9, 10, 12, 14), other parts have been shown as stratigraphic contacts (1, 2, 21, 27), and still other parts have not been studied except by reconnaissance methods. It is suggested that the Kisseynew lineament may be due to a deformed fault that extends easterly from a point about 25 miles west-northwest of Flin Flon to a point at least 10 miles northeast of Wekusko lake and that the mineral deposits.

Jan 1, 1951

By F. Gaul, H. R. Manouchehri, A. Mosser

"Mining is a major energy intensive industry that contributes in consuming about 7% of the total world’s energy in which almost half in comminution. The underlying trait that drives energy consumption upwards appears to be somewhat persistent due to increasing in population, demands and growth rate. High grade resources have been/being depleted; consequently, low grade, high competent and complex ores with complicated geological structure are brought into perspective. For efficient extraction of values from such resources comprehensive multistage mining and processing strategies must be taken into account. Different treatment technologies, including ore sorting, must be considered to improve resource efficiency and productivity while taking into account the reduction in energy and water consumptions and related sustainability issues.The implementation of sorting technology in mining industry has a long past and its impacts on improving the overall efficiency of both mining and milling have been proven. However, the lack of complete understanding of its potential combined with ore complexity and low capacity of sorting machines have prevented the large scale application in mining industry. The application of X-Ray transmission sorting at Mittersill Tungsten Mine in Austria is presented and discussed herein. A technoeconomic analysis of the technology has revealed a significant potential of adding value to the concentration process. The rough feasibility study has given a strong feed-back on profitability and short time payback of about 2 years for the investment. Except the economic benefits the technology has positive environmental impacts. The potential for saving energy and water is large. The rough calculations have revealed that the energy saving can be up of 840MWh/annum. Furthermore, the ongoing cooperation between Mittersill mine and the sorting manufacturer is a good example on how the development of more competitive products, and product offerings, can be made."

Jan 1, 2016

By F. A. Auld

"Traditionally deep shaft sinking from the ground surface was carried out using drill and blast methods. Although large diameter blind shaft drilling has been carried out successfully on numerous occasions previously, including as early as 1852 in Germany (Auld, 1995), little attempt has been made until more recently to mechanise the shaft sinking excavation process using down-the-hole machines. This paper reviews the development of deep shaft sinking machines from the early 1970’s up to the present day. INTRODUCTION Mechanical excavation methods can significantly improve excavation performance, in order to access natural resources faster, and labour safety is increased compared to drill and blast operations. However, shaft sinking machines need to be capable of accommodating all the basic requirements for deep shaft sinking, namely: 1. Excavation and muck removal 2. Ground stability control 3. Groundwater ingress control 4. Temporary lining installation 5. Permanent lining installation and watertight sealing 6. Ventilation 7. Secondary means of egress for personnel In addition, how the machine operates in the shaft is an important factor, either slung on ropes from a surface headgear or on its own in the bottom of the shaft. An all-embracing machine which can deal with all of the above conditions is impossible but many of these requirements can be incorporated into a single machine. Deep shaft sinking also differs greatly from normal tunnel construction which employs the use of either a roadheader arm installed within a shield or a full-face tunnelling machine for excavation. Hydrostatic pressure and ground stability problems increase with depth, whereas in tunnelling the depth is normally relatively shallow and the aforementioned factors remain approximately constant along the tunnel length. DEEP SHAFT SINKING MACHINES All the shaft sinking carried out previously in the UK was by the traditional method of drill and blast. Elsewhere, in other parts of the world, attempts have been made to mechanise the process."

Jan 1, 2019

By M. Dupuis

In the present study, the heat balance of the Hirakud smelter aluminium reduction cell has been accurately assessed using only a surface thermocouple and a pyrometer, As it is well known that using a single linear or quadratic relationship to estimate the heat flux from the measured surface temperature does not provide the accuracy required to close the cell heat balance, this approach was not used in this study, Instead, the fundamental natural convection and radiation heat flux equations were used systematically for each measurement point, Practically, this means that the ambient air temperature and at least one ambient radiative temperature must also be known in addition to the surface temperature for each measurement point. Sometimes, the radiative heat flux could not be accurately estimated using a single ambient radiative temperature, In those cases, a more accurate estimation based on two ambient radiative temperatures and corresponding view factors has been used instead, It turns out that although at least three temperature measurements are required to estimate a single heat flux, it takes a lot less time to make those temperature measurements using a pyrometer than directly measuring the heat flux using an expensive heat flux meter, Furthermore, no loss in accuracy was detected when using this approach as the cell heat balance could be closed within 5%, the level of accuracy typical of cell heat balance assessment using heat flux meter.

Jan 1, 2004

By M. Barati, K. Ebrahimi-Nasrabadi, P. W. Scott

"The conversion of cryptocrystalline magnesite to caustic magnesia was studied experimentally at temperatures of 400–1,200°C and for calcination times of up to 8 h. A differential thermal analysis– thermal gravimetric analysis showed that decomposition begins at temperatures as low as 340°C and is completed at 600°C. Specific surface area, iodine adsorption number, crystallite size, and loss on ignition were measured to characterize the product quality. It was found that high-quality caustic calcined magnesia can be produced in a narrow temperature (600–650°C) and time range (1–4 h).RÉSUMÉ La conversion de magnésite cryptocristalline en magnésie caustique a été étudiée de manière expérimentale à des températures de 400 à 1200 °C et pour des temps de calcination atteignant 8 heures. Une analyse thermique différentielle – analyse thermique gravimétrique montre que la décomposition commence à des températures aussi basses que 340 °C et qu’elle est complète à 600 °C. La surface spécifique, l’indice d’adsorption de l’iode, la taille des cristaux et la perte au feu ont été mesurés afin de caractériser la qualité du produit. Il a été trouvé qu’une magnésie caustique calcinée de grande qualité peut être produite dans un petit écart de température (600 à 650 °C) et dans une période de temps variant entre 1 et 4 heures."

Jan 1, 2015

By T. ?kre, O. M. Dotterud, S. Haarberg, J. Thonstad, G. M. Haarberg

An electrowinning pilot plant has been constructed at Falconbridge Nikkelverk A/S, Kristiansand, Norway. The equipment consists of a mixing tank where the electrolyte composition and temperature are controlled, an electrowinning tank equipped with five cathodes and six anodes of commercial size and design and a dechlorination facility. Electrowinning experiments were carried out in this pilot plant using acid cobalt chloride solution from the cobalt tankhouse. Key parameters were varied to obtain an improved understanding of the cobalt electrowinning process, focusing on the detrimental deposition of cobalt oxide on dimensionally stable anodes. The extent of anode scaling was found to be dependent on the electrowinning conditions. Low pH, temperature and cobalt concentration resulted in less scale being formed, however at the expense of cobalt current efficiency and cell voltage, adversely affecting electrowinning production capacity and energy consumption. When operating at high acidity, pH in the anolyte was higher than in the catholyte, which is believed to be due to H+ ions taking part in the current transport across the diaphragm, migrating out of the bags surrounding each anode.

Jan 1, 2005

By L. Don Leet

Abstract Earthborne vibrations from blasting and other sources, including rock bursts, can now be recorded effectively. The nature and magnitude of vibrations from various sources have been investigated and certain applications of the knowledge thus gained have been made. Vibrations from blasting have been measured on special equipment over a range from an electric blasting cap at a few feet, through the largest quarry shot in history to date ( 1,-362,985 lb.), to the first atomic bomb, in uew Mexico on July 16th, 1945. Laws relating amount of explosive to amount of vibration at different distances have been developed and tested. Special studies have been made of the effects of vibrations on buildings, particularly from the standpoint of possible structural damage. Recorded vibrations are used to study the effects of modern short-period delay shooting. It ?has been found that short-period delay firing is extremely effective in reducing vibrations under the right conditions, but with certain limitations. In quarry shooting, there appears to be a minimum number of holes below which vibrations are not appreciably reduced by short-period delay firing. In several instances this minimum has been near 7. Vibrations in the ground from rock bursts and the effects of mining in stresesd ground have been studied both underground and on the surface in a search for a rock burst warning system. Introduction Earthborne vibrations from blasting and other sources, including rock bursts, can now be recorded effectively. Analyses of blasting records have been yielding increasing funds of information of practical as well as theoretical interest. The nature and magnitude of the vibrations have been investigated with special reference to their effects on structures.

Jan 1, 1951

By W. Mueller, M. Rocheleau, E. Dimroth

The paleogeographic evolution of the Abitibi Belt is subdivided into three phases, namely: 1) a phase of the growth of a submarine volcanic chain, 2) a phase of the emergence and growth of volcanic islands and 3) a phase of uplif t and erosion of volcanic islands. Isostatic calculations suggest that the volcanic sequence in the south of the Abitibi Belt rests on oceanic basement or on the mantle; the volcanic sequence in the north of the belt rests on about 13-14 km of tonalitic basement. 10-15 km of plutonic material accreted to the volcanic islands during paleogeographic phases 1 and 2, and caused the uplif t during paleogeographic phase 3.

Jan 1, 1984

By E. P. Williams

"Prince Edward Island, Canada's smallest Maritime Province, is located in the southwestern part of the Gulf of St. Lawrence. The Province is more or less centrally located in the Maritimes Basin, a large intermontane basin within the Appalachian orogenic belt. The Maritimes Basin is subdivided into sub-basins and uplifts which exhibit two dominant structural trends: east and northeast. The Basin is known to be petroliferous because of the seeps, shows, oil shales and albertite found in southern New Brunswick and northern Nova Scotia and the gas and oil produced from the Stony Creek field near Moncton, New Brunswick.Permian beds are exposed on the Island, mostly along sea-cliffs. A maximum thickness of about 5,000 feet of red beds -shales, sandstones and conglomerates -make up the sequence. Over most of the Island, the Permian section is much thinner. Four key wells (Mississippian tests) and several shallower tests have been drilled. The Pennsylvanian-Mississippian section thickens rapidly off the Port Hill Uplift at the northwest, where it is less than 4,600 feet thick, and continues to thicken to about 20,000 feet in the Cumberland Basin at the southeast. Geological and geophysical data combine to give us the structural picture of the deeper beds.Prospective reservoir rocks are primarily in the Missis-sippian Horton and Windsor groups. Prospects are:-1. on or over structural highs in the basement; 2. on anticlines or fault highs; 3. over or peripheral to salt domes or salt-core anticlines; 4. at truncation pinchouts of Mississippian prospective beds; 5. in basal sandstone or granite wash on the pre-Carboni-ferous basement; and 6. in facies traps at changes from sandstone to shale or porous to tight carbonate rocks."

Jan 1, 1967