Search Documents

By S. M. Fatemi-Varzaneh

The AZ31 magnesium alloy is considered as a promising alloy in various applications and industries. Furthermore, to design a proper hot working process (rolling, forging and extrusion), the assessment of hot working behaviour of the alloy is necessitated. Accordingly, the hot deformation behaviour of AZ31 alloy was studied through hot compression testing method. The latter was carried out in a wide range of temperature (523 K to 783 K) and strain rates. The obtained true stress-true strain curves and final microstructures were examined and a partial melting was realized at 740 K. It was concluded that the presence of liquid did change the deformation mechanisms thereby affecting the flow behaviour.

Jan 1, 2005

By L. M. Guayacán-Carrillo, G. Armand, A. Noiret, D. Seyedi, S. Ghabezloo, J. Sulem

"The main purpose of this paper is to analyze the convergence measurements in a drift excavated in the Callovo-Oxfordian claystone. The drift axis is in the direction of the major principal horizontal stress whereas the stress state is quasi-isotropic in the drift’s section. The initial geometry of the drift being circular, the anisotropic character of the deformation is taken into account by assuming that the drift shape evolves in an elliptical shape. The convergence measurement data on six different points around the drift are analyzed to identify the main axes of the deformation ellipse, following the methodology proposed by Vu et al. (2013, Rock Mech Rock Eng, 46, 231-246). Then, using the semi-empirical law proposed by Sulem et al. (1987, Int J Rock Mech Min Sci, 24, 145–154), the convergence evolution is fitted independently for each axis of the ellipse. This method permits to distinguish two effects: the face advance effect and the time-dependent behavior of the ground. The results for the two directions of the ellipse axes show very close values for the parameters describing the time-dependent properties of the ground, the distance of influence of the face, and the extension of the decompressed zone around the gallery. Such model can provide valuable insights for predictions of the convergence evolution in the long-term. INTRODUCTIONDeep disposal of radioactive waste has been studied in France for more than two decades. The French National Radioactive Waste Management Agency (Andra) began in 2000 the construction of an Underground Research Laboratory (URL) with the main goal of demonstrating the feasibility of a geological repository in Callovo-Oxfordian claystone. Several research programs have taken place to improve the knowledge of the rock properties and its response to the excavation progress. The optimization of supports design for long-term behavior is an important point to develop. A network of experimental drifts has been constructed with variations on: excavation method, structure geometry, supports system and orientations with respect to in-situ principal stresses’ directions. In each drift different sections have been instrumented to monitor the convergence evolution and the rock deformation. Continuous monitoring of the excavated zone around the drifts revealed the development of a fractured zone (extensional and shear fractures) induced by the excavation. The extent of this fractured zone depends on both the drift orientation and the in-situ stress field (Armand et al., 2014). Indeed, the fractures distribution has an important influence on the convergence of the drifts."

Jan 1, 2015

By D. Sbarbaro

In many modem concentrators the use of supervisory systems in their grinding circuits has meant more consistent operations and increases in capacity. These systems rely on a series of specific algorithms that uses different pieces of information and drives actions over the process. One of these algorithms is the ball mill overload detection, which plays an important role in any supervisory strategy designed to maximize ore feed rate in wet grinding circuits. This paper introduces different overload detection algorithms, and compares them in terms of the time taken to detect the overload condition. This comparative analysis is based on highly noisy power draw measurements obtained in an industrial plant.

Jan 1, 2007

By H. E. Johnston

There are currently a number of options in terms of plant feed comminution tests: Bond work index tests, JK drop weight and SMC tests, SPI, low impact crusher work index tests, to name a few. However, information regarding specific energy requirements for regrind mills is often requested, which can be difficult or very expensive when only a small mass of concentrate is produced from bench-scale flotation tests. This research was aimed at developing a test methodology that would produce a similar result as an IsaMill Signature Plot but require less sample mass allowing for preliminary estimates of regrinding power at a lower cost. Initially, the laboratory test methodology was completed on a single sample in comparison to the IsaMill Signature Plot for that sample. Results indicated a very good correlation between the laboratory tests and the IsaMill Signature Plot for this sample, though some parameters did impact laboratory regrind mill efficiency. The developed methodology is subsequently being applied to a range of concentrates, investigating a range of material particle sizes and material types, in comparison to a full IsaMill Signature Plot on the same sample. This new test procedure has been called ‘The Eliason Test’.

Jan 1, 2014

By J. P. Norrie

The presence of copper-bearing rocks in the Coppermine River area of Arctic Canada has long been known. Word of this was probably circulated along the Arctic and Hudson Bay coasts by the Eskimo, who no doubt traded articles made from native copper among themselves. It is not known whether any of these ever reached the southern shores of Hudson bay. The Indians, also, knew of the occurrence of copper here, as they served as guides to Hearne when he made a successful trip over land from Hudson bay to the Coppermine river. The possible commercial importance of these copper deposits was early appreciated by the Hudson's Bay Company, who on December 7th, 1770, despatched Samuel Hearne from Fort Prince of Wales, now Fort Churchill, to investigate them. He reached the then unnamed river at a point forty miles from its mouth on July 14th, 1771, and after surveying the river to its mouth and naming it the Coppermine, he retraced his steps to Fort Churchill by an overland route. Hearne's expedition was probably the most remarkable and arduous ever attempted in Arctic exploration, but the actual value derived from the trip was entirely out of proportion with the hardships he must have suffered. He verified the occurrence of native copper, but his astronomical and other observations were of little value. Until 1912 no concerted effort was made to obtain any definite information as to the geology and economic value of the Copper-mine deposits.

Jan 1, 1931

By Scott Hean

"Environment and the economy are interwoven irrevocably. They need to be publicly discussed, and discussed often so that new approaches can be understood and developed - approaches which are complimentary, not confrontational.Discussion on the environment is timely, from the perspective of mining engineers and developers, from that of bankers and from their shared perspective as people concerned with enhancing the quality of life, the environment and the economy.This paper will touch on how what is called the ""environmental economy "" that has evolved has become entangled with regulatory and financial issues in a way that is dangerous for all of us. It will also look at some of the promising possibilities that a world-wide and continuing concern for the environment holds out for us.For many decades, British Columbia has provided some of the key examples of the intertwining of environmental and economic issues, and, very importantly, providing the people prepared to do something about them.Canada's first environment minister, the late Jack Davis, came from British Columbia. He led this country's delegation to the Stockholm Environment Conference in 1972, a conference that laid the groundwork of principles necessary to establish some international certainty as to the legal liability for causing trans-national environmental damage.Another British Columbian who was also a national environment minister, John Fraser - now the Speaker of the House of Commons - was one of the first to dramatize the importance of acid rain and force it into the international public arena.Some 20 years ago, British Columbians made Vancouver and their province one of the major centres of opposition to the Alaska Pipeline and Tanker System - with some justification, it now seems.That a British Columbian , then MP David Anderson, was given legal recognition to sue in a United States' court against a system that was either in U.S. territory or international waters was an important precedent in, and of, itself in terms of environmental law. That old controversy is now a very current case study - in terms of dealing with the question of liability.-"

Jan 1, 1991

By L. S. Jen

Canadian copper, nickel, zinc, lead and molybdenum mines are characterized by the mining of ores from which more than one metal is recovered. During the 1980s, approximately 15% of the gold, 25% of the zinc, 30% of the copper, 55% of the molybdenum, 80% of the silver and 90% of the lead produced from Canadian mines were produced as co-products and by-products of base metal mining operations. This trend is not expected to change significantly in the near future. The presence of co-products and by-products affects the level of production and the level of revenue from base metal mines in several ways: (I) in general, production of one base metal cannot be expanded or cut back without affecting the amount of production of another metal;(2) the commercial success of certain base metal mining operations depends on the substantial bonus revenues from co-products and by-products; (3) the quality and economic viability of many ore deposits are significantly improved by the presence of co-products and by-products; and (4) while coproduction is critical to the survival of some mines, bonus revenue from by-products can also be life saving to others during economic downturns. For these reasons, deposits with significant co-product or by-product values are likely to continue to be significant targets for exploration and for acquisition.

Jan 1, 1992

By J. Currie, J. McManus, R. Chenier

"Cominco Copper Division's Valley Mine is located in the Highland Valley of British Columbia, approximately 275 km by air northeast of Vancouver. The nearest towns are Logan Lake, located IS km to the east and Ashcroft, located about 50 km to the northwest.Preproduction stripping of rock and overburden at the Valley Mine's Lake Zone Pit began in mid-1982 following a decision to discontinue mining in the adjacent Jersey Pit. Equipment and mining methods were carried over from the Bethlehem Copper operations which, with Valley Copper Mines, were merged into Cominco in December 1982.Blasting practices, as carried over from the Bethlehem pits, were designed to provide the fine fragmentation required to meet production requirements using the Bethlehem crusher. However, after mining the first few benches of the Lake Zone Pit, it became apparent that overblasting at the pit limits was causing a number of bench failures, as well as contributing to an over-all reduction of the material strength of the rock mass forming the southwest wall of the pit.With present ultimate pit plans calling for the southwest wall to be as high as 300 m, Valley staff realized that potential slope stability problems should be dealt with as early as possible. This philosophy would enable experimentation on phase pit walls in order to attain the optimum slope angle on the ultimate pit wall.As part of an over-a ll slope stability program, a controlled blasting program was initiated at the Lake Zone Pit in March 1983. In this program, Valley engineering and production staff worked together with Golder Associates in establishing design criteria and evaluating the results. This program resulted in a marked improvement in the soundness of pit walls while maintaining the required degree of fragmentation."

Jan 1, 1985

By G. Robert Guillet

"Ontario enjoys the advantage of its proximity to the large industrial market of northeastern North America. Together with Quebec and fifteen nearby U.S. states, an industrial base of more than half the total for both countries is provided by a population of 100 million.Mineral fillers such as barite, calcium carbonate, kaolin, mica, silica and talc are of major importance in the manufacture of paper, paint, plastics, rubber, vinyl tile, carpet backing, putty, caulks, sealants and adhesives. Ontario has all of these minerals, but domestic production falls short of demand in some cases, and mica and kaolin are not produced at all.This paper reviews the market and outlines the distribution of the major filler-consuming plants of northeastern North America. It also identifies the principal producers of filler minerals in the United States and Canada.IntroductionOf all the uses for industrial minerals, mineral fillers are probably the least understood. Originally used primarily to add low-cost bulk to a variety of commodities without seriously affecting their properties, filler minerals have become essential components that enhance and extend the properties of their hosts. Hence the term ""extender"" which, for all practical purposes, is synonymous with ""filler"". Today, fillers and extenders are not solely low-cost additives, but ingredients that provide essential characteristics to the products they fill.The major markets for mineral fillers are paint, paper, plastics, rubber, adhesives and floor coverings. But there are many others: putty, pesticides, wire and cable coatings, caulking and asphaltic compounds, oilcloth, wall-paper, joint cements, inks, sealants and many others. Barite, calcium carbonate, kaolin, mica, silica and talc are among the more important filler minerals discussed in this paper, but there are at least a dozen others. And the increasing practice of coating the mineral surfaces with certain coupling agents or metal stearates is constantly expanding the range of characteristics and hence the marketing opportunities.Whiteness, particle shape, fineness of grind and cost are the principal considerations in selecting a filler, but other characteristics such as weight, opacity, hardness and chemical inertness may be dominant considerations in specific applications."

Jan 1, 1987

By J. D. Galloways

The northern part of the P. G. E. railway traverses and opens up that part of the province known as the Cariboo district, comprising the Cariboo and Quesnel Mining Divisions, which are a part of the Northeastern Mineral Survey District. Williams lake, a divisional point on the P. G. E. is near the southern boundary of the Quesnel Division and from this point the railway runs northerly to Quesnel, its present terminus. From Quesnel the railway is projected and partially constructed to Prince George on the Canadian National railway; therefore its general trend is northerly through the heart of the Cariboo district. Early History There is no need to outline at any length the early history of mining in the Cariboo. It is sufficient to say that the great gold rush to the Cariboo, in the early sixties, was practically the commencement of mining in British Columbia. These early placer mining operations centred around the old towns of Quesnel Forks, Keithley Creek, Barkerville and Van Winkle, the latter now called Stanley. Many millions of dollars of placer gold have been taken out and the end of production is not in sight yet. The maximum yearly production was reached about 1863, after which there was a gradual decline in output. During the war years production was at a very low figure but a steady, even if small, increase has occurred in the last three years and prospects are encouraging for a much greater output.

Jan 1, 1925

Most of automotive magnesium applications are presently produced by high-pressure die casting processes, For further expansion of the alloy usage in automobiles, novel-manufacturing processes needs to be developed, In this study, squeeze casting of AM50 alloy was carried out using a hydraulic press with an applied pressure of 70 MPa, Tensile properties and fracture behavior of the squeeze-cast AM50 were characterized in comparison with the die cast counterpart, The squeeze-cast AM50 alloy exhibits virtually no porosity in the microstructure evaluated by optical microscopy, The results of tensile testing indicate that the improved tensile properties for the squeeze-cast samples over the conventional high-pressure die-cast parts, The analysis of tensile behavior shows that the strain-hardening rate during the plastic deformation of the squeeze-cast specimens is constantly higher than that of the die-cast specimens. The SEM fractography evidently reveals the ductile fracture features of the squeeze-cast alloy AM50.

Jan 1, 2005

By R. Lovat, J. A. Hunter

"The design, development, and verification of the Lovat 7.6metre diameter full-face tunnel-boring machine is reviewed. Programmatic and technical challenges are outlined with a review of the specifications and the design to meet these requirements. Subsystem designs are presented for the waste material removal, ventilation, cutter head, structural support, advance technique, water removal, and interfaces with the Donkin-Morien Mine. The techniques used to verify that the design meets the requirements is by testing in the Lovat factory and in the field. Certification of the machine for use in a methane environment is discussed.IntroductionStudies have concluded that the average annual worldwide tunnel construction is 500 kilometres at an estimated average co st of $3,400 U.S . per linear metre. The total market value of the tunnelling industry is estimated as approximately $1.7 billion U.S. per annum. Of this, the current market for tunnelboring machine excavation is approximately $270 million U.S. per annum worldwide with a further potential of $250 million if more contractors are convinced that Tunnel-Boring Machines (TBM) are more suitable than conventional techniques. The worldwide civil tunnelling market has the potential to double each year in the next 5 to 15 years. Growth has been identified in the energy and mineral resources sectors of the economies of many nations and a significant volume of machine tunnelling studies and trials are presently underway for the extraction of coal, uranium , heavy oil or oil sand fuels, metallic and non-metallic industrial minerals and base metal or rare earth ores. Further tunnel projects for regional transportation, waterpower, irrigation , high density urban transportation, storm water sewers and water supply purposes are continually being implemented with new concepts like military security facilities and underground storage schemes being considered.Lo vat Tunnel Equipment of Rexdale, Ontario, the only Canadian manufacturer of TBMs was incorporated in 1973 to manufacture so ft ground tunnel-boring machines to satisfy this growing market demand. Lovat has produced an average of 5 machines per annum during the period 1972 - 1982 and has established an international reputation for competitive costs, quality of construction, after-sales service, and reliability. As of June 1982 Lovat TBM's have been used to tunnel over 240 km in projects throughout the world."

Jan 1, 1984

By Hugh K. Taylor

"With some justification, people have long complained about the indefinition of ore reserves. Perhaps they were led to expect too much; from former and easier definition practices in the once common underground mines with exposed and available assets, where the obsolete term 'ore in sight' was at least partly literal. But such mines have become rarer, and their underground development less affordable. For most projects, valuations and its definitions have thus been advanced from actual to prospective mines, leaving a very wide gulf between 'what is there' and 'what may happen to it'. This brings the double challenges of reduced geological and technical assurance and the protraction of economic uncertainties.This paper avoids the popular field of regional resources, being confined to what may possibly be mined within single or closely grouped deposits. For these, many estimates of tonnage and grade must be made, defined and declared long before assessment of feasibility; and the uncertainties of the latter make it an unsound base for defining the earlier quantities. Despite the best of intentions, implied or inferred promises may proveimpossible to honour.A simpler framework of definitions is suggested, to some extent reverting to an earlier dependence on supporting work rather than on opinions of economic assurance or future events that are more properly the functions of production and cash flow schedules."

Jan 1, 1994

By M. Celikin, M. Isac, R. I. L. Guthrie, S. Ge

Horizontal Single Belt Casting (HSBC) is a near-net-shape casting process in which molten metal is directly cast into thin strips, at high cooling rates (order of several 100°C/s), with the potential for high volume, friction-free, continuous production of metal strips. This casting process was used in the present work to produce strips of Al-Mg alloys in the AA5000 series, with additions of Sc and Zr. Such aluminum alloys show exceptional potential as a structural material for transportation/aerospace applications. To demonstrate the suitability of the HSBC process to manufacture competitive strip products of Al-Mg-Sc-Zr, the mechanical properties and microstructures of the strips produced using the HSBC process were compared with conventionally cast products. The effects of annealing on the mechanical properties of the strip-cast Al-Mg-Sc-Zr alloys were also investigated.

Jan 1, 2014

By Georges Houlachi, Akram Alfantazi, Maysam Mohammadi

Manganese ions in zinc electrowinning electrolytes form a protective MnO2 layer that ultimately decreases Pb contamination in the zinc product. In this study, the effect of dissolved Mn2+ on the electrochemical performance of Pb, Pb-Ca and composite Pb-MnO2 anodes was investigated. The properties of the MnO2 layer formed on these anodes were studied and compared. Potentiodynamic polarization and cyclic voltammetry experiments were performed in 180 g L-1 sulphuric acid to study the electrochemical reactions occurring on the anodes. The anodes were subjected to galvanostatic polarization at 50 mA cm-2. The morphology and uniformity of the MnO2 layer on the anodes were examined using scanning electron microscopy (SEM). Experimental results revealed that the MnO2 layer formed on the composite anode was more compact and uniform compared to that formed on the Pb and Pb-Ca anode. It was also observed that the cell mud formation rate, and consequently manganese ions consumption, depended on the anode type. Although initial formation of the MnO2 layer decreased the oxygen evolution overpotential, its growth might negatively affect electrocatalytic activity of the anodes.

Jan 1, 2014

By Gonzalo Mato, Colin Godwin, G. Ditson

"The mid-Cretaceous Seagull batholith intruded Mississippian sedimentary and volcanic rocks and Jurassic(?) granitic and ultramafic rocks within the Omineca Crystalline Belt in the Yuk on Territory near the British Columbia boundary. Leucoerotic fluorine- and boron-rich granites of the batholith exhibit many textural variations from aplite to pegmatite, but are dominated by a coarse-grained seriate unit and a fine-grained porphyritic unit.Four distinctive tin vein occurrences within and near the batholith are described, the most interesting of which is the MC showing of quartz-calcite-chlorite-cassiterite veins in intensely fractured zones of sedimentary and volcanic rocks. Three other showings occur within the batholith:J) the EC showing of quartz-fluorite-cassiterite-sulphide veins with prominent muscovite-illite alteration;2) the DU showing of quartz-hematite-fluorite-sulphide- sulphide-cassiterite with considerable manganese staining and sericitic alteration; and3) the VAL showing of quartz-tourmaline-cassiterite-fluorite-arsenopyrite veins with little associated alteration.Most cassiterite occurrences are within easterly-trending, vertical structures and all occurrences are thought to represent parts of a single system. These mineralogical and physical variations are apparently related to the distance from the upper contact of the batholith.For the Seagull batholith, Rb-Sr isotopic data give a 100±1.4 Ma isochron age that is concordant with the K-Ar model age from biotite of 101±4 Ma. Initial Sr isotopic ratios for the batholith are high at 0.712, indicating an old, sialic crustal source for this pluton. This initial ratio is similar to values for granitic rocks associated with tungsten deposits in the Yukon Territory. The high initial ratio for Sr, the high Si02 content, the high s/I index, the presence of normative corundum. leucogranitic composition and associated lithophile-tungsten mineralization demonstrate that the Seagull batholith is probably an S-type granitic body. This factor is significant to regional exploration jar tin and tungsten in the Canadian Cordillera."

Jan 1, 1983

By J S. Kermeen

This paper deals with drilling and blasting techniques at the Phoenix mine, near Grand F1nks, B.C., which is now operated by The Granby Mining Company Ltd. The difficulties of open-pit mining through former underground workings are unique to this operation. Rock types are related to drilling conditions, and the methods used, or contemplated, to overcome the several difficulties are outlined. The equipment used is also mentioned. Finally, blasting techniques and costs are reviewed. Introduction T HE Granby Mining Company operates on open-pit copper mine and concentrator at the site of the original Phoenix mine, near Grand Forks in south-central British Columbia. The pit is a side-hill cut measuring approximately 1,000 by 2,000 ft., and covering a vertical range of from 4,550 to 4,950 feet above sea level. The mill is currently operating at 1,900 tons per day. A 4.5 to 1.0 waste to ore ratio necessitates the removal of some 15,000 tons of ore and waste per working day. Mining conditions at Phoenix are extraordinary in that all the ore zones currently being

Jan 1, 1965

By Å. Partapuoli, M. Henriksson, P. Wikström, J. Worth, G. Adolfsson

The control of AG mills fed by ores with harder and softer components can be challenging due to the sensitivity of the mill to the ratio of hard to soft components. The mills at LKAB’s iron ore operations are generally well controlled, but there are periods when the throughput falls off dramatically, due to a loss of mill filling. As the ore is upgraded in the sorting plant through magnetic separation prior to milling, this presents an opportunity to manipulate the feed blend in advance. In order to assess this opportunity, a fullscale mill charge was dumped and assayed by size to quantify the build-up of competent waste in the mills. This was supplemented by pilot and locked-cycle laboratory tests at a wide range of feed blends in order to facilitate the development of an appropriate multi-component AG mill model. This paper reports the experimental campaign requirements and methodologies, as well as the major outcomes from analysis and modelling exercises using the industrial, pilot and laboratory multi-component data.

Jan 1, 2012

By C. Campero, C. Nicolau, L. Pagliero

The Chilean Congress has recently promoted desalination as a solution to meet the mining industry’s growing water demand. However, this rapid expansion of desalination infrastructure comes with trade-offs. This includes a significant energy cost for treatment, as well as socio-environmental impacts on indigenous communities, tourism, fisheries, and the marine ecosystem. This paper advances a regional-scale model for analyzing competing trade-offs through a case study in the Antofagasta mining region of Chile. Through geospatial data analysis in ArcGIS, new desalination infrastructure investments supplying water to mines are overlain with features of concern raised by communities during the environmental impact assessment (EIA) process, such as national parks, fisheries and exploitation areas for benthonic resources. The resultant model provides a test-bed for analyzing the cumulative effects associated with desalination expansion and for investigating scenarios to mitigate negative social-environmental impacts. The model simulates alternative scenarios for desalination locations and pipeline routes according to competing constraints (i.e. to minimize cost and energy constraints while also avoiding ecological and social hotspots). The ultimate contribution of the work is a demonstration of how the proactive adoption of a regional-scale infrastructure planning might have led to different desalination investment decisions. INTRODUCTION Chile represents the largest producer of copper globally, and holds approximately a third of the world’s estimated copper reserves. However, access to water represents a major constraint to industry expansion and creates conflicts with competing water users (Aitken et al., 2016; Côte et al., 2010). Recently, the Chilean Congress has promoted desalination as a solution to meeting the industry’s growing water demand, which is likely to lead to significant growth in desalination infrastructure to support large-scale mining projects that extract freshwater over a rate of 150 l/s1. By most recent projections, the Chilean copper mining sector is set to increase seawater use by 230% by 2029 (Faversham House Group Ltd, 2019). By the year 2015, Chile had 11 projects serving the mining industry and there are at least other 12 planned plants (Cochilco, 2015). While the use of seawater allows continued expansion of the sector without depletion of scarce underground aquifers, it is nonetheless accompanied with important socio-environmental drawbacks. One such challenge with desalination is the associated energy costs, expressed, both economic and environmental (e.g., CO2 emissions). This includes the energy required for reverse osmosis treatment facilities, as well as to pump water to inland regions at high elevations around 3.100 m.a.s.l in Chile. (Dixon, 2013; Knops et al., 2013). Additionally, the impacts of desalinated water use on flotation chemistry are generally poorly understood, necessitating the need for further research into the impacts, both positive and negative (Cisternas and Gálvez, 2018; Liu et al., 2011).

Jan 1, 2019

By Kazem Oraee

Implementing stable final pit walls in open pit mines during the open pit design phase and mine exploitation has become one of the most important concerns of mining engineers in recent years. Failure of mine walls can potentially cause loss of life, roads blocks, and damage to mining machinery, temporarily or permanently halt production at the face and in the worst case scenario, close the mine. Thus, the role of creating stable mine walls is crucial to safety and general operations of mines and any effort to optimize this process has great economic value for mine operators. This paper aims to illustrate the technical aspects of use of the successful presplit blasting method in metal open pit mines. It also shows that using this approach not only increases safety in mines through wall stabilization, but also will boost economic profits by savings in stripping ratio. In this regard, appropriate practical concepts for designing the drilling and blasting patterns and the role of selecting the correct drilling rigs are elaborated in detail through conducting a case study in Chador Malu iron ore mine in Iran.

Aug 1, 2013