Search Documents

By Jeff Smith

Agenda About NORTHPARKES The NEED The INITIATIVE The SEARCH The PRODUCTS The SOLUTION The RESULTS The Northparkes copper-gold mine in Central Western NSW commenced operations in 1994. Copper concentrate is produced and shipped to smelters in Japan, China & India under long term contracts with spot sales to other Asian countries.

May 1, 2006

By William A. Napier

The Mantaro Phosphate Property is located ~ 250 km east of Lima, Peru in the Andean altiplano near the city of Huancayo, Junin District. The Mantaro deposit is a mineralized zone of phosphatic rock currently defined by surface outcrops, trenches and drilling extending over a strike length of more than 30 km and a width of more than 5 km covering ~27,700 hectares. Mineralization is exposed as three roughly parallel exposures (?mantos?) trending in a northwest-southeast direction along the Mancaspico syncline. Estimated mineral resources1 contained in Manto 1 of the Property (4% P2O5 cut-off) as of February 21, 2010, are: Measured 5.548 million tonnes @ 10.8% P2O5 Indicated 33.975 million tonnes @ 9.9% P2O5 Measured + Indicated 39.523 million tonnes @ 10.0 % P2O5 Inferred² 376.265 million tonnes @ 9.0% P2O5 1Tonnes rounded to the nearest 1,000 and grade to 1 decimal place. 2Inferred material reported with no cut-off and an assumed grade. There is considerable potential to expand the resource base. Mantos 2 and 3 of the deposit have been geologically mapped and exhibit surface mineralization widths similar to Manto 1. Given that the deposit is of marine sedimentary origin, it is reasonable to infer that comparable grades and depth of mineralization are present within Mantos 2 and 3. Based on this assumption, the potential mineral deposits within Mantos 2 and 3 are estimated to be approximately: Manto 2 425-435 million tonnes @ 9% P2O5 Manto 3 280-290 million tonnes @ 9 % P2O5 These potential quantities and grade are conceptual in nature, there has been insufficient exploration to define a mineral resource and it is uncertain if further exploration will result in these targets being delineated as a mineral resource. However, should such conceptual resources be confirmed by trenching and drilling, the Mantaro Phosphate Property would rank as one of the most significant phosphate deposits in the world.

May 1, 2011

By P. L. Claessens, S. Belisle, C. Bowen

"Use of zinc shot feed is a well-established procedure among North American electro-galvanizers. This form of zinc is easy to handle and relatively inexpensive when compared with zinc oxide. This paper reports results on the kinetics of zinc shot dissolution in traditional pure zinc solutions and in electrolytes used for the plating of nickel/zinc alloys. Despite the cementation of minor amounts of nickel in the latter solution, acceptable dissolution rates of the zinc shot can be achieved through proper adjustment of the solution velocity. Under these conditions, the nickel shell produced by cementation is continuously abraded, exposing the underlying zinc.IntroductionThe use of insoluble, noble metal-containing anodes rather than soluble zinc anodes for the operation of high current density electro-galvanizing lines has gained almost universal acceptance. Two major reasons for this trend are:• improved control of the process by virtue of constant inter-electrode distance; and• increased productivity because the operation of the lines does not require the relatively frequent interruptions for replacement of consumed anodes .The results of the principal anode and cathode reactions are, respectively, depletion of the zinc content of the electrolyte and the increase on its acidity;"

Jan 1, 1991

By Robert B. Parsons

"Effective January 1, 1990, mines in British Columbia are subject to a new provincial mining tax statute, the Mineral Tax Act. Under this Act, mines are subject to a two-tier tax system, with a minimum tax payable on ""net current proceeds"" and a higher tax paid on net income. For many mines, the present value of tax paid under the new rules should be comparable to the amount paid under the old rules. Earlier cash payments could pose difficulties, particularly for smaller mines, but existing producing mines could benefit in the short-term.IntroductionEffective January 1, 1990, British Columbia has replaced the provincial mining tax regime under the Mineral Resources Tax Act with a new system under the Mineral Tax Act. The new rules borrow some ideas from other provinces (New Brunswick's two-tier concept, and Saskatchewan's indexed costs) with a view to levying a tax that is fairer to both the producer and the province."

Jan 1, 1990

By Nirmal Weerasekara, Lian X. Liu, The University of Queensland, Weiguo Xie, Benjamin Bonfils, Ping Yu

A mill model structure based on the population mass balance framework incorporating breakage characteristics, slurry and solids transport, product classification and discharge and energy consumption was reported in XXVII IMPC and named the Generic Tumbling Mill Model Structure Version I (GTMMS I). In this work, a new 4D (four dimensional) appearance function sub-model based on the experimental results of the JK Rotary Breakage Tester (JK RBT) was developed to describe the breakage characteristics and was applied to this new model structure. The newly developed 4D appearance function model has fewer fitting parameters and is more generic in nature. Most importantly, it is applicable to both high and low energy impact breakage. It is therefore much more versatile in comparison to the existing JKMRC t10- tn appearance function and the size-dependent JK M-p-q t10-tn appearance function. In addition, the Discrete Element Method (DEM) energy distribution model was integrated into the new model structure. With DEM results providing energy distribution information inside the mill directly, the selection function and the back-calculation method used in the existing JKSimMet modelling method are not needed in this model structure. With the above two revolutionary innovations, the previous model structure was upgraded to the Generic Tumbling Mill Model Structure Version II (GTMMS II). Furthermore, the new model structure is dynamic in nature with time-stepping technique for non-steady-state simulation. A case of the dynamic grinding of a SAG mill was studied to validate the GTMMS II. The model simulation results agreed well with the plant data. With the newly developed 4D appearance function model, the incorporation of DEM energy distribution and transport function, the GTMMS II is an important step forward towards mechanistic modelling of tumbling mills.

Jan 1, 2016

By Tim Mann

"Like other operating mine sites, Placer Dome Inc. - Campbell Mine has taken important steps over the last few years to address environmental issues.This paper will provide specific insights into the implementation of an environmental management system at Campbell. In particular, it will focus on how Campbell developed its plan of action; the lessons that have been learned; the over-all steps that are being taken to enhance environmental stewardship and effectively manage relationships with key stakeholders.IntroductionThe development of an Environmental Management System at Campbell Mine has been part of a general development in management practices which has taken place at the mine during 1990. This paper will discuss the components of the management system in the topic areas of: direction setting; environmental organization; issue assessment; emergency response plan; training ; monitoring/verification; reporting and data management; and relationship management.Although this paper focuses on environmental management systems, the development of this system has partly been a function of responses to other issues which have been addressed concurrently with environmental concerns. These other issues include development of operations management, human resources practices, and safety management practices at the mine. As the Environmental Management System developed, various stakeholders associated with local environmental concerns were identified. This group of stakeholders include the local community; municipal, provincial and federal governments; government agencies; Campbell employees; and the Placer Dome Inc. Corporation."

Jan 1, 1991

By T. E. Smith

"This paper describes the application of a motor-driven flywheel unit, known as a peak shaver, to compensate for the cyclic load fluctuations of a large electric dragline installed at Pine Point Mines, near Great Slave Lake in the Northwest Territories. Of particular interest in this application is the fact that the power system supplying the dragline is a relatively small isolated system, with the major generating source approximately 170 miles from the mine.The cyclic load fluctuations of the dragline are theoretically capable of producing a maximum swing of up to 11 megawatts, which approaches nearly 50% of the installed generating capacity. To reduce these load fluctuations to acceptable limits various alternatives were considered, leading to a decision to install a peak shaver to optimize the operations of both the mine and the power system. Without the peak shaver, the dragline operations would be severely curtailed and additional diesel generation would have to be run at considerable expense, otherwise the power system frequency fluctuations would be totally unacceptable. With the peak shaver, power and frequency fluctuations are kept within tolerable limits, and optimum economic operation of the diesel generation is obtained.The paper outlines the steps leading to the selection of the peak shaver as the compensating device, describes the equipment installed and gives details of operating experience with the dragline/peak shaver combination since installation early in 1979. This .peak shaver is the first of its kind in North America, the only other peak shaver installation being in Australia.IntroductionPine Point Mines Limited owns zinc-lead mining and milling operations located at Pine Point, Northwest Territories, 5 miles south of Great Slave Lake (Fig. I). The company is staffed and managed by Cominco Ltd., which has a 69% interest in Pine Point Mines.Mining activity in the Pine Point area was first recorded in 1898, when the Yukon gold rush was on, but when the zinc/lead showings in the Pine Point area did not yield much in the way of gold, interest in the area soon waned. Cominco Ltd. first acquired some claims in the Pine Point area in 1928, but interest was sporadic until the early 1950s, when extensive exploration indicated rich pockets of zinc/lead ore near the surface. Pine Point Mines Limited was formed in 1951, with Cominco acquiring a majority interest in the company."

Jan 1, 1980

By K. Barron

"A computer program is described which will analyze the stability of coal pillars. The extent of the peripheral failed zone and the central elastic core of the pillar, the stress distribution across the pillar and its strength can be determined by a ""sliceby- slice"" analysis technique. The program incorporates a brittle/pseudo-ductile transition point so that a pillar may fail by brittle fracture or pseudo-ductile yield. It is shown that:(i) There is a minimum pillar stress below which fracture cannot initiate; hence there is a minimum pillar strength. (ii) In specific circumstances (narrow pillars) , once fracture initiates at the pillar edge it must propagate immediately to the pillar centre. This unstable situation is called ""catastrophic"" failure and might be regarded as a model of a pillar ""burst "". (iii) For wider pillars, the failed zone ex tends gradually into the pillar as the loading increases until it reaches the pillar centre when the pillar is deemed to have f ailed. This is called the point of ""ultimate"" failure.The critical pillar widths to avoid catastrophic and ultimate failure can be calculated.A hypothetical analysis of five rib pillars is given to illustrate the application and the results obtained from the model. The model is then used to analyze three case histories taken from the literature. The first demonstrates the applicability of the brittle/pseudo-ductile failure criteria for Pittsburgh coal. The second compares the pillar strength formulae derived here with those of Salamon and Munro(13) and Bieniawskiou . The final case history compares the model analysis with field stress measurements in a yielding pillar. In all cases the model results are compatible with the case histories."

Jan 1, 1984

By D. M. Slavich

"In today's operating and investment climate, project evaluation is both more important and more difficult. It is more important because economic and financial analyses of a proposed project provide a basis for judgment of a project's commercial viability by equity participants, lenders and, in some cases, other participants such as off takers and governments. It is more difficult because these analyses must, of necessity, be based on estimates, projections and evaluations which must be made in a period remarkable for its economic and political uncertainty.Project evaluation starts with the analysis of the engineering, commercial and financial information available. Beginning with the preliminary design and capital cost estimates, alternative financing plans can be developed outlining possible sources of funds, terms and security arrangements. Pro-forma financial statements can also be developed, including sources and uses of funds, cash flow schedules, income statements and balance sheets. With these results, various profitability measures can be determined.Subsequently, in an effort to deal with uncertainty, these results can be tested by measuring the impact on project viability and profitability of changes in project and external variables such as product process, mining and processing rates, operating and financing costs, currency exchange rates and other factors.The results are a number of financial projections reflecting different assumptions for key project parameters. The projections can be used to structure the project to achieve the maximum financial performance. Projects, the financial viability and profitability of which can be demonstrated under varying market conditions, will be the most competitive in capital markets."

Jan 1, 1982

By Teresa Sikora

For over 40 years the Institute of Innovative Technology EMAG has specialized in the development of systems and equipment for laboratory and on-line monitoring of coal quality parameters, as well as the implementation of these systems and devices in mines and power stations. Some of these systems, based on advanced radiation detection techniques such as ?-ray backscattering (ALFA-06 and ALFA -06/T systems) or dual energy ?-ray transmission measurement (ALFA-06/2E ash meter), and also the ALFA-06/3E system applying microwave technology for the measurement of moisture, have had numerous applications in Poland. At present, over 100 systems and devices are used in Polish hard and brown coal mines. For over 10 years, EMAG has been specializing in the development of systems and devices, based on natural gamma measurement technology. An on-line ash meter, RODOS and RODOS Ex, based on measurement of natural gamma radioactivity of coal, has been developed and put into operation. This technique has been also used in developing the portable ash meter WALKER and laboratory analyzer GAMMA NATURA. The paper briefly presents features of the above-mentioned devices, their limits and their obtained accuracy, but in particular refers to the laboratory analyzer, GAMMA NATURA, as the first such device in the world, and presents the results of ash and moisture content measurement in hard, brown coals and potassium salts. The possible applications and advantages of the device in coal mines are discussed. The paper also presents the implementation results of the portable ash meter, WALKER, and the on-line ash meter, RODOS, that is used underground in coal mines.

Aug 1, 2013

By Sylvie Poirier

This paper focuses on new developments regarding thermal rock fragmentation applications. The technology consists in a strong burner powered by diesel fuel and air. The thermal reaction, which is created, allows for the enlargement of 125-mm to 450-mm holes by breaking the rock in a spalling effect. It has been used for over 30 years in Russian open pit mining. Following an agreement between Dynamitage T.C.G. Inc. and the owner of the technology, major improvements have been brought to this technology, allowing for the fabrication of a prototype suitable for the Canadian industry. In Russia and Ukraine, thermal rock fragmentation is actually used to drill large diameter holes in surface mining. Upon having acquired a better knowledge of this technology, it seems that it presents a great potential for selective mining in narrow-vein operations, for either surface or underground mining. Rocmec International Inc., a subsidiary of Dynamitage T.C.G. Inc., and Natural Resources Canada are technical partners in the evaluation of the operational parameters and environmental aspects, such as gas, heat, dust and fog emissions. Furthermore, Canada Economic Development is a financial partner in this project. This paper presents the technology and its history. It also reports on the changes brought to the equipment to adapt it to North American environments. A summary of the tests realized since 1995 is provided, along with the main conclusions obtained. The anticipated applications for the use of this technology in both surface and underground environments are described, such as open pit mining, bulk sampling and narrow-vein ore extraction. An estimate showing a comparison between the thermal fragmentation mining concept and the long-hole mining method is presented and, finally, the future developments planned are listed.

May 1, 2002

By M. Saghaeian, R. Hejazi, Sheikhzadeh. V., A. Abazarpoor

"The morphology of iron ore concentrate particles is known to influence several properties of iron ore pellets, including drop number, compression strength, and reduction properties. This study aimed to determine why grinding methods and particle morphology influence green pellet properties. Particle morphology can be directly related to the grinding method: ball mill (BM) or high pressure grinding roll (HPGR). In this research, two iron ore concentrates, namely Gol-e-gohar and Ardakan, were ground by a BM and HPGR to produce a suitable Blaine value for pelletizing (nearly 1,900 cm2/g). Morphological features of particles were subsequently investigated by sieving and cyclone sizing for particle size distribution, the Brunauer-Emmett-Teller (BET) and Blaine methods for specific surface area (SSA) and scanning electron microscopy (SEM) for the evaluation of shape descriptors. It was concluded that HPGR resulted in generating a greater proportion of fine particles compared to ball milling. The BET results showed that the SSA of HPGR pellet feed was higher than that from the BM due to a greater proportion of cracks, indents and bulges and the creation of new fracture surfaces. SEM images processed by ImageJ software indicated that particles ground by the BM tended to be more rounded and less elongated than HPGR particles because of the breakage model of each method. To show the effect of morphology on the green pellet quality, green pelletizing was performed in a pilot pelletizing disc. The HPGR pellet feed had a higher drop number in comparison to the BM pellet feed, due to the angular and rough shape of the particles.INTRODUCTIONThe demand for fine or ultra-fine particles as feed material for ceramics, composite materials, and mineral processing is on the rise (Kotake, Kuboki, Kiya, & Kanda, 2011). The final concentrate of iron ore processing plants (filter cake) has a size range roughly between 0 and 300 µm, depending on the liberation of Fe containing particles (Meyer, 1980). In general, to produce a suitable pellet feed of appropriate quality, Blaine numbers of 1800–2000 cm2/g should be achieved (Van der meer, 2015)."

Jan 1, 2016

By Dean Gerhardt

Why the need for proactive loose detection? ?? Past history of ground falls in Saskatchewan mines prompted research into new techniques for ground control. ?? Traditional tools for ground assessment (i.e. visual inspection, sounding with scaling bars) are not proactive and can often be time consuming. ?? Need existed for a system that was non-evasive, time efficient, and could be managed by a single operator. Ground Penetrating Radar (GPR) immerged showing the greatest potential.

May 1, 2008

By P. A. Studemeister

"A trondhjemite stock intrudes a volcanic sequence that has massive sulphide lenses and that is metamorphosed to the greenschist facies at Gutcher Lake, 25 km north of Wawa, Ontario. The stock is 4 km2 in plan and is partly enveloped by an aureole of chlorite-epidote-amphibolehornfels up to 1 km wide. Within this contact aureole, biotite is partly pseudomorphosed by chlorite;epidote and hornblende are mottled by chlorite, calcite, plus quartz; albite has 0% An to 8% An; and hornblende porphyroblasts have actinolite rims. The stock has chlorite pseudomorphous after biotite; and feldspar is mottled by white mica plus calcite and has a clear rim of albite. Fractures filled with quartz, calcite, ankerite, chlorite, white mica, pyrite, and native gold cross-cut the stock and its hornfels aureole. These gold-bearing veins are enveloped by foliated rocks with quartz, calcite, white mica, and chlorite that grade outward from the veins into trondhjemite or hornfels.The stock, emplaced into a submarine volcanic series, emanated heat that caused seawater to convect and formed a contact aureole of hornblende hornfels. The stock eventually intruded its aureole and this culminated with regional metamorphism to the greenschist facies. Regional metamorphism hydrated the stock and its hornfels aureole. Native gold precipitated with quartz along fractures from metamorphic flu ids in response to cooling and wallrock hydration. exploration for this type of gold deposits should focus around felsic intrusions that have albite and that have contact aureoles retrograded by regional metamorphism."

Jan 1, 1985

By Jacque Turgeon, Gontran Foy

"The Mineral Research Centre of the Quebec Department of Energy and Resources has worked extensively on the development of a dry process to extract pure mica flakes from a phlogopite ore. The liberation of mica from the gangue is effected basically by impact crushing, and the ground ore is screened into several fractions, each having a fairly narrow range of grain size. Each sized fraction is then fed to an air separator where heavy grains are separated from light flaky grains. Heavy fractions are returned to hammer mills where gangue minerals are ground finer and blocky mica particles are exfoliated. A second stage of screening is performed and each fraction is sent to an air separator. This sequence is repeated until mica products are virtually free of gangue. These different fractions are then treated in a cage mill in which mica flakes undergo a more orderly exfoliation along cleavage planes. The ground mica is again submitted to a final screening stage, after which each fraction constitutes a final commercial product.This process permits the recovery of about 70% of the mica contained in the ore. The over-all process will be described along with technical details of each unit operation. Recent work on a wet grinding method to produce very fine mica will also be discussed.IntroductionRecords of production of mica in Quebec date back to 1886. Production has been more or less continuous since that time, with peak activity during the war years. Production was interrupted in 1966, but started again in 1972 when Marietta Resources and Laviolette Mining and Metallurgical Corporation started their joint operation in Canton Suzor, northwestern Quebec. Mica deposits of more or less importance exist in different parts of Quebec, of which three have attracted attention in recent years: the Canton Suzor deposit, the Canton Lamy deposit and the Canton Chasseur deposit. The Suzor orebody was first identified by Carl Faesler in 1936, who described the rock as ""brown biotite in flakes half an inch in diameter, with interstitial augite, apatite and feldspar""."

Jan 1, 1982

By J. L. Barton, R. A. Murray

"This paper looks at how Syncrude Canada Ltd. is utilizing the Conveyor Belt Monitoring technology developed and patented by the Australian CSIRO and licensed to Syncrude by Conveyor Belt Monitoring of North America, Inc. The technology involves magnetizing the steel cables in the conveyor belts and detecting the fields produced by breaks, gaps or cable ends using special sensors which feed the signals into a multi- channel recorder to provide permanent traces of the various events taking place in the steel cable belts.The data is analyzed and combined with existing belt audit programs, to assist in predicting belt life, change-out criteria and belt design, belt loading and construction. All of these applications of the CBM technology leads to better utilization of resources and forms an integral part of the conveying system reliability program."

Jan 1, 1992

By Alf Hartling

"Most of the Paleozoic section of the Williston Basin is a thick accumulation of numerous carbonate to evaporite, shallowing upward, cyclic sequences. These sediments were deposited in broad epeiric seas, and the deposition of the evaporite facies marked the final stage of each cycle. Many of the sequences display a pervasive replacement dolomite in the uppermost portion of the carbonate units. This secondary dolomitization is, at least in part, an early diagenetic event, synchronous with evaporite deposition.The inception of evaporite precipitation resulted in the seepage of a dense, Mg-rich brine into the underlying sediment. The heavy brine moved down the gentle regional dip displacing the more normal marine interstitial pore fluid and dotomitized the primary calcitic sediments en route. The supply of Mg-ions decreased away from the source, and correspondingly, the degree of dolomitization decreased and larger crystals formed because of slower nucleation at fewer sites.The seepage refluxion of dolomitizing brines gave rise to the frequently observed textural variation of cryptocrys talline, impervious dolomite grading into a finely sucrosic, permeable dolomite down-dip. This diagenetic facies change provides the critical up-dip barrier for potential hydrocarbon reservoirs. The lateral pool boundaries are controlled by either structural relief or a similar diagenetic facies change. The reservoirs are capped by the tight evaporites.Hydrocarbon production is attained from diagenetic traps in the Mississippian Oungre Zone and the Ordovician Red River 'C' Zone . Reservoir creation and the pooling mechanism are the result of dolomitization by the seepage refluxion of dense, Mg-rich brines beneath restricted, hypersaline lagoons. When formulating an exploration/ exploitation program for these oil prone horizons, it is essential to understand the complete geological history in order to establish where the reservoirs will be found and to define the areal extent of each accumulation."

Jan 1, 1984

By D. M. Maijer, S. L. Cockcroft, A. B. Phillion, P. Fan, C. Reilly, H. Khadivinassab

A combined experimental / numerical approach is proposed to investigate the bulk transfer of solute due to liquid metal feeding during shape casting of aluminum alloy A356 (Al-7Si-0.3Mg). A dumbbell-shaped experimental casting geometry has been developed, which promotes solute redistribution due to liquid metal feeding. The redistribution of solute in trial castings is evaluated based on the area fraction of eutectic phases. In the numerical model, silicon species segregation during solidification are calculated assuming the Scheil approximation, and are coupled with macro-scale solute transport due to Darcy flow in the mushy zone and feeding flow. The model has been implemented within the commercial CFD software, FLUENT, which simultaneously solves the thermal, fluid flow fields and species segregation on the macro-scale. The experimental and numerical results are compared and contrasted to examine the effects of liquid metal feeding in this casting.

Jan 1, 2014

By F. Hassani, J. Peck, D. J. Lucifora

The performance of a rotary blasthole drill is heavily dependent on the material being drilled. This material is a microcosm of the in-situ geology that makes up the surface mine in which the rotary blasthole drill is deployed. The performance metrics that are influenced by the in-situ geology are penetration rate (distance drilled per unit time), rotary torque and to a lesser extent rotary speed and vibration. For simulation and testing purposes it is useful to have a validated plant model based upon the application of study. Once validated, a plant model can be used to perform simulation based testing as a supplement and possibly in place of more expensive and logistically complex field testing. Previous studies in the field of rock mechanics have supplied proven models that relate the performance of a rotary blasthole drill to the material being drilled for a given rock type with a given drill bit. In this study, field based experiments were conducted in an active surface mine on a working rotary blasthole drill and the corresponding monitoring while drilling (MWD) data was recorded. Data analysis was then performed on the collected field data. The techniques used successfully fit the collected MWD data to the previously proven rock mechanic models. This paper explores the theory relating rotary blasthole drill performance to the material being drilled, illustrates the required data collection and data analysis techniques, and demonstrates the ability of these techniques and the known rock mechanic models to provide a simulated plant model for the drilling process that can then be validated. This validation is also discussed.

Jan 1, 2015

By Bétournay. M. C.

Advantages ?Safety ?Health ?Rapid, continuous development, productivity ?Stope dilution reduction Disadvantages ?High cost and long time for equipment development ?Hard rock mining condition limitations ?Size of equipment ?Equipment set-up time, down time ?Performance does not meet financial return targets ?Drill and blast retains advantage in cost, productivity, capital investment, application flexibility ?Stress accumulation issues in deep mining, ground support and material handling issues in weaker rock

May 1, 2009