Search Documents

By H. J. McQueen

Aluminum was hot worked at 400 - 500°C and strain rates (e ) of 0.004 -0.1s-1, under reversing strains (c) of 0.5 to 0.2 or 0.5 to 0 and also advancing from 0.5 to 1 or 0.5 to 5. Under similar test conditions for different parts of the strain paths, the average measured flow stresses are found to agree with each other. In the forward and backward strain path tests, the almost identical steady state plateaus affirm the occurrence of dynamic recovery (DRV). On reversal of strain direction at constant e , there was generally negligible Bauschinger effect. In specimens annealed at 400°C, static recrystallisation (SRX) was followed microstructurally. mainly by disappearance of elongated grains with serrated boundaries because the new grains were only little a finer than the old due to low strain energy. The only influence of reversing strain path observed was the effect of change of grain boundary area as grains elongated or returned towards equiaxed. In optical microscopy, elongated grains with serrations and deformation bands confirmed DRV in forward path specimens. In reverse path specimens, equiaxed grains were gradually restored with retention of serrations and bands. In low magnification polarized optical microscopy, grain alignment increased with strain for forward path specimens; whereas it decreased in reverse path ones, supporting DRV. Orientation imaging microscopy (OIM/SEM) revealed that elongated grains are broken up as deformation bands rotate during the forward path and that grains return to equiaxed appearance on backward straining. Comparative studies using optical microscopy in polarized light (POM), OIM/SEM and transmission electron microscopy (TEM) revealed that while subgrains remain equiaxed and constant in size and character during the forward and backward paths, the fraction of low angle facets decreased while that of high angle grain facets increased with increasing strain; these are coupled with a fairly low fraction of medium angle boundaries. The results contribute to the understanding that dynamic recovery in aluminum maintains sub-boundaries with low misorientation but as grains elongate and more subgrain become adjacent to grain boundaries the fraction of high angle boundaries rises (with backward straining it was vice versa).

Jan 1, 2007

By Hong Zhong, Shuai Wang, Fangxu Li, Guangyi Liu

"The flotation performances and adsorption mechanisms of a-hydroxyoctyl phosphinic acid (HPA) to malachite, cassiterite and wolframite were investigated by micro-flotation tests and X-ray photoelectron spectroscopy (XPS) analyses. The micro-flotation results indicated that compared with styrene phosphonic acid (SPA), diphosphonic acid (DPA), benzohydroxamic acid (BHA) and salicylhydroxamic acid (SHA), HPA exhibited excellent collecting power to the three oxide ores. In addition, HPA showed superior selectivity against hematite, tourmaline, feldspar and quartz. The results of XPS analysis demonstrated that HPA reacts with active species (M) on metal oxide by formation of P-O-M or P-M bonds.INTRODUCTIONIn mineral processing, flotation has been the main process for separation and recovery of valuable minerals from complex ores (Mei, 2013; Zhou, 2014). One of the key requirements in flotation process is to increase selectively the surface hydrophobicity of the targeted minerals by surfactant (known as collector in flotation) adsorption so that these mineral particles can preferably attach air bubbles in a slurry or pulp (Bai, 2004; Hankins, 2004). To anchor a solid surface selectively, special functional group are designed to adjust the interaction between the surfactant and the active sites of solid surfaces (Wu, 2006; Huang, 2014).Organic phosphorous compounds have strong affinity toward metals or metal oxides because they form more stable metal complexes than metal carboxylates (Pazik, 2001; Zheng, 1998). In mineral engineering, phosphorous compounds have been exploited as metal extractants and flotation collectors (Alguacil, 2002; Sun, 2008). Ni (2012) and Zhang (1998) introduced diphosphonic acid (DPA) as an effective collector for flotation of fersmite and niobite. Liu (1999) found styryl phosphonic acid (SPA) was a superior collector for flotation recovery of finely disseminated rutile ores. Gruner and Bilsing (1992) thought SPA was one of the best collectors for flotation recovery of cassiterite which could obtain a high-grade concentrates of more than 40% with high recovery values. Bulatovic (1999) investigated the flotation performances of phosphoric acid ester (PAE) to perovskite, ilmenite and rutile and found that PAE was an impactful collector for selective flotation of titanium minerals from complex ores in the presence of petroleum sulfate. However, a-hydroxyoctyl phosphinic acid (HPA) as a flotation collector for recovery of titanium ores were hardly reported in the previous literatures."

Jan 1, 2016

By S. Harvey

The McArthur River deposit is a structurally-controlled unconformity-related uranium deposit. The mineralization is situated at the intersection of a pronounced fault zone, referred to as the P2 fault zone, and the unconformity between Paleoproterozoic Wollaston Group metasedimentary rock and Paleoproterozoic to Mesoproterozoic Athabasca Group. Mineralization is variably hosted within the Athabasca Group fault wedge and the faulted basement, consisting of twelve zones covering a strike length of 2,700 m. The main P2 fault zone consists of several reactivated foliation-parallel faults containing narrow seams of graphitic clay gouge that are separated by highly cleaved, graphitic wall rock. The mine grid east-dipping P2 fault zone is characterized by reverse offset of the unconformity surface. It varies from a single discrete fault to splay offsets consisting of two to three individual splays. The combined vertical offset along the P2 fault zone is a maximum of about 80 m. The fault has emplaced a wedge-shaped sequence of Wollaston Group metasedimentary rocks into the Athabasca Group. Foliation-oblique faults occur throughout the McArthur deposit trend. Steep east-northeast trending faults generally exhibit apparent oblique dextral sense of shear. Less common, and possibly conjugate, are steep faults trending east-southeast with an apparent sinistral sense of shear. Offsets are generally less than 10 m on these structures. South-trending and shallow west-dipping brittle faults with offsets less than 1 m are also observed while rare steep, north-trending faults are also noted locally and played a critical role in development of the Zone 2 basement-hosted mineralization.

Jan 1, 2020

By R. I. Kraydenko, A. N. Dyachenko

"The possibility of SiO2 5N production by staged purification of ammonium hexafluosilicate (NH4)2SiF6 is discussed. High-purity silicon dioxide can be obtained with fluoridation of quartz concentrate by solid NH4F at 100 °C, with further sublimation of the product at 320 °C, its dissolution, ammonia hydrolysis, filtration and drying of SiO2•nH2O. This is accompanied by regeneration of the processing reagent - NH4F.INTRODUCTIONProduction of high-purity silica-5N (SiO2 content over 99.999%) is an important and urgent task of the modern chemical industry. This material is used in the manufacture of optical glass, optical fibers for internet cables, silicon for solar power and electronics.Quartz concentrate is raw material for the production of silicon dioxide. The existing technologies of synthetic silicon dioxide were introduced in the mid-twentieth century. These methods are energy-consuming, multi-step and do not meet stringent environmental requirements. In fact, as some conventional technologies became obsolete; it became necessary to develop new methods for the production of synthetic silica. We believe that the fluoride technology of processing of quartz materials by ammonium fluoride is the most promising direction.In industry, silicon dioxide marked ""Silica White"" is obtained by liquid-phase method. The method consists of the precipitation of amorphous silica from sodium silicate solutions with acids. The resulting product is filtered, washed and dried. Depending on the deposition conditions and nature of the coagulant the ""Silica White"" is acidic, neutral or alkaline. The dry product is subjected to grinding. The degree of dispersion and porosity of the particles of Silica White depends on the nature of decomposition agent (a substance that decomposes the silicate) and coagulant, conditions of sedimentation, filtration and drying. During the drying process the silica particles are sintered into aggregates of a few millimeters."

Jan 1, 2012

By D. C. Carter, J. P. Anderle

"Exploration drilling of evaporite sequences in eastern Canada has undergone significant changes in equipment, techniques and philosophy since the early 1970s. The result has been the recovery of full-size cores from properly conditioned and stabilized holes, high quality open hole geophysical logs, and high quality metallurgical samples. The majority of modifications have resulted from the necessity to preserve the integrity of the evaporite deposit, and thus ensure the potential development, combined with the need for cost-effective high quality information. This is particularly evident in the priority placed on the development of non-erosive drilling fluids, casing and cementing procedures. The results are applicable to diamond drilling exploration of evaporite deposits anywhere in the world.IntroductionThe majority of current technical and scientific literature and expertise available on such subjects as drilling fluids or cementing procedures is applicable to large diameter, deep (several thousand metres) oil-field type drilling . The differences between oil-field drilling and wire-line core diamond-drilling are dramatic: large diameter, deep holes drilled with a low rpm tricone bit using large volumes of fluid pumped through a large annulus versus small diameter, shallow (less than 600 m) holes drilled with a high rpm diamond-set core bit using small volumes of fluid pumped through a small annulus. Exploration drilling of evaporite sequences in eastern Canada in the early I970s was conducted using oil-field equipment and techniques to complete holes of moderate (1000 m to 1500 m) depth . The prohibitive cost of these operations has necessitated that subsequent exploration drilling employs modified diamond-drilling equipment and techniques developed as part of a transition away from oilfield methodology. The result has been full size core, recovery approaching 1000/0 and the ability to run open hole geophysical logs; a combination of factors enhancing the collection of high quality information (Carter, I989a)."

Jan 1, 1990

By J. E. Nesset, W. Zhang, J. A. Finch

Frother influences water recovery through control of bubble size and a chemical effect. De-coupling the two is necessary to establish the extent of the chemistry effect. A setup is described to give steady state water overflow rate (Jwo) along with measurements of bubble size into and on top of the froth. Arguing neither bubble size correlates directly with water overflow, a frother mass balance is solved to estimate the bubble surface area flux in the overflow (Sb0 ). The solution required measurement of frother concentration using TOC analysis and frother adsorption density using surface tension data. The relationship between Jwo and Sbo reveals the frother chemistry effect, quantified for discussion purposes by an equivalent water layer thickness.

Jan 1, 2009

By William Ferguson, Claude Deveau, Wade Hazel, Stephen R. Young, Allen Lussier, Robert Copeland

"LocationSometimes known as the Bernie Lake mine, the mine is located about 180 km east-northeast of Winnipeg on the northwestern shore of Bernie Lake, close to the Nopiming Provincial Park and the Manitoba-Ontario boundary. The mine is accessed from Lac du Bonnet which is linked to the provincial road system.Brief Description of OperationTantalum Mining Corporation of Canada Ltd. operates an underground mine employing ramp access, room and pillar mining, and shaft hoisting for the production of tantalum, lithium and cesium minerals. Daily campaigned crushing of the tantalum and lithium ores supply separate concentration circuits. Tantalum recovery employs conventional gravity equipment together with recently developed centrifugal concentration methods. All tantalum concentrates go to Cabot Performance Materials for the production of tantalum chemicals and metal. Lithium minerals are recovered using heavy medium separation and silicate flotation to produce spodumene and montebrasite/amblygonite concentrates. The lithium concentrates are shipped worldwide for use in ceramics, specialty glass and mold powders. Cesium processing involves the dry grinding of pollucite as feed stock for the recently built on-site chemical plant dedicated to tl1e production of cesium formate, a high-density drilling fluid for use in the oil industry."

Jan 1, 2000

By J. G. Whellock, J. W. Matousek

"In spite of their importance to the economics of many metallurgical projects, the values and technical aspects of precious metals losses in smelting operations are relatively undeveloped subjects. This paper attempts to provide a condensed overview of precious metals losses in pyrometallurgy, using some of the limited production and experimental data available. It is intended for three general groups of metallurgists - operators attempting to improve recoveries, cost-accounting engineers making estimates of metal losses in new or modified smelting plants, and research engineers and students.Distribution coefficients of precious metals, the ratios of metal or matte assays to slag assays, are convenient means of comparing smelting processes and the tendencies of the different metals to enter the slag. For silver in lead blast furnaces this ratio is approximately 250;for gold and the platinum group metals in submerged-arc, electric furnaces it is 900. The ratio for gold and PGMs in converters varies with the degree of oxidation of the charge. The over-all cycle-average for industrial installations is tentatively estimated to be 35.IntroductionThe magnitude of precious metal s losses in pyrometallurgical operation s is difficult to assess. The primary producers are generally reluctant to discuss the subject. The by-product producers (the large sulphide smelters o f copper , nickel, and lead) might be more willing to disclose information, but these have precious metals in their feeds in such dilute quantities that accurate accounting is extremely difficult. It is not until numerous processing steps have been taken t hat the precious metals become sufficiently concentrated to permit acceptably accurate sampling and analytical procedures to be followed. Thus, knowledge of the precious metals contents o f the intermediate mattes and slags may simply be unavailable."

Jan 1, 1990

By Syamujulu. M

Subsequent to the unbundling of the Zambia Consolidated Copper Mines (ZCCM) and the privatization of its constituent parts, the Konkola Copper Mines (KCM) represents a third of the original conglomerate. Now run by private hands as a sub group of Vedanta Resources Plc of India, KCM is strategizing on how best to deal with the operational issues of the organisation to resolve some of the difficult, logistical, environmental, mineralogical and metallurgical problems being encountered to tum them into opportunities as the company turns around. This paper reviews the options being put in place to provide appropriate solutions and strategies including the treatment of the highly siliceous low energy copper belt concentrates in its mining operations in Zambia.

Jan 1, 2007

By Hajime Miki, Gde Pandhe Wisnu Suyantara, Tsuyoshi Hirajima, A. M. Elmahdy, Keiko Sasaki

"Seawater has been reported to depress molybdenite in a copper-molybdenum (Cu-Mo) flotation process at high pH due to the precipitation of Mg(OH)2. Meanwhile, to improve mineral recoveries, collectors are usually added into the flotation cells, thus adding the complexity to the mechanism of bubble-particle interactions involved in Cu-Mo flotation. Therefore, understanding the interaction mechanism in seawater flotation and in the presence of collectors is important to explain the minerals depression. The present work investigated the effect of kerosene on the bubble collision and attachment to pure chalcopyrite and molybdenite surfaces in MgCl2 solution as one of the seawater major components at pH 6 and 11. Mineral surfaces were characterized using atomic force microscopy (AFM). In addition, minerals floatability in the same system were tested in a column flotation. The study of bubble-particle interactions shows that following several collisions, bubble could displace the intervening liquid layer on the mineral surfaces, forming a three-phase contact (TPC). A TPC formed more rapidly in the presence of emulsified kerosene in a 0.01 M MgCl2 solution at pH 6 for both minerals. The reason is kerosene increased the surfaces hydrophobicity and destabilized the intervening liquid layer on the surfaces. Moreover, the average time required to form a TPC was shorter on molybdenite surface. This can be attributed to the effect of adsorbed kerosene on molybdenite surface and molybdenite surface roughness.INTRODUCTIONIn froth flotation, bubbles are used to separate hydrophobic mineral particles from hydrophilic particles. In this process, bubble-particle interactions (i.e., collisions, attachment, and detachment) are crucial with regard to mineral recoveries. The effectiveness of froth flotation depends on the formation of stable aggregates between the hydrophobic particles and the bubbles, allowing the bubble to carry the particles to the froth layer. To form such aggregates, the bubbles and particles must collide, and the intervening liquid layer must be drained below the liquid layer critical thickness, forming a stable threephase contact (TPC) (Ralston & Dukhin, 1999). Particles detachment may take place if the particles still have sufficient kinetic energy and the TPC is not formed. Previous studies of bubble-particle interaction in electrolyte solutions have been conducted using atomic force microscopy (AFM) (Assemi, Nguyen, & Miller, 2008), and by approaching the bubble using mica plate (Pushkarova & Horn, 2008), however, these studies did not focus on the bubble-particle collisions. Bubble collisions and attachment to hydrophobic (Teflon) and hydrophilic (glass) surfaces in a a-terpineol solution have been investigated by Krasowka et al. (2003)."

Jan 1, 2016

By F. P. Hassani, A. Hara, M. Momayez

To be competitive on the international market, the Canadian mining industry must reduce its costs, increase its productivity and maintain a high standard of safety. There is a great need today for improved methods that would allow the detection of geological structures in advance of mining to reduce dilution and the monitoring of underground structures to increase safety. This will facilitate planning for optimum exploitation of the mine and to increase production at lower costs. This paper discusses two examples of more efficient mine planning using new technologies such as Ground Probing Radar (GPR). In Kidd Creek mine, GPR technology was used at the 2500and 2600 levels to (1) monitor the stability of the sill pillar; (2) locate the presence of disseminated sulphide pockets in the sill pillar for extracting the mineral content; (3) monitor the stope backs and wall structures to evaluate the effect of on-time filling sequences; and (4)assess rockfill quality in terms of the presence of voids and fractures within the rockfilled areas. In the New Brunswick coal mine in Minto, GPR was used along with core log data to map and construct a 3D block of a section of the bench showing the relative position of different layers overlying the coal seam.

Jan 1, 1996

By F. W. Guernsey

Of all the elements, sulphur occupies a place by itself. It is mined in situ, in such quantities and of such purity that, as regards the tonnage produced, it is the first of any element on the list. Iron and coal the great tonnage producers, are combinations of elements, while sulphur is mined and marketed almost chemically pure. It is sold, in large quantities, commercially, calling for a purity of 99.5 per cent while for medicinal purposes, the Pharmacopoeia requires only 99 per cent. purity. It is a very common commodity, and like many common things is of extreme importance, in the progress of our civilization. The substance has been known from the earliest times, the word sulphur being derived from the Sanskrit Culvari", hence the Latin Sulphur. Commercially it is also called brimstone, this word being a derivative of the Anglo-Saxon Bryne Stane or burning stone. From our younger days, we have been more or less familiar with the mineral. On the spiritual side being threatened, if we did not behave ourselves, with an ultimate consumption in a lake of fire and brimstone, (which in moments of reflexion was not pleasant to contemplate) while our bodily ills were taken care of by inward applications as a spring medicine. In both instances, the effect required, was generally attained. Sulphur occurs in nature, both free and in the combined state, it being estimated that it forms, over one tenth of one per cent of the first ten miles of the earths surface. (I do not know who did the estimating and it is not guaranteed).

Jan 1, 1923

Current AG and SAG mill circuits have continued the trend to larger, fewer mills. These large mills place a significant additional load on the discharge systems and it has become imperative that the designs of these mill discharge systems are evaluated carefully to ensure maximum efficiency and have the capacity to be able to handle the increased mill discharge volumes. The current generation of multiphysics modeling tools allow a detailed analysis of AG and SAG mill discharge performance. The combination of Discrete Element Method modeling and Computational Fluid Dynamics allows the designer to model in detail all aspects of a mill discharge performance. This includes a detailed description of the build-up of solids and slurry in a mill discharge, the recycle of material back into the mill through the grates, the relative wear rates and the occurrence of overloading at the pinch points. These tools allow intelligent decisions to be made regarding the type of discharge arrangement, pan lifter geometry, and discharge cone design, so as to ensure that the discharge is capable of handling the duties required for a specific installation. This paper details the current state of the art in these modeling tools, and provides an overview of some recent applications.

Jan 1, 2012

By Roger Lafrance

"This paper discusses various aspects affected by the use of large-diameter boreholes in underground mines. Topics covered consist of noxious fumes, vibrations, post-blast effects, various types of explosives, the cordine system in production blasts, the slider primer system and wall-control methods. In general, the paper is an overview of this important fact of underground mining.IntroductionWith economical factors leading the way, many reasons motivated drilling equipment companies to develop equipment that can drill holes up to eight inches in diameter and even larger for underground applications. One of these other reasons is the fact that many orebodies were considered marginal, given the high costs of conventional mining methods utilizing small diameter boreholes. With these criteria in mind, accelerated programs were put in motion to develop equipment that would reduce both-development and production costs in underground mines. Change s in any basic program often affect other areas down the line. This is particularly true with the ad vent of large-diameter boreholes underground.C-I-L Inc. is certainly no stranger to this phenomena. Whether production headings increase in size and tonnage or whether production increases due to lower costs, one fact remains unchanged and that is the fact that all development and production holes are loaded and blasted whether they be of small or large diameter. Due to this fact, C-I-L Inc., as a leading explosives manufacturer, initiated a program to examine blasting methods in use in surface work with the intent of revising these method s for underground applications. Research facilities were also oriented toward developing appropriate products. This was a task that was accepted with anticipation, with the result that many new blasting systems and methods were brought forward, thanks to the collective efforts of both the consumers and manufacturers."

Jan 1, 1984

By M. W. Gilmore, J. Ndlovu, T. Sepoloane, Anglo American Platinum, L. R. Nelson, R. N. Varty, L. J. Bryson, B. Peyper, J. P. Hagemann

"As part of Anglo American Platinum’s Rustenburg Base Metals Refinery (RBMR) expansion, a new Nickel Electrowinning Tank House, with a nameplate capacity of 32 400 tons per annum, was constructed. Commissioning of the new electrowinning technology, which involved world first full deposit plating, commenced in 2011.The old nickel electrowinning process at the RBMR used starter sheets which, along with a divided cell configuration, was very labour intensive and exposed operators to high levels of aerosols that contained both nickel and acid. To overcome this problem two key design intents of the new technology are aerosol abatement and minimising labour in the electrowinning cell environment, with a design target to reduce the nickel occupational exposure limit (OEL) to half the legislated limit of 0.1 mg.m-3.Commissioning of the new technologies adopted to achieve mist abatement is described, together with a review of technical and operational challenges relating to the titanium blank edge strips, blank roughness and sandblasting optimisation, blank quality control, electrode spacing, polyconcrete cell dimensional stability and cell top furniture. The impact of these on process performance is presented and the development of fault checking and rectification methods, to maintain high process performance, is explained.INTRODUCTIONThe expansion of Anglo American Platinum’s Rustenburg Base Metals Refinery necessitated the construction of a new Nickel Tank House to achieve two primary objectives, namely increasing the nickel electrowinning capacity from 22 500 tons per annum (tpa) to 32 400 tpa nickel, and a design to reduce the nickel aerosols to 0.05 mg.m-3 as a time weighted average over 8 hours, which is half of the legislated occupational exposure limit (OEL) of 0.1 mg.m-3."

Jan 1, 2016

By Neil Campbell

"The Pine Point area is on the south shore of Great Slave Lake, 510 air miles north of Edmonton and J JO miles south of Yellowknife, N.W.T. The occurrence there of lead and zinc was reported in J 899 by R. Bell (5) of the Geological Survey of Canada, and in the following years several claims were staked and some prospecting was done. In 1928 Atlas Exploration Co. took over the property containing the discovery occurrences. In 1929 The Consolidated Mining and Smelting Company of Canada Ltd. (""Cominco"") and Ventures Ltd. participated with Atlas in forming the Northern Lead-Zinc Co., which, under the direction of J. M. Bell, carried out 24,499 feet of drilling in the discovery and surrounding areas. Two shafts and many surface pits were also sunk. This work showed that the discovery deposits contain about 500,000 tons of lead-zinc ore, but no new orebody was found.In 1936 D. F. Kidd (11) drew attention to the highly significant space relations between the base-metal discoveries at Pine Point and the projections of certain major Precambrian faults mapped earlier by C. H. Stockwell. Geological work by Cominco in 1940 and subsequent years suggested the presence of mineable deposits within a belt of land including part of the area of earlier field work and extending far beyond it. Between 1946 and 1954 exploration financed by Cominco and Ventures Ltd. included 182,950 feet of diamond drilling, 383 feet of sinking, and 240 feet of drifting, raising, and crosscutting. This work was successful in finding substantial quantities of new ore in places where bedrock is completely concealed.The topography is one of low relief, characterized in many places by swampy muskeg and shallow, marl-bottomed ponds. The area where ore has been found is generally higher ground which, though not well drained, is comparatively dry. It is also marked by raised beaches and a few sand dunes overgrown by small spruce and pine. Bedrock is generally overlain by a variable thickness of hard, glacial boulder clay. This in turn is covered by silt, sand, and gravel, probably deposited from the waters of Great Slave Lake, which formerly extended many miles beyond its present southern shore."

Jan 1, 1949

By G. I. Mathieu

"An experimental study was carried out to evaluate the performance of column flotation versus conventional flotation for the recovery of molybdenite from a Newfoundland ore. The objective was to verify the claims made by the inventors of the flotation column, Messrs. Pierre Boutin and Remi Tremblay, that their apparatus reduces the entrainment of fine gangue and other mineral impurities in the froth product. The research included a factorially designed series of tests to determine satisfactory operating conditions of the column. These provided a basis for comparative flotation tests with column and Denver cells. In the course of the work, the action of a few depressants was studied. Results indicated greater selectivity in the column and reduced reagent consumption."

Jan 1, 1972

By L. S. Beck

"IntroductionThe Beaverlodge District is an important mineralogenic province of pitchblende and occupies about 1300 square kilometres centred on Beaverlodge Lake near the north shore of Lake Athabasca in northwest Saskatchewan (Fig. 1). Uranium City is the main settlement of the area and is serviced by scheduled aircraft from Edmonton, some 700 km to the southwest, and from Prince Albert which lies a similar distance to the south.During the summer, boats and barges supply the area from the railhead to Fort McMurray via the Athabasca River and Lake Athabasca, a distance of about 550 km. For the past few years a winter road has been maintained across Lake Athabasca to Cluff Lake to connect with Highway 155.The topography of the area is typical of the Precambrian Shield with generally low relief and a disorganized drainage of numerous lakes separated by hummocky rock ridges, muskeg and drift-covered areas. Local topography in the area is, however, extremely rugged, particularly south and east of Beaverlodge Lake, where resistant rocks form prominent hills and ridges extending as much as 180 m above lake level. Rock exposures are abundant and form over 50 per cent of the land area.History of Exploration and DevelopmentEconomic interest was first aroused by Tyrrell (1896) who described an occurrence of iron formation at Fish Hook Bay; however, subsequent evaluation of the deposit indicated it to be uneconomic."

Jan 1, 1986

Mirador - Overview ? Located in Andean foothills of SE Ecuador ? Copper-gold porphyry hosted by calc-alkaline Late Jurassic granitic and porphyritic rocks ? 438 MT of 0.61% Cu and 0.19 g/t Au measured and indicated resources (at 0.4% Cu cut-off) ? Additional inferred resources of 235 MT of 0.52% Cu and 0.17 g/t Au ? Initial 25,000 tonnes/day production, expanding to 50,000 in year 6 320 MT of 0.62% Cu, 0.2 g/t Au ore mined at an average 1.4:1 strip ratio over a 21 year mine-life

May 1, 2006

By Yves Bellemare

Entre 1983 et 1997, l'exploitation de la pierre de taille au Québec a été marquée par l'émergence et la consolidation de plusieurs nouvelles variétés de granit, provenant exclusivement ou presque de la Province de Grenville. Le Québec demeure toujours le principal expéditeur canadien de granit dimensionnel, avec des expéditions annuelles représentant près de quatre-vingt-dix pour cent des expéditions totales canadiennes de granit brut et transformé. La production annuelle de granit brut oscille, depuis 1994, autour de cent mille tonnes métriques. Cette production a plus que doublé de 63 000 à 140 000 tonnes métriques entre 1981 et 1990, mais elle a connu une chute importante en 1991 (67 000 tonnes métriques); cependant depuis 1994, elle est en forte progression (Ménard, 1998). En 1983, le granit dimensionnel était extrait de plus de vingt-cinq carrières, dont les trois quarts se localisaient dans la Province géologique de Grenville. Comparativement, en 1997, le Québec comptait trente-sept carrières actives, dont trente-cinq dans le Grenville (Gaudreau et al., 1998). Cette concentration des carrières dans la Province de Grenville s'explique par la demande accrue de nouveaux produits au fil des ans et par le potentiel élevé de découvertes de nouvelles variétés dans cette Province géologique. L'accessibilité au territoire, toujours plus grande, a facilité la mise en production de carrières favorisant la diversification des produits. Le ministère des Ressources naturelles du Québec (MRNQ) a consacré depuis 1980, beaucoup d'efforts dans la recherche de nouveaux gisements et de nouvelles variétés. En plus des programmes de subvention destinés aux prospecteurs ou aux compagnies, le ministère a réalisé des campagnes d'inventaire de pierre de taille, de pierre concassée et de pierre d'enrochement pour en connaître le potentiel géologique et à orienter les recherches futures (Nantel, 1983; Nantel et Martignole, 1991; Bellemare, 1995a, b, c, d, e, f, 1997, 1998a and b; Bellemare et Petryk, 1996a, b, c and d). Cette étude donne un aperçu des différentes variétés de pierres extraites dans la Province de Grenville entre 1983 et 1997, les situe dans leur contexte géologique et en localise les principales régions productrices. Elle est une suite à l'article publiée par Nantel (1984).

Jan 1, 2001