Search Documents

By James F. Kelly

"Research and development on the production of liquid fuels from coal is rapidly expanding worldwide. AImost every industrialized country is engaged in coal liquefaction research and process development. In Canada, the federal government, through CANMET, is actively supporting coal liquefaction research and development in a number of areas.A review of the basic principles and some of the processes in the production of liquid fuels from coal is presented with reference to the characteristics of the Canadian coal resource base. An overview of the CANMET coal liquefaction contract program is presented and specific results from the batch autoclave studies carried out with Saskatchewan lignite and Nova Scotia high-volatile bituminous coals are discussed. The development of a laboratory-scale continuous-flow coal liquefaction unit at the Energy Research Laboratories of CANMET to investigate the co-processing of coal and bitumen/heavy oil is also described.IntroductionThe CANMET coal liquefaction program is made up of two interrelated parts. The first part consists of the research and development work being carried out at the Energy Research Laboratories near Ottawa, Ontario. The second focuses on contracted research and development as part of the Coal Conversion Program of Energy, Mines and Resources Canada. The long-term objective of the liquefaction program is to contribute to Canadian liquid fuels production through the definition, research, development and demonstration of different coal liquefaction technologies for the Canadian marketplace.In coal liquefaction, the main objective is to produce liquid hydrocarbons with a higher hydrogen-to-carbon (HIC) ratio than the coal feedstock while reducing heteroatom (S,O,N) content, removing mineral matter and minimizing gas production. Typical atomic HIC ratios for a variety of Canadian fossil fuels are shown in Figure I. Canadian coals have about 500/0 of the HIC ratio present in tar sand bitumens and heavy oils and only about 20% of the ratio available in methane. In general, the cost of synthetic fuels production is related to the cost of hydrogen and, therefore, to the increase of HIC ratio between feedstock and products. On this basis, the production of liquid fuels from coal would be expected to be more costly than liquid fuels produced from bitumens and heavy oils. However, for mined tar sands and some heavy oils this difference tends to be offset by the large sand content (>90 mass %) of tar sand bitumens and the increased production costs of viscous heavy oils. For example, it can easily be shown that for equal weights of distillate <525°C) yield, current coal liquefaction processes required between two and three times less mined coal by weight than the mined tar sand s required for the most technically advanced processes proposed for bitumen upgrading."

Jan 1, 1981

By Earl Gebhardt

"The planning and design of mining panels in the Potash Corporation of Saskatchewan Inc., Lanigan Division mine Block B involved a number of investigative techniques. The techniques utilized to gain insight into the viability of mining included2-D and 3-D seismic surveys, longhole drilling, exploration wells, photo lineament, magnetic and gravity surveys, and actual room excavation.IntroductionPotash Corporation of Saskatchewan Inc. (PCS) owns and operates four potash mines in the province of Saskatchewan. The Lanigan Division mine is located 110 Ian east of Saskatoon, Saskatchewan, near the town of Lanigan.The Lanigan Mine commenced production in August 1968under the ownership or Alwinsal Potash of Canada Limited. The mine was purchased by PCS in 1977.Lanigan Division&apos;s productive capacity is 3.4 million tonnes of product per year. Ore is extracted from the "" B"" zone or Layer III or the Patience Lake member of the Prairie Evaporite, more than 1000m below surface . The Patience Lake member (approximately 20 m thick) consists of potash interbedded with salt. The average run-of-mine ore grade is 21070 K20 (Fig. I).The mine was initially developed using the room-and-pillar technique. Improvements in mining resulted in the use or extensible conveyors in long panel rooms."

Jan 1, 1993

By L. J. Bryson, C. A. Biley

"Anglo American Platinum’s Rustenburg Base Metals Refiners (RBMR) produces Ni and Cu cathode from slow cooled converter matte after Platinum Group Metals (PGMs) are magnetically separated for further processing. In 2010, execution of the RBMR expansion project was commenced to increase the production capacity to 33 ktpa Ni. The expansion, which is currently still in a ramp-up stage, brought about several fundamental changes to the circuit chemistry, including the installation of a dedicated Pressure Iron Removal (PIR) autoclave. This provided an independent outlet for iron from the refinery, which previously deported to the residue from the leach circuit and was toll refined. At the same time as changes in the circuit associated with the RBMR expansion were being made, the plant experienced a significant increase in iron and copper units per nickel unit in the feed. The decoupling of the leaching and iron removal process steps has had significant advantages for the robustness and control of the overall circuit, in particular pertaining to the preparation of a nickel electrolyte of sufficient purity to produce LME grade nickel. This paper details the primary changes to the RBMR circuit chemistry with a particular focus on iron deportment and the benefits derived from the installation of the PIR autoclave.INTRODUCTIONAnglo American Platinum mines and refines Platinum Group Metals (PGMs) through a complex processing pipeline in its South African operations. Mined ore is first treated through several mineral processing stages, geared to the recovery of base metals and associated PGMs, followed by smelting and refining operations that aim to separate base metals from PGMs and recover the value components to purified, saleable products. The focus of this paper is the Rustenburg Base Metals Refiners (RBMR) complex which receives a PGM-containing converter matte, then physically separates PGMs and base metals, and recovers nickel and copper to cathode by utilising leaching, precipitation and electrowinning processes.With new mining operations coming online and the continued increase in PGM ore arisings, it was necessary to undertake an expansion project at the Base Metal Refinery (BMR) to increase production capacity from 21 ktpa to 33 ktpa Ni. Complicating the expansion project was the requirement of continued production through all stages of design, construction and implementation and, due to stringent capital constraints, the utilisation of all existing equipment installed during a previous expansion in 1981. Against this backdrop, the expanded BMR flow sheet involved significant changes to the chemistry, especially iron management. These changes in iron management allowed for the separation of iron and copper residues and significantly increased the robustness of the plant to changes in feed mineralogy as well as the potential to increase production duties of the existing equipment."

Jan 1, 2016

By Y. -H. Cho, J. -M. Lee, J. -G. Jung

The effects of copper on the microstructure and mechanical properties of ultrasonic melt treated Al-xCu (x=0, 4) alloys were investigated. The densities of alloys were increased and their grain sizes were decreased by UST. The hardness and electrical resistivity measurements revealed that the amount of solute Cu within Al matrix was increased by UST. Both the yield and tensile strengths of Al-4Cu alloy were increased by UST. The improved mechanical properties of Al-4Cu alloy by UST were probably due to the reduced amount of casting defects (e.g. pore), grain refinement, and enhanced solid-solution hardening of Cu.

Jan 1, 2014

By J. M. Wetherill

"This paper presents the results of an investigation into the level of radon, as against the natural background, at the Vicary Creek coal mine in Alberta. The concentrations of radon and daughter products detected in the mine were considered to be insignificantly higher than the concentrations of naturally occurring radon and thus do not constitute a health hazard to the miners.INTRODUCTIONTHE HIGH INCIDENCE OF LUNG CANCER among miners exposed to radon was established some thirty years ago. The presence of this gas in mines is primarily associated with pitchblende extraction operations, al-though coal contains detectab`e quantities of U30s. A previous study bas shown that coal from southwestern Alberta (Exshaw and Banff) contains lower than average concentrations of this element (1).As part of a general investigation into the occupational health environment of coal miners in Alberta, field measurements were made to establish the level of radon and to investigate the natural background radiation in the Vicary Creek coal mine, located some 16 miles north of Coleman, Alberta, on the easternmost slopes of the Rocky Mountains."

Jan 1, 1968

By W. J. Kuit

"Complex facilities which provide for the collection, management and treatment of effluents emanating from the Sullivan mine and concentrator tailings were made operational in October 1979. Key features of the system are the use of upgraded tailings ponds for the storage of up to 800 million litres of metals-contaminated effluents, a treatment plant employing lime in a high-density sludge process and a sludge-impoundment facility designed for maximum long-term environmental safety. The completed works are capable of satisfying a difficult range of operating requirements imposed by highly variable weather conditions, drainage flows and soluble metals loadings. Final capital expenditures for the project approached $10 million and annual operating costs are about $0.8 million.This paper discusses the Kimberley effluents treatment project and the major considerations in its development. The treatment process, major plant equipment and initial operating experience are also described.IntroductionCominco Ltd. has worked the Sullivan orebody at Kimberley, B.C. since 1909 and has operated a concentrator some 5 km distant from the mine since 1923. Over the last 70 years, in excess of 120million tonnes of ore have been mined, and production continues at an average rate of 6,500 tonnes per day. It is a well-known fact that the contribution of this operation to Canada&apos;s mining industry and, in particular, Cominco&apos;s development has been significant. However, this success has not been without some undesirable side effects.Unfortunately, the Sullivan is one of only a few major Western Canadian orebodies which may be classed as ""acidic"" in nature. That is, the primary economic minerals, galena and marrnatite, are enclosed in a siliceous host rock with abundant pyrrhotite, but with little or no accompanying alkaline gangue minerals such as calcite and dolomite. The unavoidable consequence of mining such an ore is that contact with air and water generates an acid mine drainage containing various soluble metals orginally present as minerals.This problem also arises in the concentrator&apos;s tailings ponds, which, in the case of the Sullivan, are two separate impoundments of different materials. The 1,100 tonnesl day of ""iron"" tailings are primarily pyrrhotite which is surplus to the requirements of a separate operation that produces sulphuric acid as an intermediate to phosphate fertilizers. Inert gangue minerals with only a minor sulphide content are the main constituents of the 1,200 tonnes/ day of siliceous tailings. Corresponding to the relative proportion of sulphides in the solids, the decant from the iron tailings is substantially more contaminated than that from the siliceous pond."

Jan 1, 1980

By Pierre Antoine Dhaiti, Gilbert Sergerie, Michel Dagbert, Jean-Maurice Brodeur

"Quality of iron ore is generally determined by several factors which can be correlated or independent. Among these f actors, we generally find per cent iron, silica, magnetite or hardness. Forecasting the short- and long-term fluctuations of these f actors in the future pit is an important feature of mine planning in these deposits. Computer simulation provides a realistic answer to these questions. It allows to generate values for the most important quality features of each shovel load with the proper correlations between them as well as between one load and the next being fully reproduced. Then different sampling schemes f or grade control or blending facilities can be examined on the simulated data. The mechanics of the simulation procedure and its potential applications are described in an example.IntroductionThe purpose of this paper is to illustrate the use of in-situ grade simulation in the planning o f the grade control in an iron ore min e. More precisely, given a production unit of given size, we need to know how many samples have to be collected in that unit so that we ca n recognize its grade with a reasonable precision. Conclusions that we would like to arrive at are of the type: with 4 blasthole samples we ca n get the iron grade of a 10,000 ton bloc k with less than a ± 2% Fe error 95% of the time.The approach t hat we take to solve this problem is simulation. We simulate the grade of samples and the grade of the block that contains these samples. We repeat the simulation for hundred s o f blocks. By comparing the sample grade with the block grade in each case, we determine the actual number o f blocks where the difference sample-bloc k is less than a given limit."

Jan 1, 1983

By R. Le Houillier, M. Nagamori, A. J. Plumpton

"Asbestos tailings are a typical serpentine, hydrated magnesium silicate, consisting primarily of antigorite and a few per cent of unrecovered fibrous chrysotile. Serpentine has unique thermal properties in that dehydroxylating calcination at 600 to 700°C can yield an amorphous structure in which most of the magnesia is liberated from the original bond with silica and thereby rendered chemically active. The amount of activated magnesia can be quantified by selective leaching with a weak acid such as acetic acid. Many wet processes have been proposed to extract magnesium values from calcined or natural serpentine by means of various acids and their ammonium salts. However, the only commercial utilization of serpentine today is found in dry processes such as the production of fused magnesium phosphate fertilizer .The present paper reviews the physical chemistry of the dehydroxylation of serpentine and also various wet and dry processes in order to provide a general view regarding the chemical transformation of asbestos tailings.IntroductionAsbestos fibers occur as chrysotile, a serpentine polymorph. More than nine tenths of mined asbestos ores consist of massive non-fibrous serpentine, primarily the polymorph antigorite, which is discarded as tailings after fiber extraction. For many decades, Quebec has been a world leader in the production of asbestos fibers. As a result, colossal tonnages of serpentine have accumulated in the Eastern Townships&apos;!&apos;. Serpentine minerals are found in large deposit s throughout the world, and significant research efforts have been made, particularly in Japan and the USSR, mostly in attempts to extract magnesia or silica values therefrom.The chemical composition of serpentine (chrysotile and antigorite) may be ideally expressed as Mg3Si2Os(OH). which corresponds to 43.7% MgO and 43.3% SiO2. Natural serpentines often contain a few per cent of Ni-bearing magnetite and other impurities, and therefore the contents of MgO and Si02are both about 40% or lower.Serpentine (hydrated magnesium silicate) is virtually insoluble in weak acids. However, when dehydroxylated under controlled conditions, &apos; it decomposes to an amorphous state in which magnesia and silica are isolated and chemically active. The magnesia so activated is readily soluble in weak acids. This unique characteristic of calcined serpentine, first discovered in 1942,, has since attracted the attention of innumerable researchers, whence many processes have been proposed."

Jan 1, 1980

By Yve Fourmanoit

"This paper discusses the exploitation of shallow underground deposits in a very altered geological environment. The methods, their adaptation to local conditions, their evolution, dilution control and recovery of mineral reserves will all be dealt with.The recovery of the B zone crown pillar under 40 m of till that was originally saturated with water, is of particular interest.Future underground development and production start-up of the A-2 zone, organization of mining operations, mechanical services, group incentives and safety practices will also be given.IntroductionThe underground deposit of B zone is not very deep. A 300 m shaft provides access to the mine. In addition , exploitation sublevels are developed every 20 m and are linked by a service ramp. The overburden located on top of the deposit is 40 m thick and is composed of a very dense till.A detailed work plan was initiated to permit mining under the overburden. To do so, it was imperative that efficient methods be developed. At a time when an accident at the Belmoral Mine shook the mining world , it was a task to convince provincial authorities that it was safe.While B zone was being mined , development began in the A-2 zone deposit which has recently been put into production (Figs. 1 and 2).The intention of this paper is to provide an outline of the mining method s and their particular aspects. To do so, some of the mine services are described and a brief outline of the under ground department is provided."

Jan 1, 1990

By E. Kouame, M. D. Everell, D. Hodouin, T. Kasongo

"To properly operate a mineral beneficiation plant it is often necessary to have systematic evaluations of the performances of a piece of machinery, of one of the processes or of the plant as a whole. The state of a process can be described from a collection of data: flow-rate values, particle-size distributions and chemical compositions of the various streams of the circuit studied.However, the obtained raw data are generally redundant and inconsistent from a material balance viewpoint, due to natural disturbances, sampling errors, unreliable instrument readouts and laboratory analysis inaccuracies.BILMAT is a computer program which upgrades mineral processing data, adjusting them in a least-squares sense in order that they may verify material conservation constraints. As a consequence, the program is able to calculate the best values of unmeasured flow rates (such as. circulating load ratios). BILMAT is a very general program in the sense that it can accept various data from any type of mineral processing circuit, and its usefulness is demonstrated here for three processing circuits of a pyrochlore concentration plant: grinding, desliming and flotation.IntroductionComputation of the material balance around any metallurgical process, that is the determination of stream flow rates and composition. is a basic step in its evaluation. In spite of the simplicity of the physical laws of mass conservation. and of the very fundamental need to know the flow of components around a process. it appears, particularly in mineral processing. that material balancing is quite often a difficult task. The reasons for this involve the problems associated with collecting measurements in mineral dressing plants. They are generally poorly instrumented and invariably data must be collected through hand sampling. Due to the heterogeneous nature of the streams, segregation occurs and samples are often not adequately representative, a problem made worse by the lack of circuit sampling facilities, which are often completely ignored by plant designers. Furthermore, the nature of the measurements to be performed (for instance particle size distributions in the fine range) frequently gives inaccurate results."

Jan 1, 1981

A series of small scale tests have been conducted to evaluate the effect of micro-fracture development, imposed by blasting, on the material properties of the rock as well as its resistance to crushing and grinding. The uniaxial compressive strength, tensile strength, Poisson?s ratio, P-wave, Swave velocity, point load test index, crushing and grinding work indices were evaluated for samples without any blasting load and for samples which had received a variety of blast loads ranging from a single impact with low strength detonating cord, to combination of impacts at different times and significant impacts with powder factors close to those used in practical blasts. It was shown that the rock mechanics parameters change even at low impacts, suggesting easier crushing of the rock. Damage values appear to be affected by timing as stress wave superposition affects the damage process. Fragmentation is achieved at higher impact levels while work index modification of the fragments is also observed when high powder factors are used, suggesting improvements in grinding.

May 1, 2003

By A. D. Hunter, J. M. JR. Moore

"The Aldermac deposit and associated prospects occur in the Noranda Archean volcanic centre of the Abitibi greenstone belt. Over two million tons of are grading 1.65% copper, with minor gold and silver, were mined between 1933 and 1943. The deposit has features in common with the Vauze and Millenbach mines in the same district.Recent detailed mapping, geochemistry and petrography combined with data from former diamond drilling and mining operations permit a re-interpretation of the Aldermac area. The orebodies and spatially related sulphidic zones are con eluded to be volcanogenic.The host rocks are a chemically bimodal suite of mafic and rhyolitic flows, volcaniclastics and related subvolcanic intrusions. Massive sulphide lenses are spatially related to a quartz-feldspar- phyric rhyolite dome and siliceous, volcanic-exhalative sedimentary rocks, The succession is cut by gabbro and syenite, related to later stages of volcanism, and by post Kenoran diabase dykes. Regional metamorphism attained the low greenschist facies, but the rocks lack penetrative deformation.Hydrothermal alteration is primarily an intense silicification of mafic volcanic rock s enveloping, or lying below, sulphidic zones. Chlorite and sericite alteration zones, including dalmatianite, are more locally developed and have a closer spatial relation to mineralization, as do epidote, calcite and calcic garnet.The structure is complex and cannot be explained by isoclinals folding; rather it reflects concurrent faulting, and extrusive and intrusive activity. Fault blocks were rotated and exhibit opposed facing; the original selling was possibly a submarine graben.Sulphidic zones occur within mafic and felsic volcanic rocks and at the interface between the two; there is thus potential for discovery throughout the known stratigraphic succession. Exploration conducted according to a volcanogenic model is advisable, particularly in the light of recent discoveries in similar rocks of the Amulet area."

Jan 1, 1983

By Ali Bunjaku, Lauri Pesonen, Hannu Johto

It is well known that there are many ways to process copper concentrates into copper anodes using the pyrometallurgical route. All modern copper smelting technologies are fundamentally energy efficient and environmentally safe options, and therefore choosing one depends on the desired capacity range, feed impurity levels, plant location, flexibility needs, overall energy use, and of course smelter economics in both the short and long term. This paper focuses on comparing different solutions which have potentially the lowest variable opex (operational expense), meaning in practice finding out which technology offers the best chances for profit maximization under certain scenarios. For the comparison, we chose to have a closer look at Outotec Flash Smelting (FSF) – Peirce-Smith Converting (PSC), Outotec Flash Smelting (FSF) – Outotec- Kennecott Flash Converting (FCF), Outotec Ausmelt TSL Smelting (ASF) - Peirce-Smith Converting (PSC), Outotec Ausmelt TSL Smelting (ASF) - Outotec Ausmelt TSL Converting (ACF), Mitsubishi Smelting Process (MIT), Bottom Blowing Reactor (BBR) – Bottom Blowing Continuous Converting (BCC), and Side Blowing Furnace (SBF) - Top Blowing Converting (TBC) since these seem to be the main state-of-art technologies now being applied in many recent copper smelter projects around the world. The work was carried out by modelling each smelting route by using the new HSC SIM 9 simulation software and applying operation time, energy, and consumables consumption numbers for each unit process and stream. Combined with cost data, the exercise produced a rich set of information which will be shown in detail for each area per scenario. The authors’ goal here was to provide a fair comparison where each technology can be evaluated from various perspectives such as electricity use or refractory consumption. INTRODUCTION Copper can be produced either pyrometallurgically or hydrometallurgically. The hydrometallurgical route is used only for a limited amount of the world’s copper production (~20%) and is normally only considered in connection with in-situ leaching of copper ores. On the other hand, most of the copper extraction from Cu-Fe-S minerals is pyrometallurgical (~80%) (Schlesinger 2011, ICSG 2017). Thus, several different processes can be applied for copper production, including the following state-of-the-art technologies: Outotec Flash Smelting (FSF) – Outotec-Kennecott Flash Converting (FCF) Outotec Flash Smelting (FSF) – Peirce-Smith Converting (PSC) Outotec Ausmelt TSL Smelting (ASF) - Peirce-Smith Converting (PSC) Outotec Ausmelt TSL Smelting (ASF) - Outotec Ausmelt TSL Converting (ACF) Mitsubishi Smelting Process (MIT) Bottom Blowing Reactor (BBR) – Bottom Blowing Continuous Converting (BCC) Side Blowing Furnace (SBF) - Top Blowing Converting (TBC)

Jan 1, 2019

By Takao Oishi, Go Ohara, Toru Kitazaki, Masahiro Tanaka

"The High Pressure Acid Leach (HPAL) plant for nickel-cobalt mixed sulphide production at Coral Bay Nickel Corporation (CBNC) in the Philippines has been in operation since 2005 with a capacity of 10,000 t/year of nickel. Subsequent to the commissioning of the second plant in 2008, the production capacity increased to 22,000 t/year of nickel (Llerin et al., 2011). CBNC’s annual nickel production reached more than 24,000 tons of nickel in 2014. The concepts to achieve this capacity are the high availability and the reciprocally flexible operation of both plants. The availability depends on some factors, such as the control of impurities in the process and the equipment condition, to mention a few. In the HPAL process, it is not only the autoclave operating conditions that affect nickel extraction but also the impurities in the ore greatly influence it. The major element in the ore is iron and most of this iron is precipitated as Fe2O3, while the rest remains as Fe2+ or Fe3+ sulphate in solution. These ions in solution reduce the availability, so it is important to control the formation of iron ions by controlling the impurities in feed ore as well as the HPAL conditions. This paper presents the general HPAL process and the behaviour of impurities, focusing on iron behaviour in the HPAL process.INTRODUCTIONCoral Bay Nickel Corporation ProfileCoral Bay Nickel Corporation (CBNC) was founded on April 2002, as a joint venture of four companies; namely, Mitsui Corporation (18%), Sojitz Corporation (18%), Nickel Asia Corporation (10%) and Sumitomo Metal Mining Corporation (SMM) with a controlling stake of 54%. Aside from its capital share, Nickel Asia Corporation also supplies the ore and limestone for the High Pressure Acid Leach (HPAL) plant located in Rio Tuba, Philippines, as shown in Figure 1 (Tsuchida, 2008). The objective of the CBNC project is to produce 22,000 t/year (original design) of nickel and 1,500 t/year of cobalt, as sulphide, by the treatment of nickel laterite ore which is a low grade nickel oxide ore in the Philippines (Mines and Geosciences Bureau, 2014). The sulphide product has been exported as a raw material to the SMM Nickel Refinery in Japan for 30 years. The product of this plant, a mixed (Ni/Co) sulphide, is shipped to the SMM’s Nickel Refinery in Niihama, Japan. SMM Corporation provides the technology and management personnel to the plant. SMM Corporation also supplies the sulphuric acid, which is the main reagent for the HPAL process."

Jan 1, 2016

Train on Different Equipment - * Immersive?s interchangeable cabin controls technology - ?clip on & off? * Change Simulator from one machine to another in minutes * No technical expertise required to swap * Real, functioning, controls and displays are used to aid rapid learning Immersive has produced a range of Conversion Kits to suit most equipment. Modular design - Easy to convert from one machine model to another with a Conversion Kit. Caterpillar Models Trucks - 769D, 773D, 777D Trucks - 785B, 789B, 793B Trucks - 785C, 789C, 793C, 797 Excavator/Shovel - 5130, 5230 Front end loader ? 992, 994 Dozer ? D10, D11 Komatsu Models Trucks - HD325, 785-5, 985-5 Trucks - 730E, 830E, 930E Dozers - D375A-3, D475A-3 Shovel - PC8000 P&H Shovels - 4100A, 4100XPB, 4100BOSS Hitachi Shovels - EX2500, EX5500 O&K Shovel - RH200 Bell Articulated Truck - B40C

May 1, 2003

By O. Neves, C. G. González Beca, M. C. Sol Pereira, H. Sousa Vale, R. A. Guedes de Carvalho, M. N. Sampaio

"As sulphide ores are usually concentrated by flotation , the material is very finely ground <37um), wet and impregnated with the chemicals used in flotation. These conditions are favourable to the development ofchemical reactions which are largely influenced by atmospheric conditions (temperature, humidity, wind, etc.) as well as by the geometry of the piles.Physical and chemical properties of a chalcopyrite concentrate were determined by laboratory tests. The knowledge of these properties was considered necessary in order to establish a correct design of the storage and handling operations of the sulphide ore concentrates obtained by flotation.The properties studied in this work were: transportable moisture limit, flowability, effects of vibration, hygroscopicity, ""caking"", chemical alterations by humidity, oxidation and self-heating (auto-ignition, dry and wet oxidation, self-heating by humidification and its prevention).INTRODUCTIONIn order that the handling and the transport of a powdered material may be carried out correctly, it is necessary to know certain physico-chemical characteristics. Transportable moisture limit (TML), apparent density (both aerated and compacted), compressibility, angle of repose, angle of spatula, cohesion and angle of slide(l-4) are characteristics (among the flowability parameters) worth knowing.Moisture content of the powdered material is fundamental, because if this is too low heavy losses will occur when the product&apos;s particle size is very small, if it is too high, separations between solid and liquid phases may occur. In the latter case, the centre of gravity of the system may change suddenly and cause accidents, mainly if transport is by sea or by river."

Jan 1, 1989

By I. H. Warren, F. A. Forward, A. Vizsolyi

"Observations are reported on the pressure leaching of material produced by subjecting chalcopyrite to two types of heat treatment. Calcination of the mineral at 825°C, in the absence of oxygen, induces some sulphur loss by volatization, producing a material from which copper can be leached more rapidly than from chalcopyrite. Treatment of the mineral with elemental sulphur at 475°C leads to sulphur uptake accompanied by a change in mineralogical structure of the chalcopyrite. Copper is prefer-entially and rapidly leached from the sulphur-treated material. A tentative explanation of the sulphur-chalcopyrite re-action is presented."

Jan 1, 1968

By J. Suarez

The innovation initiatives for world-class mines today and in the future focus on automation and robotics in equipment and machinery. These innovations have benefited from the development of advanced tools in global positioning, the Internet, the capabilities of data storage, transmission and handling, and intelligent systems. Forward-thinking companies have been investing in automated trains and trucks, selfdrilling rigs, intelligent flotation systems, etc. Considering that the emphasis has been mostly laid on improving the performance and reliability of the equipment and machinery, it is not surprising that the visibility was geared toward mechanical, electrical, process, and metallurgical engineering. One of the critical disciplines, mining engineering, has had less shine from the spotlight of automation and robotics. Mining engineering is concerned with the design, the operation, the management, and the reclamation of mines and mining facilities. In essence, it does benefit from the advantages of automation and robotics in equipment and machinery. However, being ?left out? in the innovation process may impede the core capabilities of this engineering discipline, which would create a two-tier knowledge and technology system in mines. For example, shovels in an open pit may be equipped with technology that can send real-time data of actual payload, number of buckets, mechanical status, etc. But, are mining engineers aware of the possibility to incorporate the data into their planning tools in order to have updated forecasts and accurate information? And if they are, are they equipped with the tools to reap the rewards of those technologies? And if so, is the personnel trained to use the tools efficiently? This paper is a contribution to the discussion on the technological advances in mining engineering. For the authors, the roadmap to the future requires a smart integration of technological advances in hardware and software so that mining engineers are not only aware of the possibilities, but also trained and capable of using the available tools. Essentially, this paper believes that automation and robotics in equipment alone will be undervalued and underutilized if the owners and drivers of the mining systems (i.e. the mining engineers) do not possess the tools and training to integrate the technological advances into the functions of mining engineering. The intent of the paper is to analyze the available technologies for the core mining engineering functions of design, planning, scheduling and optimization. The analysis will lead to discussions and suggested solutions on integrative technology solutions that would create optimum value for the mining processes and equipment technologies.

Aug 1, 2013

By D. Lauzon, H. de Ruiter

"In 1988a decision was taken to design and install a computerized mine monitoring and control system. This system had to monitor and control all pumping and ventilation underground. The operation of the mine air heating, using waste heat from the mine water and compressors, was to be part of the system. It ultimately also had to interface with the four existing Canadian General Electric Series 3 PLC&apos;s which controlled the No .3 shaft loading pockets. Beside operational control and trouble shooting, the system is a valuable tool in energy management and ultimate savings are estimated at $50,000 per year.The final equipment selection was a General Electric Series Six PLC on surface with a total of 17 Series One Plus and Juniors PLC located underground. Data is transferred through a two-pair shielded cable using modems. Both analog and digital functions are being utilized.The basic monitoring and control system was commissioned during 1989and, due to a higher level of technology today, further improvements have been planned for the future. The system was designed by Walter Dow together with Gordon Champion of D.G. Champion Engineering Ltd. of Toronto. Advice for the ventilation part of the project was obtained from Maurice White, Independent Ventilation Consultant.The Ministry of Energy, Mines and Resources and the Ministry of Energy of Ontario approved this project together with the waste heat recovery project to qualify for a grant of$135,000 under the Enerdemo-Canada program.IntroductionThe Macassa mine is a narrow vein gold mine situated about 2 km west of the town of Kirkland Lake in northeast Ontario. The mine has been in continuous operation since 1933 and a total of about 3.0 million ounces have been recovered out of 6.6 million tons of ore ."

Jan 1, 1991

By Derek E. McBride

"Exploration work in the Beardmore - Tashota area has led to a reinterpretation of relationships between gold mineralization and the geologicalevolution ofthe area. The host volcanic rocks form two parallel volcanic belts connected by a much smaller cross-cutting band, which trends northeast from Beardmore to Tashota. This connecting band consists of mafic and felsic volcanic, plus clastic sedimentary rocks in a sequence conformable with the contact of the Onaman Lake Batholith to the east. A metamorphic aureole or incorporated xenoliths are lacking along this major contact and the only intrusive relationship observed is chilling between mafic dikes and a cold host granite in proximity to it. Granite dikes are totally lacking in the volcanic succession, or the overlying sedimentary sequence. A major part of this sequence consists of a polymict basal conglomerate with granite boulders and volcanic clasts in a fine-grained chloritic matrix. The nearest source for these boulders is the Onaman Lake batholith.Gold mineralization in significant economic quantities (+ 50 000 ounces) occurs at the top or above the mafic volcanic succession as quartz bands. In the Northern Empire Mine, the band is conformable, folded, boudinaged and the mineral zoning shows a relationship to variations in the host rock, not structural overprinting. In general, where the host mafic tuff is medium-grained, the quartz band is thicker, up to a metre wide, and carries economic grade; where the tuff is finer-grained and bedded, the band is very thin and low grade.Stratigraphic control and metal zoning shows that the mineralization formed as part of the development of the volcano- sedimentary succession. The other major deposits in the area (Leitch and Sturgeon River) have a similar structural history suggesting that they are also syngenetic in terms of the stratigraphic development. Regionally, these deposits were emplaced prior to any significant tectonic deformation but at the end of the mafic volcanic event.The mafic activity was related 10 a period ofextension which caused the volcanic troughs to develop along centres of rifting. The hiatus at the end of this event permitted extensive hydrothermal systems to form and deposit siliceous exhalite bands within sedimentary or terminal mafic volcanic environments in promixity to major thermal sources. Subsequently, the Kenoran Orogeny deformed the entire succession into upright folds with a sub-vertical schistosity. Evidence shows that the deposits have remained intact since deposition."

Jan 1, 1987