Search Documents

By J. W. M. Porritt, K. C. Cheng

Knowledge of radon emanation rates from uranium-bearing rocks is essential to the design of mine ventilation systems for uranium mines. Measurements of equilibrium ratio between radon and its daughters in mine air are important for a better control of mine radiation conditions. The concentrations of radon and daughters were monitored at cut-and-fill stopes in the Beaverlodge Mine of Eldorado Nuclear Ltd. during all phases of the mining cycle. The radon emanation rates of ore and rock samples were measured at the laboratory and the results were compared with in-situ emanation tests in an isolated ore drift. Samples of backfill solution, backfill drainage and ground seepage water were measured [or radon and analyzed for radium and uranium. The results showed that discharges of backfill solution and daily shift-end blasts were the two major sources for a rapid release of radon gas in the ventilation air. Other mining operations, such as drilling, mucking, etc., contributed little effect on radon release to the mining environment. Radon emanation rates of the Beaverlodge are samples ranged from 13 x 10-18 to 600 X 10-18 Ci/cm2/ sec and that of waste rock samples from 0.54 x 10-18 to 13.4 X 10-18 Ci/cm2/sec. The in-situ emanation rate of mine walls with ore-to-rock ratios of 1 to 7 was 60 x 10-18 Ci/cm2/sec. The average equilibrium ratio of radon and its daughters in stapes was 32.6%. Under a normal ventilation condition, the average background levels of radon concentration in cut-and-fill stopes ranged from 13 to 80 pCi/L. The discharges of backfill solution during backfill operations at 100 tons solids per hour released approximately 1.8 x 106 pCi/min of radon and elevated radon concentration in stapes 2 to 5 times above the background levels.

Jan 1, 1981

By David R. Ray, Arthur J. Pyron, William F. Thomann

"Proterozoic plutonic and volcanic rocks in the Franklin Mountains, west Texas, exhibit similar values in average concentrations of equivalent uranium (eU), equivalent thorium (eTh) and equivalent potassium (eK) when compared to Proterozoic igneous rocks of the southwestern United States. Variations of radioelement concentrations for all Proterozoic igneous rocks of the Franklin Mountains range from 1.1 to 357.1 ppm U, 2.1to 259.1 ppm Th and 2.5 to 10.2% K.Recent geologic mapping of the Proterozoic rocks in the Franklin Mountains revealed several types of granites previously unrecognized, and these warrant further exploration for U and Th resources. Fluorite-bearing granites and riebeckite pegmatites are likely targets for further investigation, as these have the highest U and Th concentrations compared to all other granites.IntroductionThis is a summary of the paper presented at the CIM Geology Division Uranium Symposium held in Saskatoon, Saskatchewan, September 8-13, 1981. The purpose of this study was to evaluate the distribution of uranium (U), thorium (Th) and potassium (K) in Proterozoic igneous rocks in the Franklin Mountains, and compare radioelement concentrations to Proterozoic igneous rocks elsewhere in the southwestern United States.General GeologyThe Franklin Mountains are located in west Texas and southcentral New Mexico, within the southeastern part of the Basin and Range Province o f the southwestern United States. The Franklins are a complex fault-block range trending northsouth with strata dipping toward the west. Ages of the rocks range from Proterozoic to Cretaceous. Harbour (1972, 1960) provides the most recent account of the general geology of the Franklin Mountains. Most recent accounts of the detailed Pro Proterozoic geology o f the Franklins are provided by Hoffer (1976), Thomann (1980, 1981), Pyron (1980), Ray (1982) and McCutcheon (1982)."

Jan 1, 1983

By Eric Pirard

"A mineralogical and trace element analysis was performed on the Küre historical slags in order to evaluate the possible recovery of copper and cobalt. Reflected light microscopy, electron microprobe and image analysis were combined to determine the Cu and Co distribution in the slag.The results indicate that 81% of the total cobalt is chemically combined in the fayalite whereas only 3.4% is in the mechanically entrapped sulphides. The remainder being in hercynite and wiistite. On the other hand, 95% of the total copper is in the sulphide phase.This kind of applied mineralogical investigation gives invaluable information when it is performed preliminary to metallurgical experiments.IntroductionThe recycling of metallurgical slags is a growing business. The operation is directed toward recovering base metals (Cu, Pb, Zn), and by-products (Floyd and Mackey, 1981).Two reasons are invoked to explain metallic losses in slags: (1) mechanical entrapment of matte globules in the silicate melt; and (2) chemically combined metals in the slag-forming phases. Obviously, a chemical analysis of the slag cannot distinguish between those two modes. Grinding and flotation of the liberated sulphides have often been used to evaluate the importance of mechanical entrapment (Mechev, 1970; Imris , 1982).Recent studies in applied mineralogy of pyrometallurgical products (Bérubé et al., 1987; Pignolet et al., 1986) have demonstrated the benefits of quantitative mineralogical analyses of slags. Optical microscopy together with electron microprobe and image analysis offers a powerful and easy way of quantifying the relative importance of mechanical and chemical losses."

Jan 1, 1991

The fracture behavior of second phase particles and the role of matrix material on the wear resistances of the three Al-Si alloys containing 8, 17, and 19% Si were investigated using single pass scratch testing technique by applying normal loads between 0,15 and 5,00 N, in ambient air, Optical microscopy and SEM with EDS were used to analyze microstructures and morphologies of scratch tracks of the Al-Si alloys, The results showed that needle-like Si particles fractured under a load of 0.50 N, while block-like Si particles fractured at loads above 3,00 N, The Al-17% Si alloy with large number of needle-like particles (area fraction 16,4%) exhibited the highest coefficient of friction (0,8) and the widest scratch track, The Al-19%Si alloy containing high Si percentage and larger number of block-like particles (area fraction 16%) exhibited the lowest coefficient of friction (0,37) and the narrowest scratch track width. Presence of block-like particles was effective in reducing the amount of material transfer from Al-Si alloy surfaces to the counterface.

Jan 1, 2005

By Michel Gauthier, Jacque Trottier

"ForewordA symposium on base metal deposits was held in Bathurst, New Brunswick, from June 10-13, 1990, sponsored jointly by the Geological Surveys Branch of the New Brunswick Department of Natural Resources and Energy, the New Brunswick Prospectors and Developers Association, and the Geology Division of the Canadian Institute of Mining, Metallurgy and Petroleum. Papers prepared for the symposuim are being published as a series of articles in the CIM Bulletin. This third paper (the first was by Fyffe, et al., in Vol. 83, No. 938, the second is in this issue) in the series presents an overview of the tectonic setting and geochemistry of base metal deposits in the Eastern Townships of Quebec.ABSTRACTIt is well known that the classification system of volcanogenic massive sulphides (VMS) is based upon their metal content. This metal content, the result of hydrothermal solutions circulating within strata underlying the deposits, is generally thought to be related directly to two parameters: (1) the nature of the underlying stratigraphic sequence; and (2) the physico-chemical conditions that existed at the time of the hydrothermal event. Furthermore, these two parameters are, in turn, related to the tectonic setting. One must bear in mind that these parameters are diachronous and evolve with time. These factors are considered in our analysis of the major VMS deposits of the southeastern Quebec Appalachians. This analysis will describe the time and environment of formation of these deposits and integrate them into an evolving paleotectonic model.VMS deposits in the southeastern Quebec Appalachians formed during three distinct metallogenic episodes. During the first episode, which involved early closing of the Iapetus Ocean and associated destruction of oceanic crust by subduction processes(Early Ordovician?), cupriferous VMS deposits hosted by pillowed, mafic (boninitic) lava flows were formed in immature island-arc systems (""Cyprus-type"", e.g. Huntingdon deposit).In the second episode, which also occurred during the closure of Iapetus but at a later stage (Early to Middle Ordovician), mature island-arcs formed and hosted polymetallic VMS deposits (""Kuroko-type"", e.g. Eustis deposit).Finally, during culmination of the Taconic and/or Acadian orogenies (Middle Ordovician and/or Devonian), transtensional basins, associated with tholeitic to transitional mafic volcanism began to develop. Major sedimentation occurred contemporaneous with volcanism, and within this framework polymetallic VMS deposits were formed (""Besshi-type"", e.g. the Memphremagog deposit).Although incomplete, the proposed paleotectonic model represents the sequence of the tectonic settings that prevailed during the formation of the VMS deposits of the southeastern Quebec Appalachians."

Jan 1, 1991

By Ferri P. Hassani, Riadh Bouzaïene

"Selected methods of pressure loss predictions in horizontal slurry flow in pipelines are presented. For a given combination of flow velocity, solids concentration and particle size, the slurry and its flow conditions are described, and an appropriate method of pressure loss prediction is outlined. The wide range of conditions treated in this paper may be found in practice in areas varying from the hydraulic transport of low concentration slurries to dense-phase conveying of paste backfill in underground mines.IntroductionThe hydraulic conveying of solid particles in pipelines is a major component of the mining and mineral processing industry. Whether the objective is to transport ore to the processing plant or to make use of mill tailing as backfill material; the need for well designed, economical hydraulic conveying systems is recognized.The contribution of this paper is part of an on-going research program at McGill University involved in optimizing and developing techniques for total mine waste disposal. One of the main concerns in the conveying of solid-liquid mixtures is the prior knowledge of the pumping power input required. This energy requirement is directly proportional to the pressure losses incurred in the pipeline system. Understanding the sources of such pressure losses and predicting their magnitudes should enable the system designer to make informed decisions regarding the optimum mode of hydraulic transportation commensurate with the over-all requirements of the operation.This paper is an attempt to classify pressure loss prediction methods encountered in the literature for solid-liquid mixtures. In spite of the large number of publications spanning thirty years of research in the field of slurry transportation, it is sometimes difficult to correctly identify the appropriate methods applicable to a given situation. This is partly due to the inherent complexity of the mechanics of slurry flow and the ensuing uncertainty about the nature of the flow regime under investigation.Our approach is to use three fundamental parameters, namely: flow velocity, solids concentration and particle size (for solid particles with a given density) to characterize the slurry and the flow conditions, and to match them with an adequate pressure loss prediction method. For each combination of flow velocity, solids concentration and particle size, a description of the most likely prevalent flow conditions and some known methods of dealing with them will be presented. Qualitative definitions of ""high"" and ""low"" magnitudes of the aforementioned parameters will be given as a general guide to the classification scheme presented in this paper."

Jan 1, 1992

By Y. Wang

Phosphates and fluorides are used as regulators for the removal of silicates from diasporic-bauxite both in direct and reverse flotation. While using dodecylamine chloride as a collector, micro-flotation studies showed that sodium hexametaphosphate has stronger depressing power on diaspore than on silicate minerals with increasing sodium hexametaphosphate concentration at pH 6.5, but sodium fluorosilicate shows poor depression on diaspore with increasing sodium fluorosilicate concentration at the same pH. Zeta potentials of diaspore and silicate minerals become more negative both in the presence of sodium hexametaphosphate and sodium fluorosilicate. Adsorption density studies indicated that the adsorption density of sodium hexametaphosphate on diaspore is much higher than that on silicate minerals at the concentration of 75 mg/L. FTIR spectroscopy studies show that sodium hexametaphosphate interacted with the Al atoms exposed on the diaspore and silicate minerals surfaces to form P?O?Al bonds through the P02 groups. It is possible that sodium fluorosilicate interacted through F- or [SiF6]2- with silicate minerals surfaces based on the analysis by AES.

Jan 1, 2006

By C. A. Petch

Abstract - The High Lake polymetallic deposit is located in the northern Slave province, 40 km south of Coronation Gulf, Nunavut. The main zone, the AB zone, hosts an estimated resource of 3.56 Mt grading 5.0% copper, 1.1% zinc, 0.06% lead, 1.7 g/t gold, and 18.2 g/t silver. Archean felsic metavolcanic and metavolcaniclastic rocks are the dominant rock type and are associated with lesser mafic metavolcanic and carbonate-rich metasedimentary rocks. The sequence strikes north-northeast, dips steeply to the west, and is truncated to the west by a large granodioritic intrusion. The mineralization at the AB zone is comprised of massive and stringer chalcopyrite-sphalerite-pyrrhotitepyrite± galena. At the core of the mineralized zone, intensely chlorite-altered rocks are locally metamorphosed to form distinctive zones of anthophyllite-magnetite-cordierite-altered rock. Peripheral to the mineralized core, alteration consists of sericitization, silicification, and weaker chloritization. Primary morphology and facing direction of the zone are difficult to interpret in part due to poor primary metal zonation of the deposit. However, the irregular shape of the mineralized zone and the erratic zones of zinc enrichment at the fringes are consistent with the interpretation that the zone was formed by the replacement of a porous volcaniclastic pile.

Jan 1, 2004

"This paper discusses the use of risk assessment and risk management techniques within the Australian underground coal mining industry, within the context of geotechnical risk. The industry works within a pro-active, “enabling” legislative framework, where companies and management apply a range of risk assessment tools as part of their everyday management processes. Different geotechnical risk factors and approaches are reviewed, together with application examples – ranging from mine planning and design, operations, and accident investigations.A particularly powerful resource in each of the above stages of geotechnical management is the RISKGATE system. RISKGATE is an assembled “body of knowledge” structured under different topics across the Australian coal industry, of which three topic areas address rock mechanics issues for both the underground and surface mining sector. This paper will provide an overview of RISKGATE in the context of risk-based rock mechanics applications in underground coal mining."

Jan 1, 2015

By R. P. van Hille, A. W. van Zyl

The BIOX® culture, aiding liberation of arsenopyrite/pyrite occluded gold, is inhibited by thiocyanate (SCN > 1 mg/L); precluding the recycling of tailings water up-stream of the bioleaching circuit. The activated sludge tailings effluent remediation (ASTERTM) process is a biological process that was developed to facilitate water recovery and treat waste water on-site (to achieve a SCN concentration < 1 mg/L) to be recycled or disposed of. The aim of this study was to investigate the effects of changing temperature and SCN loading on the SCN degradation ability of the mixed microbial population clue to seasonal temperature changes and fluctuations of SCN concentration in the waste water.

Jan 1, 2011

By Mike Anderson

The annual budget for the repair and maintenance of equipment at Syncrude Canada Ltd is in excess of 450 million dollars. Of this amount, a significant portion can be attributed to the loss of material on various pieces of equipment throughout the operation. In order to effectively battle the different wear and corrosion mechanisms that lead to material loss, it is important to understand how materials behave in the environments in which they are used. Through the work carried out at Syncrude, and work conducted with various external collaborators, significant improvements in both equipment reliability and productivity have been achieved. This paper will review some recent field trails where materials research has demonstrated the potential for significant improvements in equipment run life and reduced maintenance costs. These field trails will demonstrate the need for understanding the interaction between various damage mechanisms and the materials used in different services. The paper will also discuss current areas of focus along with future directions for further work.

May 1, 2003

By H. Weissenbaeck, B. Nowak, M. Oesterreicher, R. Stastny

The producers of certain metals like nickel and cobalt increasingly face a shortage of easy-to-mine and easy-to-process ore bodies. Their focus is shifting towards alternative raw materials which in turn demand new, different extraction techniques. One potential route for processing a ferrous ore with a non-ferrous target metal is atmospheric leaching with hydrochloric acid followed by purification of the pregnant leach solution (PLS). For the separation of iron from the PLS, and, in turn, the extraction of the non-ferrous compounds, the following flow sheet is proposed. Pre-concentration of the PLS, oxidation of ferrous (if present) to ferric chloride, hydrolysis of ferric chloride leading to the precipitation of hematite and the evaporation of hydrochloric acid, followed by crystallization of non-hydrolysable metal chlorides by means of sparging hydrogen chloride into the solution. Hydrogen chloride required in the latter step is produced internally by super-azeotropic distillation of regenerated hydrochloric acid. The liquid filtrate from the crystallization step is recycled to hydrolysis. Depending on the specific composition of the PLS, the hematite produced contains only traces of other impurities, whereas the crystallized mix of non-hydrolysable metal chlorides – containing also the target metal in enriched form – contains ferric chloride only in an amount referring to the filter cake moisture. These crystals can then undergo further hydrometallurgical separation and extraction processes. As an example, this flow sheet is proposed for treating nickel laterite ores. Experiments related to the demonstration of crucial assumptions in the flow sheet are presented. Based on those experiments a mass and energy balance of the flow sheet was calculated and is presented here together with a table of the major consumables in order to provide a basis for an operating cost estimate and other process economics.

Jan 1, 2016

By Jan Rosenkranz, Anders Sand, Lisa Malm, Nils-Johan Bolin

Within flotation technology the general trend is towards very large cells. Scale-up is usually done by postulating geometrical similarity, which implies keeping the aspect ratio constant when increasing cell volume. Consequently, the design of flotation circuits typically involves several cells of identical geometry within a bank. Using a few standard sizes in a flotation plant simplifies design, manufacturing and maintenance of the cells, but does not necessarily guarantee optimal performance and selectivity of the flotation process. Geometry parameters for a given cell volume that influence flotation cell performance include cell height, which causes changes in the hydrostatic pressure and suspension hydrodynamics, and also influences the travel distance of particle-bubble agglomerates as well as the homogeneity of the mixing. Also the thickness of the froth layer depends on the aspect ratio of the cell. The objective of this work is to gain a better understanding of material distribution and properties within a flotation cell and, based on this information, elucidate how alterations of the cell geometry can influence separation efficiency. For this purpose systematic measurements and analyses of the spatial distribution of the different phases within a 160 m3 flotation cell have been carried out with a particular focus on an industrial, low-grade copper ore beneficiation process. The concepts for sampling at different vertical and lateral positions of the flotation cell are introduced. The results from the experimental work give an understanding of internal material distribution within flotation cells. Based on the measured phase distribution and concentrations as well as particle properties at various positions within the cell, the implications for an optimized scaling and design of individual flotation cells within a flotation circuit are discussed.

Jan 1, 2016

By Sabine Noelte, Mikko Petteri Rantamäki, Christopher Robben, Anssi Takala, Karl-Erik Rånman

"Sensor-based ore sorting is on its way to establish as a standard option for physical separation. The increasing number of installations in coal, iron ore, industrial minerals and hard-rock metal mining segments underlines the technological and financial potential that is beginning to be untapped. The Ma’aden Phosphate installation with 1.650 t/h sensor-based ore sorter feed sets a new benchmark for the possible capacity of stationary installations. Besides stationary installations, including multiple sorters parallel in different size ranges and multiple stages, containerised semi-mobile plants are applied. These offer two advantages, first being the reduction of transport costs when applied close to the mining face. The second is that semi-mobile systems enable processing of tens of thousands of tonnes of ore in a piloting phase with an approximate duration of 0.5 to six months, verifying the results laboratory mini-bulk tests on 5–10 tonnes of sample. This is especially important for low-grade metal ores because of the inherent Fundamental Sampling Error, as well as the Grouping and Segregation Error. The paper elaborates the results achieved within the I2MINE project, treating polymetallic ore at the Boliden Concentrator in Sweden.INTRODUCTIONSensor-based ore sorting (SBS) is becoming a standard option for physical separation, applied in all segments of mineral production. The Umm Wu’al project sets the bar for stationary SBS installations with 1,650 t/h feed (TOMRA, 2015). TOMRA Sorting Solutions has finalised an agreement in cooperation with Outotec to supply Outotec-branded sorting solutions for the mining and metallurgical industry (TOMRA, 2014). Especially for low-grade hard rock metal ores, an interdisciplinary approach is necessary applying experts for all aspects of mineral production. Due to the impact on the whole process stream, it is important on the end user side to have high level managerial support and involve all disciplines to ensure that all stake holders are involved in the analysis."

Jan 1, 2016

By A. E. M. Warner, A. Vahed, P. J. Mackey

In the decade 2002 to 2012 some 6.7 million tonnes of new copper concentrate production capacity was brought on line, corresponding to 2 million tonnes of contained copper. This increase in concentrate supply necessitated the commissioning of a number of new copper smelters as well as the modernization and/or expansion of existing plants to meet the demand. This paper gives an overview of the copper extractive industry, reviews recent copper production trends and changes in the copper industry, including an examination of pyrometallurgical and hydrometallurgical technology developments. WorleyParsons has supported a number of the projects involved in these developments and this role is briefly discussed. The paper introduces a number of ideas related to possible future directions of the copper industry.

Jan 1, 2014

By J. Drelich

We report structural forces measured for 10 nm silica particles deposited on alumina substrate and 5-80 nm alumina particles on mica using atomic force microscopy technique. For nanoparticles forming clusters, oscillation of structural forces was recorded with a periodicity that is close to the size of the nanoparticles used. Additionally, selected force-separation results indicate that the forces involved between the AFM probe and individual nanoparticles can be studied using the nanoparticle-coated substrates.

Jan 1, 2006

By Mitchell Gordon

"In almost all thickener applications the highest possible solid/liquid separation efficiency is what is desired by the user. There is a trend in the industry due to monetary restraints and environmental pressures to look at ways to extract this maximum performance by either retrofitting existing thickeners or installing the most cost effective new thickener. This paper looks at some of the common problem areas and presents a range of solutions developed by Outokumpu Mintec in North America and outokumpu's subsidiary Supaflo Technologies Pty. Ltd.The Emerging PictureAfter many hours of discussions with a large number of plant personnel over the last two years a picture began to emerge regarding current thickening operations in the industry. Initially, it seemed that everybody had their own unique process problems and therefore needed a correspondingly unique solution. Looking more closely at all the cases and the ideas that we had either implemented or suggested, it gradually became apparent that the majority of operators all had one and the same process need ....""Better Separation Efficiency""The range of operational problems that were uncovered in the survey were much more varied than expected and often were not even considered initially to be thickener problems. Often, it was only after the rejection of many solutions to the problem, generally due to capital cost, that the actual cause of the problem was looked at and found to be a thick-ener.A summary of the problems that have so far been identified is presented in Table 1. They are subdivided under three major categories of environmental, process and paste fill to highlight the wide range of mining activities that can be affected by poor thickener performance. These seem to be the major areas where the need for better separation efficiency is rooted."

Jan 1, 1995

By J. Y. Liu

In Comparison to the application of HPGR (high-pressure grinding rolls) in the cement industry and in iron ore processing, the introduction of this energy-efficient comminution technology to processing of nonferrous base-metal ores has progressed slowly as yet. In the field of minerals industry, challenges lies not only in the large variety of the feed material with respect to particle size, density, hardness, moisture and mineralogy of the material but also in complexity of the processing flowsheet, which need to be addressed from case to case based on result of HPGR comminution test work. Whereas conventional comminution test with HPGR in lab-scale or pilot scale needs quite a large amount of feed material, a compressive stressing test of particle-bed in piston-die device provides an effective way to study interparticle breakage behavior of ore material with much less feed. In the present study the effects of interparticle breakage on comminution of a copper ore has been investigated by compressive stressing of particle bed in a piston-die device. The feeds to the particle-bed stressing tests were four narrow size fractions in the size range of 0.3~3.35 mm and a broad size fraction of 0/3.35 mm. The pressures applied were in the range between 30 and 180 MPa. The results showed that the specific energy consumption increases linearly with the pressure; the product fineness increases also with the pressure, but the magnitude of this increase declines as the pressure goes up. Under the same stressing intensity, the product size distribution curve becomes steeper as the particle size decreases, so there is no self-similarity between product size distributions of different feed sizes. The suitability of a material-characterization model for interparticle breakage was verified for this ore. In addition, the effect of interparticle breakage on comminution of this ore with respect to its influence on the downstream flotation were analyzed in terms of size-metal distribution and mineral liberation.

Jan 1, 2016

By A. Abadías Llamas, N. Bartie, M. Stelter

Evaluating the economic viability as well as the sustainability of the Circular Economy (CE) system requires a deep understanding of the distribution of all elements, compounds, alloys, materials etc. in flows. In this paper, the circularity of the copper value chain, including primary and secondary processing, is rigorously evaluated. The studied system comprises the metallic copper production from primary sources (from mineral to metal), copper-containing commodity production (copper is mixed with other metals) and copper recycling through secondary smelting to close the loop. This is linked to photovoltaic (PV) panels and battery storage. A simulation model of this system is created using HSC Sim, considering more than 30 elements (and its various compounds), 180 unit operations and 800 flows. From the mass and energy balances obtained through the simulation, an exergy analysis is conducted to evaluate the resource consumption from a second law (entropy) perspective. Additionally, these results are complemented through a Life Cycle Assessment (LCA), the recovery of technology elements and by-products is discussed, while quantifying the losses through the value chain. Through the digitalization of the complete system, a better CAPEX and OPEX understanding of the metal recovery and losses can be obtained, as well as the associated resource consumption and environmental impacts. New flowsheets and technologies can be evaluated. Several scenarios show how the resource consumption and the environmental impacts are affected by the recovery of different materials to produce different products. INTRODUCTION A key challenge of the circular economy (CE) is the linkage and optimization of both resource and energy efficiency of the (renewable) energy infrastructure and the resource cycle depicted by Figure 1 simultaneously. In addition, the CE requires the linkage of all stakeholders as shown by Figure 1. This has been discussed in some detail by Reuter and Bartie (2019) and Reuter et al. (2019). Copper and all its associated technology elements is one of the key enabling metals that is an economical copper colored thread through CE society (Reuter & Kojo, 2014). The Metal Wheel (Figure 2) shows the linkage of and recovery of various elements associated with copper and other carrier metals. This reveals that copper acts as an important carrier metal because of its properties i.e. the wealth of technology elements it carries from geological ores, but also its capacity to act as solvent of valuable elements and thence a key closer of various complexly connected element and material cycles when these technology elements are released during copper refining. The same applies to all other carrier metals of modern CE society as shown for example recently in a lead policy brief (Blanpain, Reuter & Malfliet, 2019).

Jan 1, 2019

By H. J. Hartjens

"With the trend towards bringing into production ore bodies of lower and lower copper content every possible avenue of approach to achieve maximum copper metal recovery and keep milling costs to a minimum are of increasing importance.Equipment manufacturers have contributed a great deal by designing larger mills, flotation machines, pumps, etc. in lowering capital and operating costs; instrumentation and automation usually as a joint effort of operating staffs and equipment manufacturers have resulted in lower operating costs and improved metallurgy. Likewise manufacturers of chemicals used in mineral beneficiation have directed their research and development at new flotation reagents and treatment schemes to complement the needs for more efficient products, permitting coarser grinds without detriment to recovery, higher flotation rates, higher degrees of selectivity, as well as chemicals to improve settling, clarification and filtration. The various treatment schemes in use and suggested for consideration are:1) The choice of the flotation treatment scheme is largely dictated by the desire to operate a simple circuit, originally consisting of rougher and scavenger flotation, with scavenger concentrate either returning to the head of the rougher circuit or joining the rougher concentrate for cleaning by reflotation, with and without prior regrinding. The cleaner tailing was also recycled to the head of the rougher circuit. In the case of porphyry copper ores, this was originally the standard circuit. Lime is the preferred alkalinity regulator to adjust pH, usually in the range 10-12.To avoid the undesirable effects of circulating loads and gain the advantage of simplified control of the rougher circuit, open circuit cleaning is practiced more and more. In this scheme, cleaner tailing is scavenged to produce a discardable tailing and the scavenger concentrate returned either to the cleaner or the regrind circuit."

Jan 1, 1970