Search Documents

By Y. T. John Kwong

Abstract - To exploit an ore deposit without unduly impacting the environment is a challenge that can only be met by the concerted efforts of traditionally independent teams working on a mining project. Not only is detailed geology required of geologists to help mine engineers to develop a mine plan that assures generation of the least possible amount of mine waste, but metallurgists also have to select the most environmentally friendly mineral processing schemes, and communicate with environmental engineers with regard to complications that process chemicals may pose on proper mine waste management. Traditional ore deposit models typically emphasize the geological and mineralogical aspects of ore genesis to facilitate exploration for similar deposits. Recent research has shown that potential environmental liabilities such as acid mine drainage and metal leaching can readily be predicted according to deposit types. The choice of mining methods, mineral processing schemes, and decommissioning options are also largely dictated by the composition and setting of an orebody to be mined. Integrating such related information into traditional ore deposit descriptions would lead to the development of comprehensive environmental ore deposit models. The latter would facilitate communication among staff of the varied components of a mine project and aid with the selection of a combination of methods and strategies that would assure minimum environmental risks and impacts, reduce the overall project cost, and enhance sustainable development.

Jan 1, 2003

By Guohong Yin

Oxidized sulfidic tailings contain significant amounts of accumulated acidity in the form of water-soluble secondary sulfate minerals and thus constitute long-term sources of acid drainage at many metal mining sites. As part of site remediation activities, alkaline amendments are often added to the oxidized tailings to increase the pH and immobilize the metals. This study assessed the advantages and limitations of using lime mud, a byproduct of Kraft pulp mills rich in calcium carbonate (> 90 wt. %), as alkaline amendment. The inorganic and organic constituents of lime mud samples were quantified. Leachable impurities were determined by the TCLP method. The performance of lime mud was compared to that of reagent grade quicklime (CaO) and calcite (CaCO3). Tailings treated with lime mud or calcite have strong buffering capacities and remain at neutral pH conditions (pH ~ 6.7) for long times. In contrast, tailings treated with quicklime have a very low buffering capacity, and their pH decreases with time. Furthermore, lime mud has finer particle sizes and thus a greater specific surface area than most forms of commercially available calcite, which results in enhanced reactivity. Dissolved metal concentrations are similar in tailings slurries treated with lime mud or calcite. This study suggests that lime mud is an environmentally and economically attractive alkaline amendment for oxidized mine tailings.

Nov 1, 2002

By G. P. Cooper

A comprehensive computational heap leach model was used to evaluate options for operating a chalcocite-ore heap leach process. The stockpile leach model is based on the computational fluid dynamic software framework PHYSICA+ and incorporates various physical and chemical phenomena to simulate fluid transport, mineral reaction kinetics, bacterial effects, and heat, energy and acid balances for the overall leach process. The leach model is calibrated against small-scale column leach tests, and simulation results are validated against closely controlled column pilot-scale tests. For a given set of ore conditions, the effects of raffinate irrigation rate are examined. Several options for pulse leaching were investigated, and the effects on copper recovery and pregnant leach solution (PLS) grade are described. Model simulations indicated that pulse leaching could be used to control copper grade of the PLS. Finally, an analysis of inventory issues is presented for various lift heights including multi-lift simulations to examine potential operating options. U sing irrigation rate, raffinate copper grade, and lift height as variables in a factorial design of experiments, the simulations showed that raffinate copper grade is the main factor that affects the soluble copper inventory grade.

Jan 1, 2007

By Jacek Paraszczak

As the deposits located closer to the surface are getting depleted, more and more Canadian mines produce ore from considerable depths. Deep mining represents a number of serious challenges including high rock temperature. Conventional diesel powered loadhaul- dump machines and trucks so widely used in metal mines constitute an additional source of heat and noxious gases. Due to this, they have a substantial adverse impact on a quantity of fresh air required and a cost of ventilation, particularly since the mines have to meet more and more stringent regulations in this respect. In this context, the paper examines possible alternatives for diesel powered equipment, both these commercially available as those at the stages of prototypes or under development. They are reviewed with regards to their principles, required infrastructure, stage of technology development and its progress. The questions of their flexibility, practicality and economic viability are also addressed. Following the above a potential for their implementation and possible benefits (if any) in the conditions of deep Canadian mines is discussed. The paper concludes with short to medium term predictions concerning the most promising drive alternatives for vehicles destined to operate in deep metal mines.

Feb 1, 2008

By M. Schwarze

SMS Meer GmbH with its COPPER PLANTS DIVISION produces a full line of systems and machines for the processing of copper. The product range includes: shaft melting furnaces, anode casting lines, horizontal and vertical casting lines, casting and rolling lines for copper wire rod and strip, cold pilger mills, planetary rolling mills as well as tube drawing equipment. The new designed shaft furnaces are the most economic way of copper melting. The CONTILANOD® system with hydraulic shear represents a breakthrough into higher production capacities and improved geometrical accuracy of anodes. The new generation of CONTIROD® lines with individual drives of rolling stands guarantee cost effective production of highest rod quality. A new horizontal continuous casting technology for the production of tube shells as feed stock for the copper tube manufacturing process ? directube® was developed and introduced into production. A first line for continuous vertical strip casting - called VERTICAST® - for higher production rates and improval quality of cold-rollable strips is in the final stage of commissioning. These innovative technologies increase product quality, reduce process costs and help for a wide use of copper in all sectors of life.

Jan 1, 2007

By E. Roman E.

A novel anode slime purification process was developed and tested at pilot scale in the Chuquicamata Refinery. The process consists of three main stages: First, an atmospheric alkaline leaching at 90°C, under controlled pH and ORP operation parameters where metalloid impurities are preferentially removed from the anode slimes with high efficiency. In a second stage, alkaline washing of the mud leached with addition of reducing agent, with the intention of reducing the silver of the AgCl to metallic silver releasing the chloride, and finally, copper and other remaining impurities are leached out in mild conditions (60°C, one hour in sulphuric acid). In a side process Se, Te, and Sb are recovery with high efficiency from the alkaline liquor as chemical grade products. The global balance shows a high mass loss yielding a final product with high precious metal and low impurities content showing advantages in both a technical and economic point of view with a clear environmental sustainability. This treatment allows either the direct sale of the purified anode slimes or its pyrometallurgical treatment to obtain metal doré without emissions of Se, Sb and As. Chemical mechanisms for this novel process are also described.

Jan 1, 2007

By M. L. Free

Laboratory scale extraction of metals from heterogeneous materials such as copper ores is often performed using fine material to increase kinetics and reduce sample size requirements and costs. In contrast, commercial extraction is usually accomplished using much larger material sizes than are used in laboratory settings. The large size difference between laboratory testing and commercial application materials makes it difficult to use laboratory test data to accurately predict performance for commercial material. One solution adopted widely in industry is the use of large test columns. Large test columns cost considerably more to set up and run and take much longer periods of time to evaluate than laboratory scale tests with small particles. Consequently, from a cost and data collection efficiency perspective, the development of accurate scale up methods offers significant potential for saving both time and money. This paper provides details for a new approach to correct for scale-up phenomena in heterogeneous material processing.

Jan 1, 2007

By R. C. Reed, A. Akhtar

Oxidation of the third generation cast single crystal, nickel-base superalloy CMSX-10 is examined using isothermal tests at 900°C and 1000°C for times ranging from 20 hours to 100 hours. X-ray diffraction, scanning electron microscopy and energy dispersive secondary X-ray analysis were used to characterize the microstructure. It was found that the external scale formed at 1000°C is made up of (Ni,Co)O and the spinel NiCo2O4. The (? + ? ') microstructure of the superalloy transforms into the intermetallic (3 phase prior to the onset of internal oxidation. Internal oxidation results in the formation of (Ni,Co)Ta2O6 and (Ni,Co)WO4. No evidence was found for the formation of alumina (Al203), and the spinels NiCr2O4 and NiAl2O4 in this third generation superalloy. Results of the laboratory investigation are compared with those of an aero-engine turbine blade removed from service and examined earlier.

Jan 1, 2004

By Melinda Bissinger, Frederic Berube

Environmental considerations are important in the aerospace industry. To that effect, several elements such as engine emission, noise and materials are identified by the industry and the society as requiring significant improvements for future and current products in order to be aligned with current expectations. In this context, the industry is addressing this opportunity by investing significantly in new engineering solutions that will meet greener targets. To this effect, the impact of material choice is significant and will make a difference in the forth coming solutions. Several opportunities to develop more efficient products, quieter aircrafts using materials and manufacturing processes that will be more respectful of environmental considerations exist. The presentation will cover those elements and provide an overview of the upcoming solutions.

Jan 1, 2010

By O. Kangal, G. Önal, G. Bulut, A. Gül

The recovery of copper and cobalt from the ancient copper slags, located in Küre-Turkey, is investigated. Fayalitic type of ancient copper slags containing 1.41% Cu, 0.53% Co and 53.16% Fe were subject to the experimental study. Magnetic separation, gravity concentration and flotation test were conducted. The results of magnetic separation and gravity concentration were not satisfactory. However, a concentrate containing 9.57% Cu could be produced with 44.7% recovery by flotation. Copper and cobalt that remained in the flotation tailings was recovered by roasting with sulfuric acid followed by hot water leaching. Complete cobalt dissolution was observed in 1 hour of roasting at 150°C and 3:1 acid/slag ratio, whereas the copper recovery was 83%.

Jan 1, 2004

By M. R. Coffin

In recent years, improved operation of the Kidd smelter has resulted in an increase in blister production capacity. Due to manpower and equipment limitations anode production and treatment rates could not be increased without incurring significant additional operating expenses. The option chosen to expand casting and refinery capacity to meet the available blister supply was to increase the anode thickness while maintaining the same anode exchange cycle in the refinery. This has resulted in a cathode production increase of almost 10% for minimal expenditure. Equipment and process modifications required to cast and refine the thicker anodes are discussed in this paper, along with the Six Sigma methodologies used to identify them. Key areas covered are Hazelett continuous caster operation, refining process parameters, plating performance and cathode quality.

Jan 1, 2007

By K. Bunney, R. Pleysier

The deportment of a suite of elements through representative gold ore processing unit operations in cyanidation has been investigated. Chromium and lead are not soluble in alkaline cyanide solutions. Arsenic, antimony, cobalt, molybdenum, selenium, tellurium and vanadium are soluble, but typically do not adsorb onto activated carbon to any appreciable extent. Silver, copper, cadmium, mercury, nickel and zinc to varying extents report along with the gold to the carbon eluate. Cadmium, mercury and zinc can report to the carbon regeneration kiln off-gases. Strontium is soluble and adsorbs on carbon where it remgins.

Jan 1, 2011

By J. Shen

Direct methanol fuel cells have been the subject of considerable research in the last decade. Performance levels realized in cells, stacks, and systems show that this technology is a promising power source for a wide range of portable applications. A direct methanol fuel cell (DMFC) operates directly on a methanol fuel stream typically supplied as a methanol/water vapour or as an aqueous methanol solution in liquid feed DMFCs. The fuel streams in DMFCs are usually recirculated in order to remove carbon dioxide and to re-use the diluent and any unreacted fuel in the depleted fuel stream exiting the DMFC. The concentration of methanol in the fuel circulation loop is an important operating parameter because it determines the electrical performance and efficiency of the direct methanol fuel cell system. The methanol concentration in the circulating fuel stream is usually measured continuously with a suitable sensor, and fresh methanol is admitted in accordance with the signal from the sensor. There are many factors to consider in developing a methanol sensor suitable for DMFCs. These factors include sensitivity, cost, size, simplicity, reliability, longevity, concentration range, and dynamic response. In particular, reliability and low cost should be addressed. Methanol concentration sensors measure methanol concentration by means of detecting the variations of physical/chemical properties of the solution. In this work, methanol concentration sensors based on electrochemistry, electric-capacitance measurement, infrared sensing, ultrasound sensing, and other techniques are reviewed to discuss their advantages and disadvantages.

Jan 1, 2005

By S. Xu, A. Ramesh, F El-dabbagh, Z. Fang, A. Sobhy, J. A. Kozinski

Waste remediation is a goal that will be driven forward by economic conditions. As the cost of waste disposal increases, new methods of waste reduction will become economically attractive, and will be implemented. It is difficult to imagine, however, a time when there will be no waste generation. For the foreseeable future, despite effective reduction practices, there will still be hundreds of millions of tons of waste that must be destroyed or controlled to protect the public health and the sanctity of the environment. To remain faithful to environmental covenants, the mineral and metallurgical industries will face these new challenges. This paper discusses novel waste remediation approaches and techniques focusing on hazardous wastes and thermal remediation. Aspects concerning technological and environmental importance are examined. Solutions for neutralization of environmentally hazardous compounds are proposed.

Jan 1, 2004

By D. Virely, M. Gasc-Barbier, J. Guittard

"The valleys of the Dordogne and the Vézère (France) have been inhabited since prehistoric times, as evidenced by the famous site of Lascaux. A few miles away, the village of La Roque-Gageac is also a very popular tourist destination (about 1.5 million tourists per year): The village is sandwiched between a massive limestone cliff and the Dordogne river. The collapse of a cave roof high above the village in January 2010 led us to characterize instability together for the cave and the whole cliff and propose a adapted instrumentation to monitor the fracture openings in the rock mass that are linked to climatic variations. Measurements have been going on and been recorded for nearly 4 years. They point out the role of thermal stress fatigue in the breakdown of the rock mass. In this paper we describe the site under study, the instrumentation and its main results. INTRODUCTIONThe phenomenon of thermal fatigue has been very little studied as far as rocks are concerned, whereas it is rather well characterized for other types of materials: Elsevier published a journal dedicated to fatigue (International Journal of fatigue). In the case of rocks, thermal phenomena and their impacts on mechanical behavior have been analyzed from a micro-structural point of view, and it is now well-known that an increase in temperature causes a dilatation of crystals (Arnould et al., 2004; Berest & Weber, 1998). This dilatation may lead to the development of inter-granular traction and compression stresses, and if those stresses are greater than fracture strength, inter-granular and intra-granular cracks may take place. On the other hand, the fatigue phenomenon (cyclic repetition of a temperature variation which is less extreme than the one that may lead to this inter-granular or intra-granular fracture) is a phenomenon which has not been much studied.The principal studies on thermal fatigue on rocks come mainly from the field of geomorphology, particularly in connection with the analysis of the evolutions of past climate that can explain the present shapes of those landforms: those studies remained essentially qualitative and not quantitative. Le Ber & Oter Duthoit (1987) proposed a thermal and thermodynamic approach to analyse the disaggregation of rock masses. This analysis is dedicated to the study of paleoclimates and was implemented to better understand the formation of slope deposits in order to propose transfer models permitting the reconstruction of the climactic conditions contemporary to their appearance. Since deterioration in the cliff only appears after several cycles, it means that it is a gradual and irreversible deterioration which leads to an increase of the « disorder ». Seen from a macroscopic system point of view, this irreversible evolution is quantified by the internal creation of entropy."

Jan 1, 2015

By A. A. Sirkeci, M. Tarkan, N. Acarkan, O. Kangal, G. Bulut

This investigation deals with the evaluation of the tailings of the Kirka Borax Plants. In this respect boron in the tailings was recovered and the utilization of the clayish fraction was investigated. There are five tailings ponds in Kirka four of which are used for the tailings of the borax concentrator and the remaining one is used for the tailings of the sodium penta-borax plant. Experiments were conducted with samples taken from ponds containing coarse fraction and fine fraction. Coarse fraction of Borax Concentrator were screened through a set of sieves. The fraction above 1 mm was removed with 41.5% recovery and 33.3% B203 content. Scrubbing was applied above 0.1 mm and products containing 32 to 34% B203 were obtained with recoveries around 35%. The tailings of sodium penta borax plant was also screened and it was found that 15% of boron reported to +1 mm size fraction with 35% B203 content. Sample containing fine tailings was treated by cycloning. The cyclone overflow was found to be below 6µm and it was separated to be used in the subsequent tests. The usage of cyclone overflow in paper, ceramics, glass, pigment and drilling industries was investigated. Since this fraction is mainly composed of carbonate minerals rather than clay minerals it was suggested that it may be used for construction and moulding purposes. Furthermore, the B203 content of the cyclone overflow was reduced to 2.4%.

Jan 1, 2004

By M. Olper

Commercial copper plants utilising current best technology are tending towards ever increasing scale, the concentrate requirements of which cannot be serviced by a single mine. In such cases, raw materials are often sourced from different mines, which are often far away from the production plant and usually with very different ore compositions. These plants tend to use the traditional thermal processing steps of smelting, converting to blister, anode refining and casting to produce copper anodes that are then refined in a sulphate electrorefining operation. These thermal steps are in some cases troublesome and require the recycling of considerable quantities of material. A new process was developed taking advantage of the latest developments of the first thermal step of the classic loop, the smelting of copper concentrate to high grade matte or white metal using the well known AUSMELT Top Submerged Lancing Technology. The white metal and/or high grade matte product is converted directly to copper cathode and elemental sulphur using the ECUPREX technology. This approach provides an alternative to the traditional thermal steps of conversion to blister, thermal refining and anode casting, which, especially at small scale, can be expensive and problematic in terms of technical and environmental concerns. At first evaluation, this new process can be operated at low capacities, thereby, changing the traditional approach to copper production. Instead of taking the concentrate to the copper production plant, the copper production plant is taken close to the mine with some significant economic and technical advantages.

Jan 1, 2007

By T. Stergiou

An extensive research is being carried out on the shaft furnace operation in order to minimize down-times and reduce operational cost. The need to increase the scrap percentage on the charging mix, together with the need of cheaper spare parts has led to the investigation of alternative materials for the burner system on the shaft furnace. This system consists of a burner block and a flame holder. Traditionally these items are constructed either from SiC ? oxide bonded or SiC-nitride bonded. A lot of problems have been confronted over the past 8 years of operation. Usually, large cracks are formed on both flame holders and burner blocks. This resulted in leakage of combustion gases to the back of the lining and a quick erosion of it. Additionally, the burner blocks suffer from chemical erosion, due to the increased amount of scrap used in the charging mix and the presence of slag inside the furnace. Alternative materials such as stainless steel for the flame holder and alumina-chromia refractory for the burner block have been tested in terms of life-time and resistance on chemical erosion. Furthermore, additional changes have been made on the burner block design in order to alter the flame shape and improve the scrap melting operation.

Jan 1, 2007

By L. Byszynski

The results of a three month evaluation of the application of EMEW® technology at the KGHM Glogów II Smelter tank house bleed stream are presented. The current, conven¬tional electrolyte decopperization process has some limitations, including: only a fraction of its production is commercial grade cathode copper, significant operating costs, low current efficiency, low current densities resulting in low copper depletion rate, and arsine gas and sulphuric acid emission. The EMEW® cell technology developed by Electrometals Technologies Ltd. can overcome many of these limitations. Tests were performed on a pilot EMEW® installation comprising 30 cells at ambient temperature on electrolyte bleed, using current densities between 100 and 600 A/m2 , with copper concentrations between 45 and <1g/dm3. Results showed that a high grade copper can be obtained to the level of 7 g/dm3 of copper concentration in electrolyte. The use of EMEW® technology allows the direct and efficient recovery of over 85% of the copper contained in the bleed electrolyte. Glue & thiourea addition were tested in order to improve the parameters of the copper depletion process. The behavior of Arsenic and Bismuth was observed and a means for their elimination from the system proposed. On-line copper concentration monitoring is proposed to improve control and performance.

Jan 1, 2007

By P. Bonadia, A. Tabereaux

Nearly all aluminium smelters are increasing the potline amperage to achieve higher aluminium production. In some instances the higher amperage operation has a significant negative impact on shortening the lifetime of aluminum electrolysis cell cathodes due to loss of the protective sidewall cryolite ledge freeze and too rapid penetration of the cell bottom refractory lining by cryolitic bath components due to the higher temperature isotherms. Thus Cathodes require careful thermal modeling of the cathode relining designs and improved refractory materials to allow greater heat loss from the sidewall to preserve a stable sidewall ledge freeze at higher amperages, and the selection of optimum refractory barrier materials to control the penetration and reaction of bath into the cathode bottom refractory and insulation lining. This requires an understanding of the reaction mechanisms and product formation for molten NaF enriched bath and alumino-silicate refractories. It is desirable to use dense, low porosity refractory fireclay firebricks, or similar materials with a sufficiently high silica content to promote the formation the mineralogical phase albite, NaAlSi3O8, that significantly increases the viscosity of the melt which slows the diffusion of reactive species in the melt and thereby retards further bath penetration.

Jan 1, 2004