Search Documents

By V. C. Pandolfelli, S. F. Santos, L. A. Rodrigues

Under conditions of stable crack propagation at room temperature, the elastic energy stored in ceramic materials is converted mainly to surface energy. However, at high temperatures, creep may also occur in such materials, in which case it will present a ductile behavior. This paper discusses the brittle-ductile transition of a refractory material. Stable crack propagation and creep tests were carried out under a three-point bending device. A commercial ceramic containing 63 wt-% of SiO2 and 31 wt-% of Al2O3 was used as testing material. The results revealed that the change in behavior from brittle to ductile was caused by softening of a vitreous phase present in the material's microstructure.

Jan 1, 2004

By M. Roy, Y. Roux, R. McIvor

"La Compagnie Minière Québec Cartier at Port Cartier. Quebec, utilizes six parallel wet grinding open circuit ball mills to grind iron ore concentrate for the pellet making process. In an attempt to improve grinding efficiency, a mix of 605 25 mm (1 in.) and 405 38 mm (1 ½ in.) grinding balls was charged to mill D while the opposite mix was used in all the other mills. Because media costs were higher for mill D, it was necessary to find out if the smaller balls provided a net economic benefit. Therefore, a test program was undertaken to determine the relative efficiency of the charge in mill D compared to the other grinding mills. Mill F was chosen for comparative efficiency measurements.The first problem was to choose a suitable definition of grinding efficiency. In management's view, previous attempts to quantify milling performance using population balance modelling were ineffective because they were unable to relate breakage rate functions to grinding circuit economical in any meaningful way. Work index analysis was also not favoured because of a number of complicating effects, including the fineness of the feed and product streams and open circuit grinding.It was decided to adopt a recent innovative approach which had been successfully applied to closed-circuit ball milling. For ""functional performance analysis of ball milling"" (McIvor et al., 1990; McIvor et al., 1991), a size criterion is first chosen to define ""fines·' and ~'coarse particles"". In this case 45 microns (325 mesh) was chosen to distinguish fines from coarse material. The relative grinding efficiency of each ball mill environment would then be ~e cumulative grinding (disappearance) rate of coarse (plus 45 nucrons) material per kilowatt hour of energy applied to the coarse material in the mill, divided by the grindability (measured in the laboratory) of the coarse material in the mill feed.Because the disappearance rate of coarse particles is also the production rate of fines, the following equation can be written for the efficiency of the mill environment, Effe, as defined above:"

Jan 1, 1994

Mining companies around the globe have long struggled with the need to ensure that earth moving equipment is designed to be operated and maintained under all site conditions without causing harm to people. Incident and accident data from a range of sources clearly identify mining equipment related issues as major causal factors. One Australian source, the NSW Department of Primary Industries? International Mining Fatality Database Project Report (2008) noted that ?Approximately 77% of mining accidents resulting in a fatality have? involved equipment?. The largest number of fatalities were associated with trucks; the next with LHDs. Many of the technical advances in equipment design over the past few decades have not been matched by advances in the human factors design of mining equipment, resulting in a ?design vacuum? that must be filled prior to commissioning new equipment. This ?design vacuum? is generally filled by local dealers. They retrofit equipment according to customer requirements to mitigate risks that have not been designed out by the Original Equipment Manufacturer (OEM). Mining companies have been frustrated by lost time and additional costs associated with this need to retrofit ex-factory designs. Some companies have attempted to address the problem by negotiating company or site-wide ?solutions? to equipment designs, but this has not simplified or clarified the issue from the point of view of the equipment manufacturers. A number of mining companies operating in Australia first discussed the concept of a joint customer approach to improve the Human Factors design of earth moving equipment at the factory level in 2004. They agreed that a new approach to engaging with OEMs was needed; one that would define the ?Problem?, in other words, the basis of the risks, rather than dictate the ?Solution?. The Earth Moving Equipment Safety Round Table (EMESRT) was formally established in 2006 by six global mining companies to establish a process of engagement between Original Equipment Manufacturers (OEMs) and mining customers.

May 1, 2009

By M. L. F. Gameiro

The aim of this study was to check the feasibility of non-dispersive solvent extraction to recover copper from ammoniacal solutions using hollow fibres as contactors. Data of mass transfer using the B3-diketone LIX 54 as extractant was obtained. The influence of tube and shell hydrodynamics on the extraction rate of copper was studied. The overall mass transfer coefficient of copper was calculated from the experimental data by performing steady state material balance. Simultaneous extraction and stripping experiments were carried out using different volume ratios of feed phase to stripping phase. The results obtained showed that practically all the copper content was removed from the ammoniacal feed solutions. The recovery of copper reached nearly 100% in several extraction-stripping experiments.

Jan 1, 2007

By Bennett McLaughlin

The Penna Shaft is the deepest single?lift shaft in North America. AGNICO-EAGLE started sinking the Penna shaft in 1995 with a hoisting plant capable of hoisting 1 800 tonnes per day from a 2 240-metre deep shaft. Exploration success at depth lead to the replacement of the existing double drum hoist by another double drum hoist capable of hoisting 7 000 tonnes per day. The use of another double drum hoist, instead of a Blair Multi-Rope winder, to hoist 24,5-tonne skips was only made possible by lowering the safety factor. This paper describes recent experiences at Penna and in South Africa, and examines the possibility of extending the double drum hoisting system to a depth of three kilometres.

May 1, 2003

By Mauricio Olivares

About Largest combined Phosphate and Potash company in the world Corporate headquarters in Plymouth, Minnesota Publicly traded on NYSE under MOS

Aug 1, 2013

By W. Lamb

Feed Preparation ? Five primary parameters affect the screening efficiency ? Ore characteristics ? Operational characteristics ? Screen characteristics ? Water addition and washing ? System design

Apr 1, 2005

By Frederick Biery

Outline ? Project Challenges ? Results from 100 recent projects ? What factors are driving the best and worst projects ? A look at recent mining projects ? Conclusions

May 1, 2009

By Robert D. Brown

"Important tax changes, many of them of direct interest to the mining industry, were contained in the budgets brought down by federal and provincial finance ministers across Canada this spring. This month, Tax Notes presents a brief summary of important tax changes introduced at the federal and provincial levels in the last few months.IntroductionIn the March 1980 issue of the CIM Bulletin, Tax Notes surmised that the short-lived 1979 budget proposals of the former Conservative government offered a unique glimpse of budgetary changes that might be unfolded in 1980. Scene II of this ""now you see it-now you don't"" drama opened on April 21, 1980, when Finance Minister Allen MacEachen, in an ""economic statement""' reintroduced a selection of tax proposals taken from the ill-fated Conservative' budget of December 11, 1979, but refused to bring forward major new proposals in tax and finance.Mr. MacEachen proposed a 5% surtax on federal corporation income tax to apply in the 2 years from January 1, 1980 to December 31, 1981, as a slightly modified version of the same surtax proposed by former Finance Minister Crosbie in his December budget address. Mr. MacEachen also reintroduced a number of technical amendments which would affect the taxation of mining income in certain instances. In addition, a large number of other tax proposals suggested in the previous Conservative budget were also reintroduced, although there are some notable omissions."

Jan 1, 1980

During industrial copper electrowinning, a fraction of the electrolyte becomes entrained with the oxygen gas bubbles that are evolved at the anodes. The fraction of entrained bubbles increases from the bottom of the anode to the top, resulting in a bubble distribution that appears as an inverted wedge between the cathode and anode. Since the bubbles act as insulating spheres, electrolyte resistance increases from the bottom of the electrodes to the top resulting in correspondingly higher local current densities and uneven copper growth along the cathode. To counter-act the inherent tendency toward excessive copper growth near the bottom of the cathodes, the use of tapered anodes was examined. The potential improvement in cathode current distribution was evaluated by comparing the primary current distributions for 2-D computer models of a copper electrowinning cell with plate shaped anodes against one with tapered anodes.

Jan 1, 2007

By Bruno Bussière

Acid Mine Drainage (AMD) from mine wastes is one of the most environmental challenge currently facing the mining industry. AMD is the result of the natural oxidation of sulphides exposed to air and water. When mining wastes have the potential to produce AMD, these reactive wastes have to be managed to meet existing environmental regulations. The LTA site (property of Barrick Gold Corp.) contains sulphide tailings that have the potential to generate AMD. The closure option Barrick selected was to construct a multilayered cover with capillary barrier effects (CCBE). The main objective of this CCBE is to prevent the production of Acid Mine Drainage (AMD) from the tailings stack covering an area of approximately 60 ha. Since its construction in 1996, the cover has been monitored to evaluate its performance. Two of the measured parameters are volumetric water content and matrix suction. This paper presents some of the main results from the monitoring program that started seven years ago. The results show that the cover is largely able to maintain a high degree of saturation (greater than 85%) in the moisture-retaining layer. The actual performance of the CCBE on the flat surface of the 60 ha site is even better than expected at the design stage. The area that requires more specific attention with the LTA cover is the influence of slopes that can reduce the performance of the CCBE during dry periods. However, these effects seems to be local and do not significantly affect the overall performance of the CCBE to mitigate the production of AMD at the LTA site.

May 1, 2003

By Jorge Amaya

A critical aspect of long-term open-pit mine planning consists in computing a production schedule based upon a block sequencing strategy. Such a schedule should specify when and if blocks should be extracted in such a way as to maximize NPV, while satisfying wall-slope and production capacity constraints. It is well known that this problem can be modeled with integer programming (IP). However, integer programming is not used in practice because the size of typical block models makes such problems intractable to standard IP solvers. In this article we describe a scalable IP-based methodology for solving very large (millions of blocks) instances of this problem. We show that embedding standard IP technologies in a local-search based algorithm we are able to obtain near-optimal solutions to large problems in reasonable time. This methodology has been tested in several mine wide block models.

Oct 1, 2009

By Jorge Amaya

A critical aspect of long-term open-pit mine planning consists in computing a production schedule based upon a block sequencing strategy. Such a schedule should specify when and if blocks should be extracted in such a way as to maximize NPV, while satisfying wall-slope and production capacity constraints. It is well known that this problem can be modeled with integer programming (IP). However, integer programming is not used in practice because the size of typical block models makes such problems intractable to standard IP solvers. In this article we describe a scalable IP-based methodology for solving very large (millions of blocks) instances of this problem. We show that embedding standard IP technologies in a local-search based algorithm we are able to obtain near-optimal solutions to large problems in reasonable time. This methodology has been tested in several mine wide block models.

Oct 1, 2009

By Roger Reed

It is well known that the performance and carbon emissions associated with the modern gas turbine engine depend critically upon the properties of the nickel-based superalloys, particularly those used in single crystal form. However, the design of all alloys in current use has been essentially empirical, or at best heavily reliant upon regression/neural network analysis of experimental datasets. In this paper, alloy design approaches [1] are described which are able to identify new alloy composition spaces which are worthy of experimental study. It is shown that a large amount of design data can be generated, which can be interpreted in different ways. Of course, the success of the approach depends heavily upon the accuracy of the underlying sub-models. Estimates of the creep resistance, cost, castability, density and oxidation resistance are made. It is demonstrated that these methods allow quantitative trade-offs to be made between the properties of interest.

Jan 1, 2010

By G. C. Weatherly, D. S. Wilkinson, A. M. Limarga

In addition to the harsh environment, materials for high-temperature applications are often subjected to a significant mechanical loading. Several researchers have noted that the rate of oxidation can be affected by stress in a range of materials. We have recently studied this effect in y-TiAl, based on the preliminary work of Magnan and Weatherly which showed that nitridation rates on the tensile side of a flexural creep specimen could be 10 times higher than on the compressive side. We have since developed a four-point bending creep setup capable of controlled atmosphere testing. We present quantitative data on the effect of creep on scale growth under a range of atmospheric conditions. Finite element analysis will also be used to show how modest applied stresses can have a large effect on scale growth rates through the generation of large stresses due to the mismatch of creep rate between the metallic substrate and the scale.

Jan 1, 2004

By Q. Dong, S. A. Nightingale

An investigation has been carried out to assess the effects of an applied voltage on the dissolution rate of MgO refractory in a steelmaking like slag. In this study corrosion results obtained from dip tests using a dense direct bonded MgO refractory in a CaO-SiO2-Fe2O3-FeO-MgO slag are presented. These results demonstrate that the application of a voltage across a dense MgO refractory-slag interface can change the rate of refractory dissolution. For the slag composition used and the voltage range tested, it was found that a maximum corrosion rate was obtained at a voltage setting of -0.45V. The results of this investigation have been explained in terms of voltage affects on Marangoni (interfacial tension induced) stirring and its effect on the MgO dissolution reaction that is at least partly controlled by mass transfer in the slag.

Jan 1, 2004

By A. Siegmund, F. Mucciardi, Z. Yuan, B. Bulnes

With conventional heat pipe science as the starting point, a new heat transfer technology --- termed Thermopump technology, has been developed at McGill University and is now being tested at a number of industrial operations. This technology is of particular importance for transferring energy in high temperature / high heat flux environments where solutions based on current techniques are not available. One important application for this technology is in the metals recycling area wherein this technology has been used to make a waterless, non-consumable, high efficiency Thermopump oxygen lance. The viability and efficiency of this oxygen lance have been demonstrated by preliminary plant trials in a reverb furnace for the recycling of lead-acid batteries at the RSR Corporation. Full-scale commercial trials of the Thermopump (TP) oxygen lance have been carried out at the RSR Corporation. The results from these tests will be presented. In addition, some applications of the Thermopump technology for other metal recycling processes will also be discussed in this paper.

Jan 1, 2004

By W. Petruk

"D. Doyle How large is the beam to which you referred? Are we considering Watts, Griffis the probe of a 1 micron sized particle?& McOuatReply Yes. The beam would be about 1 micron. We could enlarge or reduce it depending on the current in-put.D. Doyle Then chemically bound material we might not see. If you are restricted to 1 micron then you would not be able to separate things smaller than this. Is this not so?Reply We won't be able to analyse it but we will see it as the scanning electron microscope has a resolution down to about 0.1 microns. We should be able to get the general composition of such a grain plus its surrounding grains. We feel we can then make a reasonable estimate if it were as small as 0.1 microns. An accurate analysis would be achieved with grains of 3 and 4 microns.D. Doyle Would this have an application in the hydrocarbon field?Reply The lowest atomic number would be sodium. We wouldn't be able to go below that atomic number. Anything with sodiumor a larger atomic number would enable us to analyse the carbon.M. Fairwether Do you have any policy relating to priorities. For instance areCominco companies going to be limited in the amout of samples permitted to give everyone a chance because quite frankly our company, and I'm sure all base metals companies can hardly wait for the installation of this equipment. I can forsee two years back-log of work in the first month.Reply Quite frankly, I haven't looked at this. At the present time the work is under the START program but I suppose we will have to look at possible changes. Anything under the START program has first line priority.B. Thorndycraft Will the briquetting of samples be automated as well? Pinson MiningReply No, not at this point. Our polish section laboratory is first-class and can turn out 18 polish sections a day which is more thar we can handle.B. Thorndycraft With the capability of this machine to operate in a hands-off manner perhaps it could start to look for the 5 micron gold particle in tailings?Reply I have such a program using a wave-length spectrometer rather than the energy dispersive. The wave-length spectometer is about 10 times as sensitive and would scan the section much faster. A one inch diameter polished section would be scanned in about 7 hours for anything 1 micron or larger."

Jan 1, 1984

By Jennifer Young

Presentation Outline ? Introduction ? Aboriginal Inclusiveness ? Common interpretations, practices ? Aboriginal Community Expectations ? Lessons Learned ? Native Code of Conduct Introduction Jennifer Young ? Nestu'et (Mi'kmaq) means: becoming wiser, becoming more knowledgeable Aboriginal Inclusiveness ? Internal hiring strategies (affirmative action) ? Incorporating cultural awareness programs ? Approaches in governmental/organizational policy development Practices in negotiating economic development and fiscal sharing strategies

May 1, 2010

By K. .. Sadayappan

The increasing cost of selenium made the conventional low lead alloys such as EnviroBrasses not economically viable. Efforts were made to develop newer alloys without selenium for plumbing applications. Recently a new copper alloy, C89836, was introduced. This paper discusses the properties of the new alloy including mechanical properties at ambient and elevated temperatures as well as corrosion behaviour.

Jan 1, 2007