Search Documents

By Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan

Numerical lateral load analysis based on the beam on Winkler foundation (BNWF) model (i.e., the p-y method) is a simple, and widely used tool to predict lateral responses of drilled shafts from field load tests. The lack of a site-specific p-y model for cemented soil layers such as caliche is one of the major limitations of simulating lateral load tests conducted in Las Vegas Valley. In this study, some of the existing p-y models for rock materials, such as Florida Limestone and Vuggy Limestone have been evaluated to simulate the lateral resistance of caliche. This has been done in the context of four lateral load tests in caliche-dominant sites from the recently constructed Raiders Stadium project in Las Vegas (NV). The uncertainty in characterizing the material properties of caliche has been addressed. The p-y analyses were performed using NVShaft, a MATLAB-based, comprehensive load analysis program. The applicability of the considered p-y models for caliche material was evaluated by quantifying the normalized error margins between measured and predicted lateral responses from the simulations of the mentioned load tests. Correlations between such errors and the depth and thickness of caliche in soil layers affecting numerical predictions were established, for both up to and beyond design load levels.

Oct 1, 2022

By Dominic Parmantier, Karen Dawson, Suthan Pooranampillai, Seungcheol Shin

"This paper presents a case study of the deformation-based design, construction, and performance of stone column ground improvement (GI) beneath a mechanically stabilized earth (MSE) wall and bridge abutment with heights up to 50 feet. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter- bedded with silty sand layers and organic silt where identified as being potentially liquefiable. Stone column ground improvement was designed using a deformation-based approach to address static settlement and seismic stability of the proposed MSE embankments. The deformation-based design of the stone columns resulted in significant savings over a limit equilibrium-based approach. This paper presents the results of sonic coring taken from the initial stone columns installed and compares these results to the real-time data acquisition reports from the stone column installations. Vibration monitoring results during stone column installation are included. Settlement monitoring at the face of the MSE wall and buried vibrating wire settlement monitoring elements are presented and compared to the original settlement predictions.IntroductionStone column ground improvement was implemented as a means of supporting mechanically stabilized wall approaches for a new bridge over the Puyallup River, part of HOV improvements to I-5 in Tacoma, Washington. The work discussed in this case history was part of the Washington State Department of Transportation (WSDOT) I-5/Portland Avenue to Port of Tacoma Road, Stage 1 Northbound HOV contract, developed as an early work element to a follow-on bridge construction project. The area requiring stone column ground improvement is shown in Figure 1. The improved ground supports permanent geosynthetic walls and embankments up to 50 feet high. This wall can be seen in Figure 1. The selected ground improvement primarily provides global stability of the soils beneath the walls during anticipated seismic loading and also reduces the time and magnitude of consolidation settlement under the weight of the planned embankment.Approximately 74,000 cubic yards of liquefiable alluvial soils were improved by stone columns. Stone column construction occurred in late 2010 and early 2011. This was followed by the embankment and wall construction. Settlement monitoring began with the embankment construction and continued into 2012."

Jan 1, 2017

By Karen Dawson

This paper presents a case study of the deformation-based design, construction, and performance of stone column ground improvement (GI) beneath a mechanically stabilized earth (MSE) wall and bridge abutment with heights up to 50 feet. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter- bedded with silty sand layers and organic silt where identified as being potentially liquefiable. Stone column ground improvement was designed using a deformation-based approach to address static settlement and seismic stability of the proposed MSE embankments. The deformation-based design of the stone columns resulted in significant savings over a limit equilibrium-based approach. This paper presents the results of sonic coring taken from the initial stone columns installed and compares these results to the real-time data acquisition reports from the stone column installations. Vibration monitoring results during stone column installation are included. Settlement monitoring at the face of the MSE wall and buried vibrating wire settlement monitoring elements are presented and compared to the original settlement predictions.

By Cem Akgüner

The displacements of axially loaded single piles are analyzed with an approach based on elasticity. Young?s modulus and Poisson?s ratio of the soil encompassing a pile are the unknowns required as input to obtain predictions based on the elastic method. Attention is directed towards Young?s modulus because the range and variability of Poisson?s ratio is not significant in displacement calculations. A database of axial pile load tests established for the California Department of Transportation (Caltrans) is investigated. All of the tested piles were driven into the ground. Measurements of displacements and loads were made only at the top of the pile. First the magnitude of displacements is determined up to loads that are half of the failure load measured from pile load tests. Various correlations for Young?s modulus are then employed to determine how accurately each predicts the actual measured displacement. The chosen correlations utilize the routinely available parameters of laboratory triaxial undrained shear strength for cohesive soils and standard penetration test blowcount for cohesionless soils.

Jan 1, 2008

Volume 1 pages 665-671 Title should read as Dynamic pile testing of H-piles at HDB sites J.Wei, Y. S. Heng, C. S. Lok, M. K.Chong Housing and Development Board, Singapore 'tons' should read as 'tonnes' Para 3.2 fourth equation (page 667) [TC = t2 v.dt t = 0 should read as TC = t2 v.dt - s t = 0]

Jan 1, 1994

By Jr. D'Angelo, Michael M. Blendy, Shawn Downey

"A grouted helical pile was used to support new buildings in the reconstruction of a large residential development. Foundation options were complicated by urban fill underlain with variable alluvial soil. A driven timber pile and grade beam system was recommended to support the new buildings. Other foundation options are also discussed. The grouted helical pile was quoted as an alternate and ultimately won the bid based on the economics and performance of the system. Data from 8 load tests was used to develop an empirical site specific relationship for determining pile capacity based on both installing torque and installation depth. Design to incorporate tolerance on installed pile location is presented. With the three phases completed, 554 residential dwelling units supported by 3645 grouted helical piles had been constructed covering 18 city blocks on the 44 acre site. IntroductionThe Philadelphia Housing Authority reconstructed the Tasker Homes housing complex located in southern Philadelphia, Pennsylvania, adjacent to the Schuylkill Expressway in the Grays Ferry area. Keating Building Corp. and Pennoni Associates were the general contractor and the structural engineer respectively. The original Tasker Homes development was constructed from 1940 to 1941 and consisted of 44 acres of primarily two and three-story residential brick buildings. These buildings were supported by a timber pile foundation system. The structural condition of the buildings supported on the timber piles was generally good in comparison to areas outside the buildings. These areas had settled possibly up to 2-feet in places due to the heterogeneous nature of the urban fill."

Jan 1, 2005

By Kirty Dave

Foundations in any contract are the most uncertain parts of the contract and most of the "Construction-Contract-Disputes" are either directly related to foundations or arise as 'Side-effects of changes in promises related to foundations. Foundation Engineering is defined as ' The art of selection, designing and constructing the elements that transfer the weight of structure to the underlying Soil or Rock." (Ralph B. Perk). This art started becoming a science since 1920, when scientific efforts to determine the behaviour of sub-surface materials were made. The art and science merged to give new techniques and the science started dominating the field as more and more refinement came in techniques to predict more accurately the characteristics of the sub-surface elements. Inspite of good thorough investigations and design, the contractual promises drafted could leave some room for differences between the parties and above all the prudency expected of both the parties may fall short of the expectations raised in the contract. This may give rise to disputes which may need to be resolved as per principles of law. This paper attempts to initiate a dialogue amongst Foundations-Engineers and Contractors as to how do we minimise the differences arising out of or related to contracts concerning "Foundations".

Jan 1, 1996

By Donald T. Robertson, Kurt Hecht, Michael K. Muchard

"This paper presents case histories of driven concrete pile damage detected with dynamic testing methods utilizing strain gages and accelerometers embedded in the pile at the prestressing yard during pile construction. Data from the embedded instrumentation is compared with data taken with external bolt on instrumentation and other test methods such as low strain testing on the same pile. In the most severe cases, the piles were extracted revealing and corroborating the embedded data collector results.INTRODUCTIONDynamic testing of driven pile foundations was originally developed in the late 1960’s and commercialized in the early 1970’s. While the methods of analyzing dynamic test data have improved with the advancement of computer technology, the test method and the sensors used to acquire the data have changed little. In 1998, under a research grant provided by the Florida Department of Transportation, (McVay et al, 2002) an Embedded Data Collector system (EDC) was developed. The collector utilizes two sensor packs, each consisting of one strain gage and one accelerometer, embedded near the pile toe and pile top. Utilizing the toe sensor pack, the system provides reliable real time pile end bearing capacity measurements. This end bearing capacity is combined with a Case Method Solution augmented with an automatic damping calculation to provide the overall pile capacity, pile skin friction capacity and pile end bearing capacity. Also, since the gages are embedded, they have the ability to track all changes from the casting yard (i.e. prestress), driving, and subsequent setup (freeze, relaxation, etc) at both the top and bottom of the pile."

Jan 1, 2017

By Gerald Verbeek, David Tara

"When selecting an impact hammer to drive a particular pile, the decision is often based on local experience. In those cases, the contractor falls back on previous experience or draws on the experience of the hammer manufacturer to select the hammer that will be able to do the job. Obviously, a more scientific approach would be to perform a pile driving simulation using one of several commercially available software packages (e.g., GRLWEAP, AllWavePDP or PDPWave).However, this type of analysis requires quite a bit more effort. First, an accurate model of the pile driving process has to be developed, which includes a model of the soil profile at the job site and input into the analysis program. Then, the model must be analyzed to assess whether the combination of hammer, pile and soil model work.Over the years, numerous individuals and organizations have tried to develop something that would fit nicely in between these approaches: something more advanced than a gut feeling yet something that could be done on the back of an envelope; in other words, a “Goldilocks” approach — not too simple, not too complex, but just right.Screening Tool CriteriaThe goals of the approach are twofold: (1) select the appropriate impact hammer to drive an open toe steel pipe or H-pile, and (2) then use the model for the subsequent high strain dynamic testing (HSDT). The Goldilocks approach centers around five different criteria.1. Maximum Driving StressTo minimize the risk of damage, the maximum driving stresses are generally limited to 80 to 90% of the yield stress (fy) of the steel section. This approach does not consider issues such as hammer alignment, initial imperfections, denting and/or elastic buckling, and pile material fatigue history. However, even when these issues are not applicable, limiting average stresses to 0.9fy or even 0.8fy does not necessarily mitigate the risk of pile damage (Mostafa, 2011)."

Jan 1, 2017

By Alison Savage, Michael Terry

"For decades, the International Market Place (IMP) has been an icon in the heart of Waikiki in Honolulu, Hawaii. It was famous for Duke Kahanamoku’s restaurant where people flocked to hear Don Ho sing in the ’60s and ’70s. Later, it was a bustling, open-air hub of small vendors who peddled everything from Hawaiian souvenirs and jewelry to food court meals and farmer’s market produce. Small buildings and shacks that housed the businesses were located on a curved tract of land — just one block off the beach — that stretches from Kalakaua Avenue to Kuhio Avenue. The entrance to the complex is dominated by a huge, old (circa 1850) Banyan tree. This tract is owned by the Queen Emma Land Company. Queen Emma was a Hawaiian Queen from the 1800s. Revenue from the land has supported the Queen’s Medical Center in Honolulu for decades.The reimagined IMP is owned by Taubman Centers, of Bloomfield Hills, Mich., and CoastWood Capital Group of San Francisco, Calif. The IMP will offer a distinctive collection of upscale fashion and lifestyle retailers, including Hawaii’s only Saks Fifth Avenue store, as well as ten sit-down restaurants, including concepts by award-winning chefs Michael Mina and Roy Yamaguchi. The mall features two large open-air courts, the first of which has the huge Banyan tree as its entryway centerpiece. The second open-air court, called Queen’s Court, includes a stage and mature monkeypod trees and a few palm trees. Foundation SelectionAfter a geotechnical exploration that was directed by SME, Plymouth, Mich., and performed by Geolabs, Honolulu, it was discovered that the historical site had hidden and challenging foundation conditions. The subsurface conditions included a very deep but now in-filled ancient river valley containing more than 180 ft (54.9 m) of lagoonal deposits consisting of normally consolidated plastic clayey silts and silty clays with blow counts mainly varying in N-value from 1 to 6. The silt was underlain by several soft coralline layers, some overconsolidated clays and various basalt layers. The static groundwater level on the site was at a depth of about 5 ft (1.5 m), closely matching sea level.Although driven piles had previously been used as the preferred deep foundation support for adjacent structures, this area of town is now fully developed and local noise ordinances preclude their use. Augercast piles were initially considered, but when the general contractor dck/FWF, Pittsburgh, Pa., asked for bids for the augercast piles, several foundation contractors offered alternate systems. The practical installation depth of augercast piles was limited and due to the depth of the in-filled alluvial valley, this system could likely have left soft silt below the tips of the piles over much of the site."

Jan 1, 2016

By Sepideh Damavandinejad Monfared

"In recognition of the practicality of using inclined micropiles as elements for foundation support to resist static and seismic loading conditions, specifically in retrofitting projects, this study presents an investigation into the behavior of an inclined micropile subjected to simultaneous lateral load and bending moment. Three-dimensional numerical simulations are performed using the finite element method to assess the influence of micropile geometrical parameters such as angle of inclination, length, and diameter on the response of micropile-soil system. The Mohr-Coulomb failure criterion is used to define the behavior of soil and stabilized soil around micropile materials and the micropile, constructed of concrete and steel, is assumed to be elastic. The interaction between soil and micropile is taken into account by defining interaction elements covering both tangential and normal behavior. The study is carried out using nonlinear FEM analyses. The results of these simulations indicate that negative micropiles, in which slip surface deflects downward, have higher lateral load capacity than positive micropiles with slip surface deflecting upward. The conducted research also shows that increasing the diameter and the length of micropile increases the lateral load capacity. Increasing micropile diameter is more effective in increasing lateral load capacity. A relationship is developed from statistical regression analysis of the finite element modeling computations to estimate the lateral displacement of a micropile inclined at an angle of 30o in silty sands. IntroductionMicropiles are small diameter (typically less than 300 mm), cast-in-place, drilled, and grouted replacement piles with steel pipes which after being conceived in Italy (Lizzi,1978), were originally developed for underpinning existing structures (Bruce et al.,1990) to arrest and prevent structural movement, upgrade loadbearing capacity of existing structures, repair or replace deteriorating or inadequate foundations or raise settled foundations to their original elevation."

Jan 1, 2017

By Sepideh Damavandinejad Monfared

In recognition of the practicality of using inclined micropiles as elements for foundation support to resist static and seismic loading conditions, specifically in retrofitting projects, this study presents an investigation into the beh avior of an inclined micropile subjected to simultaneous lateral load and bending moment. Three-dimensional numerical simulations are performed using the finite element method to assess the influence of micropile geometrical parameters such as angle of inclination, length, and diameter on the response of micropile-soil system. The Mohr-Coulomb failure criterion is used to define the behavior of soil and stabilized soil around micropile materials and the micropile, constructed of concrete and steel, is assumed to be elastic. The interaction between soil and micropile is taken into account by defining interaction elements covering both tangential and normal behavior. The study is carried out using nonlinear FEM analyses. The results of these simulations indicate that negative micropiles, in which slip surface deflects downward, have higher lateral load capacity than positive micropiles with slip surface deflecting upward. The conducted research also shows that increasing the diameter and the length of micropile increases the lateral load capacity. Increasing micropile diameter is more effective in increasing lateral load capacity. A relationship is developed from statistical regression analysis of the finite element modeling computations to estimate the lateral displacement of a micropile inclined at an angle of 30o in silty sands.

By Mohamed A. Mansour, Ahmed M. Soliman, M. H. El-Naggar

"Grouted helical piles allow significant increase in pile capacity with low additional cost over that of conventional helical piles. They can be particularly advantageous in sites where installation disturbance can reduce or even eliminate the pile shaft resistance. For helical piles with slender shafts, a grout column offers increased buckling resistance under compression loading, and may reduce the potential settlement required to mobilize the bearing component of their plates. This paper investigates the performance of grouted helical piles installed in loose sand. Grouted helical piles were constructed and tested in a controlled laboratory environment. Helical piles with hollow pipe shaft and single helix were grouted during installation. The grout was injected into the soil under high pressure through two nozzles placed above the piles helices. The load test results showed significant improvement in the performance and load carrying capacity of the helical pile due to the formation of a cylindrical grout column along the entire shaft leading to a higher shaft resistance contribution to the total pile capacity. The results suggest that grouted helical piles with slender hollow shaft could be used to support large structural loads. INTRODUCTIONHelical piles are widely used as a deep foundation system for different engineering applications. They represent an attractive foundation option because of their cost effectiveness, ease of installation even in limited access areas, low levels of noise and vibrations, and their ability to be installed through ground water without casing. In addition, they allow immediate loading upon installation. Helical piles are installed into the ground by applying a mechanical torque to the pile head. The installation torque monitoring provides a kind of quality control during the construction of helical piles. It could be used in predicting the ultimate pile capacity using several capacity-torque correlations (Livneh and Elnaggar 2008; and Hoyt and Clemence 1989).However, helical piles installation can cause soil disturbance within the annular zone affected by the pile helices. This disturbance can introduce fissures within the pile cylindrical failure surface (Vesic 1971; Mooney el al. 1985; and Zhang 1999). Thus, the shear strength of the soil decreases along the affected zone. Bagheri and El Naggar (2013) evaluated the installation effects of helical piles in sand. They reported that as the helical blade proceeds into the ground, sand within the cylindrical path circumscribed by the helices experiences torsional and vertical shearing accompanied by sand displacement and stress changes. This process is more pronounced in the case of multi-helices and large diameter anchors. Bagheri and El Naggar (2016) evaluated the installation effects of helical piles in structured clay. They indicated that the behavior of the helical pile and its capacity are significantly affected by the degree of soil de-structuring induced by the penetration of the pile shaft and helices. In addition to the installation disturbance, helical piles have other drawbacks including; high potential settlement required to fully mobilize the bearing component of their plates, low buckling resistance of their slender shafts, and the incomplete rigidity of the coupling joints along the pile shaft that allow some lateral movement under compression loading (Vickars and Clemence 2000)."

Jan 1, 2016

By Toshio Yonezawa, Helmut Florian, Herbert Kuh, Masamichi Aoki, Takao Koono, Franz-Werner Gerressen

"To increase the bearing capacity of the ground, soil improvement technique is often adopted. One advantage of soil improvement techniques is the fact, that the impact to the environment is low, as the system utilizes the existing soil. Recently, compressive strength of soil improvement gets more into the focus for the use of building foundation. To prevent brittle fracture, which is a weak point of soil improvement, fiber reinforced soil improvement has been developed. Laboratory tests were conducted to examine the fibers suitable for reinforced soil improvement, and examine the optimum mix design for fiber cement slurry. Based on the laboratory tests, polypropylene fiber and cellulosic viscosity admixture was selected. For the laboratory tests a scaled model of CSM mixing head was used to examine the dispersion of the fibers in the ground. Using the CSM mixing head, the outer periphery fibers of soil improvement seemed to be arranged in the vertical direction, toughness performance of the soil improvement could be improved. Furthermore, full scale field test was performed using actual CSM unit, modified to enable the use of fiber mixed slurry. The validity of the material as well as the toughness performance of the soil improvement, determined from lab test results, was confirmed. In addition, it was confirmed that fiber reinforced soil improvement can be constructed appropriately by CSM method.2 INTRODUCTIONSoil improvement technique to improve the strength and deformation performance of ground has been used for a long time. Cement improved methods, with the increase of the deep Mixing Method, which has been disseminated since the 1970's, was often used since. Cement used soil improvement technology has been utilized to stabilize excavations, slopes in embankment and much more. Recently, it can be used for preventing liquefaction by building soil improvement in a grid (Suzuki et al. (1996)), and also as basis of the structure by increasing the compression strength of soil improvement (Yamashita et al. (2011)). Cement used soil improvement method, a technique for mixing the in-site soil and cement, can effectively utilize natural resources, and it can be expected that its use will increase further in the future. Therefore, soil improvement technique will be able to minimize the impact on the environment. Cement improved soil is a mixture of soil particles and cement with high compressive strength but low tensile strength. Since tensile strength of soil improvement is low, brittle destruction occurs. Therefore, it is not possible to use soil improvement in conditions acting with bending stress. If a horizontal impact force occurs in the improved soil, the width of the soil improvement needs to be increased to reduce the bending stress. If preventing the brittle fracture of soil improvement, the width of soil improvement could be reduced, then less resources would be needed. In order to increase the tensile strength of the soil improvement, several studies for the mix of fiber and soil were performed. Victor (1992) indicates cracking deterrent effect by fiber based on laboratory tests. Moreover, based on laboratory tests, Hayasaki (1982) illustrated the effect on the tensile strength of the fiber types, the type of fiber, the diameter of and the length of fiber."

Jan 1, 2015

By Dale Berner, Michael O’Sullivan

"This article focuses on lessons learned from innovative designs including in-the-wet construction methodology and modified foundation conditions, for two United States Army Corps of Engineers (USACE) megaprojects. Olmsted Dam FoundationThe over $2 billion Olmsted Dam on the Ohio River is currently under construction 16 mi (29.6 km) upstream from the confluence with the Mississippi River. The project is under the jurisdiction of the Louisville District of the USACE. It will consist of an 800 ft (244 m) long tainter gate section, a 1,400 ft (427 m) navigable pass, two boat abutment sections, a fixed weir section, and upstream and downstream scour protection. The Olmsted Dam and its two 1,200 ft (366 m) locks, which were built in 2002, will eventually replace both Locks and Dam #52 and #53, both built in 1929, and thereby bring significant benefits to the Ohio River navigation system.In 2002, the Jacobs/COWI JV completed the design of the dam; which was an engineering challenge for several reasons. A significant consideration was its proximity to the New Madrid Fault, which could impose an 8.4 Richter scale seismic event on the structure, which is located in an area of potentially liquefiable alluvium. The extensive seismic analysis performed by the designer included a response spectra analyses, lateral pushover analyses of pile foundations, hydrodynamic added masses, pile group effects, and the development of kinematic motions as a result of the soil-pilestructure interaction."

Jan 1, 2016

By K. Rainer Massarsch

"Part 2 of 2 (Continued from Summer 2004 edition) By K. Rainer Massarsch, Geo Engineering AB, Stockholm, SwedenVibrations, which are caused by the installation of piles in dry or permeable soils, can cause settlements. The magnitude of settlements depends on several factors, such as soil type and stratification, ground water conditions (degree of saturation), pile type and method of pile installation (driving energy). A method of settlement prediction due to construction-induced vibrations has been presented by Massarsch (2000). However, in many cases, an engineering assessment must be made at an early stage of a project. The following simplified procedure can be used to estimate settlements in a homogeneous sand deposit adjacent to a single pile, Fig. 5. This approach is based on extensive experience from soil compaction projects. It is assumed that intense densification due to pile penetration occurs within a zone corresponding to three pile diameters. The volume reduction resulting from the propagating vibrations will cause settlements in a cone with an inclination 2V:1H, with the tip at a depth of 6 pile diameters. Thus the settlement trough will extend a distance of 3D+L/2 from the centre of the pile, with maximum settlements at the centre of the pile. Maximum settlements, Smaxand average settlements, Smax can be estimated using the following relationship, choosing an appropriate a value of the soil compression factor, from Table 2.The driving energy depends on the method of pile installation, soil stratification and the pile type. The displacement volume of the installed pile has been neglected. The simplified method is applicable for estimating settlements at the perimeter of a pile group. It should be noted that settlements also occur outside the assumed cone, but these are often negligible. The effect of incompressible layers should be taken into account by adjusting the effective pile length."

Jan 1, 2004

By Gokhan Inci

Stability problems with dam spillways on existing landslides and appropriate mitigation measures to remedy them are ongoing concerns for geotechnical engineers. The first successful application of drilled piers as stabilizing structures under the spillway was at the Trinity Dam in Sicily, Italy. ?Underpinning? was considered as an alternative to spillway relocation during the Alpaslan 2 embankment dam design in eastern Turkey. Based on the available literature the first application of drilled piers to stabilize a spillway chute in the U.S. was at the Ralston Dam in Colorado. Ralston Dam, which is a 175-foot-high zoned fill dam located 15 miles northwest of downtown Denver, was built in the late 1930s. The concrete spillway for the dam was built on the Pierre Shale Formation in the left abutment. Since reservoir operations began, mass movements have occurred downstream of the chute area. These movements have required periodic spillway maintenance. After the occurrence of recent movements and because of high piezometeric levels, URS was contracted by Denver Water to develop a more permanent solution by the installation and monitoring of additional instrumentation, analysis of slope stabilizing measures, design, repair, and reconstruction of the distressed section of the spillway chute. With state of the art modifications that include: 1) a stabilizing berm with a toe trench that improves the global stability; 2) seepage prevention and control measures that prevent the infiltration of water; and 3) the structural support of the replaced chute section with drilled piers and reinforced concrete the probability of future displacements or other problems have been reduced for the Ralston Dam Spillway.

Jan 1, 2007

By Donald T. Robertson

This paper presents case histories of driven concrete pile damage detected with dynamic testing methods utilizing strain gages and accelerometers embedded in the pile at the prestressing yard during pile construction. Data from the embedded instrumentation is compared with data taken with external bolt on instrumentation and other test methods such as low strain testing on the same pile. In the most severe cases, the piles were extracted revealing and corroborating the embedded data collector results.

By Adrian M. Keller

Borehole televiewers are downhole inspection devices available for high-resolution imaging of a borehole wall following rock coring. Borehole televiewers should be considered by geotechnical engineers and geologists as a supplemental way of investigating rock for deep foundations. The optical televiewer (OTV) produces a digital optical image and the acoustic televiewer (ATV) utilizes reflected acoustic waves to produce images of the borehole walls. These devices can be utilized to examine soft or fractured zones in the rock mass, solution features, open joints or other voids not observable from traditional rock coring techniques. These devices along with computer post-processing can determine the strike and dip of joints, bedding planes, shear surfaces, or other structural features, eliminating the need for expensive oriented cores or manned downhole logging. An acoustic televiewer was utilized in the Fall of 2008 during the investigation phase for the I-70 New Mississippi River Bridge (I-70 MRB) in St. Louis, Missouri. Voids and fractures in the upper portion of the rock were described by prior consultants. Further investigation of these features was necessary to evaluate deep foundation options to support the main towers. Ten borings were drilled from a barge in the river at the two main tower pier locations. An ATV was utilized in each of the ten borings to produce images of the rock mass in the borehole and allow further investigation of the voids. Voids interpreted as solution features were readily identified in the ATV logs in multiple borings and at similar elevations, suggesting connectivity. Measurements of the voids? width, location in the borehole and orientation allowed a more thorough understanding of the potential impact the solution features may have on the planned deep foundations. An extensive grouting program was eliminated based on the ATV results.

Jan 1, 2010

This paper summarizes seven years of Italian ex­perience with the use of large calibration chambers for the calibration, under closely controlled stress and strain conditions, of some in situ testing devices which are used in sand deposits. At the present time two calibration chambers are operating in Italy, one at E.N.E.L.-C.R.I.S. (Milan) (*) and the other at I.S.M.E.S. (Berga­mo) (**). Both chambers can accomodate cylindrical samples 1.2 m in diameter and 1.5 m in height. A detailed description of these chambers can be found in Bellotti, et. al (1982).

Jan 1, 1987