Search Documents

By Hamed Ardalan, Mohamed Ashour

"CHAPTER 1INTRODUCTIONThe use of piles to stabilize active landslides or to prevent instability in currently stable slopes has become one of the most important innovative slope reinforcement techniques over the last few decades. Piles have been used successfully in many situations in order to stabilize slopes or to improve slope stability, and numerous methods have been developed for the analysis of piled slopes (Ito et al., 1981; Poulos, 1995; Chen and Poulos, 1997; Zeng and Liang, 2002; Won et al., 2005).The piles used in slope stabilization are usually subjected to lateral force through horizontal movements of the surrounding soil; hence they are considered to be passive piles. The interaction behavior between the piles and the soil is a complicated phenomenon due to its 3-dimensional nature and can be influenced by many factors, such as the characteristics of deformation and the strength parameters of both the pile and the soil. The interaction among piles installed in a slope is complex and depends on the pile and soil strength and stiffness properties, the length of the pile that is embedded in unstable (sliding) and stable soil layers, and the center-to-center pile spacing (S) in a row. Furthermore, the earth pressures applied to the piles are highly dependent upon the relative movement of the soil and the piles."

Jan 1, 2013

By Paul J. Sabatini

Between 2008 and 2009, more than 6,000, 23-m long deep mixing method (DMM) elements were constructed to support 124 concrete mats comprising the foundations for the process trains for an LNG facility. The Owner requested first-of-its-kind analyses and assessments to confirm the quality and reliability of the DMM foundation. This paper provides information on these assessments and the procedures used to ultimately conclude that a fit-for-purpose foundation system was constructed. During early phases of construction, several DMM test cores revealed nodules of unmixed clay in upper core samples. A comprehensive review of available DMM core information was undertaken. It was concluded that the amount of coring being conducted as part of the contractor?s QA/QC program should be increased to achieve a foundation system with the required level of reliability. Three-dimensional finite element analyses were completed considering various distributions of defects in the DMM elements and the effects of potential downdrag on DMM elements. Calculated mat settlements and mat stresses were compared to cases without defects in the DMM elements. Various distributions of loaded and unloaded mat areas and number and position (both in the subsurface and laterally) of defects were considered. Four (of the 124) mats were identified as potentially ?at-risk?. The settlement performance of these mats is currently being monitored and, to date, performance has been acceptable.

By Bryan C. Field

The proposed construction schedule for the St. Anthony Falls I-35W Bride challenged the abilities of the design-build teams to utilize the best and most efficient methods to meet Minnesota Department of Transportation?s deadlines and design requirements to restore traffic to the Interstate 35W crossing of the Mississippi River, along with a sense of normalcy, following the bridge collapse. The project team ultimately designed and constructed two foundation systems at various substructures for bridge support. Steel H-section piles were driven to bedrock for south bridge abutment support and drilled shafts were used for the north bridge abutment and piers for the Mississippi River Bridge. Drilled shafts we also used for the abutments for the three single span bridges carrying I-35W over 2nd Street. The design-build team used high-strain dynamic pile testing with a Pile Driving Analyzer (PDA) to verify H-Pile capacities and performed drilled shaft inspection on a 24-hour basis during installation over the winter months. The drilled shaft inspection process was a vital part of the project quality control program to maintain the necessary methods for proper drilled shaft installation. Ultimately, with an efficient design, quality construction methods and operation, and a rigorous inspection and quality control plan; the I-35W Bridge was opened to traffic 3 months ahead of the already accelerated schedule.

Jan 1, 2009

By A. Felipe Uribe-Henao, Camilo Ballesteros, Luis G. Arboleda-Monsalve, David G. Zapata-Medina

Conventional excavation analysis based on total or effective stress methods can result in inaccurate estimation of ground movements when impervious soil conditions or rapid excavation sequences are not found in the excavation (i.e., assumption of undrained response is not valid). The influence of excavation rate, hydraulic conductivity, and excavation geometry on the fully coupled solid-fluid behavior of a braced excavation in cohesive soils are studied parametrically using PLAXIS2D. The coupled excavation analysis is performed using the Hypoplasticity clay model to reproduce the constitutive behavior of soil and the poro-elasticity Biot’s theory to account for changes in pore water pressure due to deformations in the soil skeleton. Results obtained from the parametric studies indicate that excavation rates to hydraulic conductivity ratios, ER/k, smaller than 0.1 and larger than 104 can be used as limits for drained and undrained analyses, respectively. In practical applications, undrained and partially drained excavation analysis with ER/k larger than 102 resulted in a similar ground deformation. However, smaller ER/k ratios demand fully coupled solid-fluid analysis. An analytical method aimed at predicting excess pore water pressures and determining the required type of analysis associated with soil and excavation conditions, e.g., drained, partially drained, and undrained analysis, is proposed herein to accurately estimate the ground movements induced by the excavation.

Pier, well cap and steining junction is a complicated 3-d re-ion. The prevalent design procedure for the pier, well cap and steining in isolated manner is not rational. In absence of an integrated approach for design of the junction structure, the well cap is designed uneconomical and at the same time pier and steining are left relatively unsafe. Strut-and-Tie Model based design is a simple solution to this problem. An example illustrating design of the junction structure using STM is presented. On comparison of the outcomes of the STM based design with the prevalent design, the following anomalies are found: i) For smooth flow of forces, length of pier at its base should preferably be made equal to the outer well diameter, ii) STM based design for the pier is more rational, economical and safe. iii) Due to presence of hoop stress, as indicated by the STM, the steining concrete in a depth of p times outer diameter of the well from the well cap level should be limited to M15 grade, iv) STM based design for the steining is more rational, economical and safe.

Jan 1, 1996

By Bora Okumusoglu, Devon K. V. Mothersille

"AnchorTest is an innovative software package, specifically developed for tablets, that permits ground anchor test data assessment and management in real time. The solution has two components: a front-end tablet app runs on the Apple iPad platform, and a back-end Cloudbased system running on Amazon Web Services with an online cross-platform website, which can be accessed from any PC, tablet or even mobile smartphone. This tool provides full data analysis and data management capabilities and portability to create greater efficiency in the anchor testing process. AnchorTest is programmed to accommodate the major international anchor testing codes and incorporates an intuitive user interface, which is revolutionary compared to conventional engineering software designs. The use of this tool creates an environment where the testing of ground anchors has effectively become a paperless exercise with greater efficiency and access to instantaneous feedback on the performance of anchors in relation to established acceptance criteria.Historically, project personnel record and analyze the results from anchor load tests using spreadsheets and a laptop computer and/or on predesigned paperbased test sheets (usually as a backup of the testing). In addition, the processing of the test results is not typically performed in real time as the testing progresses — the calculations and analysis are performed either afterward while still on site (if a field office is available) or after returning to the office. Undoubtedly, on larger projects containing numerous anchors where multiple anchor tests may be performed at the same time, processing, analyzing and accepting the load test data and results can be especially time consuming, which could cause delays to the construction schedule.DevelopmentThe need for a more automated and digitized approach to record, process and analyze the data from anchor load tests was highlighted at a deep basement project for a mixed-use development complex in Moscow, Russia. The diaphragm wall supporting the structure was approximately 1,970 ft (600 m) in perimeter length and about 148 ft (45 m) deep, with an excavated depth of about 82 ft (25 m), which required six levels of single bore multiple anchors (SBMAs). This project provided a challenge to recording, processing and signing off on the data generated from some 3,600 3-unit SBMAs. More specifically, for this project, three hydraulically synchronized stressing jacks were used to stress and proof test each 3-unit SBMA, which resulted in nearly 10,800 data plots of the load-extension tests being generated. This project served as the main impetus in the conceptual design and optimization of AnchorTest."

Jan 1, 2017

By S. Y. Zhou

Excavation with earth retaining is one of the main technological means in deep foundations and underground engineerings. Several construction methods which have been used in China are introduced here with some examples from engineering practices in Shanghai, including foundation pit protected by steel or RC sheet piling or D-walls, open caissons and pneumatic caissons, shield tunnel and pipe jacking, etc. This paper also discusses the prospect in development and utilization of underground space in China and the challenge to which the engineers specialized in deep foundations have to face.

Jan 1, 2010

By RAP Bement

Installation by vibrodrivers of sheet and bearing piles generates periodic vibrations in the surrounding ground, which have been widely measured and reported. One of the possible consequential effects of these vibrations is ground settlement caused by the compaction of loose granular soils. Vibratory compaction settlement of a range of granular soils has been studied in the laboratory using a 150mm diameter Rowe cell, which allows sample preparation and control during vibrations equivalent to conditions in the field during vibrodriving. The cell containing the soil sample was mounted on an electromagnetic shaker and vibrated at amplitudes and frequencies appropriate for soils adjacent to vibrodrivers. The changes in sample height were recorded.

Jan 1, 1996

By G. G. Meyerhof

The paper reviews the state of the art of estimating the bearing capacity and settlement of pile foundations in sand and clay soils, including the effects of pile installation, scale effects of pile size and embedment and non-uniform soil conditions. The lateral resistance of pile foundations and effects of eccentricity and inclination of the load on the bearing capacity and movements of pile foundations in sand and clay are considered on the basis of some recent investigations.

Jan 1, 2010

By Masaki Kitazume

Five papers were presented orally to the topics of Jet Grouting and Deep Mixing. The session was started with a brief introduction by the moderators. Following the oral presentation, floor discussions were directed by the moderators. A brief introduction of each of the oral presentations is provided before each discussion.

Feb 10, 2003

By Alan G. MacKinnon

The current piling practices in the U. S. have, to a great degree, been influenced by our founding fathers. When our constitution was written by the delegates from the original thirteen colonies, it was a document of compromise. Generally, the individual states retained their sovereign power over those duties that they had historically performed. The concept of States Rights has been tested throughout our history and has been preserved as of today. An example of the extent of this protection is occurring in the State of Ohio where I currently live. Each of the 50 states receives funds for highway construction from the federal government, approximately in proportion to its population. Congress, when it allocates the funds, quite often attaches amendments to the funding bill to exercise their authority. The major amendment prior to the most recent increase in the speed limit to 65 mph from 55 mph was to increase the legal drinking age to 21 from 18 years old. Embodied within the bill was the provision that the Federal government deduct a percentage from the allocation of any state that did not revise its legal drinking age law from 18 to 21. In the State of Ohio, this change in the law was put to a vote of the people and it was defeated. The federal government now is deducting funds

Jan 1, 1987

By Dale E. Berner

A new navigation dam at Olmsted on the Ohio River will be built "in-the-wet" using a lift-in construction method by the Washington Group/Alberici Joint Venture for the U.S. Army Corps of Engineers, Louisville District. Up to 4,000-ton precast concrete dam shell segments will be prefabricated on the Illinois riverbank and lowered into the river on a marine skidway and cradle. A 4,500-ton capacity catamaran crane barge will lift the precast concrete shells and lifting frames from the cradle, and transport them partially submerged to a piled foundation pre-installed underwater. Tremie concrete will be used to compositely connect the shells, piles and sheet pile cut-off walls. This paper focuses on the pipe-pile foundations for this half-mile long navigation dam, and for the temporary precast yard and marine skidway. The dam foundations are designed to resist large ground motions from the New Madrid Fault Zone, and selected production piles are designed to serve as landing piles to support the shells during the construction process. Specific foundation issues addressed in the paper include: pile load tests; production field testing requirements; controlled fixity 24-inch diameter pipe-pile design including seismic considerations; cut-off wall design; sheet pile cellular fixed weir design; isolation jOint design; and temporary works foundation designs for both the precast yard and the marine skidway, including testing of 42-in diameter pipe piles.

May 11, 2007

By Bernardo J. Jiménez, Harlem Lora, Roberto Acosta Mora

Circunvalacion Norte project is currently the most important infrastructure project in Costa Rica. It is the last segment of the urban perimeter highway. Site investigation of local geotechnical conditions were studied by SPT, CPT, pressuremeter tests and boreholes. A static load test was executed as a proof test with an associated ultimate resistance of 12056 kN (2710 kips). Drilled shaft design was done using PMT tests and axial nominal resistance varied between 4000 kN (900 kips) and 6000 kN (1350 kips). A total of 416 drilled shafts were constructed in 15 months with drill performance of 32 m/day (105 ft/day). Drilled shaft lengths varied between 4,0 (13 ft) m and 40,0 m (130 ft). Selfconsolidating concrete was used to achieve an adequate workability even in high densities rebar cages. Several site conditions proved the importance for maintenance of the working platform, predrilling of rock sockets and having spare parts to avoid increase in project’s cost. New procedures were taken to prevent concrete segregation on excavations near underground water flow. Monitoring the quality of the shafts from CSL test showed less than 3% of the shafts presented a considerable anomaly, which proved that the adopted construction method and materials were adequate. For the concrete anomalies, successful remediation was performed by means of grout at the base of the shaft with two different types of drilling methodology depending on the concrete anomaly.

By David R. Black

Foundation problems due to collapsible and expansive soils are well known throughout the arid western United States. Millions of dollars are spent annually to counteract the effects of such soils for both new foundations and existing foundations suffering from settlement or heave. Over the last 20 years helical screw piles have come into wide-spread use as a permanent deep foundation element for these problem soils, especially in the arid western United States where, in some areas, they are a standard of practice. Independent research resulting in recognition by every national building code in the United States has legitimized helical screw pile technology. Once thought of in terms of light structural underpinning, helical screw piles of today are designed to take heavy structural loads, vertical and lateral, tension or compression, including seismic loads. With proper pile grouping, design capacities for column loads over 4,500 kN (1,000 kips) are attainable. This paper discusses design considerations specifically dealing with collapsible and expansive soils: soil investigation parameters, predicted settlement and long-term creep, heave in expansive soils, downdrag in collapsible soils, shaft slenderness buckling, maintaining shaft alignment during installation, refusal condition, water migration along the shaft, lateral loading, cyclical loading for seismic loads and machine foundations, corrosion, helix durability during installation, the installation torque vs. capacity equation, and design methodology. The paper concludes with several case histories where helical screw piles were used for new structural foundations and to underpin existing failed foundations in St. George, Utah, Cedar City, Utah, and Denver, Colorado, USA, sites of some of the most expansive clay and collapsible soil in North America. Soil descriptions and performance histories are presented.

Jan 1, 2002

By Jennifer Peirce Brandt

Project documents and the United States Army Corps of Engineers? permit for construction of the Stemmers Run Relief Wastewater Force Main across the Back River in Baltimore County, Maryland specified a minimal width, steel sheet pile cofferdam and a 12 feet wide, pile supported, timber decked, causeway trestle ? both approximately 1700 feet in length. Due to the impractical width of the causeway, the contractor desired to combine the cofferdam and the causeway structures in order to minimize wetland disturbance and maximize access for construction equipment. The resulting support structure was a steel sheet pile cofferdam, approximately 17 feet wide, internally braced, and capped with transverse timber deck mats to serve as the access and work trestle for the trench excavation, pipe bent construction, and trench backfill. Construction of this cofferdam/causeway progressed from the north shoreline toward the middle of the river. Then, working back toward the north shoreline, the contractor excavated, installed the 54 inch diameter pipe and H-pile support bents, and backfilled the trench in increments of approximately 60 linear feet. Excavation spoils from one section were used to backfill the preceding section. As the pipe installation progressed toward the north shore, the steel sheet piling and timber deck were removed. As sufficient sheet piling and deck mats were removed, the contractor began the process anew from the opposite shoreline using the reclaimed materials. The project was complicated by the presence of deep, very soft, weight of hammer, silts and organic clays and an unbalanced, hydrostatic head of 20.5 feet. In addition, concurrent pile driving, excavating, and backfilling in successive cofferdam sections required the use of heavy, long reach, hydraulic backhoes, and a 200 ton capacity crawler crane which controlled the design of the timber causeway deck and its supporting sheet piles.

Jan 1, 2008

By Frederick C. Rhyner

The United States government sponsored the construction of a new vehicular bridge over the Diyala River in Bubriz, Iraq. This paper describes the geotechnical engineering for design and construction of drilled shaft foundations for this bridge. An Iraqi geotechnical engineering firm made borings and laboratory tests while analysis and design recommendations were provided in the United States. Despite the severe challenges of engineering in a war zone, excellent cooperation was the key to a successful effort. Three drilled shafts designs were necessary to accommodate the different subsurface conditions: a) medium-compact to compact sands, b) stiff to hard clays and c) mixed soil profile. The alpha and beta methods were used to estimate capacities for a conservative design, recognizing that quality control during construction might be less than what is normally provided in the United States. Iraq has a high seismic risk and LPILE was used to estimate the drilled shaft response during earthquake loading conditions. Settlement estimates were made using FHWA methods. Construction was carried out entirely by local Iraqi firms, despite the challenges of working in an active conflict area.

Jan 1, 2009

By J. P. Powers

Methods for dewatering and the control of ground water for construction and mining are discussed, including open pumping; predrainage with deep wells, wellpoints or other systems; cutoff or exclusion of water by steel sheet piling, slurry concrete walls and slurry trenching, grouting, ground freezing, compressed air, slurry shields and earth pressure balance shields. Criteria are given for the selection among the methods for a given project. Unwanted side effects of dewatering are listed, with procedures for evaluating and avoiding them, by cutoff or artificial recharge.

Jan 1, 2010

By Michael W. Oakland

This paper summarizes the analysis and design of a pile foundation system for two 400 ft. diameter, 500 ft. high cooling tower using a detailed finite element analysis package. The cooling towers are at the Brayton Point Power Plant in Somerset, Massachusetts. The design-build project will convert the power plant to a closed loop cooling system to reduce return of heated water to the bay. Each cooling tower is supported on a 5 ft. thick by 16 ft. wide ring beam with 44 columns oriented in a radial pattern. The allowable lateral movement on the thin wall shell was limited to only 0.5 inches. Lateral and tension resistance were the primary concerns for the large, but lightweight structure and the critical issue was the lateral response of piles and pile groups within the system. By constructing a detailed model of the foundation system including modeling each pile as an independent element, the contribution of each element was separately assessed and the system tuned to take best advantage of the load distribution afforded by the ring beam as well as the soil structure interaction created by tangential as well as radial resistance of the pile groups. The detailed model also incorporated the lateral resistance of interior piles supporting an equipment slab within the ring beam. Simpler models analyzed the pile groups independent of the complete structure and generally only relied on radial stiffness and generally resulted in large groups of piles needed at each pier. Through a series of trial configurations, the number of piles used was optimized. Confirmatory lateral, vertical and tension load tests were conducted and final fine tuning of the model completed.

Jan 1, 2010

By Kyle L. Murrell

Along the southeast United States coast, clayey silt and silty clay marine formations may cause pile installation and integrity problems. More specifically, excess pore pressures which develop in these soils during driving can cause high displacement piles to rebound or ?bounce?. Bounce is defined as a large (¾-in. to more than 1-in.) downward pile displacement during the hammer blow with little to no net displacement at the end of the blow. Pile bounce can generate damaging tension stresses and result in inefficient pile installation. A case history is presented where pile bounce was observed during the installation of 20-in. square ?high displacement? prestressed concrete piles which support a new ferry terminal in coastal North Carolina. High-strain dynamic pile testing was performed during test pile installation to evaluate driving stresses, pile capacities, and hammer performance. During and after installation of numerous production piles, circumferential cracking was observed on some of the piles. Additional high-strain dynamic pile testing was performed on two piles installed with a hammer having a heavier ram than the initial hammer. The new driving system generated lower tension stresses and installed the 20-in. piles more efficiently. Low-strain integrity testing was performed on the piles to qualitatively assess the cracks and locate any unidentified cracks. The low-strain testing was performed on piles installed at least a week prior to testing and on piles installed immediately prior to testing. When low-strain testing was performed immediately after pile installation before dissipation of excess pore pressures, pile integrity could be evaluated to depths of at least 12 pile diameters deeper than when performed weeks after installation.

Jan 1, 2008

By Ruth McKeown, Gilson de F. N. Gitirana, Murray Fredlund, HaiHua Lu

The current design standards for the use of anchors in slopes is based on two-dimensional (2D) limit equilibrium analyses. Anchors are considered as discrete loads and the 2D anchor, factored based on the spacing distance, corresponds to extending anchors indefinitely in the third dimension. A three-dimensional (3D) analysis offers a more realistic representation of the problem, including the true discrete nature of the anchor point loads. This paper explores the typical differences between analyzing anchors in 2D and 3D, using four typical conceptual models. Slopes with constant cross sections were shown to be adequately represented by the traditional 2D approach. The maximum difference between 2D and 3D models was 21% and becomes negligible for lower anchor spacing values, as expected. A slope with an external load was analyzed to evaluate critical slip surfaces with lower aspect ratios. Slip surfaces with lower aspect ratios presented higher edge effects that contributed to the stability of the slope. The results indicate that optimum design requires the 3D evaluation of field conditions inducing low aspect ratios, such as concave and convex surfaces, weak layers, and external loads. INTRODUCTION Slopes may be stabilized using a variety of solutions, including anchors. When performing an analysis, geotechnical engineers often follow the traditional two-dimensional (2D), Limit Equilibrium Method (LEM). It is important to understand the consequences and limitations of the assumptions on which the 2D LEM is based. There are numerous studies on anchors that show the importance of considering the actual three-dimensional field conditions. Desai et al. (1986) proposed a three-dimensional procedure based on the Finite Element Method and considering elastoplastic behavior and interface elements, to account for stress and displacement distributions, the relative motion between the anchors and the soil mass, and nonlinear soil behavior. Several important stabilization mechanisms were explained. The role of grout injection was evaluated in terms of the produced normal stresses along the anchor-soil bounding surface. The approach was shown to reproduce adequately experimental tests on a sand, proving realistic stress distributions around the anchor. Nonlinear soil behavior influenced to a large extend relative interface motions. Michalowski (1989) applied an upper-bound limit analysis in 3D to slope stability analyses. Anchors were not specifically considered in this study, but the consideration of locally loaded conditions shed light on important modeling aspects. The manner how the slide mechanism becomes three- dimensional as the slope is locally loaded was demonstrated. This emphasizes the fact that anchors should produce field conditions that require 3D analysis approaches.

Jan 1, 2019