Search Documents

By Ting-Wei Wang, Yung-Wen Chen

Artificial ground freezing is commonly used globally during excavation of shield tunnels and for groundwater control. It is a special construction method for temporary ground improvement that involves introducing coolant into underground pipes to freeze water in the soil. The frozen soil is cemented together as a result to form a frozen wall, which provides high strength and low permeability. Once the thickness of the ice wall reaches design requirements, underground excavation can be conducted with the coolant removed afterward to return the soil to its original state. This technique is cost-effective in scenarios where complete groundwater cut-off and excavation support are required; where work is deep underground and faces difficult ground conditions and where access restrictions limit the use of other displacement-type ground improvement techniques. Due to the demand for shield tunnel construction for utilities in Taiwan, ground freezing has become an important soil stabilization method there. In this article, we will share two brine freezing case studies and an in situ liquid nitrogen experiment that was conducted to develop this technique.

Feb 1, 2022

By J. L. Liu

Long-term maintained load test on the bored pile group in unsaturated silty soil has been carried out. And the research on the time effects of bearing behavior of pile group has been done by the method of installing pressure cells and reinforcement stress gauges for measuring the soil reaction beneath the cap and the pile bottom as well as the shaft resistance. The test shows that, within a certain duration after loading, the soil reaction beneath the cap and the pile point resistance increase with time; but the shaft resistance decreases. The load distribution among the pile tops in the group tends to be even with time. The shaft resistance redistributes along the pile shaft with time, that is, getting less in the upper part, getting larger in the middle. The redistribution does not tend to stop till the distribution in both upper and middle part becomes to be uniform. The load-bearing conditions of soil beneath the cap of pile group and the variation in time effects with related factors also have been discussed.

Jan 1, 2010

By Marcus Daubner

This paper explains how BAUER Spezialtiefbau GmbH uses digital methods on projects - starting from work preparation to completion of works. More precisely, the advantages of BIM-based planning during work preparation and the automated and structured data management - both machine production data and the manually recorded quality-relevant reports - during execution phase are displayed. In this context, the benefit of the digital twin to optimize processes, to reduce defect costs, for a more effective reporting sys-tem, and the further usage of as-built information in the BIM or GIS process is described.

Sep 1, 2022

By Subhash B. Bhide

Deep foundations are affected by the presence of sulphates, chlorides, organic contents and water currents present in the soil. The sulphates in soil and ground water interfere first with setting of concrete. In long term, growing of sulphate crystals in concrete, crevices can spall the concrete. The chlorides mainly affect the steel. The organic content does not allow the concrete to set. It also reduces the compressive strength of concrete. The frequency and methods of sampling and testing for above corrosive elements are discussed. Presently available methods to avoid attack due to these corrosive elements are discussed. The stipulations by various codes are summarised. A method to assess the short term impact is elaborated with results of field studies. A tool developed to study the presence and effects of underground water currents on concrete is also discussed.

Jan 1, 1996

By Matthew D. Marks

The Sacramento Area Flood Control Agency initiated the Natomas Levee Improvement Program in 2006 which would bring the entire 42 mile Natomas Basin perimeter levee system into compliance with applicable Federal and State standards for levee protecting urban areas. The soil-bentonite slurry cutoff has been utilized as the primary construction method for addressing the under seepage deficiencies. To date, a combined total of over 4,500,000 square feet of slurry cutoff wall have been constructed utilizing excavation methods to a maximum depth of 75 feet and deep soil mixing methods to a depth of 90 feet. The construction of these cutoff walls has required the use of newly designed and custom built long boom and stick attachments for large hydraulic excavators and additional resource will be required to complete future phases. Key components of the NLIP program have included advancements in the development of soil-bentonite backfill mix designs, specified ranges on the soil backfill gradation to address concerns of long term consolidation of the backfill material, evaluation of the trench slurry filtrate loss with regard to cutoff wall acceptance, maintenance high slurry densities to provide greater trench stability, and continued development of backfill mixing procedures.

By Takeo Asanuma, Sachihiko Tokunaga, Hirofumi Taguchi, Yasuhiro Ootsuka, Yosuke Tanaka

The Cement Deep Mixing Method (CDM Method) is a ground improving method that has been used for mainly offshore sites to strengthen the soft ground below the sea bottom by injecting and adequately mixing cement slurry with soft soil into the ground to form a ground-improving column. In recent years, the CDM Method has increasingly been adopted for ground- improving work as part of liquefaction countermeasures and earthquake-resistant reinforcement in the shallow waters of river mouths and inland waters. In consequence of that, a pontoon-mounted CDM Method (CDM- FLOAT Method) has been developed for shallow waters, which is equipped with a land-type mixing machine combined with system management equipment and a tide level-based control function. This CDM-FLOAT Method can be deployed at work sites where the conventional offshore-use CDM barge cannot be employed. This report describes the CDM-FLOAT Method and the scope of applications together with construction work procedures, and a representative case of use of the CDM-FLOAT Method is introduced as an example of earthquake-resistant reinforcement of the existing embankment of a canal.

Jan 1, 2015

By Z. Q. Wang

The author is trying to clarify the existing problems in designing and laying out dynamic consolidation for soft ground improvement. Field testings and observations including vibrational parameters, pore pressures, stereoscopic photogrammetry etc. were run in order to trace the real behaviour of ground movement during tamping. It is believed that all the data got from the field work are rather informative and illustrative than that from theoretical modelling in the laboratory, thus some highlights relating effective thickness of compaction, maximum spacing between compaction points, number of blows for optimum tamping and seismic attenuation for environmental consideration are given.

Jan 1, 2010

By K. Oshima

In Japan, earthquakes are experienced frequently. Many buildings and structures in Japan are supported on pile foundations. For these pile foundations, the joint section between the piles and footing (hereinafter referred to as "Pile Head Joint"), where the load of the superstructure is transmitted to the ground through the piles, is important in both the design and construction of works particularly under seismic conditions. This paper discusses the state in which the force is transmitted to the Pile Head Joint, and introduces the basic construction of the Pile Head Joint, based on experimental investigation. Steel pipe piles

Jan 1, 2010

By Fawad S. Niazi

Analysis of deep foundations in terms of axial capacity has been a topic of great interest in the soil-structure interaction problems. Soil behavior is governed by a series of complex stress-strain changes that occur during pile installation and subsequent loading. Owing to the difficulties and uncertainties on the basis of the soil strength-deformation characteristics, one of the most frequently followed design practice is to refer to the formulae correlating directly the pile axial capacity components of unit base resistance (qb) and unit shaft resistance (fp) to the data collected from cone penetration test (CPT), i.e. to the tip stress (qc or more proper qt), sleeve friction (fs), and shoulder pore water pressure (u2). The elementary basis for such formulations has been the idea of considering cone penetrometer as a mini-pile foundation. This has resulted in plethora of correlative relationships in the past over 60 years. Such correlations, although empirical, have been worked out on the basis of load test results from both instrumented and un-instrumented full scale piles and are able to accommodate many important variables. A quick review of the evolution process and development of such design formulations is presented with a view to propose recommendations for future research directions, where the latest version of CPT i.e. seismic piezocone test (SCPTu) can be used to advance from capacitysingularity to the complete axial pile load–displacement (Q–w) response.

Jan 1, 2013

By F. Keith Jacobson

To be involved in the construction of a deep dredged caisson for a major bridge pier is one of the most rewarding and professionally challenging experiences one can have in the bridge construction business. That experience was doubled in the construction of the two deep dredged caissons for the Highway 82 Bridge over the Mississippi River near Greenville, Mississippi. The challenges and the construction risks associated with constructing these two dredged caisson pier foundations highlight the construction engineering innovation associated with major bridge pier construction. The 1,378-foot Main Span of the Highway 82 Bridge makes it the longest cable stayed bridge span over the inland rivers of the United States. The main piers for this bridge are supported on two dredged caissons measuring 80-feet by 122-feet in plan, founding 200-feet and 170-feet below the river surface. The challenges of constructing these caisson structures, sinking them through 70-feet of water to the river bottom and then excavating and further sinking them to the founding grade without exceeding the design tolerances, were enormous. The construction engineering opportunities for innovation included major breakwater structures to create a friendly environment in 11 fUsec currents, the first time use of Articulated Concrete Mattresses for river bottom scour control, unique air dome design to maximize the buoyancy of the caisson structure while floating, a caisson guide system to assure positive control and positioning of the caisson during the initial sinking phases. and a comprehensive sinking plan to assure maximum control and minimum risk. Many of the innovative solutions to the construction challenges on this bridge will be incorporated into future caisson construction projects on the lower Mississippi River.

May 11, 2007

By Makarand G. Khare

Though the phenomenon of dragload is known for many decades, there is a lack of clear guidelines to evaluate the amount of dragload. The development of dragload depends on relative movement between pile and surrounding soil which is a complex phenomenon and requires a detailed numerical analysis. Bitumen layer has been used in the past with varying degree of success in reducing the dragload but the reduction appears to depend on number of parameters. No procedure is available in literature to estimate the dragload when a slip layer is applied on pile surface. This paper investigates performance of two commercially available bituminous coats to reduce the negative skin friction on pile. Direct shear test apparatus was used to model the interface friction between soil and coated pile surface. The lower half of direct shear box was replaced with either a concrete block or a mild steel block representing pile surface. Two types of bituminous coats namely Shalikote and bitumen having penetration value of 30-40 were evaluated in this study. Shearing resistance of pile material-coat-soil is found to be influenced by normal stress, coat thickness, and rate of shear. Laboratory results are compared with published field data where coated and uncoated piles have been load tested.

Jan 1, 2006

By Lin Li

A reliability based analysis method for a drilled shaft stabilized slope system is presented in this paper. In the past effort, a deterministic method using the limiting equilibrium method of slices for determining the global factor of safety of a slope reinforced by a row of drilled shafts was developed using the soil arching concept. The drilled shaft stabilization mechanisms for the slope were treated as the drilled shaft induced soil arching, which reduces the driving forces on the down slope side of the drilled shaft. The effect of drilled shafts induced soil arching on the reduction of the driving stresses in the limiting equilibrium slope stability analysis was quantified by the load transfer factor through extensive finite element simulation studies. A semi-empirical equation was also developed for expressing the load transfer factor as a function of the soil properties, including strength parameters and unit weight as well as the slope geometry and soil profile, the location and spacing of the drilled shaft, and the dimension of the drilled shaft. However, due to the inherent uncertainties of the soil properties and the model error of the semi-empirical load transfer equation, a modification of the deterministic method into a probabilistic method is developed in this paper. The Monte Carlo statistical method is used to generate random variables for the soil strength parameters based on the prescribed probability characteristics, including mean, COV, and the probability distribution function. In addition, the modeling error of the load transfer factor is also treated as a random variable in the Monte Carlo simulation method, in which the mean, COV, and probability distribution function for the bias of the semi-empirical equation are used. The developed theories were coded into a computer program for analyzing complex slope geometry and slope profile conditions. Two examples are shown in the paper to illustrate the analysis results of the developed probability approach for determining the reliability of a drilled shaft stabilized slope system.

Jan 1, 2017

By Lin Li

A reliability based analysis method for a drilled shaft stabilized slope system is presented in this paper. In the past effort, a deterministic method using the limiting equilibrium method of slices for determining the global factor of safety of a slope reinforced by a row of drilled shafts was developed using the soil arching concept. The drilled shaft stabilization mechanisms for the slope were treated as the drilled shaft induced soil arching, which reduces the driving forces on the down slope side of the drilled shaft. The effect of drilled shafts induced soil arching on the reduction of the driving stresses in the limiting equilibrium slope stability analysis was quantified by the load transfer factor through extensive finite element simulation studies. A semi-empirical equation was also developed for expressing the load transfer factor as a function of the soil properties, including strength parameters and unit weight as well as the slope geometry and soil profile, the location and spacing of the drilled shaft, and the dimension of the drilled shaft. However, due to the inherent uncertainties of the soil properties and the model error of the semi-empirical load transfer equation, a modification of the deterministic method into a probabilistic method is developed in this paper. The Monte Carlo statistical method is used to generate random variables for the soil strength parameters based on the prescribed probability characteristics, including mean, COV, and the probability distribution function. In addition, the modeling error of the load transfer factor is also treated as a random variable in the Monte Carlo simulation method, in which the mean, COV, and probability distribution function for the bias of the semi-empirical equation are used. The developed theories were coded into a computer program for analyzing complex slope geometry and slope profile conditions. Two examples are shown in the paper to illustrate the analysis results of the developed probability approach for determining the reliability of a drilled shaft stabilized slope system.

By Emad Farouz, Ehab S. Shatnawi, Charles Winter

The increasing demand for small deformations and high-capacity drilled shafts without enlarging drilled-shaft diameters has motivated the development and increased use of a base grouting (BG) technique. This technique has been demonstrated to improve drilled-shaft axial capacity, especially for shafts tipped into loose cohesionless soils. To date, there are a couple of documented design methods for estimating the axial geotechnical resistance of base-grouted shafts. However, there is no or lack of research that addresses the lateral response of such shafts. A base-grouted drilled shaft test program was carried out during the design phase of the Wisconsin I-94 Zoo Interchange reconstruction project. The test program included installing and testing one base-grouted shaft and one ungrouted shaft under both lateral and axial loading. Based on test results, it was concluded that the lateral behavior of the BG drilled shaft is significantly stiffer than conventional drilled shaft . Hypothetical method was developed to account for potential increased, however, the method should be verified with more lateral load test.

Caissons hand dug to a depth of about 100 feet were used to underpin three important structures at an industrial site in the State of Utah. The caisson shafts extended through 30 to 40 feet of coarse, granular soils and 25 to 60 feet of sands and clays to bear on a very dense, coarse gravel and cobble stratum near the water table. The shafts were belled to 12 feet square at their bearing elevation. Bearing pressures of 20 ksf were assigned. The shafts were lagged with timber. The use of hand-dug caissons allowed continuous operation of the facility during underpinning. Settlements after underpinning have been minor and well within the estimated magnitudes. Instrumentation was placed in two of the caissons with varying degrees of success.

Jan 1, 2010

By Jochen Maurer, Dr. Christian Hoyme, Dr. Hans Regler

Currently, it is very difficult to obtain qualitative and quantitative information about the status and production process of a construction site. As a rule, companies depend on reports from on-site experts. There is no end-to-end digitalization due to the mobility of equipment and ever-changing locations. Equipment from different manufacturers, especially in special foundation engineering, is highly specialized. Any data collected by this equipment is recorded in proprietary formats and made available on the manufacturers' platforms. This exacerbates the situation, making simple analysis of performance indicators impossible. Most functions such as construction diaries, equipment utilization analyses, etc. are implemented only as standalone solutions. This does not allow for prompt visualization and intervention in critical process sequences because the construction site process is usually managed using a cost-based method. Furthermore, special foundation engineering requires a high level of expertise in an extremely wide range of construction processes. In this article, the results from a set of non-proprietary performance analysis tools are presented using numerous practical examples. Once a construction element is completed, the equipment data is immediately transferred to the platform using the latest cloud technology. Because the data is normalized, construction progress can be documented immediately, even for mixed equipment fleets. Bottlenecks can be immediately detected by visualizing the current performance of the production process, which is broken down into individual steps. Modern analyses of this equipment data improve quality, thereby providing better information about current performance. These sets of tools are essential for changing from the current monetary or cost-based method of process management to time- and bottleneck-oriented management. This makes it much easier to identify the critical path during projects. The article shows that processes can be documented and managed.

By Raffaella Granta

Mosul Dam is an earth fill dam located on the Tigris River, approximately 40 km (25 mi) northwest of Mosul, Iraq. The construction of the dam was completed in 1984. It is one of the largest multipurpose dams in the Middle East, and the largest dam in Iraq. The dam provides flood control, irrigation, power generation and water supply. At 113 m (371 ft) high and 3.65 km (2.3 mi) long, the reservoir has a storage capacity of 11.1 billion m3 (392 billion ft3) of water. The main hydroelectric power station has four turbines for an installed capacity of 750 MW. The discharge system includes two bottom-outlet tunnels of 10 m (33 ft) diameter, a five-gate service spillway and an emergency fuse plug spillway.

Oct 1, 2022

By Jeffery L. Ottesen

Early construction delays can jeopardize timely completion of subsequent work. As an early construction activity, and due to many unforeseen issues, deep foundation work inherently bears great potential for impacting the critical path of a planned construction schedule. This article describes two construction projects where delays related to deep foundation work forced the Contractor to consider various schedule recovery alternatives to mitigate those delays. Specifically, deep foundations on Vancouver BC's Millennium SkyTrain light rail extension and on a Mill Facility in the United States are discussed. This article cites examples of permitting delays, alleged design changes, differing subsurface conditions and changed construction methodology, the effect each problem had on the project, the mitigation means implemented by the Contractor to minimize adverse impacts of the problem, and Lessons Learned for each scenario.

Jan 1, 2002

By T. Matsui

Many existing bridge abutments on the soft ground laterally move and their many damage examples have been reported. An essential cause for the troubles of the lateral movements may be the lack of examinations for the lateral earth pressure acting on its foundation piles. In the present paper, actual movement condition of existing bridge abutments is first summarized, and then the author establishes a practical and systematical design method for bridge abutment foundation piles, including the examination for the passive pile.

Jan 1, 2010

By Peter Arz

In the port of Hamburg a 650 m long quay wall was completed in mid-1985. The watertight wall consists of loadbearing steel buttress piles PSP 1012 which are up to 28 m long and infill interlocking sheet piles PZ 612. The construction method used for this quay wall, which included the simultaneous implementation of ground improvement measures, is the subject of this lecture. Originally, as is common practice, driving of the sheet piles had been envisaged. The composition of the subsoil, which consists of fill, clay, sand and boulder clay, is typical of the Hamburg region. In the upper layers (down to a depth of approx. 15 m), the subsoil is interspersed with debris from ancient civilisations but also dating from the war and post-war period (bomb craters filled with debris and demolition material).

Jan 1, 1987