Search Documents

By George Piscsalko

"Quality control of drilled shafts and CFA piles is greatly dependent upon the practices of the site personnel. In many applications it is difficult or not possible to fully inspect the shaft prior to concreting, such as when the shaft is drilled under slurry. CFA piles are cast with no ability to inspect the shaft prior to concreting. There are numerous methods currently available to assess the integrity of drilled shafts and CFA piles. This paper will compare evaluations by three existing non-destructive test (NDT) methods with a new method of Thermal Integrity Profiling for assessing integrity in drilled shafts and CFA piles. This Thermal Integrity Profiling method determines the integrity over 100% of the shaft cross section, both inside and outside the reinforcing cage, by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements are made typically only 12 to 48 hours after concrete placement, thus accelerating the construction process. Thermal Integrity Profiling will be described in detail and the Thermal Integrity Profile (TIP) results from several shafts with purpose built defects will be discussed along with several case histories from drilled shafts and CFA piles where Thermal Integrity Profiling was used. The case histories will compare TIP with various other NDT tests utilized on these particular piles including comparisons with Low Strain Integrity Testing and Cross Hole Sonic Logging. Test results for the various methods will be discussed and the excavation of the upper portion of one drilled shaft will be shown and discussed. IntroductionDrilled shafts can be a desirable foundation element in many applications due to the large axial and lateral capacities which are attainable for very large drilled shafts. Drilled shafts can be cast in a dry hole which allows for inspection of the hole prior to casting, but the casting process is very difficult to nearly impossible to inspect with any accuracy. Drilled shafts are frequently cast under slurry as a means to stabilize the surrounding soils during the construction process. When casting a drilled shaft under slurry, it is very difficult to accurately inspect the hole prior to casting and it is equally difficult to inspect the shaft during the casting process. CFA piles are another popular choice for their relative ease and speed of installation. The trend has been larger CFA piles carrying greater loads, which makes quality control critical for these piles. Many of the above mentioned processes are blind to inspection and therefore the chances increase for having defects present in the completed elements."

Jan 1, 2014

By Thai Nguyen Ph. D

Dynamic Load Test (DLT) on driven piles has been performed routinely all over the world. In several recent projects, even 100% testing has become a norm where every single pile is dynamically load tested. In these cases, most piles are of uniform sections, making the field analysis (CASE method) straight forward. The CASE method, which has been used for the last 50 years, however, is only applicable to uniform piles to monitor pile driving stresses as well as pile capacities. Signal matching analysis can handle different configurations. However, the analysis used to require user inputs (i.e., non-automatic). Manual signal matching analysis, which can solve non-uniform solutions, traditionally takes hour(s) to complete for one blow. As such, the real-time pile driving stresses and resistances had traditionally been relying upon the CASE method, using typical range of CASE damping (JC). Until 2021, due to the lack of a rigorous instant signal matching analysis for non-uniform piles, no tool was available to help engineers evaluate non-uniform piles in real-time. An inexperienced field engineer may overlook this shortcoming when evaluating peak driving stresses. Furthermore, ultimate bearing resistances for non-uniform piles may require further evaluation to account for the non-uniformity of piles if relying on the CASE method. This paper highlights recent advances in instant Signal Matching Analysis on non-uniform piles, allowing field engineers to monitor stresses and resistances of non-uniform piles during driving.

Oct 1, 2022

By Steve Davidow, Ashely E. Evans, Peter M. Kandaris

"Annually thousands of deep foundations are constructed across North America supporting high voltage transmission line structures. However, a recent state of the practice survey by the Deep Foundation Institutes’ Electric Power Systems Foundation Working Group discovered that the electric power utility industry lacks consistent foundation design guidelines. The survey identified a wide variability in design assumptions, a minimal understanding of risk based analysis, and a need to standardize design methodologies. This paper summarizes the state of practice in electric system foundation design and proposes a framework for risk-based foundation design by accounting for uncertainty from both loads and resistances. Loads derived from electric system codes do not necessarily provide a compatible level of reliability for the design of foundations, as they are a mixture of probabilistic and deterministic values. Load uncertainty is derived from variability in weather conditions, structural models and material properties, typically accounted for by code derived overload factors. Resistance uncertainty arises from variability in natural soil properties, resistance models, subsurface construction techniques, material sampling methods, and limited observations. A consistent methodology is offered relating nominal resistance capacity (strength) to structure loads and service state criteria. Discussion also includes the need for risk-based assessments to account for non-structure load influences (fluvial loads, scour ground loss, liquefaction, etc.).INTRODUCTIONNearly 40 years ago the Electric Power Research Institute (EPRI) embarked on a major research effort to optimize reliability and economics of transmission line foundation design. Strategies focused on improvements in design models, site characterization, exploration strategies and testing to reduce uncertainty and variance in analysis. Transmission line engineers realized that safety and reliability advancements in design based on probabilistic approaches, with a focus on the unique nature of transmission line, could better control risk and cost.Some transmission line professionals took full advantage of these advancements, particularly where research led to improved software and models. Yet, even after two decades of extensive research, by 1995 the industry still had made little progress in changing design habits. The majority of designers were still characterizing sites via deterministic methods, using loads that may or may not relate to a consistent probability of occurrence, and applying a traditional global factor of safety approach (Phoon, et al. 1995). The following two decades have seen even greater developments in software and reliability-based analysis methods, but old habits seem to die hard as recent surveys show less than half of design professional quantitatively assess risk in their design process."

Jan 1, 2017

By Carlos Lam, Joram M. Amir, Erez I. Amir

"Abstract The modulus of elasticity of pile material (E) is an important parameter for the interpretation of both static and dynamic loading tests on piles. This value is commonly assumed to be constant with depth though it may not be true for deep bored piles due to the chosen casting method and/or selfweight consolidation. To provide evidence to support this proposition, the results of compressive strength tests on core samples taken from four different studies have been presented. The results show a marked increase in the strength and stiffness values with depth. The results of crosshole ultrasonic tests conducted at another site also confirm the same pattern. It is therefore recommended that before load testing a pile the distribution of the E values along the pile axis should be investigated. This will ensure the use of a realistic elastic modulus value and hence the correct interpretation of thedistribution between the shaft and end resistances.IntroductionThe modulus of elasticity of pile material (E) is an important parameter for the interpretation of both static and dynamic load tests on piles. Multiplying E by the strain measured by either strain gauges (e.g. ASTM D4945) or tell-tales (e.g. Geffen and Amir, 1971) gives the stresses acting at a given pile section. Typically, in the absence of better information, the value of E is derived from laboratory tests on concrete cubes or cylinder specimens taken on site and is assumed to be constant along the pile. While this may be correct for pre-fabricated concrete piles that are cast in horizontal molds, it may not be true for cast-in-place piles that are produced in the vertical position.There are at least two factors that may contribute to the change in concrete properties with depth in a bored pile. First, the casting methods may be by free fall in dry holes (e.g. Kiefer and Baker, 1994) or by using a tremie tube if support fluids are used. In the former case, the earlier batches reach the bottom of the pile bore at a higher velocity and are thus compacted under higher energy. Second, regardless of the casting method, the fresh concrete in the pile bore will always consolidate at least partially under its own self weight. The materials in the lower parts of the pile will therefore experience a higher consolidating pressure. This can reduce the pore volume and the water content in the wet concrete, thus changing the properties of the hardened concrete. Recent research by Justs et al. (2011) has shown that even a relatively small pressure can have a significant positive effect on concrete properties such as compressive strength and stiffness. However, the possible change of concrete properties with depth is commonly ignored by foundation engineers in the current design practice."

Jan 1, 2014

By Christian Hoyme, Jochen Maurer

Most of the current foundation projects are suffering from disconnected information silos. In the first silo there is the planning of the project with corresponding data, presented by paper or digital drawings. Here will Building Information Modeling (BIM) be one of the trends for the future. We will see more and more projects leaving the “old way” of 2D drawings and moving into 3D planning including metadata of the foundations. But even with a perfect BIM model of a jobsite, we are not at final end of digitalization. While execution of the project at the jobsite, a second data silo is evolving. Data collected directly from construction equipment and manual measurements is currently undervalued in most projects. Paper is passed to the equipment operator and major data from measurements on site are noted on paper and digitized afterwards. Automatically collected data is not be used to create site progress reports or similar report. So, the real “data” just flows around without connection to any other data already existing in projects. And then the third silo arises: The documentation of the project. Data collected on paper es reentered to create some basic documentation of the work handed over to the client. Spreadsheet software is still the “tool-to-be-used” to create at least some documentation. Finally, the documentation is not connected to the data created while planning and not connected to the automatically collected data from the jobsite. A connected jobsite in the foundation industry must link these information silos and have to create a full data-workflow from the design through the execution to the as-built documentation. INTRODUCTION Building information modelling (BIM) is currently the most popular term of construction business in Germany and probably all over the world. But as often there are many different definitions out there and everyone has his own definition or at least understanding what BIM is about. But for sure it is the most relevant for the construction industry in the near future. Most popular is the digital twin for the upper structure of a building. In most cases the BIM models just shows the building itself, but there is more to be implemented. For example: projects where a special foundation is needed, BIM should include also the foundation elements with meta data. There are several advantages. Not only the clash detection of anchors, but also the possibilities to check the interaction with neighbor constructions, power lines and so on are a use case. For sure most of the special foundation elements are not relevant for the whole lifecycle of a building. But during construction and later the demolition the information about the hidden elements is important and gives a benefit to all stakeholders. In the future there will be not the question: “What is already in the ground?”. The risk for following construction projects on the same ground will be minimized.

Jan 1, 2019

By Cristhian C. Mendoza, Renato da Cunha, Bernardo Caicedo, Max Barbosa

"Abstract This paper shows that a raft alone is not sufficiently appropriate to address the uncertainty of underlying soil variability; therefore, a piled raft system is a better option for mitigating such uncertainty. To study the variability of soil, the behavior of the Piled-Raft Foundation was analyzed with a type of self-drilling micropiles: the ""Alluvial Anker"" (common name for this pile type in Brasilia city). These micropiles have been used in the city and have the advantage that the drill pipe also serves as reinforcement. The studied parameters belong to an elastoplastic constitutive model for strain-stress analysis of soil; variability of these parameters can be intrinsic and/or epistemic. Simulations were performed for a hypothetical Piled-Raft Foundation subjected to vertical loading using the random finite element method. The average parameters of the constitutive model were obtained through laboratory tests. The simulations of the load test were compared with results of a real scale experimental test conducted exclusively for this work in the field. It is analyzed the relative importance of the variability of some geomechanical parameters and their variation with depth is considered. In addition, it is discussed a comparison between the uncertainty of the geomechanical parameters and the uncertainty of the results of the vertical loading test. Finally, this paper shows that a decrease of the safety factor may occur when taking into account the variability of the parameters.IntroductionBrasilia is located in a highly weathered residual tropical soil (lateritic & latossol on pedogenetic concepts). This soil presents high content of alumina and iron due to the lixiviation process of the upper layers. As a consequence, the cemented structure is highly unstable and it can generate strong changes of volume (i.e. collapse) due to changes in both moisture and state of stresses. Therefore, a greater understanding of the construction of Piled-Raft Foundation systems on this particular soil conditions is needed – especially because it covers more than 80% of the surface area of the Brazilian Federal District.Thereafter, this work investigates the influence of the variability of the soil parameters over the uncertainty of the Piled-Raft Foundation design. The studied parameters belong to an elastoplastic constitutive model for strain-stress analysis of soils. The simulations were performed for two hypothetical Piled-Raft Foundations subjected to vertical loading by using the stochastic finite element method. The results were compared to real load tests in Piled-Rafts with “Alluvial Anker” pile types."

Jan 1, 2014

By Tracy Brettmann

A new method for estimating ground vibrations caused by pile driving was developed as a result of a vibration monitoring program performed for a large pile driving project. The method is accurate, rational and theoretically based starting with energy actually transmitted to the pile (not the rated or operating hammer energy). This energy is then assumed to be transmitted to the soil in the form of surface waves that attenuate from both geometric and material damping. The main input parameters for this method include the energy transmitted to the pile and the dynamic properties of the soil (wave velocity, material damping, and unit weight). In this study we concurrently measured both: (1) pile driving of 14-in.-square, 65-ft-long precast concrete piles with a Pile Driving Analyzer?, and (2) vibration levels at various distances away from the piles during driving. A geotechnical study for the site was also performed that included measurement of the dynamic soil properties using both crosshole and seismic cone testing. This paper presents the data obtained from the study and compares the results to the values estimated using this new method. Vibrations from pile driving is a serious matter that impacts virtually every pile driving project. It is important that accurate methods for estimating ground vibrations be available to engineers and contractors.

Jan 1, 1999

By Samuel J. Kosa

The Monotube is a uniformly tapered high-strength steel shell pile manufactured for friction pile applications. The Monotube pile was developed in the early 1920's in Canton, Ohio. Its first commercial installation was an Ohio railroad trestle in 1926. The Monotube has been manufactured in the same Canton plant since its inception. The Monotube is produced in four diameters, 12, 14, 16 and 18 inches, with U. S. Standard Gage wall thicknesses of 9, 7, 5 and 3. The uniformly tapered Monotube section can be manufactured in one of three rates of taper.

Jan 1, 1993

By Randy R. Williams, Brian W. Wilson, George M. Filz, Marina S. W. Li, Donald A. Bruce

"In-situ wet grab sampling and post-installation coring of soil-cement structures are typically carried out for Quality Control (QC) and Quality Assurance (QA) of deep mixing (DM) schemes. Wet grab sampling and testing is used to provide data to indicate that performance requirements are being met during production, in advance of coring, which typically occurs at 28 days or later, following installation. While unconfined compressive strength (UCS) tests from wet grab samples provide good production indicators, industry practice often requires that acceptance criteria of soil-cement structures be based on UCS results from representative core samples.This paper outlines the approach adopted for field sampling and QA/QC testing carried out in highly variable subsurface conditions at a site located in northern British Columbia (BC), focusing on postinstallation soil-cement coring and strength testing for an extensive deep mixing scheme. A discussion on suitable methods of coring soil-cement structures and appropriate selection of samples for testing that are representative of the in-situ soil-cement structures is provided. This paper also discusses the selection strategy adopted for verification of strength and modulus parameters used for design, providing spatial and time coverage, as well as the acceptance criteria implemented, and provides comparisons with published industry recommendations.BACKGROUNDAn extensive deep mixing ground improvement scheme was completed for the development of a Liquefied Natural Gas (LNG) Facility to be located in Bish Cove, BC, Canada. The deep mixing scheme was implemented to treat very weak native deposits in-situ to support two mechanically stabilized earth (MSE) walls up to 20 m (66 ft) high, and their associated bulk earthworks. Within the DM area, the subsurface conditions were highly variable, ranging from deep (up to 21 m (69 ft) thick) deposits of very soft to soft clayey silt to silty clay, overlying layers of dense to very dense gravelly sand to sand and gravel, to compact deposits of silty sand (up to 15 m (49 ft) thick), overlying dense sand and gravel. Bedrock was encountered beneath the granular deposits and generally comprised granodiorite with occasional andesite dykes."

Jan 1, 2015

By Frank Rausche

Since the early 1980s, when the Road Construction Authority of Victoria authorized the dynamic proof testing of roughly 100 drilled shafts of 1.5 m diameter and typically 60 m length in Melbourne Australia, dynamic load testing has been applied worldwide for quality control of drilled shafts. Today, test capacities of 4000 tons or more are not unusual. On numerous occasions the authors have been involved in similar tests in the United States and test engineers from other countries have reported on experiences in many different countries. Without doubt, generating high test loads is most economically accomplished by dynamic load testing and this method is particularly well suited for testing piles founded in rock because of the rocks low energy dissipation. However, deep foundation professionals have on occasion expressed reservations about subjecting a drilled shaft to impact loadings fearing, for example, a degradation of the shaft ? rock interface properties or potential error sources due to uncertain concrete properties or shaft geometry. This paper will present numerous case studies, demonstrating the performance of rock socketed drilled shafts under dynamic loads. It will discuss the mechanics of the dynamic tests and the method of data interpretation, addressing the concerns stated above and investigating the limitations of the test method. The paper will formulate a set of recommendations for the design and execution of these tests.

Jan 1, 2006

By Rudolph P. Frizzi

Quality control is essential for augered cast-in-place (ACIP) piles (also known as continuous flight auger (CFA) piles outside the United States) and drilled displacement (DD) piles since the pile is constructed below the ground surface out of the direct sight of the personnel constructing and inspecting the pile. ACIP piles are being successfully constructed to support high-rise structures, hospitals, arenas and stadiums, mass transit systems, and power and industrial facilities. The use of DD pile technology is also gaining ground in the United States, typically utilizing proprietary systems such as Omega (currently utilized by Richard Goettle Inc., and LG Barcus and Sons, Inc.), Berkel, and DeWal (currently utilized by Morris-Shea). Different types of ACIP/DD pile installation equipment are shown in Figures 1 and 2. ACIP piles are installed into granular and cohesive soils, and soft rock to lengths currently approaching 130 ft (39.5 m), with diameters up to 24 to 36 inches (610 to 915 mm), and sustaining design loads approaching 900 kips (4000 kN). Current DD pile installation equipment in the United States is capable of installing up to 79-ft-long (24 m) piles with diameters ranging from 12 to 18 inches (305 mm to 460 mm).

Jan 1, 2003

By Grant R. J. Bearss

Due to environmental concerns in urban construction, many typically simple projects become very complex or feasibly impossible. The introduction of relatively new concepts has redefined "impossible", again simplifying these projects and making them "possible". Case Study One covers the use of Pressed-in Tubular Piles on portions of the Long Island Expressway in Queens, New York. Innovations in the design, material and installation method solved many typically inherent problems on projects of this type and resulted in cantilevered walls that supported a 35ft (10.668m) excavation. Design predictions and actual measured deflections of this wall were within millimeters. Case Study Two covers the use of Pressed-in Tubular Piles on portions of the Hodogaya Bypass in Yokohama, Japan. Innovations in equipment development allowed for a cantilevered retaining wall to be constructed without affecting the adjacent right-of-way, dramatic reduction of the overall construction duration and installation of tubular piles in soils with SPT N values greater than 160.

Jan 1, 2002

By C. T. Christensen

The paper gives an outline of the design, installation and performance of a series of mooring and berthing dolphins for a major ferry berth outside the port of Elsinore, Denmark. The Dolphins are large cylindrical bottle shaped and open ended steel piles vibrated into the sandy seabed. They are subsequently equipped with prefabricated fender units. Vehicle access to the ferry is via a fixed ramp and a semi-submerged linkspan. Supplementary passenger access is via a covered gangway steel bridge from an existing gangway facility to a midship door in the ferry«

Jan 1, 1989

By Amy B. Cerato

The application of this study is to use helical anchors as a foundation system for small wind tower (1 ? 10 kW) guyed cables. Helical anchors are currently used to anchor guyed cables of telecommunication and electric towers. However, the increased dynamic vibrations a wind turbine adds to the tower and foundation system under working loads, as well as extreme environmental conditions (e.g., straight line winds, ice load or sudden furling shocks), require additional knowledge about the behavior of helical anchors. These field conditions were simulated in this study by instrumenting a working tower with load cells and 3-axis accelerometers to gather data on wind speed and tower response. These tower responses were then transmitted to the helical anchors through an extensive, large-scale testing program that included monitoring the performance of the helical anchor foundation under dynamic loads, subject to natural variations in both wind regimes, precipitation (water level) and variations in helical anchor geometry. This paper specifically discusses the effects of helical anchor geometry on helical anchor performance under long-term dynamic loads.

Jan 1, 2008

By B. B. Broms

A method for calculating the bending moment induced in misaligned or bent piles is described, The maximum bending moment varies with the angular rotation between the pile segments, the coefficient of horizontal subgrade reaction of the soil and the flexural rigidity of the piles. A case history involving damages to misaligned 365 x 365 mm square precast concrete piles is described.

Jan 1, 2010

By Michael W. Neill, O&apos

Drilling slurry has become an effective aid to the construction of drilled shafts in caving and/or waterbearing soils. Historically, drilling slurry made of bentonitic clay and water was first used in the US in water well drilling as early as 1889. In coastal Texas drilled shaft contractors began using slurry, often made of on-site clay mixed with potable water, in the years following World War II, on a relatively routine basis. This type of slurry was used to "process" boreholes, in which the borehole was drilled "in the dry" until water or unstable soil was encountered, after which water and on-site clay were introduced into the borehole and mixed in place with the auger or other drilling tool. Drilling then continued under a slurry consisting of the uncontrolled mixture of clay and water until the excavation had reached a relatively impermeable and cohesive material. At this point, a steel casing was dropped into the hole and sealed into the lower stratum of impermeable geomaterial (soil or rock). The slurry inside the casing was bailed or pumped out, drilling continued to plan depth in the dry, a reinforcing cage was set in the partially cased borehole, concrete was placed and the casing was withdrawn. Some soil-slurry was undoubtedly trapped between the casing and the borehole wall, but the quality of that slurry was usually of no concern, because engineers of the period usually viewed drilled shafts as nothing more than deeply buried footings. Any unejected slurry would only serve to lower side shearing resistance, not yet considered in design, but would have no effect on end bearing. In the 1960 's the effectiveness of soil-slurry came into question because it was often ineffective in maintaining borehole stability at marginal drilling sites and because the economy of using shaft resistance, in addition to end

Jan 1, 1991

By M. Melih Demirkan, Jared Deible, Michael Rosenmeier, Mazen Elias Adib, Juan J. Gutierrez, Raghav Ramanathan

Dewatering and groundwater control is required frequently for construction projects and needs to be accounted for and dealt with care during design and construction to complete the project successfully. Dewatering can cause changes in porewater pressure, which changes the effective vertical stress in a soil mass. Dewatering can also cause changes in groundwater chemistry which in turn can cause changes in porewater pressure and also dissolution of soluble minerals in the soil and rock. The Guideline developed in this study addresses the engineering issues, approaches to lessen the potential risks associated with construction dewatering, and presents dewatering practices to support dewatering applications regulated by the Municipality of Abu Dhabi City (ADM) in the United Arab Emirates (UAE). The subsurface condition within the city presents significant geotechnical problems due to presence of shallow subsurface cavities and soluble minerals in the soil and rock. Therefore it is critical to develop standards for dewatering practices to provide information for local dewatering engineers and contractors with special emphasis to control and to eliminate the subsidence/collapse problems related to dewatering projects within the Abu Dhabi city. The ADM is also responsible for approval of permit applications for projects that involve dewatering. In order to minimize the risk related to subsidence/collapse problems due to dewatering, construction companies and dewatering contractors need to be informed about possible mitigative measures that can be employed to reduce risks. The guidelines were developed as part of this study based on detailed analysis of the local subsurface conditions. A set of rules and regulations are developed for geotechnical and hydrogeological investigations, dewatering design and monitoring criteria depending on the hazard zones, proximity of excavation to critical structures, excavation depth. The Guidelines include examples of permit application packages for three types of dewatering projects; one involving shallow dewatering, one involving intermediate depth dewatering, and one involving deep dewatering. These Guidelines are considered as living document and will be updated as required, as additional information is collected and additional local experience is gained.

Jan 1, 2016

By Satyajit Vaidya, Rudolph Frizzi, Luis Berroteran

This paper presents design and construction challenges associated with a high-capacity rock-socketed drilled pile foundation system for a 60-story building recently constructed in an urban environment. The site is in very close proximity to surrounding 1-to-6-story buildings and a commuter rail subway tunnel structure. High compression, uplift, and lateral loads imposed by the tall, slender tower constructed over a relatively small site footprint posed a significant design challenge due to the close proximity of the subway tunnel and other structures. Construction challenges included those associated with advancing the drilled pile casings through overburden materials using internal flush method mandated by the Transit Agency, advancing the casings through very dense glacial till materials encountered above top of rock, and drilling rock sockets in variable rock conditions. This paper provides a brief overview of the site and subsurface conditions, and discusses the resulting design and construction challenges for the drilled pile foundation system and how they were addressed. SITE AND SUBSURFACE CONDITIONS The 8,350-square-foot site is located in a busy neighborhood in downtown New York City (NYC). Buildings neighboring the site are supported on shallow foundations, and their basements extend about 15 feet below the sidewalk level. A NYC-Landmarked building is located within a NYC Department of Buildings (DOB)-designated 90-foot influence limit from the Project site. NYC Transit Authority (NYCTA) subway tunnel and station structures are located in close proximity to the Project site. The subway tunnel structure extends about 50 to 55 feet below the sidewalk level. Although the upper portion of the tunnel structure is about 13.5 feet away from the site property line, the lower portion is only about 1 foot away from the property line. A site location plan is presented as Fig. 1. Geotechnical borings revealed subsurface conditions generally consisting of successive strata of surficial fill, sandy and silty soils, and glacial till (predominantly consisting of cobbles and boulders) overlying mica schist bedrock. A generalized subsurface profile is presented in Fig. 2. The surficial fill stratum was about 10 to 23 feet thick, and generally consisted of loose to medium dense sandy soils with varying proportions of silt, gravel, and miscellaneous debris such as brick. The underlying sandy and silty soil stratum was about 60 to 79 feet thick and generally consisted of loose to medium dense inter-bedded layers of fine to coarse sand, silty fine sand, and silt. The underlying glacial till stratum was about 26 to 70 feet thick and generally consisted of cobbles and boulders embedded in a very dense soil matrix. Top of bedrock was encountered in the borings about 110 to 150 feet below sidewalk level. Groundwater level was measured at about 30 feet below sidewalk level.

Jan 1, 2018

By Leonardo Massone

The p-y method is one of the most popular methods in pile design and has been calibrated for various boundary conditions using numerical and experimental studies during recent years. Most studies on reinforced concrete (RC) piles have included the impact of flexural nonlinearity, (e.g. nonlinear moment?curvature relations) but not considered associated pile shear deformations when deriving p-y curves from field data. Common p-y curves may be better applicable for piles with flexure dominated failures (e.g. piles with free- head boundary conditions). For piles with fixed head boundaries (i.e. rotation restrained piles) shear deformations could be of significant influence. To study this problem, a coupled shear flexure interaction model for axial-bending-shear behavior coded in OpenSees was applied to a 0.61 m (2 ft) diameter flagpole and a 0.61m (2 ft) diameter fixed head pile specimen to investigate the possible influence of shear deformations to the overall pile responses. The surrounding soil was represented by p-y curves derived from prior large scale testing on piles with similar boundary conditions. Analysis results show that for flagpole piles, shear forces and shear deformations were insignificant. Considerable contributions of pile shear displacements and forces were observed for the fixed head pile, with shear displacements contributing up to 40% of the total pile displacement. Results suggest that nonlinear shear deformations for reinforced concrete piles should be considered for fixed-head or similar conditions, and that currently used p-y curves may underestimate the actual lateral pile displacement and possibly lead to unsafe design for the particular boundary condition.

Jan 1, 2012

By Zhang Baoshan

In this paper, the forced features and dynamic behaviors of stone-column composite foundation are concisely related. The characteristics of Rayleigh wave method is summarised. This method is proposed in which, the stress ratio of the stone-column to the surrounding soil and the bear­ing capacity of the composite foundation are determined. Through the engineering cases, it is shown that, checking and evaluating the composite foundation in this method, is feasible, with high speed and low cost.

Jan 1, 1991