Search Documents

By Jesse R. Jacobson

A large casino complex in Cherokee, North Carolina recently underwent a $633 million expansion that involved substantial foundation challenges. The site is located in a valley on the southern edge of the Great Smoky Mountains National Park, where subsurface conditions typically consist of varying thicknesses of fill overlying alluvium, residuum, partially weathered rock and rock. The fill and alluvium contain cobbles and boulders as large as several feet in diameter. The residuum and partially weathered rock are very thick in some areas, and the depth at which consistently high quality rock is encountered is highly variable. To reduce the foundation costs for the expansion, continuous flight auger (CFA) piles were proposed in lieu of micropiles. CFA piles are not generally used in this geologic environment and concerns regarding their selection included: (1) an uncertainty that CFA piles could be successfully constructed given the difficult conditions and (2) a lack of regional data regarding unit resistance values and load transfer characteristics. To address these concerns, a design-phase test program was undertaken to evaluate pile constructability, develop an understanding of the load transfer behavior, and establish the required pile lengths. The program included soil test borings, shear wave velocity measurements, timed auger probes, instrumented pile load tests and observation of exhumed piles. It was demonstrated that CFA piles could be advanced through the fill, cobble/boulder-laden alluvium, residuum and into the partially weathered rock, albeit with some limitations. Under axial loading, the pile response was very stiff and relatively high unit resistance values were measured. Pile instrumentation allowed for the evaluation and use of design pile lengths shorter than that tested, and the overall reduction in pile lengths yielded a 40 percent reduction in foundation cost. In general, CFA piles were determined to be a suitable, economical foundation alternative.

Jan 1, 2011

By N. Shariatmadari

In recent years, determining bearing capacity of piles from in-situ testing data as a complement of static and dynamic analysis has been used by geotechnical engineers. In this paper, different approaches for estimating base bearing capacity of piles from SPT data has been compared and evaluated. A new method for pile base bearing capacity in sand is proposed using SPT records. Data averaging, failure zone extension, and plunging failure of piles have been addressed in the proposed approach. A data bank comprising 10 full scale static load tests on instrumented piles and 26 dynamic tests, analyzed with signal matching technique by CAPWAP software, was used for validation. The SPT data that was performed close to pile locations is also included in the data base. Comparison of current methods by error investigation with Log-Normal approach demonstrates that the proposed method predicts pile base capacity with more accuracy and less scatter in comparison to other methods.

Jan 1, 2006

By Mandy Korff

Walls consisting of CFA-piles are often used for vertical cut offs for building pits. Several methods of installation and geometry may be used and sizes, depths and strengths of walls necessary vary widely. Based on experience with secant CFA-pile walls in The Netherlands, requirements for this type of wall can be set with a risk management view to it. This paper describes those requirements, based on specific local conditions.

Jan 1, 2006

By Timothy D. Stark

Jet grouting has increasingly become one of the ground improvement technologies used to address seepage concerns and to provide strength improvement of soils. The technique of jet grouting uses high pressure/velocity jet fluids to erode the existing soil and then to mix the cuttings with cement slurry to form soilcrete. Excess slurry or spoil is ejected to the surface. If the native soil is not completely mixed with slurry, the resulting columns will have soil inclusions which can reduce the strength of the column and/or increase the permeability of the column. A jet grout test program at Tuttle Creek Dam shows that the completed large diameter columns contain perhaps 40 to 50% or more of native soil that was not broken up and mixed during the jet grout process. The test program included excavation of full-scale columns to a depth of 35 ft (10.7 m) for visual inspection and testing. Additionally, six of the columns were cut or sectioned to investigate the interior of the columns. The observed inclusions include significant amounts of both fine grained (silts and clays) and coarse grained (fine sands and sands) soils. Evidence suggests at least two explanations: (1) fine grained soils can be difficult to erode and break up into small enough particles that can be ejected to the surface, especially if at low natural water content, and (2) when large diameter columns are being excavated, the excavated roof of the cylindrical cavity may be unstable and may collapse. With this roof instability large slabs of material can break off, fall into the slurry and escape the cutting and mixing action of the rotating jets. This paper describes the Tuttle Creek Dam test program, inclusions observed in the completed columns, and suggests potential causes of the inclusions.

Jan 1, 2009

By Paul M. Wiltcher

This paper discusses how benefits in engineering design can be achieved from combining existing GRP concrete design guidelines with carbon steel design codes primarily made possible due to the increase in the constitutive properties of modern composite rebar or GRP. It also examines the technical and practical considerations necessary to both construct and ensure the integrity of composite rebar during transportation and handling on site and the measures taken by Franki-Cementation Joint Venture to ensure the safe deployment of the GRP in the workplace on the Noord/Zuidlijn Project in Amsterdam between 2003 and 2006.

Jan 1, 2006

By Rudolph P. Frizzi

"Abstract Pile design for building structures in the United States is typically performed by: 1) investigating and assigning engineering parameters to the respective ground bearing materials, 2) calculating ultimate pile to ground (geotechnical) capacity which is then reduced by a Safety Factor deemed appropriate by a registered Design Professional thereby arriving at an allowable pile geotechnical pile capacity, and 3) determining the required pile structural section using allowable pile section material properties. It is advantageous to use a Working Stress Design Method (WSDM) approach as one system of loads (service loads) are used in both the geotechnical and structural evaluation. There are a variety of methods used to determine the ultimate and allowable geotechnical capacity, and Building Codes often require a registered Design Professional to determine the appropriate method(s) and capacities. The International Building Code is the Code typically referenced in building design and construction in the United States. Structural design usually follows Building Code requirements and Allowable Stress Design (ASD) procedures. As design of the overlying structure typically follows a Strength Design Method (SDM) approach using factored loads, in some cases piling is first designed for pile-to-soil interaction using service loads, followed by evaluating the pile geometry for factored loads. Construction is the finalization and implementation of the designed piling. As such, project-specific technical specifications are typically developed by a registered Design Professional such that a project Owner can bid, buy, and instruct a Contractor as to the desired piling work and acceptance criteria. There are several Industry groups, including DFI, PDCA, ADSC, and ACI that provide guidance documents which the registered Design Professional can refer to in developing the piling technical specifications. It is the author’s opinion that the registered Design Professional is best suited to observe and verify the piling installation; many Building Departments require verification and documentation by a registered Professional as a condition of final acceptance.INTRODUCTIONPile design for building structures consists of: investigation, design, specification, and verification. In major metropolitan areas within the United States, Building Codes typically identify minimum requirements for each of the above steps. The International Building Code (ICC, 2012) is the Code typically referenced in building design and construction in the United States. Recognizing the ground conditions as well as piling construction means and methods can vary on a site-by-site basis, latitude is given to the registered Design Professional and Contractor to optimize the piling system for the respective project conditions. Field testing and quality control / assurance measures are typically implemented to verify the design intent is attained for the production pile elements."

Jan 1, 2014

By Shoichi Tsukuni, Akihiko Uchida, Kazuo Konishi

"In order to investigate the effect of grid-form deep mixing walls as a countermeasure for liquefaction damage to roads and private houses in Urayasu, Japan, three dynamic centrifuge model tests were conducted. Urayasu is located in the Tokyo Bay area, and private houses in the city incurred severe damage due to liquefaction during the 2011 Tohoku earthquake. In grid-form deep mixing walls design, the distance between grid-form walls is critical to prevent liquefaction. This study clarifies the relationship between the settlement of private houses and the distance between grid-form walls under the conditions that exist in Urayasu.INTRODUCTIONMany private houses in Urayasu, Japan suffered severe damages due to liquefaction during the 2011 Tohoku earthquake (Photograph 1). Fig. 1 shows the location of Urayasu and the maximum acceleration of the observed seismic waves in the Tokyo Bay area. At Urayasu, the duration of the seismic waves (hereafter called the Urayasu Wave) was about 2 min. The maximum acceleration was 1.57 m/s2 (Fig. 2), which is relatively small. The damages occurred in the land reclamation areas that consist of loose sand with an SPT-N value less than 10.To prevent liquefaction in future, it is necessary to adopt suitable countermeasures in the areas where many private houses suffered severe damages. Grid-form deep mixing walls are one such countermeasure. Fig. 3 and Photograph 2 show grid-form deep mixing walls. Walls are constructed using the deep cement mixing method. Fig. 4 shows a plane view of planned grid-form deep mixing walls for roads and existing private houses in Urayasu."

Jan 1, 2015

By Frank Haehnig, Kurt Kogler

"With a height of 200 m, a crown width of 626 m and a concrete volume of 1.6 million m³, the Kölnbrein Dam in the upper Malta valley in Carinthia / Austria is the largest concrete dam in Austria. Boasting a storage capacity of 200 million m³ with a received water load of 54 MN, this is one of the strongest arch dams in the world.During its construction from 1974 to 1977, the dam was equipped with a comprehensive monitoring system capable of comparing developing deformations and stresses with the design values.With a planned reservoir level of 1,900 m a.s.l. the dam saw the reservoir level of 1,860 m a.s.l. breached in the year 1978. This led to extremely high seepage losses of up to 200 ltr/sec and a rise in the foundation water pressure up to 100% of the dam’s height. These observations were caused by the development of horizontal cracks in the area of the middle dam blocks, between the lowest inspection walkway and the waterside.As a consequence, power plant operations had to significantly be reduced and a number of additional measures were carried out – though these did not lead to the desired sealings.The developer subsequently decided that the dam should undergo a general rehabilitation from 1998 to 1994 in accordance with a concept developed by Professor Lombardi. This concept involved erecting a 50 m high support structure with a concrete volume of 500,000 m³ on the airside of the dam, along with the addition of neoprene bearings to transfer 1.2 million tons of the horizontal load. These measures were able to reduce the deformations in the dam enough so that mostly load-bearing injections into the cracks in the dam’s concrete could successfully be carried out by way of targeted grouting measures using injection resin (RODUR) specifically developed for this purpose.In the years 1998 - 1994, a total of 130,000 m of grouting, monitoring and control drillings were executed, and around 200,000 kg of synthetic resin was injected into the cracks in the dam’s concrete.These measures have ensured the dam‘s uninterrupted operation since 1994. A number of small re- injections were again carried out on the contact surface in the years 2011 and 2012."

Jan 1, 2016

By Wendy L. Mathieson

The Bonneville Power Administration (BPA) will build about 500 miles of new 500-kV transmission lines in the next 5 years. Many new lattice towers will be built in remote locations or in environmentally sensitive areas. Therefore, micropile foundations were designed that could be installed in remote areas, in variable subsurface conditions, and in a manner that would reduce excavation volumes and potential erosion concerns. Typical lattice tower foundation axial loads range between 75 and 1,500 kips (300 to 6,700 kilonewtons [kN]) per leg, with uplift loads being slightly less than compressive loads. Lateral loads range from 5 to 320 kips (20 to 1,400 kN) per leg. Full-scale axial and lateral load tests were conducted in geologically representative soil units during the micropile design for the 9-mile-long (14-kilometer [km]), Kangley-Echo Lake transmission line that extends through a protected watershed east of Seattle, Washington. Micropile foundations for single and double circuit suspension and dead end towers were designed using these load test data.

Jan 1, 2004

By K. Viking

This article deals with some of the civil engineering related problems to be encountered when offshore wind energy projects transform from prototype offshore wind energy converter farms, developed and installed during the 1990?s, to commercial farms that?s currently planned to be built. The offshore wind energy converter (OWEC) installations encounter a wide range of problems, only partial of these are geotechnical. In Europe both onshore and offshore wind farms have, from a historical point of view, usually been founded by using the monopole technique, installed with traditional impact hammers, or by using gravitational foundations. However, the rapid development of bigger turbines and larger wind farms, together with increasing considerations of fatigue aspects, has lead to financial benefits of developing and exploring other foundation techniques. This paper reviews some Scandinavian experiences regarding critical components of the design phase in relation to connecting the superstructure to the ground, and some of the main considerations of how the loads applied to the structure are transferred to the surrounding soil.

Jan 1, 2013

By Van E. Komurka

This paper presents a cost comparison of the driven pile foundations for two large Wisconsin Department of Transportation (?WisDOT?) projects in Milwaukee, Wisconsin: the Marquette Interchange South Leg, and the Canal Street Viaduct. The projects? geology is fairly similar, but their methods/approaches to pile foundation design and installation differ. Although the Marquette Interchange South Leg had deeper poor soils, its pile design was more-cost-effective than the Canal Street Viaduct?s. Potential reasons for cost differences between the projects are identified, and the effect of the different design and construction approaches on economics is discussed.

Jan 1, 2009

By Timothy C. Siegel

Accurate representation of the geotechnical resistance distribution is critical in evaluating the performance of piles and pile groups for design. A current practice is to infer the geotechnical resistance distribution based on measured changes in strain during conventional top load pile testing. Especially for drilled and bored piles, the residual load is typically assumed to be negligible both during testing and after the application of the structure load. A practical result is that the compressive structural load is anticipated to be opposed primarily by the shaft resistance with little or no mobilized toe resistance. The predicted top deflection is estimated as the combined elastic compression plus the movement necessary to mobilize shaft resistance. The development of residual load (and associated negative skin friction) results in a significantly different design condition. Negative skin friction tends to force the pile into the ground and develops residual load in the pile that contributes to the internal compressive load. Significant toe resistance can be mobilized in order to resist the combination of negative skin friction and the sustained compressive load. The pile movement becomes a function of the toe penetration required to mobilize sufficient resistance to reach a balance of forces. In an effort to study the development of residual load in augered cast-in place (ACIP) piles, the authors installed and monitored strain gages that were embedded in an 18-inch diameter ACIP pile at a site in southeast Georgia. The results of this study indicate that residual load develops over time and reaches a distribution that is consistent with the principles of the unified design of piles. It is concluded that residual load develops in ACIP piles (as well as all drilled and bored piles by the same mechanisms) and that the residual load should be considered in the interpretation of load tests and in the pile design, particularly in the estimation of the single pile and pile group settlement.

Jan 1, 2009

By António A. Henriques, António Gomes Correia, Ana Teixeira

"Abstract Pile foundations are often used for important structures, and thus, reliability evaluation is an important aspect of the design. Reliability methods have become increasingly important as decision support tools in different areas. The main benefit of reliability analysis is that it provides quantitative information about the parameters (uncertainties) that most significantly influence the behaviour under study. In particular, the design of pile foundations still involves many limitations and uncertainties, particularly when there is not enough investment in soil characterisation and/or pile load tests. In addition to the uncertainties associated with soil characterisation, physical, statistical, spatial and human uncertainties exist. In this subject, the primary purpose of this paper is to demonstrate the application of reliability methods to geotechnical pile design (axial load). It also presents a simple and practical approach to performing it using Monte Carlo Simulations, intending to provide knowledge for code harmonisation and encouraging the development of such methodologies in geotechnical practice. Sensitivity analyses are shown to understand the influence of each uncertainty type coming from different sources. An application example indicates, corroborating other studies, that the model error is the most influent uncertainty. As such, when using the different models (SPT-, CPT- and PMT-based) for bearing capacity, the results emphasise the need for a well-defined and wellcharacterised resistance model, also these results allow the engineer to understand how important the load tests can be to achieve reliable results and economic designs.1 IntroductionUnlike the approach to reliability evaluation used in structural engineering, the traditional procedure used in geotechnical designs addresses uncertainties through high global or partial safety factors (SF), mostly based on past experience. However, this approach to addressing uncertainties does not provide a rational basis for understanding their influence on design.Furthermore, the new regulation codes and social concerns, such as the sustainability or the economy, are imposing geotechnical engineers to increase their ability to deal with uncertainty in a direct and more rational way. Designs should be economic, sustainable and reliable at the same time. Concerning the reliability part of design, different approaches can be done, but the most important thing to keep in mind is the simplicity and efficiency of the tools and applied methods."

Jan 1, 2014

By M. Reza Saberi, T. Ted Miyake

Driven piles are a common tool in any engineer’s toolbox for supporting large structures over very soft ground, especially in high seismic risk zones. Challenges include achieving sufficient vertical and lateral load capacities within the constraints of pile spacing and geologic conditions. This was the case for a project in Orange County, California with a state-of-the-art, $180 million plant for biosolids processing, biogas management and energy recovery located in marshland next to an existing waste water treatment plant. The new construction for the Irvine Ranch Water District included a 70-foot (21 m) tall building and three closely spaced, 90-foot (27 m) high, 65-foot (20 m) diameter, egg-shaped steel digester tanks. The lower 35-feet (11 m) of the tanks were constructed below ground level. The site was underlain by up to 45 feet (14 m) of highly compressible peat and organic clays with standard penetration test (SPT) blows as low as 2 blows/ft (30 cm). Some of the peat layers had measured in-situ dry densities of less than 30 pcf (480 kg/m3) with moisture contents of over 250 percent. The soft clays and peat were underlain by a dense layer of sand and gravel at depth. Groundwater was very shallow. While nearby sites were designated by others as seismic site class “D”, this site was clearly class “F” (SF) which required site specific seismic hazard and time history analyses. Six recorded time histories were selected from the 1994 Northridge, 1989 Loma Prieta (California) and 1999 Chi Chi (Taiwan) earthquakes for the ground motion analysis considering the magnitude of the earthquake, distance to the source, characteristics of the earthquake source (i.e. type of fault displacement), peak ground acceleration, local site geology, station type (i.e. free-field or small structure stations), and spectral content that was similar to the period range of interest. Following ASCE’s Guideline Document 7-05, a site-specific horizontal acceleration response spectra (ARS) was developed for the maximum credible earthquake (MCE) associated with the site.

Jan 1, 2018

By A. Holeyman

The displacement compaction piles described in the paper are installed using a heavy casing or tube and an internal drop hammer. The casing which initially is closed at the bottom by a sand plug displaces the surrounding soil during the driving. Additional sand is rammed down through the casing during the extraction of the casing. The applications and limitations of the method are reviewed in the paper. The importance of checking the sand compaction piles during and after the installation is stressed. Indications of the compaction of the surrounding soil during the driving can be obtained by comparing the initial and the redriving logs of the casing as well as from the volume of sand added. A method to estimate the increase of the mean cone resistance as measured by CPT tests in sandy and silty soils is presented. The governing parameters are the volume of the added sand, the granulometric index and the initial cone resistance.

Jan 1, 2010

By Nuno Cruz, Saúl Rodríguez

"When executing offshore bored piles there are several specific factors and problems to consider in order to guarantee excavation stability. One of the methods employed to carry out this type of work consists in setting up a floating work platform, typically a barge, and implementing a soil stabilization system that combines a partial steel guiding casing with third generation polymeric drilling fluids. The main aspects to take into consideration when performing offshore pile boring works are soil stabilization, project design, work methodology and operational aspects. An example of a work methodology problem arises before any pile boring work takes place as the steel guiding casing contains water, sometimes salt water. What to do with this water in order to replace it by an adequate polymer fluid will determine the stabilization capacity as soon as the shaft advances below the protection of the casing. Another example of operational problem may derive from barge movements while executing boring activities. This study is the result of extensive field data collection and concrete logging analysis from marine projects using polymers in different continents. The bored pile stability target was set ranging between 2% to 15% of concrete overbreak. Values above 15% or below 2% mean that there is a stability problem. Then the off-target pile’s data is collected, analyzed and classified under categories. Thus, a direct correlation is established between the problem category and the final results. Modifying steps in the pre-established construction methods or operational variables guarantees target results without the need to replace the approved construction methods. As a general conclusion, the worldwide experience in large diameter marine works, allows to provide truthful information and solutions for these problems. In knowing how to follow a logical sequence of work and applying adequate work methodology will be the key for success.GENERALBackgroundTo carry out the drilling process of offshore bored piles there are two main options to take into consideration: drilling the pile by using full guiding casing until final depth; or using a combined system of partial steel guiding casing and support drilling fluids.The knowledge and situations described in this paper come from the experience acquired in different projects where the second method was employed. This construction method consists in installing a steel guiding casing by vibration and thus covering the water table and further stabilizing the soil below it with polymeric fluids until reaching the pile’s final depth. The Fig. 1 schematic shows an example of this method where H corresponds to the length of the steel guiding casing whereas the remainder of the shaft’s length is stabilized by polymer fluid. The entire bored length is full of slurry up to top of casing.In most cases this kind of civil works results from the need to build a bridge or executing port structures in places where the creation of temporary artificial peninsulas with fill material is impracticable or not allowed. Hence the need to use floating work platforms, commonly referred to as barges."

Jan 1, 2017

By Klaus Pöllath

The Netherlands RandstadRail project makes use of a large range of sophisticated geotechnical techniques to allow a shield driven tunnel to approach the central station of Rotterdam. This paper describes the construction of three deep excavation pits constructed with 1.2 m and 1.5 m thick diaphragm walls. Besides the presentation of the actual diaphragm wall activities special consideration is given to the break-in and break-out situations of the TBM into the deep excavations pits using sealing blocks and partly glass fibre reinforcement in the diaphragm walls.

Jan 1, 2006

By Shane Baker

Cementation Foundations Skanska Ltd encountered many significant challenges in designing and constructing the foundations for the LNG (Liquefied Natural Gas) tanks and associated structures at the Isle of Grain, Kent, UK. With LNG cargo ship levels fixed by the adjacent English Channel, the platform could not exceed critical thickness in order to achieve final grade level, so a safe and efficient working platform for construction equipment on extremely poor alluvial soils was designed and installed. The detailed pile design also required particular analysis of the pile group behaviour and considered seismic load cases not usually associated with UK pile design. Continuous flight auger (CFA) piles were the chosen foundation solution and design was verified through preliminary and working pile tests both axially and horizontally. Contaminated land and existing foundations from a previous oil terminal meant that removal of spoil was extremely costly so specific measures were taken to minimise the off-site disposal. The management of a package of general Civil Engineering in addition to the piling scope, coupled with an unrelenting production program has forced a raising of the bar for this foundation technique.

Jan 1, 2006

By Sanket Rawat, Ravi Kant Mittal, Vikash Prasad

"The understanding of the response of pile foundations under various types of loads is a necessary prerequisite to analyze and design them properly. Therefore, this paper highlights and compares the provisions available in Indian Standard IS 2911:2010 to estimate the capacity of laterally loaded pile foundation with the provisions available in different country codes and existing literature. Comparisons are made between the Indian standard method, Broms method and Matlock & Reese method for the analysis of laterally loaded piles due to popularity and prevalence of the later methods in design offices worldwide. This has been achieved using a parametric study on pile embedded in pre-consolidated clay and sand for both fixed head and free head case in terms of displacement and ultimate load capacity. It has been found that there are various limitations to the Indian Standard method associated with various cases such as short pile analysis, complete moment distribution etc. Therefore, suitable recommendations have been made on the basis of the above comparison to improve the accuracy of the design in Indian perspective. The proposed comparison and subsequent area of improvements will present the design engineers all across the globe, a broad sight of design specifications of laterally loaded piles.INTRODUCTIONPiles in groups are very often subjected to both axial and lateral loads. In the 1960’s, designers used to assume that the piles could carry only axial loads and the lateral load is to be carried by batter piles. However, later, a large number of load tests authenticated that vertical piles also can transfer lateral loads through shear, bending, and lateral soil resistance rather than purely acting as axially loaded members. Initial attempts to analyze laterally loaded piles used the finite-difference method, as described by Howe (1955), Matlock and Reese (1960), and Bowles (1968). Matlock and Reese (1956) used the finite difference method to get a series of non-dimensional curves to enable the user to input the appropriate curve with the given lateral load and estimate the ground-line deflection and maximum bending moment in the pile shaft. Later, Matlock and Reese (1960) extended the earlier curves to include selected variations of soil modulus with depth."

Jan 1, 2017

By Jelke Dijkstra

This paper presents the results of model pile load tests in a photoelastic material. The soil in this test is represented by an assembly of photoelastically sensitive glass particles, which allows for optical measurements of stresses. In the same test setup, displacements around the pile are measured using digital image correlation (DIC). During the pile installation stresses and strains are recorded. Tests were performed in loose and medium dense particle assemblies. The development of stresses and strains around the pile tip and pile shaft are quantified and presented in this paper. For the loose conditions the results show a small influence on the stress state. For the medium dense conditions a clear stress change is observed.

Jan 1, 2006