Search Documents

By N. I. Tyushkova

On the basis of detailed studying of mineral structure of ore and treatment products it is established that the given ore refers to oxidized Pb-Zn vein-disseminated ores. Technological special features of the basic ore minerals and the reasons causing their obstinateness that is defined by following features are revealed, presence at dominating quantity difficult to float lead minerals: mimetesite (9.67%), green lead ore(0.48%); non float: bindheimite (2.16%) and plumbojarosite (0.36%) and high assay of oxides and hydrous ferric oxides; also thin, emulsive and submicroscopic segregations of the defined minerals in swamp ore. As a result of researches the scheme of gravitational-flotation treatment was conducted in semi-industrial scale. It allows to receive two concentrates from ore: a lead gravitational concentrate of mark ??-4 with the assay of 55.5 % of Pb and 0.77 % of Zn; and a Pb concentrate of mark ??-7 with assay of Pb of 40.97 % and Zn of 1.39 %. The total assay of Pb in concentrates makes 81 %. The efficiency offered by gravitational-flotation schemes is defined by possibility for recovery of big impregnated lead minerals under gravitation. The use of this method of gravitation has allowed to recover such mineral as beudantide and to exclude irrevocable losses of lead in tails which are connected with this mineral. Scientific value of the presented researches is connected with the fact the problem of extraction of the oxidized minerals of Bb and Zn is rather difficult and insufficiently studied. Keywords: flotation, oxidized forms of Pb and Zn

Sep 1, 2012

By Knut L. Sandvik, Erik Larsen

Crystalline silicon solar cells are the most important solar cells manufactured today. This will most probably remain the situation the next decade. The future silicon feedstock is most likely not reject from the production of electronic-grade silicon. There will probably be a more direct solar-grade silicon route, excluding the electronic-grade silicon "detour". Estimated global solar energy demand in 2001 required approximately 5,500 tons of silicon feedstock. This required 65,000 tons of quartz. If the trend continues, the solar energy demand in 2010 would require approximately 30,000 tons of silicon feedstock and 350,000 tons of quartz, although the need for quartz probably will be lower than this. Quartzite has been regarded as the most suitable primary raw material used in the silicon solar cell production chain. This may change as the raw material requirements for the production of metallurgical-grade silicon are most likely to change. In addition, quartz or other silica-containing minerals from other rocks may be of a higher purity or contain lesser amounts of the most harmful elements. This favours increased beneficiation of primary raw materials in the future solar silicon feedstock production chain.

Jan 1, 2003

By Han Long, He Fayu, Sun Chuanyao

In global mining sector, when people mention "China Factor", usually they refer to China’s huge demands for mineral commodities, which had been driving the world mining industry into late "Super Circle". Few people pay attention to Chinese research capabilities and resources, which actually grows with Chinese economics in last three decades in such a soaring speed that you can simply feel it by the number of papers and attendees in recent IMPCs. In China, currently there are 33 universities and colleges where mineral processing discipline is established, and more than 20 research institutes dedicated in mineral processing area, with the largest number of students, teachers and researchers in the world. Due to the characteristics of Chinese mineral resources, Chinese researchers have made tremendous efforts on R&D of the process and reagents for those low grade, fine dissemination, and complex minerals resources, such as low grade hematite, diaspore, complex poly-metallic sulphides, as well as those minerals rich in China, including scheelite, cassiterite, and rare earth etc. with a special emphasis on the comprehensive utilization. Those research achievements not only successfully commercialized in China, but also have great potential for international cooperation. With continuation of globalization , Chinese government has been encouraging the international R&D cooperation in various areas at all levels, and the funding mechanism is well established with more 400 projects were sponsored in last year,in which,however, the mineral processing related projects are very few. Considering the fact that a large number of Chinese companies or Chinese capitals investing in the mining sector worldwide, more opportunities for international cooperation in this filed wouldbe emerging and increasing, while the factors like complementary, IP, government policy, system and culture difference still need to be addressed properly.

Jan 1, 2014

By M. M. Fan

In Florida?s phosphate industrial practice, the most favorable upper size limit of froth flotation is 1.18 mm which corresponds to particle weight of about 2.8 mg. Conventional froth flotation is not efficient in upgrading coarse particles (+0.425-1.18 mm). A limited number of studies have been devoted to understanding and improving coarse particle flotation. We have shown that the coarse particle flotation performance can be significantly improved by the presence of picobubbles generated by hydrodynamic cavitation. In this study, the size of picobubbles produced under certain hydrodynamic conditions was measured by a laser particle size analyzer. A size-by-size flotation performance analysis of coarse phosphate froth flotation in the presence of picobubbles is conducted in terms of flotation kinetics, selectivity and recovery. It was found that picobubbles doubled the flota-tion rate, increased the P2O5 recovery more significantly for +0.85-1.18 mm particles than +0.425- 0.6 mm and +0.60-0.85 mm particles. At a given acid insolubles (A.I.) rejection, the presence of picobubbles increased the P2O5 recovery by up to about 25%.

Jan 1, 2014

By A. V. Nguye, P. A. Harvey

Previous studies have reported that inorganic electrolytes can enhance floatability of coal. The research has shown that the enhancement, if any, is highly dependent on changes in solution pH, type of electrolyte, and electrolyte concentration. The reasons for this are still not clear. In this study the floatability of coal particles in mono and divalent salt solutions was investigated. The zeta potential and hydrophobicity of the coal was measured experimentally, and a modified Hallimond tube was used to determine the floatability of coal particles by single bubbles, where the collision efficiency was equal to unity. The experimental information was used in conjunction with the Hogg-Healy-Fuerstenau equation to quantify the electrical double layer interaction. It was found that for low electrolyte concentration (less than 0.1 M) solutions the flotation recovery of coal particles was less than that for distilled water, and decreased with increase in concentration. Conversely, at electrolyte concentrations above 0.1 M, flotation recovery increased with increasing concentration. Both of these results are consistent with previous observations, but are inconsistent with expectations when considering the possible influence of electrical double layer interaction. A possible mechanism, based on the existence of the pre-existing submicron-sized gas bubbles, known as bubstons (i.e. bubbles stabilized by ions), present in water in close proximity to the hydrophobic coal surfaces is discussed in line with the early observation of flotation improvements by microbubbles “nucleating” on hydrophobic surfaces. In particular, the dependence of the bubble-particle attachment efficiency on electrolyte concentrations supports hypothesis on the salt-dependent and ion-specific existence of bubstons. However, a theoretical explanation of the transition salt concentration (at about 0.1M) is deficient at present. The existence of these submicrobubbles in close proximity to hydrophobic surfaces is not trivial. They can (as can individual gas molecules or other solutes) mediate and extend the range and magnitude of the attraction between hydrophobic macroscopic surfaces. These bubbstons may explain the curious phenomena of the socalled long-ranged hydrophobic attraction measured with the Surface Force Apparatus and Atomic Force Microscopy, and the slippage at hydrophobic surfaces. Finally, the coalescence of bubbstons affects the rupture of liquid films at a very large thickness (over 100 nm), observed, but unexpected, by flotation chemists.

Jan 1, 2003

By V. Panayotov

Flotation practice usually uses the Sheridan-Grizvold selection method, where zinc minerals are activated by addition of copper sulphate and depressed by addition of sodium cyanide, ferrous sulphate, zinc sulphate or various mixtures of these reagents. The method is suitable for the flotation of sulphide ores, which, do not bear precious metals, such as silver and gold. When classical technology with cyanide is applied to depress zinc minerals, the precious metals, which are contained mainly into lead minerals, are dissolved into the solution, which represents a technological loss. In order to avoid this process, we have made use from the knowledge on the semiconducting properties of lead and zinc sulphide minerals. We have changed the surface charge of minerals by means of an electrochemical impact realized by direct current application and specially designed set of insoluble or semi-soluble electrodes. Thus, flotation separation of lead and zinc sulphide minerals was achieved, at increased recovery of lead, zinc and silver. The technology proposed was implemented in a Bulgarian flotation factory; it worked over 5 years providing significant, positive economic, technological and environmental impact. Silver recovery was increased by 0.8-1.0 %, and lead and zinc recovery was increased by 0.8-1.0 %. The technology is easily controllable and adaptable to raw materials and parameters of the technological process. It can be paid back for 6-8 months after the implementation. Keywords: lead-zinc flotation separation, electrochemical impact

Sep 1, 2012

By Ernesto de la Torre, Karla Velín, Alicia Guevara

"The following study shows the improvement and simulation of a gold recovery plant of 24 t/day of capacity by gravity concentration, flotation and leaching. The ore processed had grades of 6 g/t Au, 15 g/t Ag, and 0.69 %Cu with the mineralogy consisting of 2 %chalcopyrite, 12 %pyrrhotite, 7 %plagioclase and 50 %quartz. The recovery process starts with crushing the ore followed by grinding it further in a ball mill. The ground ore is then concentrated in a Falcon centrifugal concentrator with concentrate being processed by amalgamation process. Gravity tails are sent to a flotation circuit where the copper minerals and some gold are concentrated. Lastly, the flotation tailings undergo cyanidation for gold recovery. Currently, the overall recoveries are 82.8 %Au, 49.6 %Ag and 99.1 % Cu. The optimization was developed in the laboratory using a Wilfley table by gravity concentration. Flotation tests in the laboratory were performed using potassium amyl xanthate and pine oil. Lastly, cyanidation was then performed on the flotation tailings. The results showed the optimum concentration of sodium cyanide in cyanidation is 2 g/L, which produced an increase in gold recovery from 30% to 44%. The reduction of diameter particle from 132 to 80 µm also produces an incremental recovery of gold and silver from 11% to 21% Au and 0.4 to 3% Ag in gravity concentration. Likewise in the cyanidation the recovery of gold and silver has shown a rise from 44 to 62% and 8 to 32% for Au and Ag respectively. However, the flotation method the gold recovery is reduced from 68 to 30% Au by reducing the particle size. Computer simulations using the programs, Moly-Cop and ModSim were performed to determine optimum parameters for the recovery of precious metals at the gold recovery plant."

Jan 1, 2014

By Hajime Miki, Mutia Dewi Yuniati, Tsuyoshi Hirajima, Keiko Sasaki

Acid mine drainage is mainly due to pyrite/arsenopyrite oxidation processes, and suppressing such processes is important issue. As a promising process it is reported that silicate ion can complex with catechol (1,2-dihydroxybenzene) and this complex is oxidized to a solid silica layer on the surface of those sulphide minerals. Detailed behavior was investigated from the result of electrochemical experiments. Results of polarization potential showed that oxidation peak can be seen only in the presence of both silicate ion and catechol addition at this peak potential and this peak can be identified as silicate-catechol complex oxidation to silica. Potentiostatic experiments indicated the dissolution kinetics of pyrite. Untreated pyrite dissolution rates were higher than pyrite treated with catechol and silica solution. To enhance the silica layer reaction on pyrite, the pyrite potential was held at 550 mV vs. SHE in catechol silica solution. This pyrite dissolution kinetics was almost the same as untreated pyrite. Potential hold followed by drying for 30 min process resulted in much lower pyrite dissolution rates. Drying is important for development of the silica layer. Analysis of this potentiostatic curve provided a way to estimate the thickness of the produced silica layer and kinetic information of treated/untreated pyrite. Untreated pyrite showed thinner initial layer thickness on the surface of pyrite (oxidized passive layer, not silica) and higher oxidative kinetics of pyrite compared with silica-coated pyrite.

Jan 1, 2014

By N. Kgabi, F. B. Waanders, E. Vinken, A. Mans

"Mössbauer and SEM identification of the iron mineral phases present in South African coal fractions from the Free State, Gauteng, Mmpumalanga, Natal and Waterberg coal fields, as well as from ash samples from coal used in the Lethabo power plant, containing a large amount of inorganic matter, was conducted. The iron is mainly associated with sulphur in the mineral but the amounts of these and other minerals vary considerably in coals from diverse origins. By means of Mössbauer analyses the iron bearing minerals were identified as pyrite, jarosite, illite and ankerite. In the SEM analyses quartz, associated with various clay minerals was identified with differences in abundance found between the coals from the different locations.The fly ash, produced at the high combustion temperatures in the power plant, gave rise to a spectrum, typical of a glass. SEM analyses showed that agglo- meration of the fly ash was due to the presence of Ca in the coal. The lab. produced fly ash was combusted at temperatures ranging from 200-1 200°C and the pyrite changed partially to hematite and partly into the glass due to the presence of the quarts and the clay minerals. A similar spectrum as the power plant fly ash spectrum was obtained.In the weathering experiments the pyrite changed to a sulphate component in a very short time during air drying."

Jan 1, 2003

By Rebecca Hope, Derick Moolman, Frikkie Malan

"Despite the lip service that has been paid to pro-active plant maintenance processes over recent years, a significant portion of maintenance in industry is still reactive. The business driving force to prevent expensive production opportunity costs arising from “break-down maintenance” is obvious. Various benefits can be derived from successfully deploying remote equipment diagnosis technology and associated business processes.From an end-client’s viewpoint these include the ability to predict and take actions to prevent equipment breakdowns, increasing the lifetime of equipment by responding to appropriate operating instructions and therefore improving the return on capital expenditure. Better planning and scheduling of maintenance priorities and resources with performance measures like an Equipment Health Index are also possible. The knowledge that a qualified supplier engineer is constantly in touch with the operating conditions of their equipment, albeit remotely, is more than a comfort, and can be translated into quantifiable cost savings and improved supplier service levels.This paper analyses the reasons for the inadequate level of pro-active plant maintenance practice in industry today, and presents a number of important criteria in selecting appropriate solutions to this problem. A case study of a specific real-time, remote equipment management application is presented."

Jan 1, 2003

By E. V. Bratygin, E. G. Dmitrieva

The aim of the research was to study the thermodynamic characteristics of high-temperature processing of ilmenite concentrate deposits "Central" in a neutral and oxidizing atmosphere, as well as its interaction with alkaline additives. The research was conducted using a scanning colonoscopy on thermogravimetrical analyzer NETZSCH STA 449 F3. A sample of the test material weighing 10 mg was placed in a crucible and heated at a rate of 10 °C/min to 1200 °C in argon or air. Studies have been conducted pure ilmenite concentrate and its mixtures with 5 % and 12.5% of sodium carbonate. The results of the analysis of the thermogravimetric curves it was found that the recovery of the concentrate carbon will come from ulvospinel, not pseudobrookite, and the reaction recovery is possible at temperatures above 900°C. While removing produced in the decay ilmenorutile of iron oxides in an inactive form, for example, iron (III) oxide, it is possible to reduce the quantity of the solution of ilmenite formed during the restoration of the melt anosovite. The analysis of data obtained during heating of ilmenite concentrate with sodium carbonate in concentrations of 5 and 12.5% transition pseudobrookite in ulvospinel is missing, it just breaks down into hematite and titanium oxide, which, in turn, react with N?2??3. It should be noted that increasing the concentration of sodium carbonate in the sample contributes to more complete interaction of iron oxides and N?2??3 with formation of ferrites of sodium. This can ensure full recovery of iron oxides in the concentrate, which is part of secondary ilmenite can not be dissolved in the melt formed by the lower oxides of titanium. In addition, the increase in the content of soda in the mixture significantly reduces the temperature of the initial melting point of the slag and facilitates the coagulation of metallic iron.The obtained results were used for laboratory studies of the solid-phase sintering of briquettes from ilmenite concentrate with additives of sodium carbonate and a reducing – coal, as well as for the development of technological mode of solid-phase sintering of the concentrate with the aim of obtaining product recovery with a titanium dioxide content of more than 75 %.

Jan 1, 2018

By A. J. Lynch, L. Ergun, M. Oner

"A research program on modelling cement grinding circuits has been in operation at Hacettepe University, Ankara, for four years. It has concentrated so far on tube mill and air separator grinding circuits for cement clinker, with emphasis on plant sampling surveys, including axial sampling inside the tube mills. The data used for model development have come from 33 surveys in 9 plants.The operating conditions have been:- mill sizes - 3.2 to 4.8 metres diameter and 8.5 to 15 metres long,- mill feed rates - 46 to 158 tonnes per hour,- air flow through mills - 25000 to 125000 cubic metres per hour,- cement clinker work indexes - 10.3 to 18,- separator sizes - 2. to 3.1 metres diameter,- separator feed rates - 132 to 689 tonnes per hour,- separator speeds - 12.3 to 21 metres per second.The ball mill model is Whiten’s perfect mixing model and the separator model is the Tromp curve with a fish-hook. This paper emphasises the importance of calculating the breakage rates and the discharge functions with three case studies at five different circuits which were selected for discussion because they show how particular features of circuit operation can be included in the general models. Size distribution graphs are used to illustrate every aspect of the discussion"

Jan 1, 2003

By Gus Van Weert, Samuel A. Bolorunduro, David B. Dreisinger

"INTRODUCTIONThe objective of this work was to deport silver into a residue suitable for subsequent extraction without compromising the high base metal extraction during the pressure oxidation.RESULTS AND DISCUSSIONThe complex sulphide from the tailing pond of Cannington mine, Australia, was re-grounded and a bulk concentrate was recovered by flotation. The major economic sulphides are galena and sphalerite. The chemical analyses revealed 17.22% Fe; 4.88% Zn; 8.22% Pb; 9.49% S2- and 422 g/t Ag. The baseline cyanidation yielded 36.60% of silver at high cyanide consumption (24.17 kg/t NaCN). Pressure oxidation at 150°C (in the absence of iodide), followed by cyanidation of the residue yielded 8% silver extraction. Pressure oxidation was carried out at 110-150°C in sulphate media with additions of potassium iodide and the resulting residue was subjected to cyanidation. High recovery of silver was achieved because its incorporation into lead-hydronium jarosite during the pressure oxidation was minimised, while its deportment into the cyanide-soluble silver iodide was favoured (Figure 1). Silver recovery decreased slightly at high temperatures (140° and 150°C) because of the enhanced stability and kinetics of leadhydronium jarosite, but this could be overcome by increasing acidity and iodide concentration of the slurry."

Jan 1, 2003

By Fedotov Pavel

"Today the main objective of improving the process of ore dressing is to reduce energy consumption and performance of the basic rule of auxiliary enrichment processes. One of the modern means of ore destruction with a minimum of energy consumption is the interparticle fracturing, for example in the roller press. There still remain the unsolved problems of the energy consumption determination and the particle size distribution of the crushing product .Existing methods for determining these parameters are empirical and require considerable expenses and time. The improved finite element was developed to solve these problems using finite element contact interaction of the rock. Also it was developed to clarify the stress-strain and the rock fracture energy in a layer. These elements are used to study ore destruction in the layer and allows to create a model taking into account the interaction of crushing particles surfaces. The same algorithm was developed determining crushing product particle size distribution in the layer on the base of the Bond’s theory of crushing. The presented finite element model allows to determine the quantity of strain energy and particle size distribution of crushed product during the destruction processes of the material in the roller press with fair accuracy."

Jan 1, 2014

By Hamid-Reza Manouchehri, Hassna Aitahmed-Ali, Stellan Sundberg

"In flotation practices as the particle size becomes fine, e.g., p<20µm, the process efficiency declines markedly. When flotation of fine particles is necessary, one method to improve the recovery is selective agglomeration of fines. Different agglomerating methods have been introduced and tested; however, one method which has recently received great attention is to aggregate fine particles by magnetic force. A selective aggregation of the fine paramagnetic particles, e.g., sulfide minerals, can be achieved by applying a high intensity magnetic field during flotation conditioning. The method is simple, selective and effective for fines, and has a low operation cost. However, a minimum magnetic susceptibility of fine grains is required for this process. This method has been demonstrated in different sulfide minerals flotation plants. The implementation of the magnetic conditioning device, ProFlote, in both the Cu-Pb and the Zn circuit of Boliden’s Garpenberg plant in Sweden, where a complex massive sulfide ore is treated, is discussed herein. The preliminary results have shown an increase in the recovery of value minerals, in particular Zn and Ag and considerable reduction in Zn deportment to the final tail. Increases in Cu grade and decreases in Pb grade in Cu-con have been achieved as well."

Jan 1, 2014

By Kazutoshi Haga, Atsushi Shibayama, Altansukh Batnasan

"The aim of this study was to develop a hydromellurgical processing for removal of arsenic from high-arsenic copper sulfide ores and concentrates, providing increase in copper recovery. In this study, three different enargite ore samples containing 28.2–46.7% copper, 1.9–15.0% arsenic and 10.6–27.5% iron were used to determine optimum conditions for the extraction of copper and removal of arsenic. High pressure oxidative leaching process was preformed using various leaching reagents such as sulfuric acid (H2SO4), ferric sulfate (Fe2(SO4)3), hydrochloric acid (HCl), ferric chloride (FeCl3), sodium sulfate (Na2SO4), sodium chloride (NaCl) solutions and distilled water (DW), respectively, under the fixed conditions which were selected to be as follows: NaCl concentration, 0.34 M; concentrations of other leaching reagents, 0.1 M; particle size, -45 ?m; pulp density, 100 g/L; agitation speed, 750 rpm; leaching temperature, 160 ?C; leaching time, 60 min and total pressure (oxygen gas and vapor pressure) into an autoclave, 1 MPa. Results show that under the leaching conditions, more than 90% of copper leaching was achieved with lower than 2% arsenic content as a consequence of the formation of arsenic precipitates in a solution of Fe2(SO4)3–NaCl. It was determined that copper, arsenic and iron concentrations in the pregnant leach solution were 42 g/L, 0.3 g/L and 0.3 g/L, respectively. As a result, it can be concluded that the Fe2(SO4)3 solution in the presence of NaCl or FeCl3 are more efficient leaching media compared to other leaching agents under the high pressure oxidation conditions, because of their high copper recovery and lower arsenic level in the pregnant leach solution.INTRODUCTION Generally, copper is usually produced from copper sulfide ores by a combination of several processes which are flotation and smelting followed by refining [1-3]. Arsenic content in copper sulfide ores tends to increase due to the depletion of high grade copper deposits, hence conventional mineral processing and metallurgical processes cannot effectively treat these ores containing high levels of arsenic to obtain consistently high purity copper concentrates. Because high levels of arsenic in copper ores/flotation concentrates reduces the value of concentrates due to the restriction of smelting process and causes it to be a source of environmental pollution [4-6]. From this point of view, the known way of prevention against high-arsenic copper sulfide concentrates in further metallurgical treatments is to develop economically and environmentally competitive technologies for removal of arsenic impurity from copper sulfide ores before treating the ores/flotation concentrates by the pyrometallurgical routes."

Jan 1, 2018

By Slobodan B. Vujic

"For the requirements of the mining company “Rudnik-Rudnik”, engaged in undergr-ound exploitation of polymetallic ore and lead, zinc and copper concentrates production, the Department of Computer Application of the Faculty of Mining and Geology, University of Belgrade, designed a computer supported and integrated information-management system. This paper presents a concept of this system covering both monitoring and management of production in ""Rudnik-Rudnik"".The ""Rudnik"" Rudnik, Yugoslavia is a mining company, engaged in underground exploitation of polymetallic ore and production of ore, zinc and copper concentrate as well as other metals such as silver, bismuth and cadmium. This mining company runs stable business activities and undergoes a permanent growth of valuable production volume.The basic characteristics of production-technical system of ""Rudnik"" company are: uniform and up-todate technical-technological solutions: linking of production chain from underground exploitation of ore to flotation, namely final product - concentrate of lead, zinc and copper; complete mechanization of production; relatively low level of computer technics implementation; namely, ununiformed implementation of different application of computer-supported information technologies in production and business activities of the Company.These are the assumptions on the basis of which the management of the Company made a decision, in 1999, to upgrade information-management functions through development and application of modern integrated and computer-supported production-business information-management system (hereinafter: IMS, namely IMS Rudnik). For this purpose the Company requested the Department of Computer Application, Faculty of Mining and Geology, University of Belgrade to make the Project on IMS for their needs."

Jan 1, 2003

By V. A. Chanturiya

The state-of-the-art of mineral mining and metallurgy industry in Russia is characterized by high demand of nonferrous, rare, rare earth metals, and highgrade coal, on the one hand, and by involvement of natural and technogenic minerals with low content of valuable components, fine (nearly emulsion) dissemination of valuable components and close physicochemical and process properties. This calls for high-productive and ecology-friendly technologies for more efficient mineral beneficiation based on intensification of operating and new methods to extract valuable components from rebellious ore and technogenic minerals, relying on the last achievements of basic sciences, combination of dressing and chemico-metallurgical processes and using advanced pyro- and hydrometallurgical technologies. The transition to a new strategy of processing is only possible based on the new technological–mineralogical appraisal of a mineral raw material. Actually, the process mineralogy has a stock of modern high-resolution physical methods for analyzing composition, structure and properties of geomaterials, inclusive of micro- and nano-levels: - Identification of micro- and nano-size noble metals, and natural and induced formations on mineral surface; - Experimental validation of structural phase and chemical transformation of minerals under different energy input; - Justification of choice and mechanism of interaction between flotation agents and noble metals with complex material constitution; - Analysis of structural, phase and chemical transformations of sulfides and rocks under leaching. Thus, process mineralogy is an informational background for a unified theoretical approach to scientific justification of flowsheets of efficient mineral processing. The article gives a brief review of practices that have found application and proved to be of high economic efficiency. Such practices are: X-ray radiometry and photometry separation (Uchalinsky and Gaisky Mining and Processing Integrated Works of ALROSA); selective disintegration (equipment engineered by Mekhanobr-Tekhnika and IPKON RAS); process selectivity enhancement (IPKON RAS, Central Research Institute for Geological Exploration of Nonferrous and Noble Metals, Chinakal Institute of Mining, Siberian Branch RAS, etc.); bacterial gold leaching (Olimpiada MPIW, technologies developed the Central Research Institute for Geological Exploration of Nonferrous and Noble Metals, Nezhdaninsky deposit projects, etc.); combination processing at a mining and metallurgy plant (Norilsk Mining and Metallurgical Company, Yaregsky deposit projects and others); processing of waste: overburden, mill tailings, slag, etc. (Kovdorsky MPIW, Svyatogor JSC, Ural Mining and Metallurgical Company, plants designed by the Central Research Institute for Geological Exploration of Nonferrous and Noble Metals, Mining Institute of Kola Science Center RAS, Research Institute for Chemical Technologies); water conditioning in mineral dressing circuits (ALROSA, equipment by IPKON, etc.); utilization of process water (ALROSA, Ural Mining and Metallurgical Company, Severalmaz JSC and others). Thus, Russia this time has the academic and engineering background for development of efficient energy-saving technologies for comprehensive advanced processing in accordance with the world’s standards, or even higher in terms of a number of the technologies, which has continually been highlighted by participants of recent international congresses on mineral processing.

Jan 1, 2018

By Vasily V. Lodeischikov, Adolf F. Panchenko, Olga D. Khmelnitskaya, Vladimir E. Dementyev

Pilot plant tests of underground gold leaching from Maminskoye deposit oxide ores at a grade of 0,7 g/t Au were carried out. The underground leaching flow sheet includes Au dissolution by chlorine-containing solutions, Au adsorption from solution on active carbon, carbon concentrate ashing and calcine melting to produce high grade gold concentrate. The underground leaching system throughput was 15 m3 of solution per hour. Gold concentration in pregnant solutions was 0.12-0.13 mg/l. Gold recovery from solutions into carbon was in the range of 63-84%. It was demonstrated that the low Au recovery in the adsorption cycle was due to the presence in pregnant solutions of "active" chlorine, which destroys active carbon and causes a sharp decrease of the carbon loading capacity for gold. To improve the adsorption indices, previously dechlorinated pregnant solutions using bituminous coal or Na2S2O3, is recommended. Ion exchange process was tested as an alternative for gold extraction from dechlorinated solutions. In the testwork period, 4.4 kg of gold were produced with a chlorine consumption of 3.5 kg per 1 g of gold. During the tests a program of environmental protection measures was completed to provide the necessary safety precautions of the underground leaching works.

Jan 1, 2003

By Stephen Gay, Dewetia Latti

"When improving a plant a mineral processing engineer would like to know the mineral composition distribution. In order to assess this distribution in particles, as compared to the corresponding distribution in particle sections, a procedure needs to be applied to the observed particle sections. Such a procedure is called a stereological correction. There exists many stereological correction procedures, but one group of such procedures is based on using those stereological equations that do not require making assumptions regarding particle shape or texture.In particular Davy derived an equation to estimate the covariance of mineral composition distributions for particles from both particle sections and linear intercepts. Furthermore, this covariance can also be used to measure the variance of the composition distribution of each mineral.This paper shall present results verifying this equation. The experimental method was based on obtaining particle information from serially-sectioned particles. Particle samples selected for serial sectioning displayed a range of natural textures including liberated, binary and composite particles. The exposed surface of the polished sections were analysed using QEM*SEM. This procedure was repeated until all of the grains have been polished away. The covariance of mineral distributions were calculated from the serial sections and compared with that calculated using Davy’s equation."

Jan 1, 2003