Search Documents

By K. A. Natarajan

"Interaction with microorganisms results in significant surface chemical changes on minerals. For example, chemolithotrophs such as Thiobacillus ferrooxidans and Thiobacillus thiooxidans significantly alter the surface chemistry of several sulfide minerals such as pyrite, chalcopyrite, sphalerite and galena. Heterotrophic bacteria such as Bacillus sp. could alter the electrokinetic properties of oxide minerals such as hematite, alumina, silica, kaolinite and calcite. Microbe-mineral interactions could thus be beneficially utilised in mineral beneficiation as different from bioleaching. Microbially induced mineral beneficiation unlike bioleaching deals with interfacial phenomena at mineral-solution-bacteria interfaces and surface chemical changes are brought about at very rapid rates amounting to a few minutes resulting in mineral separations in an aqueous medium.In this paper, the role of acidophilic chemolithotrophs such as Thiobacillus thiooxidans and neutrophilic heterotrophs such as Bacillus polymyxa in the beneficiation of sulfide and oxide minerals is illustrated. Mechanisms of bacterial attachment on various sulfide and oxide minerals are outlined with respect to the influence of bacterial interaction in bringing about mineral surface hydrophobicity or hydrophilicity. The role of bacterial cells as well as metabolic products such as bioproteins and exopolysaccharides in significantly altering the surface chemistry of sulfide minerals such as sphalerite and galena and oxides such as hematite, alumina, silica and calcite is discussed with probable mechanisms. Possibilities of generating mineralspecific bioreagents are outlined with respect to bacterial adaptation to mineral substrates."

Jan 1, 2003

The air recovery from a flotation cell is the fraction of inlet air which overflows the weir as un-broken bubbles. The air recovery is an important factor in froth phase phenomena; such as gangue entrainment and froth recovery. Increasing the air recovery, results in a higher recovery of attached mineral particles. Air recovery can be measured experimentally on plant using image processing of the top surface of an overflowing froth. The air recovery is directly linked to froth stability and the bursting rate of the bubbles at the froth surface, making it very difficult to predict. Experimental results show a very strong correlation between the superficial velocity of the inlet air and the superficial velocity of the air leaving the cell through the froth surface due to bursting, calculated from the experimentally measured air recovery. This correlation holds over multiple banks from different plants. Development of a power law equation around the inlet air velocity and the bubble solids loading on the froth surface allows the superficial air velocity through the top surface of the froth to be predicted, and from this the air recovery. This model is valid for use when operating beyond the peak in air recovery.

Jan 1, 2014

By Sonia Helle, Ursula E. D. Kelm

"From a metallurgical point of view, acid leaching of oxide zone copper ore is considered in the first place in terms of ore grade, whole rock mineralogy, rock granulometry, crushed aggregate size distribution, porosity, permeability and corresponding fluid flow characteristics. Despite exhaustive physicochemical and general mineralogical characterization, drops in copper recovery occur and are often attributed to and “unquantified mineralogical misbehaviour” of the gangue phases. This study establishes an experimental link to monitor and quantify the chemical interaction of chrysocolla, malachite and atacamite with reactive gangue phases.Laboratory-scale sulphuric acid (15%) leaching in small columns is carried out using a synthetic rock composed of 57% quartz, 1% ore phase, and 42% reactive gangue. Gangue phases were selected to represent mineralogy found in argillic, advanced argillic, and propylitic alteration zones. Exotic copper ores of Codelco Norte (in particular Mina Sur) served as model for the modal distribution of mineral phases. Natural reactive gangue phases (<200 Tyler mesh) were chosen as pure as possible: Saz-1 and Swy-1 montmorillonites, KGa-1B and KGa-2 kaolinites (all Clay Mineral Society, USA, Source Clays) Nau-2 nontronite, Imt-1 illite (both Clay Mineral Society Special Clays) and Chilean mordenite, laumontite and bentonite. Ore phases are: mineraloid chrysocolla from Radomiro Tomic (Codelco Norte), reagent grade malachite and a purpose synthesized atacamite-paratacamite mixture. Complete chemical, physicochemical and mineralogical characterizations were carried out for ore and gangue phases.The following observations hold for samples with and without mineralization: Smectite-rich gangue increased up to 75% in volume. Once wet, air-filled vesicles formed due to the rapid sealing effect of overlying smectite in the column. No volume change occurred for illite, mordenite and kaolinite gangues. For kaolinite mixtures acid puddles formed on top of the column during initial leaching due to the delamination and barrier formation of this phyllosilicate. Fluid recovery was <60% for expandable phases and reached up to 80% for non-expandable mixtures. These observations confirm the very low extractions obtained in ore with a combined smectite – kaolinite gangue for Mina Sur. The most important mineralogical changes observed in the solid residues are: reduction of basal smectite phase reflections (XRD), and slight loss of illite intensities. This is also reflected in the major element composition of the residues, which demonstrate a loss of Mg, Mn, Ca, Na, K followed by Fe, Al and Si; with their proportions depending on the starting materials. Furthermore, alunogen and meta-alunogen formed, with related phases coquimbite (illite) and godichite (nontronite) also depending on gangue mineral chemistry. For laumontite samples, meta-alunogen and alunogen precipitated from the leachate."

Jan 1, 2003

By Jan Svoboda, Atsushi Shibayama, Toyohisa Fujita, Toshio Miyazaki, Kenji Murata

"The electrical disintegration (ED) method and disintegration by underwater explosion were investigated as new fragmentation techniques for the kimberlite ore and tungsten scrap of superalloy (carbide bit). The results of various breakage tests demonstrated that both fragmentation methods as new disintegration techniques for recycling were able to liberate various components of materials of different resistivity and elastic impedance.SUMMARYThe breakage of the kimberlite ore from South Africa (sample size: 15 mm x 15 mm x 6 mm) was achieved by the ED method. A relationship between the sample size, voltage, the electrical current and the energy needed for the disintegration was found from the experimental results. Kimberlite exhibited a high degree of breakage, when the high voltage of 60 kV and the pulse current of approximately 5000 A were applied to the sample by the generator during 0.2 microseconds (Fig. 1)."

Jan 1, 2003

By Marlize Barkhuizen, Chris Aldrich

"Owing to environmental constraints, safety considerations and competitive pressures, the development of model-based process control and other automated systems have experienced considerable growth in the last few decades. Reliable process models are usually critical to the successful implementation of these systems. In complex processes, these models are often constructed from process data, as modelling from first principles may not be feasible or cost-effective.Even so, modelling or identification of nonlinear systems from historic plant data can be a daunting task and in the process industries the problem is complicated by the presence of noise from various sources, nonstationarity of the data, intermittence, such as observed in particulate flows, etc. Traditional methods, such as frequency analysis and linear modelling do not handle these systems well. Similar problems arise with the application of nonlinear theory developed over the last few decades, where much of the analysis depends on embedding of the data in a phase or pseudophase space, since these methods were not originally designed to deal with noisy systems.With singular spectrum analysis, the data are embedded in a high-dimensional reconstruction, followed by the introduction of a new coordinate system, where the origin is moved to the centroid of the reconstructed system states and the axes are represented by the dominant principal components of the states (points)."

Jan 1, 2003

By Christopher Davey, Professor Emeritus, Marian Mazurkiewicz, Peter Kanjorski

The concept of a high pressure liquid jet mill with highly unsteady flow, has been developed and recently patented by Cornerstone Technologies LLC (CsT), for the purpose of micron and sub-micron particle production. The mill accepts feed sizes up to 15mm for some materials and is capable of sub-micron production. Successful material range from precious metals such as silver and palladium to dielectric components and substrates such as Barium Titanate slips, zirconia, titania and silica. The process has also succeeded in adequately reducing the size of materials for both composite and coating uses such as anthracite coal, graphite, chrome metal, wollastonite and more than 100 others. A unique design approach has been taken to highly maximize the energy flux in the mill’s chambers to create extremely high turbulence and destructive cavitation. This is assisted by shock waves, which cause particles to undergo ultra high frequency pressure pulsations, high frequency collisions and then abrasion, shattering, hydro-wedging, and cleaving. Due to these extreme properties the processing occurs in just fractions of a second allowing throughputs up to 1000 kg/h on a machine that would fit inside a 60 cm box. The technical solution and technological advance, as well as the environmental and economic benefits indicate rapid and wide spread acceptance of high-pressure liquid jet milling in modern industry.

Jan 1, 2003

By Andrzej Luszczkiewicz, Magdalena Duchnowska, Jan Drzymala

A selected flotation system of beneficiation of the copper ore at KGHM Polska Miedz S.A. has been analyzed in the article. It was found that a proper assessment of upgrading must be based on two elements, that is the upgrading process selectivity and working point of the considered flotation unit, both determined, preferentially by means of the Fuerstenau recovery-recovery upgrading curve. The Cu recovery - non-Cu components recovery upgrading curve was selected for calculations because its background lines (no separation and ideal separation) are insensitive to changes in the grade of feed of the processed material. This approach allows a comparison of upgrading results for feeds having different grade, being upgraded in various flotation machines and under different physicochemical conditions. It was shown in the paper that the main criterion for comparison of two working in parallel systems is selectivity of upgrading. However, when two flotation machines, despite of the same selectivity, produce concentrate and tailing of different grades, it is necessary to analyze their working points using upgrading curves. The proper position of the working point depends on the criterion imposed on the process and is a result of not only basic parameters of the upgrading process such as feed, concentrate and tailing grades but also on economic parameters such as costs associated with the production of concentrates and the time needed for their production.

Jan 1, 2014

By D. B. Sundar Ramam

In the recent past, a paradigm shift in terms of resource utilization and beneficiation practices is experienced by the Indian mining and mineral sector. Depleting iron ore reserves coupled with increasing demand for low-alumina iron ore fines to improve blast furnace performance in terms of productivity and reduced slag rate necessitate intensive beneficiation of iron ore. The task is even difficult for Indian iron ores, which are generally high in iron content and at the same time characterized by aluminous gangue. In 2006, M/s Tata Steel commissioned a state-of-the-art Jigging Plant (Batac Jig) at Noamundi Iron Mine (NIM), mainly to reduce alumina in iron ore fines. The jigging plant is incorporated in the existing beneficiation circuit to treat ?10+0.5mm size fraction of classifier fines. Over the course of plant stabilization while the plant could deliver desired ore upgradation and average product alumina, variability in terms of alumina content has been a concern. This paper discusses a case study of process parameters optimization in jigging operation to achieve consistent product quality while improving the effectiveness of gravity concentration for the beneficiation of Noamundi iron ore also to take care of inferior plant feed (input) grade year on year. The operating variables used to optimize jigging operations include bed height, pulsion and suction time, particle size, strokes, and plant throughput rate.

Sep 1, 2012

By Andries Van Wyk, Steven Bradshaw, Guven Akdogan, Jacques Eksteen, Cornelius Snyders, Cleophace Mpinga

"In order to exploit lower grade and complex platinum group metal resources, cheaper and more efficient alternatives to the conventional mill-float-smelt-refine route are being sought, particularly for resources’ in areas that are water-scarce and where electrification is costly and problematic. Leaching with cyanide is a promising process option and although recoveries are lower than in the conventional process routes, progress into the understanding of cyanide leaching of PGM containing ore and concentrate has been made. Research regarding the feasibility of upgrading the pregnant PGM leach solution using activated carbon has, however, been lacking and hence forms the focus of this paper. Bottle roll adsorption tests for dilute PGM solutions (0.15ppm Pt, 0.38 ppm Pd, 0.1 ppm Au) onto granular activated carbon showed high rates within the first 60 minutes (giving more than 90% recovery of precious metals). Comparison of the Pt isotherm to Au isotherms from literature indicated a similar loading capacity, while that of Pd was found to be significantly lower. The effects of solution pH, temperature, base metal concentration, free cyanide concentration, thiocyanate concentration, initial PGM concentration and activated carbon concentration were investigated and are discussed. Elution of the Pt and Pd, with the AARL elution process, was found to be effective with recoveries of 95% after 5 bed volumes of eluant at the optimum pre-treatment concentrations and a temperature of 80°C. Temperature, NaCN and NaOH pre-treatment concentration and the ionic strength of the eluant were found to be the most important factors affecting elution while base metals concentration, acid-pre-treatment, carbon loading and thiocyanate concentrations to a lesser extent. Simplified combined flow sheets are suggested and the corresponding mass balances are compared."

Jan 1, 2014

By P. Somasundaran

Gangue minerals can often have severe adverse effects on selective value mineral separation. Such effects can be mediated through a variety of pathways or mechanisms. One popular mechanism is that of ?slime coating? or heterocoagulation, wherein the gangue mineral fines are believed to coat the value mineral surfaces and thereby reduce selectivity and floatability. Another pathway that has received relatively little attention is that mediated through the effect of gangue minerals on pulp rheology, and consequently selective separation. Our recent work in developing a scientific understanding of these effects has highlighted the prevalence and importance of this pathway. In this study, the impact of shape and morphology of serpentine gangue minerals on suspension rheology and selective Ni flotation from ultramafic ores was investigated. We found strong evidence for micro- and macro-network formation in the presence of acicular (needle-shaped) or fibrous minerals, which impacted pulp rheological properties. Results also supported the hypothesis that morphology has a greater role to play than mere shape. The size of the network ranged from 5 microns to 2 cm depending upon the amount and aspect ratio of fibrous minerals. These networks impede many flotation sub-processes, such as gas dispersion and bubble-particle interactions. Additionally, the small pore size of the networks prevents bubble penetration leading to a large transport of the gangue minerals to the concentrate via lifting of the entire network by bubble flux, which resulted in a significant grade dilution. Based on the scientific insights generated in this study various techniques have been developed to improve selective value mineral separation. Keywords: fibers, aspect ratio, microstructures, networks, pulp viscosity, gangue transport

Sep 1, 2012

By Tomasz Niedoba

Coals occurring in nature are characterized by various properties. According to Polish norms, the classification of coals taking into consideration their calorific value contains coals from type 31 (flaming coal) until type 43 (meta-anthracite). The samples of coal of type 31 were taken for investigation. To this purpose, the approximations of ash contents and density distribution functions were done for this coal type (determination of marginal distribution functions). They were the basis for application of so-called Morgenstern distribution functions to approximate the function Z=L (?), where Z is ash contents and ? - coal density. Then, the comparison between obtained results was performed and the results were statistically evaluated. They are the basis for the further research of other types of coals.

Sep 1, 2012

By K. Hori

In this study, the determination of optimal conditions for jig separation has been investigated with a TACUB jig separator. The TACUB jig, from which a Batac jig originated, is a useful gravity separator that is effective to separate crushed solid wastes as well as coarse ores. A mixture of crushed polyethylene (specific gravity 1.3) and polyvinyl chloride (specific gravity 1.5) was separated by a batch TACUB jig by varying the frequency (wavelength) and the amplitude (pulse stroke length). It was found that the sample particle layer in the separation chamber was fluidized without turbulence by the rising water pulse resulting in the separation. However, a too strong water pulse reduced the efficiency of the separation of the particles. The results indicate that the specific velocity of the rising water is necessary to fluidize the particle layer without turbulence to separate the particles. The expansion ratios of the thickness of the particle layer in rising flows were measured in a cylindrical column. The pressure losses by the particle layer were calculated from the expansion ratios and the velocity of the rising flows by Ergun?s equation. The curve of the pressure loss vs. the velocity of rising flow showed a maximum point corresponded to the point of fluidization. The velocity of a rising flow on the point of fluidization provided the optimal separation condition.

Jan 1, 2014

By Anatoly F. Usov, Vyacheslav A. Tsukerman

"The Russian scientists have developed a new energy saving method for an efficient destruction of the sturdy and hard materials (rocks, ores, frozen soils, concrete blocks ets.) - the Electric Pulse Discharge method of materials destruction (EPD). The detailed researches of a broad circle of problems connected to development EPD-disintegration of materials of a various nature and area of use are executed. The electrical and power characteristics of process, physical fundamentals of selectivity of a breakdown and destruction are investigated, the means of electric pulse splitting and refinements of materials are developed, the technological efficiency of disintegration of industrial minerals estimated.One of the most important characteristics of the EPD-disintegration of ores is the high selectivity of destruction, which provides a large ratio of useful minerals' grains opening, and at the same time, it destroy them less. This ensures in the subsequent stages of beneficiation of ores considerable increase of the extraction and improving the quality of concentrates.The technological tests of various industrial minerals have shown a possibility the EPD-disintegration, as a process that provides the best efficiency of disclosure of useful minerals in all types of ores. Technological and economic efficiency of the method of ore beneficiation is the highest for difficult beneficiated ores with rather low extraction by existing methods. The increase of extraction in this case can reach several percents. As a rule, at a EPD-disintegration the disclosure of mineral grains happens in earlier stages of material comminution than at a mechanical comminution, and with less damage of products. This promotes a simplifying the process of ore preparation and for reducing the power consumption."

Jan 1, 2003

By I. Zh. Bunin, G. K. Khachatryan, N. E. Anashkina

For optimization of diamond processing technology the influence of nanosecond high voltage pulses on mechanical and technological properties of diamond crystals and kimberlite rock-forming minerals (calcite, olivine, serpentine) was investigated. Using methods of Fourier Transform Infrared Spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), microscopy and mikrohardness measurement the changes of structural, physic-chemical surface properties, and microhardness of minerals as the result of impacts, was studied. Non-thermal impacts caused a decrease of kimberlite rock-forming minerals microhardness in general to 40-66% as the result of surface microstructure destruction which is caused by formation of micro cracks, traces of surface breakdown and other defects. At the same time, the pulse energy impact on natural diamonds led to formation of B2 type crystal lattice microsift defects, elevated concentration of which increases the hardness properties of crystals. The obtained result indicates possibility of applying pulsed energy effects to improve the softening efficiency of diamond-bearing kimberlites rock-forming minerals without damaging the diamond crystals and ensuring their preservation by the subsequent grinding of ores. By IR and X-ray photoelectron spectroscopy revealed that processing by hight voltage pulses causes a change of natural and synthetic diamonds surface functional cover composition. Short-term exposure (~ 10 - 30) leads to detachment and partial destruction of secondary phases mineral films on the surface of natural technical diamonds, increasing floatability and hydrophobicity of crystals. However, with increasing duration of treatment (~ 30 - 150) occurs surface hydroxylation (found by XPS for synthetic diamonds), as a result of diamond surface layer oxidation. The effect of increasing the natural diamonds flotation activity by 14% (from 47% to 61%) was experimentally established as a result of processing diamond crystals with nanosecond pulses (~ 10-50 sec), which indicates the principal possibility of using pulsed energy impacts to intensify the diamond flotation during processing diamond-bearing kimberlites.

Jan 1, 2018

By Zhaohui Qiu, Yaguan Ji, Hong Zhong, Qingxia Liu, Yada Liu

"Water is a necessary process medium in mineral processing. For the operations where fresh water is not available, sea water could be used as an alternative processing medium to replace the fresh water if we would have built a solid understanding of the interfacial science and flotation chemistry of sulfide minerals in sea water. In this research, micro flotation of chalcopyrite and pyrite in deionized water and sea water were investigated. For chalcopyrite, the recovery starts to drop from pH 10 in deionized water and from pH 9 in sea water, and the flotation recovery close to 100% before it drops. We can found from the results that chalcopyrite flotation is depressed much at pH 11 in sea water when much white precipitate is found. For pyrite, the flotaion recovery changs a lot in deionized water with 1*10-5 M potasium amyl xanthate (PAX) as collector. It’s relatively high at pH 8~10 compared with that at pH<8 and pH>10. While in sea water, the trend is almost the same as that of chalcopyrite. Zeta potential measurements and chemical equilibrium calculation were used to find out that magnesium hydroxide species coats on the surfaces at high pH in sea water are the main reason for depressing the chalcopyrite and pyrite flotation. Through understanding the interfacial science and the solution chemistry of sea water and its impact on processing efficiency, this research will not only helps reduce the use of fresh water to minimize the disposal of spent water for environment protection, but also enhance the recovery of valuable minerals in froth flotation."

Jan 1, 2014

By M. Amani, A. Akbarinasab, M. Bazmandeh

The fourth iron ore production plant at Golgohar mining and industrial company consists a ball mill and wet medium intensity magnetic separators (3500 Guss). The ball mill product applies directly into MIMS and the MIMS concentrate directly transfers to the low intensity magnet separators (LIMS). The thickener is used for dewatering of MIMS and LIMS tailings. By sampling from streams of ball mill and separators, it was defined that the grade and iron recovery were 60% and 80% respectively while they would be 66% and 90% respectively based on the designing documentation. The average of P80 in the ball mill was 342 micron in a month that is coarser than optimized value. This problem was related to unsuitable operation of grinding. For optimization of grinding efficiency, the amount of charge volume was investigated as a variable. The measurements illustrated 32% charge volume. For increasing grinding efficiency, the charge volume was increased 1% and 1.6% in two stages. The results showed ball mill power draw average reached from 3650 kw to 4120 kw and the average P80 reached to 329 micron. All of parameters calculated about 35 day before and after change. Average of Ball mill feed iron ore grade before and after change was 49.24% and 50.32% respectively. This change caused an increase in efficiency of MIMS, where the enrichment ratio and concentrate grade increased 2% and 1.9% respectively. For increasing the iron grade of the MIMS concentrate; the orifice of the tail flow exit pipe changed from 4 inch to 6 inch and the concentrate grade increased 2%.

Jan 1, 2014

Geopolymers are novel engineering materials with the potential to play a highly significant role in the transformation of the construction materials and building products industry in the push to-wards sustainable development. These materials are formed by activation of industrial aluminosilicate waste materials such as coal ash or blast furnace slag with alkaline solutions. Some mineral waste can also be used, either as fillers or as reactive components. The use of waste-based geopolymers results in significant (up to 90%) reduction in carbon dioxide emissions when used in cement replacement applications. In addition to the formation of conventional pre-cast products, these high performance mineral binders are ideally suited to use in the conversion or encapsulation of toxic waste, including radioactive waste, due to their chemical stability and resistance to acid attack. It is the aim of this paper to review recent developments on the science underpinning this ?green? technology, and to discuss the technical and commercial drivers governing the large-scale adoption of the technology. Some of the recent fundamental breakthroughs in the study of geopolymer technology at the University of Melbourne will be presented. Despite the complexity of this reactive sol-id-gel system, progress has been made in the development of a thermochemical reaction kinetic model that has been validated using both calorimetric data and synchrotron kinetic data. Geopolymerization is potentially a disruptive technology, so that it is normal to expect strong resistance from established companies in the construction materials industry. It is increasingly necessary that waste generating industries such as mining collaborate with industries such as construction that could utilize this waste. The world?s first full scale geopolymer plant utilizing waste and re-cycled material has been commissioned recently in Melbourne, Australia, so progress on commercialization will also be presented. The authors frequently present keynote lectures on geopolymer science and technology at materials science, ceramics and construction materials conferences. However, this interdisciplinary technology that is still in its infancy, deserves more attention in the mineral processing and mining industry in view of its potential use in the mining industry, and also in view of the importance of mineral processing techniques in recent advances in geopolymers.

Jan 1, 2014

By André Mans, Frans B. Waanders

"Ferrosilicon (Fe-Si) is an important commercial material and it forms the basis of the powder used in dense medium separation (DMS) of various minerals in a minerals beneficiation process. Current losses of Ferrosilicon (Fe-Si), which is used in the dense medium separation (DMS) of iron ore at Kumba Resources, Sishen, South Africa occur due to adhesion to the separation products and also by being present in the effluent stream, due to abrasion. The losses contribute greatly to the running cost of the plant and the purpose of this project was to determine the characteristics of the unused Fe-Si and then to characterise the changes that occur during storage and the use thereof.A Scanning Electron Microscope (SEM) and Mössbauer Spectroscopy (MS) were used to investigate the characteristics of the fresh and used Fe-Si. The SEM analyses of the Fe-Si yielded a composition of 15 wt.% Si and 85 wt.% Fe with minor impurities of Mn and Cr (<1 wt. %), resulting in an ordered phase with a calculated composition of Fe2Si. The average density of the Fe-Si was found to be 7.177 g.cm-3 whilst the size distribution was determined with the d50 of the particles being approximately 30 µm. A slurry, containing 10% solids was prepared, which had a density of about 1.1 g.cm-3 and this slurry was used to conduct the various experiments under laboratory conditions at the university. Samples were taken at regular intervals from a storage container containing a lime solution as well as from a closed circulation circuit system, kept at a constant temperature of about 60°C. Mössbauer Spectroscopy yielded, for the new fresh Fe-Si-samples, a two-sextet spectrum with hyperfine magnetic field strengths of 19.9T and 30.7T respectively, and the yellow-brown froth was found to be akaganeite or ß-FeOOH.It was found that the biggest loss of Fe-Si was due to the abrasion of the particles during the DMS process. A possible change in magnetic properties was also observed, leading to further losses that could occur during prolonged use of the medium. No clear changes to the Fe-Si occurred during correct storage methods, as was initially thought."

Jan 1, 2003

By Xiaodong Jia, Richard A. Williams

"The packing of particles is a fundamental property of a material or system made up of particulates because it underlies many other physical properties of that material or system. Despite being ubiquitous, particle packing has not been an easy subject to study either experimentally or theoretically, except for a few regular shapes.This paper describes the recent developments, arising from research at Leeds, in the computer modelling of packing of complex shaped particles and prediction of physical properties of the structures represented by the packing. The computer model DigiPac, is capable of packing particles of any shapes and sizes in a container of arbitrary geometry. Figure 1 shows a few examples that are relevant to the mining and mineral industry.The ability to predict packing structure of real particle shapes and to compute directly some structuredependent physical properties (such as liquid permeability, mechanical strength/stability, compaction and sintering, dissolution and leaching, etc.) is obviously highly desirable and has significant potential in industrial applications. Examples are presented relating to the packing of granular materials.The mining and mineral engineering industries are well placed to exploit this advance in digital packing and simulation since they deal primarily with asymmetric and complex particulate mixtures. In the future we expect to see a number of developments in this area including:Algorithms that can optimise packing to achieve user-defined propertiesA more rational approach to determining flowability of complex powdersUse of these more realistic packing algorithms linked to blast and crusher design"

Jan 1, 2003

By Ronel du Plessis, John C. Davidtz, Jan D. Miller

Xanthates (dithiocarbonates) have been the collector of choice for the flotation of sulfide minerals ever since the flotation process was developed and have been studied quite extensively. Recently, trithiocarbonates have been shown to be very effective in bulk sulfide bench-scale flotation. Fundamental analysis using electrochemical techniques have supported these bench-scale results, illustrating that the trithiocarbonate (TTC) collectors are more readily oxidized to their corresponding dithiolates, than the dithiocarbonate (DTC) collectors, as is shown in Figure 1.

Jan 1, 2003