Search Documents

By Graeme Heyes, Warren J. Bruckard, Michael A. Somerville

"Over the past few years CSIRO Minerals has been conducting research aimed at developing a continuous copper converting process to replace the traditional two-stage batch process that is currently used to produce blister copper. Sirosmelt type reactors and calcium-ferrite (lime-based) slags have been used rather than the conventional iron silicate slags. The research work has now been extended to focus on the development of a single-stage continuous copper making process (so-called direct copper converting) in which copper concentrates are converted to low-sulfur blister copper in a single step, that is the smelting and converting steps occur in one continuous stage.One feature of the direct copper converting process is that copper losses to the slag phase can be high, meaning the slag produced needs to be treated to recover the copper value. The feasibility of the whole copper making process will most likely depend on the efficiency and cost effectiveness of the copper recovery stage. Flotation has been identified as the most economical option to recover the copper from direct copper converting slags where it has been estimated that a copper recovery from the slag of above 90% is required to make the overall single stage copper making process economically feasible.A limited series of laboratory batch flotation tests was conducted on a suite of calcium-ferrite-based slags made in laboratory smelting trials. Copper sulfide concentrates from MIM were used as feed-stocks. The objectives of this work were to develop a robust flotation process to maximise the copper recovery and iron rejection from slags made in the process, and to establish operating conditions for future continuous flotation pilot plant trials.The slags treated included a reduced low copper slag, an oxidised high copper slag composite, and a very reduced low copper self-pulverising slag. The copper content of the slags varied from 2.9% to 14% Cu and the CaO/Fe ratio varied between 0.30 and 0.54. In general, the higher the copper content the more oxidised the slag. The copper was present as metallic copper, oxide copper and copper-calcium ferrite phases with the phase mix related to smelting conditions. The slags were crushed, ground, wet-screened at 355 or 210 µm to remove coarse metallic particles of copper, and floated at natural pH (about pH 11) using reagents and conditions appropriate for the selective recovery of the copper phases. Reagent additions were typically 200 g/t KEX and 500 g/t Na2S.9H2O and the grind size was generally a P80 of about 40 µm."

Jan 1, 2003

By T. Ueda, T. Oki, S. Koyanaka

"Accurate assessment of the liberation state of crushed ore particles is important for efficient mineral processing. In general, the liberation state is assessed by two-dimensional (2D) measurement of polished ore sample sections. However, this 2D measurement inevitably suffers from overestimation of the degree of liberation, known as stereological bias. This arises from the fact that biphase particle sections of which only one phase happens to have been cut are indistinguishable from liberated particles. To date, several stereological correction methods have been proposed, but their applicability for various types of particles has not yet been sufficiently examined, and this tends to undermine their practicality. We have addressed this problem using a numerical-analytical approach in which various types of biphase particles are modeled, and the 2D sectional information is compared with actual three-dimensional (3D) information. Through simulations, we revealed a general relationship between the internal mineral structure of particles and the stereological bias. Finally, we have developed a unique stereological correction method in which the texture (a 2D pattern characteristic) of particle sections is used to estimate the internal structure of particles, and thereby the stereological bias. KEYWORDS Mineral liberation, stereological bias, texture analysis INTRODUCTION Mineral liberation assessment of 2D particle sections inevitably suffers from stereological bias; that is, overestimation of the degree of liberation. Stereological bias is caused by the fact that a composite particle can be misidentified as a liberated particle when only one phase happens to have been cut in sectional measurement. Stereological bias has attracted attention since Gaudin pointed out its importance in 1939 (Gaudin, 1939). Several attempts have been made to measure the 3D liberation state directly, avoiding the bias, using X-ray computed tomography (Gay and Morrison, 2006; Lin and Miller, 1996; Miller et al., 2003; Miller et al., 2009; Reyes et al., 2017; Videla et al., 2007). These have provided useful information through laboratory testing, but further technical refinement is necessary for practical usage, to overcome the technique’s limitations in terms of resolution, assessment of minerals of similar density, and speed. Therefore, for practical purposes, detailed information regarding mineral phase geometry is obtained by sectional analysis, using automated scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDX)-based analysis (e.g., with a mineral liberation analyzer (MLA) (Fandrich et al., 2007; Sandmann, 2015)); and the development of an effective method of stereological correction, which predicts the relevant bias and transforms the measurable 2D degree of liberation into its 3D counterpart, is an important research aim."

Jan 1, 2018

By Xingshi Yang, Ghislain Bournival, Seher Ata

"Particle-laden interfaces are a fundamental research topic in froth flotation since the process involves particle-coated bubbles in both the pulp and the froth phase. In most experimental studies the characteristics of the particle layer in multi-bubble systems are poorly defined. An experimental setup has been developed based on a Langmuir-Blodgett (L-B) trough. The modified trough allowed introducing an air bubble beneath the particle monolayer formed at the air-water interface which made the study of the interaction between the bubble and the monolayer under various pH values possible. The monolayer characteristics of the particles were also studied and compared in terms of surface pressure (?-A) isotherms and packing factor. On compression, the particles formed branched structure at high pH whereas a uniform monolayer was formed at lower pH. Observations related to the behavior of particles during compression and expansion cycles, and the coalescence of a bare bubble with the flat particle laden interface were provided and the implication of the results for flotation process was discussed.INTRODUCTIONFroth flotation is known for its versatility and ability to concentrate low-grade, complex ores. It is considered a physico-chemical process in which particles attach to air bubbles, depending on their hydrophobicity as well as other factors, and are carried to the surface to form a froth layer. Reagents are used to stabilize bubbles and the froth layer (Pugh, 1996). However, particles, which are carried by the bubbles or entrained, significantly contribute to the stability of the froth phase (Ata et al., 2003; Zanin et al., 2009; Bournival et al., 2015a). Their relevance in mineral processing has led to a number of fundamental studies on the effect of particles and their properties on the process of froth flotation.Flotation systems are particularly difficult to characterize due to the broad range of properties of particles (e.g. size, liberation, hydrophobicity, etc.) and inconsistent operational conditions (e.g. changes in water quality, reagent addition, etc.). Several studies have made the use of well characterized particles in laboratory conditions. Such studies allowed the finding of an optimal contact angle for the stabilization of the froth phase (Johansson and Pugh, 1992; Ata et al., 2002). Froths have a large number of bubbles so that individual interactions are not observed. The study of two bubbles allows to determine the stability of the bubbles, with particles, and to some extend the stability of the bubble-particle aggregate (Gourram-Badri et al., 1997; Bournival et al., 2015b). The removing of particles between two bubbles may also be studied from a Scheludko cell (Johansson and Pugh, 1992) or by observing a bubble with a flat interface (Sethumadhavan et al., 2002). However, these systems provide limited information on the arrangement of the particles."

Jan 1, 2018

By M. A. Hampton

The surface oxidation of sulfide minerals in aqueous solutions is an important sub-process in sulfide flotation and hydrometallurgy, but a full understanding of the oxidation process and products is still lacking. Many oxidation pathways and products involving elemental sulfur, metal polysulfide, metal-deficient sulfide and sulfate have been proposed, confirmed and argued. In this paper we provide further insight into the surface electrochemical behaviour of galena in aqueous solutions. For this research we have developed a novel experimental system, that combines chronoamperometry and AC-mode AFM surface imaging, which allows for in-situ, synchronized electrochemical control and examination of oxidative surface morphology. At pH4, the morphology of elemental sulfur (detected by ex-situ Cryo-XPS) formed on the oxidizing galena surface depends on the electrochemical potential pathway. In multi-step chronoamperometry (i.e. four potential steps from 0 mV to + 350 mV) the sulfur forms as nanoscopic domains, whereas in single-step chronoamperometry (i.e. one potential step from 0 mV to + 350 mV) sulfur forms as a heterogeneous layer. In each case the oxidation is controlled so that the number of electrons (coulombs) passed per unit area is the same, therefore the amount of sulfur produced is also the same. The differences in morphology with electrochemical potential pathway are explained using a nucleation and growth model. The formation of sulfur on the surface increased both advancing and receding contact angle of galena, but the morphological changes induced by different electrochemical potential pathways did not significantly alter the hydrophobicity of the surface. Keywords: galena, lead sulfide, oxidation, Atomic Force Microscopy, electrochemistry, collectorless flotation, hydrophobic

Sep 1, 2012

By A. Collings, A. Farmer

Power ultrasound may be used in the processing of mineral suspensions to clean the particle surfaces of oxidation products and fine coatings, mainly through the large, but very localised forces, produced by cavitation. This effect may be utilised in lowering the level of iron contamination in silica sand used for glass making, in improving the sharpness of electrostatic separation of heavy mineral concentrates, in shortening the time of leaching of minerals and in improving the selectivity and recovery of flotation processes. Parameters affecting the efficiency of these processes, such as input power and levels of reagent addition, are discussed. In particular, we present data showing the relationship between power input and the particle size of surface coatings removed, which can be explained by the Derjaguin approximation for the energy of interaction between a sphere and a flat surface. Pilot scale studies, using commercially available components, are currently being used to assess process viability and will be compared with laboratory scale results.

Jan 1, 2003

By Hideki Yamamoto, Norihiro Murayama, Junji Shibata

"Hydrothermal syntheses of zeolite from coal fly ash were carried out by using various alkali sources. NaOH, Na2CO3, KOH, K2CO3 and their mixture were applied for an alkali source of zeolite synthesis. The various physical properties of the reaction product, such as the kind of zeolite crystal, cation exchange property, surface texture and so on, was investigated through the zeolitization reaction from fly ash. The mechanism of zeolitization reaction was considered from these results.Zeolite P(NaP), hydroxysodalite(HS) and chabazite(K-CHA) are synthesized as zeolite species, when fly ash hydrothermally reacts in various alkali solutions at 393K. The crystal structure of the products obtained in NaOH solutions for 3h changes from NaP to HS with increasing NaOH concentration. K-CHA formation in KOH solutions needs 10h of reaction time, which is longer than that of NaP or HS.Dissolution, condensation and crystallization steps exist in the zeolitization reaction from fly ash, and the particle surface of products remarkably changes in each step. The fly ash is spherical particles and the surface is smooth(Fig.1(a)). The dissolution of fly ash occurs in the heating process until 393K, and the particle surface changes like unevenness(Fig.1(b)). In case of NaP, the condensation of aluminosilicate ions takes place at 373-393K, and the amorphous aluminosilicate is deposit on the unreacted fly ash(Fig.1(c)). The crystallization of NaP already begins to occur at 393K and the surface is covered with fine zeolite crystals for 24h(Fig.1(d))."

Jan 1, 2003

By A. Otsuki

This paper describes the evaluation method of dispersion and coagulation of silica nano-particles by means of interactive force apparatus. The apparatus measures the size of fine particles in aqueous solution or organic solvent of high concentration and/or low optical transparency. Other conventional apparatus for size measurements (such as, apparatus utilizing dynamic light scattering) are difficult to measure the size of particles in such conditions accurately, due to multi-scattering of light in the sample solution or solvent. The apparatus measures the interactive force between two surfaces, i.e. the gold-coated glass hemisphere and the brass flat plate, (which is fixed at the bottom of the sample cell). The apparatus has three parts, i.e. main part (which consists of electric balance, hemisphere and flat plate), control part (i.e. personal computer, piezo-stage controller and voltage supplier), and detecting part (i.e. multi-meter and oscilloscope). During the measurement, electric field is applied between the hemisphere and flat plate, and thus dielectric particles are arranged toward the direction of electric field in the area between two plates. When the two plates are close to each other, two different forces (i.e. repulsive force and attractive force) will alternately act on particles due to the structure change of the particles. The repulsive force occurs when the structure of particles is stretched by compressive force; whereas the attractive force occurs when the aggregate structure is broken. The cycle of the repulsive and attractive forces is a primary size of particle or size of aggregate, which depends on the degree of agglomeration. The measured size of particles, which is varied depending on their degree of dispersion and coagulation, determined the characteristics of the silica particles. In this research work, the effect of size and concentration of particles in aqueous solution on the degree of dispersion and coagulation of the silica particles were investigated. Spherical silica particles were selected for this investigation due to their variety of size. This apparatus can be used to evaluate the degree of dispersion and coagulation of other nano-particles in various solvents in many process industries.

Jan 1, 2014

By Sashnee Raja, Mehdi Nemati, Ashley Sissing, Susan T. L. Harrison

"Extreme thermophiles, operating at 65 - 90°C, are finding increasing application in biohydrometallurgy. These micro-organisms have the advantage of exhibiting better oxidation kinetics in terms of reaction rate and extent of mineral solubilisation (Duarte et al., 1993; Norris and Barr, 1988; Konishi et al., 1995). These extreme thermophilic Archae, characterised by a different cell envelope structure (König and Stetter 1986, König 1988, Michel et al. 1980) perceived to provide reduced structural strength in comparison to bacterial envelopes, and customised metabolic pathwaysThe active tank bioleaching process, used for high rate leaching, is conducted in a slurry bioreactor. Here sufficient energy dissipation is required to ensure suspension of the mineral phase as well as to sustain high rates of gas liquid mass transfer. It is well known that subjection to hydrodynamic stress of sufficient magnitude may alter the physiological state of a range of micro-organisms through changed viability (ability of the microbes to grow), metabolic activity and integrity. While limited study on the influence of the solids phase on thermophilic leaching performance is reported, initial reports suggest that the thermophiles used for bio-oxidation appear to be sensitive to hydrodynamic conditions (Jordan et al 1993, Clark and Norris, 1996) and the presence of solids (Norris and Bar 1988, Le Roux and Wakerley, 1988, Escobar et al. 1993, Torres et al. 1995, Nemati and Harrison, 2000)."

Jan 1, 2003

By A. Boulton

Low molecular weight synthetic polymers substituted with hydroxyl, carboxyl or sulfonate functional groups were used to improve the flotation separation of zinc or copper sulfide minerals from iron sulfide gangue minerals in three massive sulfide ores of different mineral composition. These polymers produced significant improvements in zinc or copper grades as a result of a selective depression of iron sulfide minerals. These results are significant considering the differences in ore type, proportion and type of iron sulfide minerals present, and grinding medium used in this study.

Jan 1, 2003

By Cristian Melipichun, Leopoldo Gutierrez

The effect of the presence of fine particles of kaolinite and montmorillonite on the induction time for attachment of bubbles to particles of a copper concentrate rich in chalcopyrite was evaluated in this study. The results obtained from induction time measurements were correlated with data of concentrate recovery achieved from micro-flotation experiments. The effect of the presence of fine clays on the stability of air-water foams was also studied through measurements of the foam volume generated in a glass column under different conditions of air flowrate and MIBC concentrations. The experimental results showed that induction time values increased under the presence of fine clays. These data agreed with results obtained from micro-flotation experiments that showed that copper concentrate recovery decreased when clay particles were added. Although a complete explanation for these results is not available, the fact that experimental observations indicated that fine clay particles tend to adsorb on gas bubbles, suggests that the interactions between fine phyllosilicate particles and air bubbles have to be taken into account when studying the effect of clays on froth flotation. Foamability tests showed that the presence of fine clay particles increased the foam volumes only at high additions of clays and low dosages of MIBC. The results obtained at higher dosages of MIBC showed that the foam volumes decreased with the addition of clays under all the experimental conditions tested.

Jan 1, 2014

By Chris J. Martin, Nichola A. McKay

"In mid-2001, North American Palladium commissioned a new 15,000 tonnes per day milling and flotation circuit at their Lac des Iles Mine (LDI), one of only two primary platinum group element (PGE) producers in North America. The mill treats an ore containing 2.3 g/t PGE producing a concentrate assaying 300 g/t PGE, at a recovery of roughly 75%.Top-size control crushing is conducted ahead of semi-autogenous milling. A portion of the SABC circuit feed is crushed to –25mm to increase mill throughput. Product from the SABC circuit is fed to flotation. Flotation consists of roughing and scavenging, with the rougher and scavenger concentrates each being reground using vertimills. Cleaner flotation uses two stages of cleaning using mechanical cells, and a third stage using flotation columns, the column tails being scavenged using a bank of mechanical cells. Rougher concentrate by-passes the first cleaner circuit. Reagents added include amyl xanthate collector, dithiophosphate promoter, MIBC frother and a carboxy methyl cellulose-based gangue depressant.SGS Lakefield Research, together with staff at LDI initiated a structured plant optimisation program comprising on-site testing, bench-scale flotation and mineralogical analysis using QemSCAN. The objectives of the mineralogical studies were 1) to identify feed PGM, their size distribution and mineral associations, 2) establish relationships between the PGM mineralogy and PGM floatability, and 3) characterize the culprit silicate minerals diluting the final concentrate.PGM flotation response at Lac des Iles is clearly bi-modal in nature, with about 60% of the PGM floating quickly, to a high value rougher concentrate. The mineralogical work was able to explain the causes of the bi-modal PGM floatability, which in turn created new opportunities for the metallurgists to optimise the circuit."

Jan 1, 2003

By Andrey V. Tarasov

"An environmentally clean and virtually waste-less technology for treatment of domestic and industrial solid waste (HGIW) including other toxic chloride-containing materials has been developed and proven on a full scale by the Gintsvetmet Institute in cooperation with some other Russian organizations.The essence of the process is that the HGIW are decomposing in the liquid base in air-bed slag melted layer under the temperature of 1350-1400°C.HGIW is considered as fuel heat-producing energy of 1500-1800 kCal/kg with 51,7%.Processing of municipal and industrial solid waste in molten slag is carried out autogenously without additional fuel, the blowing is enriched by oxygen up to 50-70%.The complex makes it possible to treat the furnace charge without preliminary drying and sorting with big differences in chemical and morphological composition due to the versatile firing chamber.The proposed process resolves the acute and globally significant problem of dioxin formation.The purpose of the proposed technology is to ensure such destruction of the structural lattice that would guarantee irreversible transformation of the resultant substances to prevent formation of dioxins. It was established the required preconditions to achieve this purpose."

Jan 1, 2003

By Stuart Simpson

The biggest environmental challenge in mining is the management of mine tailings. Deep----sea tailings placement (DTSP) is practiced where the environmental impacts are predicted to be less than the impacts of tailings storage facilities on land. However, DSTP is often highly controversial owing to the challenges in assessing the impacts in deep water environments and potential long----term impacts beyond the proposed tailings footprint. It is well recognized that total contaminant concentrations are often poor predictors of the risk posed by contaminants in sediments. Metals within tailings are mostly present in highly mineralised forms that are typically much less bioavailable to organisms when compared to other common anthropogenic metals. Thus while metal concentrations in tailings can often appear alarmingly high, when compared to sediment quality guidelines (SQGs) used for assessing common urban and industrial impacts, the bioavailability is typically low. Although now well----embedded within risk----based sediment quality assessment frameworks, contaminant bioavailability is still often overlooked in the management of contaminated sediments. In this presentation, we assess and demonstrate the low bioavailability and chronic ecotoxicology of mineral----rich tailings to two benthic invertebrates, recognized for their sensitivity to metals: impairment of reproduction of the amphipod, Melita plumulosa, and the harpacticoid copepod, Nitocra spinipes. We demonstrate that the metal exposure from mine tailings is low when total concentrations are considered, and that the dose to the organism and toxic response observed is highly dependent on contaminant bioavailability. We discuss a range of approaches for the effective incorporation of metal bioavailability when applying SQGs or setting site-specific management limits for mine tailings in marine environments. While proposed DSTP operations require a high level of environmental scrutiny and monitoring during operation and post-closure, environmentally sustainable operations may be achieved when the bioavailable forms of metals within tailings remain below suitable management limits.

Jan 1, 2014

By R. Els Ellis

Enhanced granulation of UASB granules was tested on pilot scale with two different test reactors (about 5 litres capacity each). Sludge from a local sewage works was used, with peach cannery effluent as carbon source. Cyclic motion of the reactor contents, and a daily replenishment of feed material create the necessary stress conditions for enhanced growth. Sizable granules, bigger than 0.5 mm, were produced within 20 days. Of the two reactors tested, the reactor equipped with a horizontal agitation shaft proved more effective.

Jan 1, 2003

By T. Mütze

The progress in comminution is often described by the specific surface area and the energy utilization or the brakeage ratio and breakage function. The principal mechanisms of size reduction are therefore, well known. All four parameters share a common disadvantage: They are limited in describing the behavior of a feed material with fine particles and a wide particle size distribution. An alternative is to describe the progress in comminution with ? The particle size distributions Q(x) before and after the stress or ? The particle concentration ratio pcr(x), which combines these two states. In the case of a self-similar fracture behavior, (in short: self-similarity) the progress in comminution can be simplistically described by the relationship between a reference particle size and the stress intensity. Self-similarity means self-similar breakage functions of geometrically similar particles of the same strength, a certain stress situation and stresses up to the breakage point. Self-similar breakage functions show the same curve at different stress intensities when the fragment size x is normalized with a reference particle size xNorm. This behavior was demonstrated for single particle comminution repeatedly and unequivocally. In the field of particle bed comminution, these results differ in literature. Therefore, the self-similarity in particle bed comminution was systematically investigated at the Institute of Mechanical Process Engineering and Mineral Processing of the TU Bergakademie Freiberg as part of a research project. Limestone, quartz, silicon carbide and glass beads, were examined with a hydraulic press. The particle sizes covered monodisperse fractions in the range of 1-1000 µm, bimodal mixtures of these fractions and polydisperse fractions. The results obviously show that there is no self-similar fracture behavior in the case of glass beads, quartz and silicon carbide. Statements on the self-similarity of limestone are much more difficult: Only some of the investigated limestone fractions show a similar clear, non-self-similar behavior. Self-similar curves appear particularly for fine monodisperse fractions as well as bimodal mixtures, which stressed with pressures above 200 MPa. Considering the measurement accuracy of particle size analysis the coincidence of the curves can be explained by the fact that progress in comminution almost ends above 200 MPa. At this point, a hydrostatic stress state is reached in the particle bed which is known from the literature. This stress state inhibits further fractures. Overall, it has been verified for the investigated materials that there?s no self-similar fracture behavior in particle bed comminution. One reason for the diverse opinions in literature is that there are three types of particles after the comminution in the particle bed: ? Particles which are stressed below their breaking point, ? Particles which are stressed right up to the break point, and ? Particles which are stressed beyond their breaking point.

Sep 1, 2012

By Di Liu, Yongjun Peng

"It was identified that clay minerals adversely affect fine coal flotation through slime coatings. In the study, it was interesting to find that an anionic polymer dispersant, lignosulfonate, successfully mitigated the negative effect of clay minerals in coal flotation using fresh water, but in saline water, it exacerbated coal flotation.In order to understand the mechanisms underpinning the different behaviour of lignosulfonate in coal flotation using fresh and saline water, the adsorption isotherm, and dynamic light scattering (DLS) measurements were conducted in this study. While DLS monitored the molecular conformation change (swelling or shrinking) of the polymer in fresh and saline water, adsorption isotherms enabled polymer adsorbed amount on clay and coal mineral surfaces to be determined. It was found that lignosulfonate adsorbed on the coal and clay mineral surfaces providing effective electrostatic repulsions and resulting in a mitigation of clay minerals from coal surfaces in deionised water. In the presence of saline water, however, polymer molecular conformation changed. Polymer molecules were compressed and adsorbed in form of aggregates. The adsorption amount of lignosulfonate on clay minerals increased in saline water. A low dosage of lignosulfonate could not provide sufficient electrosteric repulsion to disperse clay minerals. Moreover, the high adsorption amount of the polymer on coal and clay surfaces led to a more hydrophilic coal surface, and coal flotation was therefore depressed in saline water. This study provides a new insight into understanding the role of anionic polymeric dispersants in mineral flotation using different quality water."

Jan 1, 2014

By R. Shiva Kumar, G. Sreedhar, S. Sharma

Some of the Indian origin iron ore deposits located in Bellary, Karnataka province are having peculiar characteristics of Iron ore deposits (Hematite) having Iron above 64% and 30-40% lump (-30+6mm) recovery which are not suitable to use in blast furnace due to not meeting the specification of Tumbler Index and Abrasion Index. In general for high grade Iron ores, process flow sheet involves crushing and screening (dry/wet). In the contest of high grade Iron ores located at Bellary sector of Karnataka state in India, lump generated from this process could not attain the required physical properties (Tumbler Index, Abrasion Index) and metallurgical properties , even though the grade of the lump ore is above 64% Fe. Washing techniques like Drum scrubber and Log washer play major role in improving the metallurgical properties of Iron ore lumps by removing the light and hard layers of clay, silica coated over the lumps. In this study the effects were compared of drum scrubbing and log washing on iron ore lumps. It is found that by incorporating simple washing technique i.e. drum scrubbing or log washing, Tumbler Index of Iron ore Lumps could be increased from 74% to 78% which is acceptable for use in Blast furnace. From the Drum scrubber and Log washer tests, it is clear that Log washers have an edge over Drum scrubber in removing hard coated clay on surface of Lumps. This simple washing technique facilitate us to utilize the lumps directly in blast furnace and eliminate the unnecessary crushing and grinding of the ore so as to meet the specifications of Sinter fines and pellet feed.

Jan 1, 2014

By Fu Ping-Hao, J-P Franzidis, Sergio Mauricio Vianna, Ewen Silvester, Emmy V. Manlapig

"Over the last 5 years, an ambitious project has been undertaken at the Julius Kruttschnitt Mineral Research Centre (JKMRC) aiming to isolate, study and, if possible, model the effect of particle size, liberation and collector adsorption density on the floatability of mineral particles. As part of this project, we have conducted highly controlled flotation test-work, combined with state-of-the-art solution and surface analytical techniques such as High Performance Liquid Chromatography (HPLC), Time of Flight Secondary Ion Mass Spectroscopy (TOF-SIMS) and detailed mineralogical analysis to fully characterize the flotation behavior of a natural ore.The flotation tests were undertaken using a high-grade lead-zinc ore from BHP-Billiton's Cannington mine (Australia) in a specially designed continuously operated laboratory scale flotation rig. Solution and adsorbed collector concentrations were measured independently during the course of the flotation tests using HPLC based ex-situ techniques. Liberation studies were performed using the JKMRC Mineral Liberation Analyser (MLA) on selected size intervals of different streams to estimate the specific surface area of galena. These results were used to calculate the collector adsorption density (collector coverage) on galena particles, with the eventual aim of developing a mathematical model describing the relationship between pulp chemistry, feed mineralogy, and floatability of galena particles."

Jan 1, 2003

By Chiharu Tokoro

Acid Mine Drainage (AMD), high acid water containing heavy metals discharged from mines, has been recognized as major cause of mine pollution. In Japan, the government spends billions of yen every year to prevent pollution caused by AMD in about 80 abandoned mines. It is widely recognized that the treatment could continue for long decades or an even century. However, costs and environmental loads are uncertain during the treatment because a predictive model for the quality of AMD, the dosage of neutralizer, and the amount of sludge that is applicable for abandoned mines with limited data has not yet been established. In this study, a two-steps predictive model for solution composition and neutralization chemical requirements of AMD in future was constructed based on the geochemical modeling. Requisite input data of the model was the past historical water quality data from AMD monitoring, such as metal concentration and pH in the solution, instead of the sample rocks as other conventional prediction methods. In the first step, solution composition of AMD in the future was extrapolated from the available historical data using geochemical simulation considering the first order kinetics for the mineral dissolution. In the second step, neutralizer dosage and sludge generation in the future was predicted based on the geochemical simulation supposing the chemical equilibrium and oxidation state for all of elements in the solution. Based on case studies of two abandoned mines in Japan, solution composition, neutralizer dosage and sludge generation were estimated. The results of this study demonstrate the effectiveness of our model for the prediction of AMD quality and chemical requirements of neutralization treatment after mine closing. The model is useful for the estimation of the neutralizer dosage and the sludge volume in abandoned mines with limited data. Keywords: acid mine drainage, predictive model, geochemical modeling, first order kinetics, water monitoring

Sep 1, 2012

By Slobodan B. Vujic

"Some twenty years ago, during construction of flotation in the “Veliki Krivelj” copper and non-metallic mine Bor, a computer supported system for remote controle of technological process was installed. Nowadays, the major part of equipment of this system is worn-out and technically old-fashioned. Having this in mind a decision was made to design a new computer supported information-management system for Flotation. The paper presents a concept and features of project solutions.For the requirements of remote monitoring and management of technological process in Flotation of “Veliki Krivelj”, Copper and non-metallic minerals mine in Bor, Yugoslavia (hereinafter: CNM Bor), a measuring-regulation equipment was implemented and a computer control system, adjusted for that time, built some twenty years ago. The major part of this equipment is today worn out and technically out of date.Having estimated that production and business activities could hardly be more efficient, operative and successful on one hand, and available mineral and other resources rationally exploited, the CNM Bor made a decision in 1999 to improve information-management function of Flotation. The idea was that the set task be realized through development and introduction into practice up-to-date integrated and computer-supported production-business information-management system. The first logic step in completion of this task refers to engineering-creative determination of information management system (hereinafter: IMS), namely to project elaboration.When considering the real system from technical, technological, organization, monitoring-management, logistic and business aspects, the Project on IMS of Flotation, should provide a rational, modern and, for the real system conditions, complete solution. The Project solutions should be based on the most recent knowledge from computer and measuring-regulation technics as well as from CIM concept (Computer Integrated Manufacturing)."

Jan 1, 2003