Search Documents

By Erico Tabosa, Kym Runge, Peter Holtham

"The distribution of turbulence in an industrial scale mechanical flotation cell and its effect on flotation kinetics was studied using a fully instrumented 3m³ cell. The cell was operated at a copper concentrator in Australia with different combinations of airflow rates, impeller speeds and sizes and cell aspect ratio providing a wide range of hydrodynamic conditions. An analysis of the overall flotation cell performance showed that the overall copper recoveries were very similar for the conditions tested. However, by decoupling pulp effects from froth effects it was possible to evaluate whether the changes made affected the pulp zone and/or froth zone responses. The analysis showed that the overall recovery has the potential to be up to 7% higher, if not limited by froth recovery. The cell hydrodynamics were characterised by the overall energy dissipation rate and, to understand the distribution of turbulence within the cell, localised measurements were made using a piezoelectric vibration sensor. By comparing the metallurgical performance of the cell with the different hydrodynamic conditions it was found that the collection zone flotation rate constant was not directly related to overall energy dissipation, as is commonly observed at laboratory scale, where energy is usually only changed by varying impeller speed. In this study, energy dissipation rate was varied using not only impeller speed, but also the size of the impeller and the cell aspect ratio. In these circumstances, the best correlation was found to be between the collection zone flotation rate constant and the distribution of turbulence, i.e. the size of the turbulent zone."

Jan 1, 2014

By W. H. Cheung

Nickel (Ni) plays a major role in the production of steel and other major alloys. There are two sources of Ni: laterite and sulphide ores. Global reserves of sulphide ores are being rapidly depleted, while there are enormous reserves of Ni laterite, much of it in Australia. As well as being present in huge amounts, Ni laterites have the advantage of containing cobalt (Co), a valuable mineral. Over the past decade, these factors have been driving the industry to explore the processing of Ni laterite. A route that has been used commercially in processing nickel laterite ore involves the thermal activation of the minerals by pre-reduction followed by ammoniacal leaching (Caron). Although this process has been effective in processing the goethite rich laterite minerals, the higher-grade serpentine-based minerals have been shown to be less susceptible to this process. This has been attributed to the formation of inert olivine phases. In this study, we examined the use of an alternative lixiviant, sulphuric acid, in leaching pre-reduced limonite and weathered saprolite nickel laterite ores. The specific aim of this study was to examine the sulphuric acid leaching of Ni and Co from pre-reduced laterite minerals, and to understand the role of mineral transformations in this metal dissolution. Synchrotron based X-ray diffraction was used to examine the transformation of goethite (FeOOH) to spinels and serpentine mineral ((Mg,Fe)3Si2O5(OH)4) to olivine. Reduction tests were carried out using CO and CO2 reducing gas mixtures and temperatures from 400 °C to 700 °C. The rate of formation and disappearance of specific Bragg peaks during reduction of specific minerals were used to derive an understanding of these solid-state reactions. Laboratory based reduction tests and leaching in sulphuric acid were used to validate the effect of these mineral transformations. The results suggest the versatility of sulphuric acid in leaching nickel from spinels and olivine, which was achieved at the expense of lower selectivity. Cobalt dissolution was found to be dependent on the nature of ferro-cobalt alloy formed during reduction.

Jan 1, 2014

By Ghislain Bournival, Seher Ata, Yesenia Saavedra Moreno

"In froth flotation, frothers are commonly added to the pulp to modify the interfacial properties of bubbles. These properties may be modelled using commercial software packages. The volume of fluid (VOF) method was used to track the interface motion during the post-rupture oscillation of the newly formed bubble. The aim of this research was to provide an insight into the modelling of viscoelastic phenomena through the coalescence dynamics of two bubbles in solutions of various surface tensions using a three-dimensional computational study. Different surface tensions were used to simulate changes in methyl isobutyl carbinol (MIBC) concentration. The computational results were evaluated by comparing the oscillatory motion of the newly formed bubble for the different MIBC concentrations. For known MIBC concentrations, the deviations of the computational damping constants from the experiments were quantified, revealing possible deviations in the VOF surface tension model. In addition, the analysis provided insight into the flow patterns of the fluids and the effect of frother concentration on the velocity magnitude in the liquid and air phases. This analysis provided a further understanding of coalescence dynamic and post-rupture oscillation in froth flotation. Such a process is believed to affect the stability of particles at the interface due to the release of surface energy when the bubble surface is reduced.INTRODUCTIONIn froth flotation, bubble coalescence is an important phenomenon that is highly dependent on the interfacial properties of the liquid film between bubbles. It is known that the frother adsorption at the liquid-air interface changes the interfacial properties, resulting in an increase of surface elasticity and reduction of surface energy (Pugh, 2016). However, in a two-phase system, it is the frother type, concentration, frother molecule conformation at the interface and viscoelasticity properties that dictate film stability (Pugh, 2016). The viscoelasticity phenomena can be explained in terms of surface viscosity, which quantifies the energy dissipation at the interface and surface elasticity that represents the energy absorbed at the interface as result of bubble oscillation (Pugh, 2016). In the case of systems stabilized by nonionic frothers, it has been shown that surface forces alone do not account for film stability, but the viscoelasticity represents the ability to damp external disturbances in the thin film separating the bubbles and prevent coalescence (Santini et al., 2007)."

Jan 1, 2018

By B. Das

The separation of iron values from a typical Indian iron ore slimes containing 57.2% Fe, 5.81% SiO2 and 7.05% Al2O3 by wet magnetic separation and selective magnetic coating is investigated. The iron phases, which are mostly paramagnetic in nature, have been coated with magnetite or colloidal magnetite in presence of surfactant by manipulating the surface properties of the minerals. The studies have indicated that an iron concentrate containing 62.32% Fe with 66.5% iron recovery can be obtained at medium magnetic intensity of 7.8 kG which is much less compared to normal magnetic intensity of 13 kG to14 kG required for hematite-goethite separation. The performance of this technique with respect to both grade and recovery is superior to conventional magnetic separation or flotation of iron ore slimes.

Jan 1, 2014

By Z. T. Yuan, S. L. Qi, Q. Y. Meng, G. X. Zou, L. X. Li, J. W. Lu

"The selective separation of pentlandite from serpentine was investigated using the magnetic coating-magnetic separation by conditioning slurry pH value, stirring speed, magnetic field intensity and controlling dosages of sodium hexametaphosphate (SHMP) and sodium oleate (SO). The optimal conditions were obtained as follows: the natural pH of 6.8-7.2, stirring speed of 2300 rpm, magnetic field intensity of 200 kA m-1, SHMP of 60 mg L-1, and SO of 400 mg L-1. Results showed that the Ni grade was 21.4% with the Ni recovery of 81.4% and MgO content of 3.8%. FTIR indicated that coagulant of SO preferentially adsorbed onto pentlandite and magnetite particles while hardly adsorbing onto serpentine particles when dispersant of SHMP was used. Thus, the selective magnetic coating of magnetite on pentlandite surfaces could be formed due to the formation of hydrophobic surfaces on pentlandite and magnetite particles. Calculations of DLVO (Derjaguin-Landau-Verwey-Overbeek) confirmed that interactions between magnetite and pentlandite particles were much stronger than that between magnetite and serpentine due to the existence of hydrophobic interactions with the addition of SO. Consequently, the pentlandite was successfully separated from serpentine. Therefore, this study exhibits the potential to separate pentlandite from serpentine minerals for practical applications and thus deserves further study.INTRODUCTION It has been well known that the separation of pentlandite from serpentine is a worldwide challenging issue in the processing of sulphide nickel-copper ores. Because the serpentine mainly causes the high pulp viscosity and slime coating on the pentlandite, which interferes with the flotation process of pentlandite (Cao et al., 2016; Feng et al., 2012). The fibrous mineral of serpentine preferentially attaches to the air bubble, forming bubble-macrofibers aggregates, which are easily floated into the nickel concentrates, resulting in the decline of Ni grade (Alvarez-Silva et al., 2016; Kusuma et al., 2014). In addition, the serpentine adheres to the pentlandite as hetero-aggregation or slime coating via the electrical interaction between a positively charged serpentine and a negatively charged pentlandite, which decreases the hydrophobicity of pentlandite and reduces the collector adsorption (Feng et al., 2013). In other words, the presence of serpentine or the occurrence of aggregates (including slime coating and bubble-macrofibers aggregates) seriously affects the flotation process and deteriorates the flotation of pentlandite. Therefore, we propose magnetic separation to recover pentlandite from serpentine with the magnetic coating technology, which is different from forth flotation."

Jan 1, 2018

By Danuta Szyszka

This paper presents results of tests performed to determine minimum concentration of a surfactant used at which coalescence of air bubbles during flotation has low probability to occur. The measurements of the critical coalescence concentration, also known as CCC, were carried out in a device consisting of glass cell into which air was pumped by peristaltic pump through capillaries. The flotation foam was recorded with a high resolution digital camera. Basing on the video records, average diameters of the air bubbles were measured and the values obtained were subsequently used to determine the CCC values. The author of paper determined the CCC values of surfactants tested using the linear regression method, and subsequently analyzed the results obtained. To define initially the capability of a tested surfactant to flotation, efficiency of multiparticle model flotation and flotation of individual size fractions were determined in a flotation apparatus for laboratory use in the presence of only foam making agent at CCC value pre-determined during the tests previously carried out. The tests of coalescence phenomenon were carried out with use of selected flotation frothing agents.

Jan 1, 2014

By Charlene Gokhale

Geopolymerisation has emerged during the last few years as an industrial and ecological approach to construction and waste management. By utilizing waste materials and their reactive properties, it is now possible to create geopolymers systems that not only mechanically durable enough to be used as construction materials but are also potential stable immobilisation systems for toxic waste. Previous studies by Van Jaarsveld et al. (1997) and Van Jaarsveld et al. (1998) have reported on the numerous applications of geopolymers in the immobilisation of toxic metals. Research into the possible utilisation of geopolymers as an encapsulation media for organic waste has however been rare. This paper therefore provides an insight into the possible utilisation of geopolymers as a binder for hazardous organic materials.

Jan 1, 2003

By Shuji Owada, Yang Geng, Natsuko Kuroki

Micro-bubble flotation is considered to be an ideal method for the separation of fine or ultra-fine particles, which are difficult to be separated with conventional flotation and other solid separation technologies. Micro-bubble flotation can increase the probability of bubble-particle collision more than conventional milli-bubble flotation. However, there are also some problems. For example, it is known that the rising velocity of micro-bubble is quite low; therefore, the flotation rate reduces. And also, the bubble-particle adhesion probability becomes lower than that of milli-bubble flotation, which is proved in our prior research. In this paper, we applied ultrasonic irradiation to the micro-bubble flotation system in order to solve the above problems and focused on the bubble-bubble and bubble-particle interactions. For clarifying the behavior of bubble-bubble interaction, bubbles behavior was recorded by high-speed camera under irradiation of various ultrasonic frequencies. As a result, in the case of bubble-bubble interaction, it is proved that bubbles are highly coalesced by ultrasonic irradiation especially in the lower frequency and it can enhance more precise separation. In the case of bubble-particle behavior, it is found that the floatability become higher with the ultrasonic irradiation of higher frequency, and it is indicated that ultrasonic irradiation might improve the bubble-particle adhesion probability. Additionally, it is also found that the apparent CMC of the micro-bubble flotation under the ultrasonic field become much lower with higher frequency than with lower frequency, and it is suggested that the dramatic improvement of hydrophobization is achieved.

Jan 1, 2014

By Graeme J. Jameson

"When mineral particles are floated in a mechanical flotation cell, it is found that the rate constant, after reaching a maximum value, starts to decline as particle size increases. It had been thought that the reduction in rate constant had been due to the increased prevalence of composite particles in natural ores, for larger particles. However, Jameson (2012) showed that the rate constant for composites is certainly a function of the surface liberation, but the reduction in flotation rate is independent of particle size. Thus all particles are equally affected by reduced surface liberation, independently of their size. He further argued that the classical peak observed in the rate constant with increasing particle size, is a function of machine hydrodynamics. Thus in mechanical cells, the peak may be due to the high energy dissipation rate and its effects on the detachment of particles from bubbles (Goel and Jameson, 2012). Consequently, in a different flotation environment, it may be possible to float large composite particles that cannot be floated in mechanical cells. This paper describes the flotation of large composite particles in a fluidized bed flotation cell. The particles to be floated are fed to a column in which there is a continuous upflow of liquid. A conventional froth layer of controlled depth is formed at the top of the vessel. A fluidized bed of particles is established which provides a gentle environment for the contacting of large particles with bubbles. An example is given where a porphyry copper ore was prepared at a top size of 710 µm, and floated with conventional collector (PAX) and frother (MIBC). The concentrate was separated into size fractions and examined by photography. Composites were observed at all size fractions, but above 400 µm, all particles were composites. The implications for future flotation circuits will be described."

Jan 1, 2014

By A. Wieniewski

The observed progress in technology of non-ferrous ores enrichment and condition of machines and equipment in the ores concentrators on the one hand have brought a possibility and on the other resulted in necessity for introduction of modernization actions. Positive results of investigations into influence of chemical modification of selected products of enrichment process on copper ores enrichment results gave possibility for implementation of chemical-flotation technologies of ores enrichment. The substantial development in flotation machines structure has contributed to modernization of flotation process resulting in increase of enrichment efficiency. The paper presents the idea and results of chemical modification of difficult in enrichment semi-products in the technology of copper ores enrichment and the results obtained after application of the modernised technology. The structure of large-volume flotation machines used in various stages of flotation and current situation in modernization of flotation process in copper ores concentrators are also described. The paper presents industrial-scale results of flotation after application of modified flotation reagents of collector group. Introduction of modifiers into the widely used xanthates resulted in increase of copper recovery in concentrate.

Jan 1, 2014

By S. Kelebek, M. Davidson

"Flotation tests were conducted on a mixed copper ore sample containing bornite and malachite with trace quantity of other secondary copper minerals. The bornite component was very floatable, in sharp contrast to poor flotation characteristics of other copper minerals. A Box-Behnken experimental design methodology was used to study effects of three main reagents, namely potassium amyl xanthate (PAX), hydroxamate (Cytec 6494) and diethylenetriamine (DETA). Pine oil, as a frother, was used at a fixed concentration. Three main models constructed using a statistical software included malachite recovery, overall copper recovery, and copper grade. Bornite recovery was not modelled as its recovery was consistently over 99 % in the presence of hydroxamate and PAX. In each model, the hydroxamate dosage was the dominant parameter (at 95% significance level) determining the recovery of main components including that of gangue, which manifested itself by lowering the copper grade of the concentrate. In comparison, PAX was effective only at 90% significance level. DETA did not affect the overall recovery of copper or malachite significantly, but appeared to cause a significant decline in the concentrate grade, especially when used simultaneously with hydroxamate. Various quadratic models developed for the flotation system investigated are presented."

Jan 1, 2014

By Chao Li, Kym Runge, Saeed Farrokhpay, Dee Bradshaw

"It is well known that froth phase has a controlling influence on the overall flotation performance. Froth recovery is expected to be affected by froth transportation behaviour. The latter has been represented by different volume balance and energy balance based models. In froth transportation models based on a volume balance, the froth phase is divided into different zones. The total froth residence time is the sum of the time spent in each zone and is dependent on the cell geometry, bubble burst rate and the position that bubbles enter into the froth phase. Alternatively, the froth transportation model based on an energy balance treats the froth phase as a block. In this model, froth height above the concentrate lip is being predicted by minimising the energy of the system which is dependent on the froth geometry, froth stability and froth rheology. The froth height can be used to calculate the froth efficiency of delivering mineralized bubbles from the pulp to the concentrate lip. This paper critically analyses the current models of froth transportation in flotation, and examines the limitations of these models. The importance of froth rheology, which is the resistance to the froth flow towards the discharging weir, in determining froth transportation, is also highlighted."

Jan 1, 2014

By P. Hatefi, O. Rahmani, M. Noor-Mohammadi, A. Tohry

"Depressants play an important role in the selective separation of impurities from iron minerals by direct or inverse flotation. In this paper, sodium co-silicate (SCS) with chemical formula of Na4SiCO6, as a depressant with pH modifier features, has been synthesized and used for phosphorus bearing iron ore in anionic reverse flotation. In this process, phosphorus is floated while the iron oxides are depressed, using fatty acids as collector in an alkaline medium. Batch and pilot flotation tests were carried out to investigate the influence of SCS on the separation selectivity of phosphorus from iron oxides. Also the depression mechanism of SCS on hematite surface was investigated by microflotation tests and FTIR spectroscopy measurements. The flotation results indicated that without using a pH modifier, the pH of pulp could reach up to 10, when SCS was used as depressant. In this condition, a better depression performance was observed compared to sodium silicate (SS). Using the SCS, phosphorus and total iron content in iron concentrate was 0.046% and 66.29%, respectively, compared to SS where these values were 0.06% and 65.75%, respectively. As a result the weight recovery of iron concentrate was increase by around 4%, compare to SS. It was also found that 238 g/t of SCS could be used instead of 3 types of reagents collectively, including 32 g/t of NaOH, 151 g/t of Na2CO3 and 400 g/t of SS gel.INTRODUCTIONThe phosphorous presents in iron ore minerals is mainly in the form apatite mineral. The apatite is separated from iron ore minerals by magnetic and flotation methods (Ma, 2012). The reverse anionic flotation of iron is one of the most common method for removing phosphorus from iron concentrate (Araujo et al., 2005).Usually apatite minerals are readily floated using anionic collectors such as fatty acids (Ma, 2012). In this conditions the iron minerals are depressed and by modifying the pH in alkaline conditions, selective separation of phosphorus from iron concentrate can be achieved. Depressants including; sodium silicate (SS), starch, dextrin, guar gum and humic acids play an important role in the reverse flotation of iron ore (Kar et al., 2013; Ma, 2012; Turrer and Peres, 2010; Araujo et al., 2005). Studies have shown that SS has a better effect on iron recovery and phosphorous reduction, compared with other depressants (Tohry and Dehghani, 2016; Qi et al., 1992, Dho and Iwasaki, 1990). In most flotation processes, modifiers are used to adjust the pH. To achieve alkaline conditions, mainly pH modifiers such as carbon dioxide and sodium carbonate are used."

Jan 1, 2018

By Nirmal Weerasekara, Malcolm Powell, Mohsen Yahyaei

"The conditions under which rocks become superficially damaged during the grinding process are not well understood. The main purpose of the work presented here is to understand how superficial breakage occurs under incremental low-energy impacts. To enable this study a series of abrasion tests with multi-size pilot mills have been performed. Outcomes of numerical simulation corresponding to each test were examined to investigate the experimental results. Abrasion tests have been conducted using three grinding mill sizes (i.e. 1.8, 1.2, and 0.8 m). Two types of ore were used to investigate different hardness strengths. To ensure abrasion was the dominant mechanism, in all tests the mill speed was reduced to 40% of critical speed. The relationship between the Fractional mass loss rate and particle size was investigated by randomly collecting seven tracer particles from sizes -73+63, -53+45, and -37.5+31.5 mm. It was evident from the results that the Fractional mass loss rate of angular particles declines as the particle size increases whereas the Fractional mass loss rate decreases from fine to coarse in rounded particles. Results of Discrete Element Method (DEM) simulations indicate that fine particles experience higher levels of collision energy per particle and this value reduces as the particle size increases and mill size reduces. This explains the higher Fractional mass loss rate of smaller particles as well as the increase in the Fractional mass loss rate as the mill size increases. Linked DEM and experimental data indicates that under these test conditions surface damage attrition is the dominant mechanism. This work suggests that DEM simulation can be implemented to predict the abrasion wear of particles in mills."

Jan 1, 2014

By Peter J. Scales

The recovery of water for re-use in minerals processing is an important issue in the reduction of water use in mining, as is the dewatering of tailings to reduce the propensity of ?wet? tailings dams. It is common in these dewatering operations to use thickeners whereby polymeric flocculants are combined with the dilute feed to the thickener to aid sedimentation and the subsequent consolidation of particulate materials. Thickeners are the workhorses of water recovery and tailings dewatering and although the basics are well understood, there is still no ability to reliably predict the throughput and underflow density from a thickener based on traditional sedimentation tests and flux analysis. The reasons for the discrepancy between full-scale operations and predictions based on laboratory tests are numerous, including difficulties in mimicking the flocculation conditions experienced in the field and the shear conditions in the thickener. The latter effects are little understood and hard to quantify and include effects due to flocculated aggregate densification, complimentary shear and compressional effects and aggregate break-up. Developing a set of test protocols to quantify the effects of densification, shear in compression effects and aggregate breakup and the subsequent contributions of each to compressional dewatering in a thickening environment has been completed for a simple model polymer flocculated particulate suspension. The data and analysis shows that aggregate densification is a dominant contributor to the difference between observed and predicted behavior based on laboratory tests. A major consideration in the analysis is the fact that common thickener operations are permeability limited and although the various effects are all important, the one that results in the fastest water release is dominant. Of interest also are the shear rate, concentration, and time dependence of the aggregate densification process. A basic model of the process has been developed along with network yielding tests conducted using rheometry. Keywords: compressional dewatering, gravity thickening, rheometry, aggregate densification, raked batch settling

Sep 1, 2012

By D. J. Zhao

The reduction and nitridation of preoxidized ilmenite pellets were investigated with the prospect of creating grain refiners containing titanium oxides and titanium nitride dispersoids. All the reduction and nitridation reactions were conducted in a furnace with a thermogravimetric analysis system under a H2-N2 gas mixture of 5 L/min. The ilmenite pellets were reduced at 1100°C for 4 hours under 80%H2-20%N2 gas mixture, and then respectively nitrided at 700°C, 800°C, 900°C and 1000°C for 12 hours under 10%H2-90%N2 gas mixture. The products were characterized by X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM), and analyzed by Energy Dispersive Spectrometers (EDS) and Electron Probe Mapping Analysis (EPMA). Iron oxides were reduced into metallic iron, and oxides of titanium were found, but titanium nitride particles were not identified in the products under the prevailing conditions.

Jan 1, 2014

By T. Fujita

A high-grade fluorite ore is converted into hydrogen fluoride to produce many kinds of materials containing fluorine. Recently, it is becoming necessary to use low-grade fluorite ore due to the depletion of high grade ore. The low-grade fluorites usually have impurities such as SiO2, P, CaCO3 and arsenic. The most impurities such as SiO2, CaCO3 and P can be removed by using flotation method. However, the removal of arsenic is difficult, and the arsenic contamination decreases the hydrogen fluoride production percentage. The novel technologies for processing low-grade fluorite ore are urgently needed, in order to lower the arsenic concentration to less than 100 mg/kg. In this study, the removal of arsenic from low-grade fluorite ore has been investigated by means of an autogenous grinding using tower mill in sulfuric acid aqueous solution and 0.3 mm zirconia balls in water. The nano grinding in water can prevent the dissolution of 0.3 mm size zirconia balls as grinding media by sulfuric acid solution. Experimental results showed that the arsenic concentration was reduced from 260 mg/kg to 90 mg/kg and CaF2 recovery reached 90% by this process.

Sep 1, 2012

By R. ?. Sherembayeva, ?. ?. ?uktybayeva, ?. B. Rakhimbekova, N. ?. ?m?rova

"Studying the interaction of the phosphorus-containing flotation reagent with the components of the flotation system ""liquid-gas-solid"" during flotation of non-ferrous metal ores allows regulating the enrichment process. The phosphorus-containing reagent-collector anabasinium-O,O-dimethyl-thiophosphate has beensynthesized under laboratory conditions and the concentrated aqueous solution of anabasin hydrochloride and the 40% solution of sodium hydroxide have been used as the raw material. The phosphorus-containing reagent has been obtained by interaction of the anabasine base, sulfur and dimethyl phosphite, due to sulfur and nitrogen atoms it can form complex compounds with heavy metal ions.Studying flotation of copper-sulfide ore of the Sayak field with the use of the phosphorus-containing reagent-collector anabasinium has been performed in the open and closed cycles. The degree of ore grinding was 60- 62% of the class -0.074 mm. There has been established the dependence of the ore flotation parameters on: a) pH of the pulp; b) the consumption of the reagent-collector anabasinium.The effect of the pulp pH on the technological parameters of copper ore flotation has been carried out with a reagent regulator that increases the difference in the surface properties of the minerals to be separated.There has been used lime as the regulator of the medium, the consumption of which varied from 750 to 1500 g/t; the consumption of the reagent-collector anabasinium was 10, 15, 20 and 25 g/t.It has been found that when flotation of copper ore without the use of lime at pH equal to 7.8 and at the reagent consumption, g/t: anabasinium - 25, T-92 - 55, copper recovery in the concentrate is 92.72%, the quality of concentrate is 7, 1%.In flotation according to the factory mode (the consumption of xanthate is 44 g/t, T-92 is 55 g/t, pH = 7.8 (without lime)) of copper ore, copper recovery in the concentrate is 87.38%, the concentrate quality is 7, 97%, with reducing the xanthate consumption to 25 g/t copper recovery is reduced to 83.39%, the quality of the concentrate is up to 6.69%.In the experiments using the factory reagent mode in the closed cycle, with the xanthate mass consumption of 44 g/t, T-92 blowing agent of 55 g/t, the third recleaning concentrate contained 19.13% copper with recovery of 86.89%.Using a phosphorus-containing reagent instead of xanthate with the same flow rate, the third recleaning concentrate with the mass fraction of copper of 19.82% has beenobtained with recovery of 87.77%."

Jan 1, 2018

By G. Granata, C. Tokoro, T. Kato

The rare earth elements (REE) are composed of 17 elements that are 15 elements of lanthanide added scandium and yttrium. REE are divided into light rare earth elements (LREE) and heavy rare earth elements (HREE). Although the supply source of LREE is distributed around the world, the supply sources are unevenly distributed. Thus, the development of a new HREE supply source is required. In this study, we focused on the weathered residual rare earth ore as a new HREE supply source. Since so far this weathered residual rare earth ore could not be treated neither by flotation nor by wet high intensity magnetic separation, it was not considered as HREE resource before. In this study, we investigated the leaching of HREE from the weathered residual rare earth ore and elucidated the effectiveness of planetary milling with sodium hydroxide as a method to enhance their recovery. For this purpose, the weathered residual rare earth ore was first grinded by planetary mill in the presence of sodium hydroxide and then leached by sulfuric acid. The influence of planetary milling on HREE recovery was investigated by assisting the leaching experiments with X-ray absorption fine structure (XAFS) in cerium and yttrium K-edge. Since yttrium was the most contained HREE in the weathered residual rare earth ore used in this study, we focused on yttrium in XAFS analysis. Results clearly showed that the recovery of HREE increased by planetary milling with sodium hydroxide. XAFS analysis revealed that a part of the yttrium in the weathered residual rare earth ore was changed to yttrium hydroxide by planetary milling with sodium hydroxide. It is supposed that all HREE were affected like yttrium due to a similar behavior observed in leaching.

Jan 1, 2018

By I. Zimbovski, T. Ivanova, E. Chanturiya

"The mechanism of selective action of new reagent-collector AMD of phenylpyrazolone class with sulphide minerals of copper-zinc ores was theoretically and experimentally investigated. The validation was carried out using spectrophotometry, Fourier-transformed spectroscopy, laser scanning microscopy, analytical scanning electronic microscopy and flotation. The reagent AMD in alkaline medium on chalcopyrite and sphalerite surfaces is chemically sorbed, forming strong hydrophobic complexes with copper and zinc. On the pyrite surface, AMD acidifies ferric iron ions with formation of hydrophilic oxidates. The selectivity of collector AMD with separation of sphalerite and pyrite in alkaline condition (??=10) is confirmed by flotation experiments. With AMD, the obtained recovery of sphalerite was 34.4 % at extraction of pyrite of 3 and 6 %. The low recovery of sphalerite is caused by weak collective ability of the reagent. The use of copper sulfate increases the flotability of sphalerite up to 82.0 % at extraction of pyrite of 5 and 2 %. It has been experimentally determined that during the flotation of sphalerite and pyrite by AMD reagent with addition of butyl potassium xanthate, and in the presence of copper sulfate and regulator of formation of ammonium thiocyanate complexes, the recovery of sphalerite is increased to 91 %, while the recovery of pyrite is decreased to 3.8 %. The chalcopyrite is floated actively (90 % recovery). The results of all theoretical research and experiments were confirmed by flotation tests on ores and products of dressing in industrial conditions."

Jan 1, 2014