Search Documents

By D. Izerdem, S. L. Ergun

"Beneficiation of the finely disseminated valuable minerals has been an important issue in the mineral processing field for decades. Treatment of the fine materials becomes difficult with using traditional gravity concentration equipment. To investigate particles behavior in a commonly used conventional gravity concentration equipment, a comprehensive study was undertaken in a plant, which only consists spiral concentrators as concentration units. Spiral concentrators require relatively coarse material to effectively concentrate valuables as well as offering greater simplicity for especially higher grade feeds. In the current work, chromite ore (d80 = 290 µm) was treated using spiral concentrators and the performance of spiral concentrators was examined. The design of the separation circuit comprised of rougher, cleaner and scavenger stages. The resultant fractions produced by each separation unit and feed samples were analyzed to identify the particle sizes, mineral liberations and chromite content. Grade and recovery comparisons were presented in size-by-size manner and the separation tendency of the particles were determined in varying feed rate conditions. The overall results indicated valuable mineral loss of the plant and alternative suggestions were pointed to reach the target values.INTRODUCTION Spiral concentrators are simple low energy consuming devices, which are generally used for pre-concentration of the minerals. They are cost efficient equipment separating minerals mainly based on density differences of the minerals. The adjustable splitters remove the concentrate as the remaining stream continues to move down the spiral. Separation on a spiral is achieved through a combination of forces that act on particles as they move down the trough of the spiral. The main forces known to act on the particle on a spiral are the gravitational force, centrifugal force, hydrodynamic drag and Bagnold force (Atasoy and Spottiswood, 1995; Burt, 1984). Since the classification in a spiral concentrator depends on particle specific gravity and size, the operation of spirals can be analyzed using size recovery or partition curves (Bazin et al., 2014). Spiral concentrators possess multiple design parameters for a variety of applications. The design parameters that govern the performance of the spiral can be identified as the diameter, number of turns, slope, pitch and the profile of the trough. For an efficient separation on a spiral concentrator, the properties of the slurry flowing on a spiral, ore texture, percent solids and flow rate play important roles."

Jan 1, 2018

By F. S. Hoseinian, K. Filho, D. Deglon, T. Souza, M. Safari

"This paper investigates the reverse flotation of hematite in three laboratory flotation cells with very different contacting environments. The main objectives are to investigate the recovery of coarse quartz by flotation and fine hematite by entrainment. The laboratory flotation cells used were the mechanical, oscillating grid and pneumatic cells. The effect of froth height and solid concentration were investigated in the mechanical and pneumatic cells. The effect of impeller speed and energy input were investigated in the mechanical and oscillating grid cells. Froth height results show that coarse quartz particle recovery decreases almost linearly with increasing froth height due to increased detachment of coarse quartz particles in the froth. Fine hematite particle recovery also decreases almost linearly with increasing froth height due to decreased water recovery and associated entrainment. Agitation/energy input results show that coarse quartz particle recovery increases with increasing impeller speed to an optimum, after which this decreases dramatically. The increase is due to improved gas dispersion, generation of smaller bubbles and increased bubble-particle collision and attachment. The decrease is due to significantly increased bubble-particle detachment at higher impeller speeds. The recovery of coarse quartz particles in the OGC is higher than that in the mechanical cell with an optimum at a much lower energy input. Solids concentration results show that both mass recovery and water recovery increase with increasing solid concentrations. The pneumatic cell achieves higher mass recoveries and lower water recoveries than those in the mechanical cell at equivalent solids concentrations and operating conditions. INTRODUCTIONFlotation is a selective process for separating different minerals from each other. The flotation separation efficiency depends on the recoveries of the mineral species by both true flotation and entrainment (Neethling and Cilliers 2009; Wang et al. 2015). Both chemical variables and hydrodynamic conditions within the flotation cell affect the recovery and selectivity of the flotation process. Cationic reverse flotation of hematite is a common method for selective separation of quartz from iron ores to produce pellet feed. The presence of coarse quartz particles in the tailings and fine hematite particles in the concentrate are two major challenges in the reverse flotation of hematite (Vieira and Peres 2007)."

Jan 1, 2018

By E. Kusaka, M. EL Salmawy

"The electrokinetic behavior of EL Maghara coal has been investigated in the presence of nonyl and octyl nonionic surfactants containing polyethoxy of different sizes with trade names of Triton-X100 (TX-100), Triton-X 705 (TX-705), Triton WR-1339 (TWR-1339) and Brij 58. The electrokinetic behavior was determined by zeta potential measurements. Zeta potential measurements were conducted by Laser-Doppler electrophoresis technique using zetamaster. The results show that the zeta potential of Egyptian coal varies with pH value, the hydrocarbon chain and number of ethoxy groups in the hydrophilic group of the surfactant. It was found that the polymeric surfactants reduce the negative values of zeta potential of coal. The shift of PZC of coal upon deashing appears to be closely relevant to silicate mineral removal."

Jan 1, 2014

By P. Chris Pistorius, Johannes Sono, Rossouw Sono, J. J. Kobus

Different coal properties are important in SL/RN (coal-based rotary kiln) direct reduction of iron ore, and in electrical smelting of prereduced iron ore. These differences were highlighted when a plant which processes titaniferous magnetite had to change to different coal types after decades of operation. Laboratory simulation was used to evaluate two candidate coals, which were similar in volatile content and rank, but differed in reactive maceral content. Direct reduction was evaluated by isothermal experiments using a packed bed of ore and coal, measuring the off-gas composition to determine reaction rates and departure from equilibrium. These indicated reduction to be under mixed control, and quite sensitive to temperature (confirming that the coal reactivity is of importance). An aspect of electrical smelting was assessed by determining dissolution rates of the coal in molten iron at 1550°C. Dissolution rates did correlate with differences in coal structure, as determined by X-ray diffraction, with the more ordered ("more crystalline") coal dissolving faster. The conclusion is that the coal which is more reactive during direct reduction is less reactive during dissolution. However, it is concluded that controlling the temperature during direct reduction offers a feasible method to reconcile the two process steps.

Jan 1, 2003

By Wei Sun, Xue-feng Cao, Lei Sun, Run-qing Liu

The flotation performance of kaolinite in laboratory micro-flotation was investigated with 3- (dodecyloxy) propan-1-amine (ON12) as the collector. Compared with dode cylamine (DDA), which is commonly used as the bauxite reverse flotation collector, ON12 shows stronger collecting ability for kaolinite than using the same amounts of DDA, when experimental pH value reaches more than 6. With the addition of ON12, the isoelectric point of kaolinite shifts to 6.1 from 3.6, which suggests a strong adsorption between kaolinite and ON12. Infrared spectra analysis indicates that the type of ON12 adsorbed on the kaolinite surface is mainly of electrostatic adsorption. Molecular dynamics simulation further indicate that electrostatic adsorption of ON12 cation on kaolinite (001) surface based on electrostatic interaction between NH4+ and O atoms. ON12 will be suitable for bauxite reverse flotation with the efficiency depressors of the diaspora.

Jan 1, 2014

By E. V. Bratygin, S. P. Elnikova

"In the article carrying out technique of experiments for estimation of power efficiency of process of crushing in cone crushers «in a layer». The conformity of the granulometric characteristics of the crushed products obtained as a result of the tests, the theoretical equations for the size characteristics, and the choice of the optimal equation for the prediction of the granulometric characteristics of the final products obtained by crushing ""in a layer"". Optimization of granulometric composition of power of crushers working ""in a layer"" is carried out with the purpose of reduction of the electric power consumption at reception of a product of required quality. As a result of the experiments, dependencies are obtained, the relevance and applicability of the crushing process ""in the layer"" for obtaining crushed stone of improved quality is proved. INTRODUCTION A number of equations have been proposed for calculating the breakage energy. These include equations by Kirpichev and Kick, Rittinger and Bond (Bogdanov, Olevsky, 1982). Another equation for calculating the specific breakage work in breakage by impact and in stratum was proposed by Devyatkin (Boiko, 2003). In these equations, the breakage energy is proportional to the particle size raised to some power. In the equation proposed by Devyatkin, the ore piece thickness or the feed average diameter is used. The relationship between energy and breakage can be expressed as an equation (Lynch, 1981; Tikhonov, no. 3, 2008) where k is a coefficient characterizing the energy parameter depending on the strength of the feed, l is size in microns. The Rittinger formula is obtained for n = 2, the Kirpichev-Kick formula for n = 1, the Bond formula for n = 1.5. For n = 3 or higher, the equation describes fine and ultrafine grinding. R. Hookey proposed a formula (Lynch, 1981, Tikhonov, no. 3, 2008), where the size exponent n is substituted by a size function In all of the above equations, a single value of the feed and product size is used; for example, in the Bond equation, size is defined as the particle size of the 20% oversize (P80 and F80). However, a single size value can represent multiple distributions, making that the Bond method inappropriate for determining the size (Lynch, 1981). Describing an equation for estimating the grinding energy will allow to design the electric drive and ore preparation circuit for the given breakage method."

Jan 1, 2018

By L. A. Vaisberg, E. V. Shishkin, S. V. Kazakov

"This research is targeted at finding solution to the problem of reduction of specific energy consumption during disintegration of solid materials with the help of machines, operating in a quasiresonant mode. The objective of the research is the development of an energy-saving method of disintegration of supestrong rock and by-products on the basis of vibrational units with two movable crushing elements, operating in a rigorous synchronous-antiphase mode without stringent kinematic links. In the course of investigations a mathematical analysis of the dynamics of vibrational units was performed to determine required mechanical parameters, allowing for adjustment of the machine actuating elements to high-frequency synchronous-antiphase oscillations in the quasiresonant frequency range. As a result of performed pilot tests, the reliability of desktop studies was confirmed and the dependency of process parameters on the machine regulated parameters in the quasiresonant frequency range was identified. The analysis of obtained data showed that during machine operation with cone-shaped crushing elements in the quasiresonant frequency range, the yield of the high-quality finished product (WFA grits of -3+1 mm grain size class) in one pass reaches 35%, whereas the form of the particles corresponds to the grain form with sharp edge. The quasiresonant operation mode of the vibrational unit with two freely suspended crushing elements (without stringent kinematic links) provided substantial reduction of energy intensity during crushing down to 0.16 kWh/t, which shows reduction of power consumption for crushing by more than 15% compared to conventional equipment.INTRODUCTION The most common and energy-consuming processes in the mining industry are the crushing and grinding of various solid materials. Such large energy costs are due to the fact that the capabilities of the existing crushing and grinding machines are based on traditional methods of destruction, and are limited by their kinematic features, which do not allow to reduce the energy intensity of processes, to lower the irreversible loss of useful components, to improve the quality of marketable products. In connection with the foregoing, the task of energy costs reducing for disintegration is one of the most important issues in the enrichment of both minerals and processing of man-made raw materials. The solution of this problem is possible only through the creation of a fundamentally new highly efficient technique and technology for processing raw materials [1, 2]. It seems that the greatest prospects in this respect are the vibration methods of disintegration, in particular, the vibratory cone crusher based on a two-mass system without rigid kinematic connections between the crushing bodies, with vertical vibrations of the working bodies. In this machine, the principle of rational material destruction is realized – crushing without re-grinding [3-5]."

Jan 1, 2018

By A. Güney

Currently, recycling technologies use relatively homogeneous plastics because hand-sorting waste feed is too expensive. Many promising technologies for separating mixed thermoplastics are being investigated, but they are still uneconomical and unreliable. Burning plastics for recycling is not used because of poisonous gases released when their burning. PET and PVC cannot be separated using conventional gravity separation techniques because their specific gravities overlap; PET density changes from 1.33 g/cc to 1.37 g/cc and PVC density is between 1.32 g/cc and 1.37 g/cc. For this reason, plastic recycling needs new techniques. Among these techniques froth flotation, also used in mineral processing, can be useful for its cost and simplicity. In this method, a plastic is selected from mixture, tried to regain its natural property, hydrophobicity. In this study the experiments were applied by using plasticizer reagents to make the selected plastics hydrophobic and us-ing NaOH to render the other hydrophilic. Post-consumed PET and PVC are evaluated by concerning the effects of selected parameters (particle size, concentration of plasticizer reagent, amount of NaOH, conditioning time and the effect of conditioning temperature). At the end of the experiments, optimum parameters for selective flotation of PET from PVC was found as particle size of -4.76 + 3.36 mm, NaOH amount of 30 kg/t, conditioning temperature of 75°C, conditioning time of 30 minutes, reagent amount of 300 mg/L. Consequently, PET was re-covered with 99.7% purity and 57% efficiency.

Jan 1, 2014

By Masakazu Niinae, Kenji Aoki

"Electrokinetic soil remediation by electroosmosis and ionic migration is restricted to soluble substances. At a higher pH, the soil particles sorb more heavy metals than at a lower pH and the precipitation of heavy metals are promoted. Both mechanisms make heavy metals immobile, rendering cleanup more difficult and electrokinetic extraction inefficient.In this study, the effectiveness of introducing a complexing agent to enhance the removal of cadmium from kaolinite in the region of neutral pH by ionic migration is examined. The complexing agent selected was ethylenediaminetetraacetic acid (EDTA). The investigation was carried out in a laboratory-scale column containing kaolinite contaminated with cadmium. As the results of the study, cadmium migrates toward the anode without accumulation of cadmium and is successfully removed at the anode reservoir."

Jan 1, 2003

By Nirmal S. Weerasekara, Malcolm S. Powell, Mohsen Yahyaei

"An understanding of the fundamentals of different breakage mechanisms is critical for successfully modelling comminution processes. Due to the high frequency of low energy collisions in the grinding process, superficial breakage has a significant role in size reduction in mills. To develop a scaling up methodology for characterising low energy surface damage behaviour of ores, a series of surface damage tests have been conducted using three grinding mill sizes with diameters of 1.8, 1.2, and 0.8 m. Two types of gold-copper ore with different hardness were used: C-ore and T-ore. All tests were conducted using wet mode to remove the products during grinding. To ensure low energy surface damage was the dominant mechanism, in all tests the mill speed was reduced to 40% of critical speed. A surface damage index normalised with product mass and surface based specific energy is determined from the results enabling a study of the grinding performance regardless of mill size, energy level or charge mass. Incremental breakage tests using the JKRBT indicate that the A×b values of the T-ore were 60% higher than C-ore, suggesting the T-ore is considerably softer. The fractional mass loss rate for the T-ore in the 0.8 m and 1.8 m mills started from 16 and 7 (1/kWh/m2) while for the C-ore it was 4 and 2 (1/kWh/m2). After 6 minutes the surface damage index in all tests tends towards steady state a constant value, an indication of steady state surface damage condition. It has been demonstrated that this methodology can be a useful basis for characterising superficial breakage behaviour of ores."

Jan 1, 2014

By Marina Nicolova, Irena Spasova, Plamen Georgiev, Stoyan Groudev

Different strains of "silicate" bacteria were used to improve the quality of kaolin by different ways of treatment. All strains formed large slimy capsules consisting of exopolysaccharides and were related to different species of the genus Bacillus, mainly to B. circulans and B. mucilaginosus. It was found that even a short contact of some hours of well developed cultures of these bacteria resulted in improvement of the bending strength and the other ceramic properties of the kaolin. The improvement was connected with the action of some secreted microbial metabolites such as soluble heteropolysccharides, monosugars and organic acids. The best results were achieved by continuous cultivation of bacteria in the presence of kaolin with a high relative humidity and subjected to periodic stirring.

Jan 1, 2014

By Christopher Greet, Alfred Van den Bosch

"A range of media alloys with different chromium content has been developed for different milling applications. When selecting the grinding media alloy for a specific application, consideration must be given to the mineralogy of the ore as well as the water chemistry and mill operating conditions. The paper describes the influence of the microstructure of the alloy on the wear resistance and the influence of the chrome content on the pulp chemistry and downstream processing. It also provides information about the in-house tools which Magotteaux have developed to predict the media wear rate with different chromium content alloys and predict their flotation efficiencies that can be expected when the right alloy is selected for a particular application."

Jan 1, 2014

By Leena Vesa, Antti Remes

Design of thickeners is based on laboratory test work, characterizing the material and determining the optimal reagents, dosages and settling regimes. Several methods for dimensioning plant scale equipment exist. Kynch and Talmage-Fitch design procedures has been applied widely for a long time. Nowadays, besides them, a dynamic laboratory test work is applied for design of high rate thickeners. In that the laboratory unit is operated with known solids load per area, feed and flocculation conditions and with raking of the underflow. All these test methods afford useful data for setting up and calibrating a dynamic simulation model of a plant scale thickener. This paper presents a flocculation kinetics based dynamic thickener simulation model and a procedure to calibrate the model parameters. With the model, the underflow stream composition can be simulated over time as a function of the thickener operating parameters, which are: the feed rate and composition, underflow pumping rate, flocculant dosage and dilution of the feed. In addition, the model incorporates calculation of the slurry bed level, the cone pressure, the yield stress and the rake torque. Such a dynamic modeling scheme enables setting up simulation aided operator trainings and developing and testing of advanced control strategies, for example. The unit model can be integrated as a part of concentrator-wide flow sheet simulation model as well. Here, calibration of the kinetic flocculation model based on a laboratory test case data and further the operation of a simulated plant scale thickener are presented.

Jan 1, 2014

By Khoi Nguyen, Luke Keeney

"Hardness" is an important yet diverse material physical property and is a key parameter in the mining industry in fields such as comminution, geotechnical and blast modelling. Several laboratory and field based measurement techniques exist to measure hardness (e.g. Point Load Testing, Vickers, Brinell, A*b, BMWi, UCS), all are designed for specific applications. Current tests are generally destructive and require specific sample preparation procedures which results in high cost tests that are not conducted in adequate quantities to map hardness across an ore body. The EQUOtip rebound hardness tester is a device that has been developed for application in ore body hardness domaining within the AMIRA P843 GeMIII Research Project. The rebound hardness test is non-destructive and suitable for application on half and whole diamond drill core. Data acquisition protocols and a data processing software application (EQProcess) have been developed to facilitate routine collection of comparative hardness information. This paper outlines the data acquisition and processing methodology and provides application examples of defining relative hardness domains in different geological deposit styles.

Jan 1, 2014

By Hiroshi Sasaki, Herman D. Mendoza

"The surface-chemical property of nickel slag fiber was modified in aqueous media in order to act as an active and efficient collector of colloidal amorphous silica from geothermal effluent. Colloidal amorphous silica (0.05 µm) from geothermal wastewater causes operational and ecological problems. It clogs geothermal pipes and waterways, and when disposed to the environment poses hazardous effects on both the flora and fauna ecology. Because colloidal amorphous silica is extremely fine and remains in suspension in aqueous media, conventional solid/liquid processes to remove colloidal silica from its bulk liquid are rendered ineffective.A rapid separation technique is then developed to remove effectively amorphous colloidal silica from its bulk liquid by attaching the extremely fine particles of silica onto a nickel slag fiber coated with magnesium hydroxide, Mg(OH)2. The nickel slag fiber has the following characteristics: a high surface area and predominantly possesses negative charge in aqueous media with an iso-electric point at pH ~2.5. When soaked and saturated with Mg(OH)2 solution, the surface of the nickel slag fiber becomes coated with fine and compacted Mg(OH)2 precipitates. This modifies the surface- chemical property of nickel slag fiber transforming the negatively charged surface into a positively charged surface in aqueous media with an iso-electric point of around pH 11.8, which corresponds to the iso-electric point of Mg(OH)2. When geothermal effluent containing negatively charged colloidal amorphous silica particles (i.e.p. of silica is pH 2) is passed through a column-bed packed with surface-chemically modified nickel slag fibers under natural pH conditions, the colloidal amorphous silica particles are recovered by attachment onto the surface of the surface- modified nickel slag fiber. The recovery of colloidal amorphous silica by attachment is 97-99%, resulting in the production of a relatively clean and silica free output. Aluminum hydroxide, Al(OH)3, was also used to modify the surface –chemical property of the nickel slag fiber. In the same way, it also exhibited a positive response with the collection of colloidal amorphous silica from its bulk liquid, but yielding a lower recovery of 90%. This may be attributed to the lower surface potential and iso-electric point of pH 9.3 for Al(OH)3. The separation process was evaluated and analysed using existing potential energy theories. Figure 1 shows a micrograph of the surface of an unmodified and the Al(OH)3 –modified surface of nickel slag fiber."

Jan 1, 2003

By Michel Brissette, Shaheer Sanuri, Veroljub Mihajlovic

"The main purpose of geometallurgy is to improve the mine planning by mapping hardness and throughput into the mine block model using geostatistics to eliminate the large production fluctuations caused by the ore hardness variability coming from different parts of the pit. However, not all grinding testwork available commercially can be applied to geometallurgy because of large amount of sample required and the associated cost per test. Geometallurgy is now being used in designing grinding mill but as the mining project progress, the accuracy of engineering must improve from 30-35% during the scoping study to 10-15% at the bankable feasibility stage and less than 5% for Engineering Procurement and Construction Management. For SAG milling, the SAG Variability Test (SVT) is an abbreviated version of the standard SAGDesign test developed for this geometallurgical need. The same amount of ore than the original test is ground for three cycles into an open batch SAG test and then the SAG pinion energy is predicted to the standard end point of 80% passing 1.7 mm. For ball milling, a Bond Variability Test (BVT) was also developed using the SAG ground ore from the SVT. The Bond ball mill grindability (Gpb), corresponding to the average of the net grams per revolution from the last three cycles of the Bond test, is also predicted from the third cycle. The relative error for both the predicted SAG ore hardness (WSVT) and Bond Work Index on SAG Variability ground ore (Sv-BVI), in kWh/t, averaged 5.5% and 3.8% respectively compared to the SAGDesign testwork values and are within 7% and 10% respectively from plant benchmark and within 7% from the samples sent to all partner laboratories. Both tests can be continued to measure the true hardness necessary for mill sizing. This article discusses the development of these two new tests, SVT and BVT, their potential use and accuracies in any geometallurgical program."

Jan 1, 2014

By S. A. Bogidaev, M. Yu. Tiunov

"The paper describes the results of the flotation tests with complex rare metal ores from deposits in the Trans-Baikal Territory. Correlations between the quality of produced wolframite, hubnerite and mica concentrates with or without the presence of various alkaline modifiers are determined. Commonly, rare metal ores contain minerals of comparable value to main elements recovered in processing plants using gravitational methods. The paper describes the results of flotation recovery of valuable minerals – main and associated – from gravity tailings of deposits in the Trans-Baikal Territory. It was found that gravity tailings from the first deposit contained fine-grained wolframite, mica (muscovite, lepidolite etc.), feldspar; hubnerite, scheelite, beryl, fluorite, rubidium-containing muscovite from the second deposit, correspondingly. This paper presents the results of the stage flotation tests with the production of tungsten (wolframite, hubnerite), fluorite and mica concentrates from gravity tailings. Figure 1 demonstrates the flowsheet of tungsten ore minerals and mica stage flotation from gravity tailings of the first deposit.Wolframite can be floated using oleic acid with the presence of soda ash, a complexing collector (IM-50), under slightly alkaline conditions in combination with a nonpolar collector [1, 2, 3, 4]. The study included wolframite flotation using the combination of two alkaline modifiers. Flotation of wolframite was performed after pulp desliming, using tall oil saponified with soda ash. The recovery of wolframite in the concentrate of rougher flotation reached 80-85%; the concentrate contained up to 1% of tungsten oxide that can be upgraded to a saleable product using gravitational methods. This procedure was tested during flotation of wolframite, tantalite-columbite and pyrochlore, and provided high performance regardless of a season, at pulp temperatures of 8-10°C, though fattyacid collectors are significantly inefficient at such low temperatures due to low solubility, dispersion and increased collector consumption, consequently. The introduction of two alkaline modifiers in pulp appears to improve these characteristics.The first stage of the tests was focused on increase of iron-bearing tungsten ore minerals recovery from gravity tailings and stabilization of the cold pulp flotation process."

Jan 1, 2018

By S. P. Das

Tumbling mill is an important unit operation in a mineral processing industry whose operation needs to be understood to make it an energy efficient unit. One of the important mill parameters is the impact spectra generated by collision of the moving charge mass on the mill shell. This process also generates mechanical vibration on the mill shell and propagates to the plumber block of the mill. In this work, we tried to understand the impact spectra by using different minerals such as Banded Hematite Quartzite (BHQ), Hematite and Quartz as mill feed of a semi-autogenous (SAG) mill. The said mill is of 1000 mm diameter and fitted with a force sensor on the mill shell and a vibration sensor on the plumber block. The analysis of the impact spectra was done by taking into consideration the peak impact force above a certain threshold value. It clearly shows that the impact force decreases as the particle size become finer irrespective of the mill feed material. This can be used as an effective tool by the mill operators to have an understanding of the mill product size reduction. The mechanical vibration tapped by a tri-axial accelerometer was analyzed by power spectral density analysis. The vibration signal analysis shows the variation in the power spectrum magnitude both at lower and higher frequency. It also shows inconsistency in case of BHQ where it shows a significant decrease in vibration at lower frequency and increase in vibration at higher frequency. Therefore, the impact spectra analysis is a better method compared to vibration analysis in understanding the mill product size reduction.

Sep 1, 2012

By A. Bastrzyk

Text The mining and refining of minerals generates large amounts of solid waste. The waste from cleaning operations constitutes up to 90% of the total production. Although some of them can be used in mining, civil enegineering, construction, agriculture, most of them must be disposed in dumps and slurry ponds, causing major economic and enviromental problems (Alonso, 2002; Alon-so, 1999). The refuse from minerals cleaning may have considerable valuable particles content, which can be used in industry. Thus, the recovery of these particles from minerals waste by using a cleaning method effective at fine particle size, may overcome these consequences. Surfactants are used in numerous applications including emulsification and solid surface modification. In the oil agglomeration of minerals, the ionic surfactants (both anionic and cationic) are used for the hydrophobization of mineral surface and the oil-water emulsion preparation. When the cationic surfactant is injected into the oil-water mixture, surfactant molecules adsorb at the oil-water interface, changing droplets? properties. The addition of anionic surfactant to the mineral suspension was found to modify the solid-liquid interface. In this paper, the condition and mechanism of selective separation of magnesite from quartz are presented. A satisfactory was achieved with the amount of anionic collector (sodium oleate) equal to 15.2 mg/gsolid and with the amount of cationic collector 27.9 mg/gsolid for cetyltrimethylammonium bromide (CTAB) and 16.9 mg/gsolid for dodecyloammonium hydrochloride (DDAHCl) at pH 8. At these conditions, the amount of agglomerated carbonates was about 12% for CTAB and 5% for DDAHCl.

Jan 1, 2014

By Graeme Lane, Yuqing Feng, Kaixi Jiang, Junwu Zhou, Zhengchang Shen, Tao Song

"Airlift reactors are used in a wide range of industries, such as hydrometallurgy, biochemical processes, chemical process industry and waste water treatment. With increasing superficial gas velocity three circulation regimes can be defined: no gas bubbles in the downcomer, gas bubbles remain stationary in the downcomer and gas bubbles in the circulating regime. In this paper a numerical modelling method was presented for gas-liquid flow in airlift reactors under different bubble recirculation regimes. Gas-liquid flow was modelled using the Eulerian two-fluid equations, and extra user defined subroutines were incorporated to consider the complex physics, such as bubble induced turbulence and turbulent dispersion force. Some alternative correlations of drag coefficient were used to capture the bubble distributions in the riser and downcomer of the airlift reactor, with consideration of the interaction between bubbles. As using constant bubble size is hard to describe global characteristics of the flow in airlift reactors for three circulation regimes, a model including multiple bubble sizes was presented to get more accurate simulation results of gas holdup and water velocity. Also, the inhomogeneous MUSIG model was used, as an exploration, to compute the complex flow regimes. The MUSIG model is a population balance method to predict the bubble sizes, taking break-up and coalescence into account. The modelling method was applied to a laboratory internal loop airlift reactor, and the simulation results were compared with the experimental measurements of Simcik et al. (2011) for gas holdup and water velocity. The three bubble circulation regimes were observed from simulation figures. Reasonable agreement was obtained over a range of operating conditions, and an improvement was demonstrated using the proposed methods."

Jan 1, 2014