Search Documents

By K. B. Venkatesh

In view of the importance of size reduction operations from the energy consumption point of view, during the past one hundred and fifty years a number of attempts have been made to develop a general energy-size relationship. However, to date it has not been possible to clearly define the scope of application of various laws proposed, though Bond law has been widely used with a moderate degree of success. It was, therefore, decided to carry out a thorough analysis of the batch ball mill grinding data available in the literature on several minerals that were ground under normal range of operating conditions. In particular, relationships proposed by Bond, Kapur, Voller and Morrell were examined in detail. It was found that the relationship proposed by Kapur in terms of the mean particle size provided a more accurate basis for estimation of energy. The value of the exponent of mean particle size in this relationship, a, is same as the exponent of the particle size in the expression for the grinding rate parameter: ki = Axia, provided the particle size distribution range corresponds to the self-similar or self-preserving regime. In this regime, mean particle size is proportional to the 80 percent passing size and size modulus. From the practical application point of view, it was possible to describe the variation of µ1 over limited, but significantly broad size range, using a constant value of a. Thus, by carrying out a few batches, grinding experiments over the size distribution range corresponding to the contents of the production mill, the applicable value of a can be determined. Keywords: energy-size relationship, ball mill, mean particle size, self-similar size distribution regime

Sep 1, 2012

By A. Morrison, P. Brito-Parada

"The separation of valuable and gangue minerals according to their surface hydrophobicity in a froth flotation tank occurs in both its pulp and froth phases. In the pulp phase, hydrophobic particles must be brought into contact with rising bubbles introduced at or near the bottom of the tank. In a mechanical froth flotation tank, this is primarily achieved through the agitation of the pulp by an impeller or by a rotor-stator system. However, the turbulent and mixing effects of such an impeller or rotor-stator system, necessary to promote bubble-particle interactions in the pulp, are not confined to the pulp zone, but are transmitted into the froth zone at the pulp-froth interface. This impeller-induced turbulence at the pulp-froth interface is compounded by the impulse of buoyant bubbles entering the base of the froth phase, reducing the stability, and thus separation performance, of the resulting froth. Hence, turbulence improves separation performance if it occurs deep in the pulp phase, but diminishes it if it occurs close to the pulp-froth interface. For this work, a performance-enhancing pulp phase insert was designed to isolate the impeller-induced turbulence from the pulp-froth interface in a laboratory-scale, continuously-operated froth flotation tank. The result was a shifted grade-recovery curve that allows the insert to be designed to maximize the recovery from the system without sacrificing the grade of the concentrate, or vice versa, along a spectrum of improved performance. This paper will present the insert design and development process that resulted in this improved grade-recovery curve, as well as a set of heuristics that could be used to design a similar insert for pilotand industrial-scale validation and deployment.INTRODUCTIONAn almost ubiquitous design feature of commercial flotation tanks is the enclosure of the impeller to create a concentrated turbulent zone (Mavros, 1992). These turbulent zone enclosures are varied-- from the rotor-stator design of, for instance, Outotec cells, to the air disperser design of Wemco cells-- but all share the same rationale: that turbulence is desirable to promote bubble-particle interactions (Ralston, 1999), and to produce smaller bubbles (Wills, 2006), but also undesirable because it promotes the detachment of valuable mineral particles from bubbles, and exacerbates entrainment-inducing mixing at the pulp-froth interface (Jameson, 2010)."

Jan 1, 2018

By Z. He

Based on full investigation of the characteristic of sphalerite in the residue obtained from cyanidation leaching process and the study of the mechanism of the interaction between flotation reagents and sphalerite with the aid of electrochemical analysis, the reagent named YO was developed for eliminating the depression effect of CN- on sphalerite and reducing the dosage of CuSO4. The achievements have been used in commercial production for the treatment of the cyanidation residue to recover the zinc minerals, obtaining a zinc concentrate with grade of 56.49% Zn and recovery of 86.63% Zn.

Jan 1, 2014

By C. Eswaraiah

A drop weight tester (DWT) is designed and fabricated for the purpose of analyzing single particle impact breakage characteristics of different ores. The test results were evaluated through the breakage distributions of different size fractions at five different input energy levels. The breakage parameter, t10 (Narayanan, 1986) is used to represent the degree of size reduction, which is assumed to be representative of the breakage product size distribution obtained from single particle breakage. Representation of breakage distribution with this method consist one more breakage dependent parameter (a). To evaluate the impact breakage characteristic of different ores, a mathematical relationship was established to analyze the dependency of breakage parameters, t10 and a on specific input energy (EIS) or fracture energy (Tavares et al, 1998, Fandrich, 1998), specimen size (?) and Bond?s operating work index (WI0). Mathematical results developed gives adequate model for all ball mill modeling. It can be concluded that the drop weight test method is a useful and practical way of evaluating the impact strengths of various ores and results of which can be used in modeling mills.

Sep 1, 2012

By S. K. Dutta

Enormous amount of iron ore fines is generated, due to partly soft and friable nature, during mining. Coal fines are also produced during their processing. These fines cannot be used directly in ironmaking reactors. Utilization of these fines for extracting metal is of vital concern for resource conservation and pollution control, and therefore, a novel concept of agglomeration by cold-bonding is developed. Composite briquettes/pellets of iron ore fines with coal fines were prepared in the laboratory by cold-bonding technique. Various binders such as lime, Ca(OH)2, slaked lime, dextrin, molasses, fly ash etc were employed either alone or in combination in different proportions for making composite briquettes/pellets. It was possible to obtain dry strength of composite briquettes more than 300 N/briquette in some cases and more than 200 N/briquette in many trials. The combination of fly ash with slaked lime and molasses produced the highest strength, more than 400 N/briquette. Drop strength and shatter index values of composite briquettes/pellets were also measured. In briquettes, best compressive strength (978 N/briquette) is observed by using polyvinyl alcohol (PVA) binder. In pellet, best compressive strength (362 N/pellet) is achieved by PVA; shatter index (0.1%) and dry drop strength (158 numbers) are also good. Compressive strength above 200 N/pellet is obtained by fly ash, slaked lime and molasses combination.

Sep 1, 2012

By K. W. Stöckelhuber, A. Wenger, H. J. Schulze

"An important elementary step of the flotation process is the forming, drainage and rupture of a thin intervening liquid film between bubble and mineral particle.After the encounter of the bubble with the solid surface a wetting film is formed. The initial thinning of this film is driven by the capillary pressure inside the bubble. When the film has reached a certain thickness rupture can take place.There are two possible mechanisms describing this process:-, Growing fluctuation waves (spinodal dewetting) on fluid interfaces under the influence of any kind of attractive forces (electrostatic, van der Waals). -, Nucleation inside the film.Metastable wetting films on negatively charged, hydrophobic glass surfaces (gaseous phase methylated), or on hydrophilic, positively charged glass surfaces (with Al3+ ions), have been analysed by means of the kinetics of film thinning according to the Reynolds law. These experiments demonstrate that both mechanisms can be responsible for the rupture of a thin wetting film. In the case of hydrophobic surfaces the nucleation mechanism is preferred; in the case of opposite charged silica surface the capillary waves mechanism due to an attractive electrostatic double layer force between silica and air bubble takes place.Hereby the existence of a long range hydrophobic force. on a hydrophobic surface can be excluded. The apparent interaction can be explained by the presence of gas nuclei formed on heterogeneous surface sites. The results provide deeper insight into the mechanisms of wetting film stability, adhesion process in flotation and droplet coalescence."

Jan 1, 2003

By Ingvar Ymén, Alexandra Lundmark

"The depressive effect of dichromate on galena was evaluated with chemical experiments and small-scale depression experiments at a pH of around 12. The depressive effect was measured with Dynamic Vapor Sorption (DVS), which measures the water uptake of a sample as a function of the % relative humidity. The depression is due to PbCrO4PbO, which in the presence of Ca2+ and SO4 2- forms a more or less amorphous solid solution (Pb,Ca)(CrO4,SO4)PbO, which clogs to the surfaces of the ore. Free Pb2+- ions are needed for depression to occur and at high pH Pb2+ - hydroxide complexes, supply enough Pb2+ - ions to precipitate (Pb,Ca)(CrO4,SO4)PbO. In air CO2, precipitates CaCO3 which slowly lowers pH, precipitating more (Pb,Ca)(CrO4,SO4)PbO and CaCO3 on galena. Similar experiments where performed with five alternative depressors whereof phosphate, which forms an amorphous precipitate of approximate composition Pb3Ca13(PO4)10SO4, gave the best results. Phosphate was tested in laboratory scale flotation experiments giving encouraging results.INTRODUCTIONWithin Boliden Mines, concentrating of copper and lead from complex sulfide ores is performed by bulk flotation, meaning that copper and lead are concentrated in the same product. Downstream, copper and lead are separated by flotation of chalcopyrite, and depression of galena. Boliden has for many decades used sodium dichromate to depress galena (reference 1). Dichromate is both toxic and carcinogenic and Boliden has for many years investigated several alternatives. So far, however, the best results have been obtained with dichromate. Since Boliden has tried to substitute dichromate for a long time without finding a process as effective, Boliden decided to clarify the function of dichromate in the depression of galena and on the basis of the outcome find alternative depressors with similar function. This study was given to RISE Bioscience and Materials / Surface, Process and Formulation as a consultancy assignment. This paper presents the outcome of the combined efforts of Boliden and RISE."

Jan 1, 2018

By X. H. Zhou

Column flotation is being widely adopted for fine particle treatment by the mineral processing industry due to its simplicity of structure, high efficiency and good separation performance. Cyclonic static micro-bubble column flotation (FCSMC) is an innovative column separation technology that has been successfully applied in the coal preparation industry in China. Recently, the application of this equipment has been further expanded to the separation of several minerals such as fluorite, copper, iron, etc. The bottom of the FCSMC is a cone in which cyclonic field is generated when circulating pump is injected tangentially into the column. The unique cyclonic structure is believed to help enhance the column separation performance. Since the FCSMC is a new flotation device, little work has been done to understand the fundamentals of this technology. In this research, a computational fluid dynamics software, ANSYS/ FLOTRAN, was employed to simulate the flow field of a lab FCSMC system (F0.2 m, F3.0 m by length.) The distribution patterns for velocity field and flow field were investigated under single phase condition. It has been found that axial velocity of the slurry decreases and becomes stable along the height of the column from bottom to top, and the slurry performs as a descending flow pattern. Another observation is the velocity fluctuates vigorously near the wall due to wall effect. Compared to axial velocity, the radial velocity distribution is smaller and more complicated. The basic pattern is that on a given cross section of the column radial velocity increases from the wall to the center and it the velocity changes greatly around the center. Under the condition of column height less than 0.8 m, the axial velocity is negative and it directs from the wall to the column axis. When column height is higher than 0.8 m a reverse pattern is obtained, i.e., axial velocity is positive while directing from column axis to the wall. Special efforts were directed to investigate the tangential velocity pattern. Results indicate that the tangential velocity patterns of different cross sections are similar and showed a symmetrical distribution. Tangential velocity distribution concluded two zones: outer whirlpool and inner whirl-pool. And, interestingly, it has been found that on different cross sections the highest tangential velocity always occurs at the same position of the cross sections.

Jan 1, 2014

By Julian Dimitrov, Kremena Dedelyanova

"The paper presents research on hydrodynamic processes occurring at the elementary act of flotation. Discussed existing models to determine the effectiveness of conflict of bubbles with particles in vibration column flotation machine. The paper presents a disperser for a column flotation machine, in which the dispersion of the gas phase is carried out using vertical vibration with defined frequency and amplitude. The paper presents research of mechanism for the creation of air bubbles in vibratory column flotation machine. The factors influencing the increase in the duration of the bubble in the area of contact with the mineral particles are discussed. Research was carried out on the effect of frequency and amplitude of vibrations on speed of precipitation of mineral grains of different density. Formulas are derived for the parameter effect of vibrations, applicable to the design of flotation machine. The collision efficiency of the bubbles in vibratory column flotation machine is determined. The vibrations of the hydrated layer allow for cost-effective implementation of the elementary act of flotation by providing larger relative velocities at the contact point between the bubble and the solid phase. It is proposed to complement the model more accurate representation the mechanism of attachment of the particles to the bubble."

Jan 1, 2014

By R. Roufail

In this paper, the effect of different operating parameters of high speed stirred mill on the particle breakage mode is addressed. Morphological features of broken particles is investigated and related to the types of forces generated in the mill using Discrete Element Method (DEM). The stress intensities generated in the mill are varied by changing the agitator speed. The investigated agitator speeds were 1000, 1500, and 2000 revolution per minute (rpm). The minerals considered in this study are hard minerals (quartz) and soft, sulphide minerals (galena). The morphological features examined are roughness, roundness and elongation, which shed light on the mode of breakage during the grinding process. Particles that are rough, less round and elongated would imply that they broke via fracture, along their grain boundaries. On the other hand, the smooth, less elongated particles would mean breakage occurred across the grain, which is abrasion mod. DEM study complemented the understanding of particle breakage mechanism via tracking the types of forces applied on the particles. Normal forces imply compressive loading, which is presumed to impose fracture breakage along the grain boundaries, whereas tangential forces imply abrasion loading. Stirred mill grinding has been regarded as an attrition/abrasion process, whereas, this study showed that about 60% of total particles that are morphologically analyzed for both minerals were rough particles. Such an observation indicates that the fine product, which contain a significant amount of progeny from the coarse fractions are consistently broken via fracture. The morphology results agreed with the DEM findings, which indicated that the agitator speed, mineral type, and residence time would dictate the type and mode of particle breakage. Keywords: DEM, high speed stirred mill

Sep 1, 2012

By Ji Hoe Kwon

Hindered-settling column process has been used for the separation of mineral particles for many years. In this study, a model based on DEM (Discrete Element Method) was used to simulate the movements of particles in a settling column separation process. DEM model is capable of describing the motion of particles and calculating the impact forces between particle and particle, and particle and wall contact under various operating conditions. Drag force, rotation induced Magnus lift force, contact force and the gravitational force acting on individual particles were considered for establishing the mathematic models. The overall motion of the particles in water is satisfactorily simulated by the DEM, and the result shows good agreements with the result of lap-scale experiment.

Jan 1, 2014

By Montaser S. EL Salmawy, Takahide Wakamatsu, Eishi Kusaka

"In conventional flotation, fluoride ions selectively would react with the aluminum site on the microcline surface and produce negative charged sites for amine to be adsorbed (Smith, 1976). According to this view, aluminum site is considered as a key feature in feldspar flotation. Generally, fluoride ion has been widely used as a modifying agent in silicate flotation. Since O'Meara's patent appeared on HF -amine reagent system to selectively float feldspar from quartz in 1942, relatively few contributions have been devoted in this issue. The reason might be that the process works very well, and accordingly there is no initiative to investigate in this area. However, due to the awareness of international community to restrict using of hazardous reagents like HF, sound engineering practice to search for alternative methods, not utilizing HF, has been launched. Inspection of literature, one can find several works dealing with this issue.In this contribution, the effect of ethoxylation of long chain alcohols on the quartz and feldspar flotation behaviors was investigated for surfactants of the octylphenol polyoxyethylene family. The tests were carried out with an average of 7.5 (Triton X 114), 9.5 (Triton X 100), 30 (Triton X305), 40 (Triton X 405) and 70 (TritonX 705) oxyethylene units. Electrokinetic and flotation studies on quartz have shown that at low pH values, quartz could be floated with polyoxyethylene octytlphenols. The possible mode of adsorption of these nonionic surfactants may be suggested to be due to hydrogen bonding between the oxygen of ether and hydrogen in the free hydroxyl groups on quartz surface. It was anticipated that the selectivity between quartz and microcline would decrease as oxyethylenic chain length increases."

Jan 1, 2003

By B. Courtaud

Uranium plants are generally located quite far from conversion plants, resulting in high transport costs. One way of reducing such costs involves putting more uranium in each drum by increasing the final product?s bulk density, which can be achieved via mechanical compaction of the powder and/or improved precipitation. For most of its plants, AREVA has adopted the latter approach, involving a new precipitation process applicable to all kinds of yellowcake produced (via uranates, uranium peroxide, etc.) that achieves bulk density of 3 for soda uranate, for example, instead of the 1.5-2 density available via conventional processes. At present, this process is being undertaken on an industrial scale and will become the norm for precipitation processes at all AREVA U plants. In addition to producing dense yellowcake, the process also delivers a product with no fines, a spherical particle shape (which allows for high-quality powder flow) and superior post-precipitation filterability

Sep 1, 2012

By A. Ghadyani

This investigation was undertaken to assess the possibility of ash and sulfur removal by microbial action of high sulfur-content coal. Thiobacillus ferrooxidans and Thiobacillus thiooxidans have been used for biodesulfurization of coal. Feed samples were provided from Tabas coal mine located in Yazd province, Iran. The sample contained 28.80% ash and 2.30% sulfur. Flotation tests were implemented to optimize the effective parameters in these cells which were constant during bio-flotation tests. According to the results, obtained from various tests using Taguchi orthogonal array design (L27), the values of optimized parameters were pH at 7, 1000 g/t gas oil as a collector, 10% solid content, 15 min conditioning time, 100 g/t MIBC as a frother and 800 rev/min rotor speed. Bio-flotation tests are carried out by means of laboratory double discharge cell and mesophilic bacteria as depressant reagent using above mentioned optimized parameters. The bio-flotation experiments were conducted based on a Taguchi orthogonal array design (L9) with four variables (bacteria type, bacteria count, rotor speed of mixer and bio-conditioning time). The collected data was analyzed by using DX7.0, Minitab14.0 and WinRobust1.02 softwares for evaluation the effect of each parameter on the optimization criteria. Considering the highest combustible recovery and the lowest ash and sulfur content, the value of optimized bacteria type, bacteria count, rotor speed of mixer and bio-conditioning time were Thiobacillus ferrooxidans, 5×107 cells/g(coal), 100 rev/min and 20 min respectively. Under this condition, ash and sulfur content and combustible recovery were predicted 12.39%, 2.08% and 82.03% respectively.

Sep 1, 2012

By Q. Zhang

The flotation behavior of jamesonite was investigated with ethyl xanthate as a collector. It has been shown that jamesonite has good floatability from pH 2 to pH 12, and relatively poor floata-bility at pH>12. The flotation of jamesonite was also dependent on pulp potential at certain pH val-ues. The potential-pH range for jamesonite flotation was established. The FTIR spectroscopy analy-sis and XPS measurement showed that the major adsorption product of ethyl xanthate on jamesonite was lead ethyl xanthate and antimony ethyl xanthate. The intensity of the FTIR signals of metal ethyl xanthate adsorbed on jamesonite and the flotation response of jamesonite were correlated with pulp potentials.

Jan 1, 2014

By Sanjeeva Latchireddi

The effective utilization of the energy in comminution devices depend on how efficiently the broken particles leave the breakage field as soon as they reach product size. In crushers the transport of broken particles smaller than CSS is done by gravity (vertical) thus allowing the energy to be applied to new particles. However, in AG/SAG mills, gravity becomes the energy field and the transport of particles is horizontal which needs a suitable discharge mechanism and has been found to have significant effect on grinding efficiency. The material transport in AG/SAG mills depend on how efficiently the discharge system (grate and pulp lifters) operates. Material transport plays a significant role on efficiency of horizontal grinding mills ? AG/SAG/Ball mills. The magnitude of benefits that can be achieved with efficient material transport in AG/SAG mills has been demonstrated in a Greenfield milling operation at Mirabela Mineração?s SantaRita Nickel operation located in northeastern part of Bahia in Brazil. This grinding circuit was commissioned in October 2009, which was designed as a typical SABC circuit to grind 4.6 mtpa (575tph) to produce a P80 of 125um with 10-12% ball charge in SAG mill. However, it has been operating as ABC circuit without any grinding media in SAG mill. The nameplate design capacity has been achieved in few days and has gradually increased to an average of +800 tph and still it is operating in ABC mode. The milling circuit commissioning resulted in small and relatively simple measures to rectify, which was reflected in the rapid commissioning of the milling circuit and it achieved the nameplate capacity within days. The Santa Rita grinding circuit consists of one 30?x 15.4? 8.5MW SAG Mill fitted with Outotec patented Turbo Pulp Lifters (TPL TM ) in close circuit with HP400 short head pebble crusher and one 20? x 28.4? 5.5MW Ball Mill in closed circuit with Warman cyclone cluster fitted with 10 x 26? CAVEX cyclones. This paper examines the comminution design process, operating philosophies, experiences, post commissioning optimization, and future development works. Evaluation of the milling circuit performance relative to the design criteria is also discussed. Keywords: Autogenous Grate (AG), Semi-Autogenous Grate (SAG, Turbo Pulp Lifter (TPL)

Sep 1, 2012

By S. Castro

The aim of the present paper is to review the current technologies for arsenic removal in the copper metallurgical industry, and to show the progress made with some promising emerging strategies, involving the pre-treatment of copper-arsenic concentrates by selective flotation or by alkaline leaching with Na2S-NaOH solutions. The advantages of alkaline leaching are the selective dissolution of arsenic and antimony, the high extraction yield, and the practically nil loss of copper, which remains in the clean copper concentrate as a CuS residue. Alkaline ?cured? ? a procedure similar to ?acid-cured? in conventional leaching ? improves arsenic extraction and reagent consumption, making this an interesting technology for the treatment of high As-Sb concentrates. In light of recent advances on the selective flotation of enargite and tennantite, the importance of redox conditions to control the flotation/depression of enargite-tennantite from copper sulfides has been well established. However, problems of selectivity must still be solved. Additionally, the limitation imposed in some cases by the need to recover the molybdenum by-product must be considered. The application of selective flotation to obtain a high-arsenic or ?dirty? concentrate and its sub-sequent treatment by the alkaline leaching process is suggested.

Jan 1, 2014

By T. Saastamoinen, N. Heino

"The Olserum deposit located in Sweden hosts an indicated mineral resource of 4.5 million tonnes over 0.6 % TREO, exhibiting a relatively high proportion of HREE. Beneficiation of a composite drill core sample was studied in the flowsheet of magnetic separation of magnetite followed by REE minerals flotation. Primary testwork was performed to select an effective REE mineral collector and then the parameters of grinding size, collector and depressant dosages, slurry pH and density, conditioning time and temperature, and flotation time were tested for optimization of REE flotation. The studies of process mineralogy showed that the REE-bearing minerals monazite, xenotime and apatite were successfully enriched from the concentrations of 0.6%, 0.31% and 2.6% in the feed to those of 17.0%, 8.9% and 65.0% in the concentrate with the recoveries of 79.0%, 81.3% and 71.0%, respectively. INTRODUCTION The Olserum deposit located in Sweden comprises lower grade placer material with higher grade apatite-magnetite veins and hosts an indicated mineral resource of 4.5 million tonnes at 0.6% TREO, with 34% of that being HREO (EURARE, 2017). The mineralization was studied by Andersson et al. (2018). At early stage, high-temperature REE is characterized by abundant monazite-(Ce) and xenotime-(Y) coexisting with fluorapatite and subordinate amounts of (Y,REE,U,Fe)-(Nb,Ta) oxides. During a subsequent stage, allanite-(Ce) and ferriallanite-(Ce) formed locally, partly resulting from the breakdown of primary monazite-(Ce). Alteration of allanite-(Ce) or ferriallanite-(Ce) to bastnäsite-(Ce) and minor synchysite-(Ce) at lower temperatures represents the latest stage of REE mineral formation. The mineralogy and beneficiation were firstly studied by GTK Mintec in the EURARE project for a composite drill core sample. The Olserum is considerably smaller than the Norra Kärr deposit. However, REE are hosted by xenotime and monazite, both of which have well established processing pathways, and meanwhile, the Olserum has a high contribution of the high value critical REE (dysprosium (Dy), yttrium (Y), neodymium (Nd) and terbium (Tb)), which provide a unique advantage for its exploration (Tasman Metals Ltd., 2013). In this paper, flotation of the REE minerals in the Olserum ore was studied."

Jan 1, 2018

By H. R. Manouchehri

The importance of the grinding environment and its effect on sulphide minerals flotation behavior has been known for many years. The grinding environment may play a role in controlling fine and coarse particle flotation along with dissociation of different chemical species in grinding environment. Dissociation of different chemical species and ions within the process water may result from changing the grinding environment. The mining and mineral processing industry undertakes activities that may impact on water resources. These include use and storage of chemical storm-water management, process water management, mine dewatering and management of tailings. In mineral flotation understanding and controlling water quality is paramount important not only because of its effect on flotation but also with respect to control the quality of the water which is released to the environment. Releasing of different anionic and/or cationic chemical species in the process water results from the interactions among different mineral within the ore, process water, and the milling environment. In fact grinding mill acts as an electrochemical reactor which affects the flotation performances of different value minerals as well as the quality of the tailing products. An increasing in antimony content in process/discharge water at Boliden?s Tara processing plant in Ireland to above limitation level was reported in April 2010 which needed to be controlled. An increase up to 6 times of the permitted level was reported which needed an immediate action to control due to environmental considerations. Therefore attempts were made to detect why this higher amount of Sb is released and how to control and minimize its release to the process/reclaim water. This paper discusses how/why Sb content in process/reclaim water was increased by changing the mill electrochemistry and the strategies were taken into considerations to control it. Different strategies, including electrochemical controlling of the milling section, Fenton process, using Bauxsol in treating the process water, etc., have been considered and tested which are described herein. All strategies taken into consideration for solving the problem were successful which indicated good understanding of the issue and good decision making. Furthermore, for each solution the capital and operational costs were roughly estimated. Accordingly, the Sb content in process/discharge water was controlled to a value lower than allowed limitation, i.e., 1 ppm. Keywords: antimony, water contamination, mill electrochemistry, ag milling, grinding media, eh-ph, sulfide minerals, fenton process, bauxsol, lime addition

Sep 1, 2012

By Gus Van Weert, Samuel A. Bolorunduro, David B. Dreisinger

"Silver is currently lost as jarosite during the pressure oxidation of sulphides and cyanidation of the residues yields 5-10% of silver. Efforts to recover silver from complex sulphides, which contain economic fractions of silver require an understanding of the behaviour of acanthite during pressure oxidation. However, previous studies of acanthite (Ag2S) reaction have been complicated by the formation of argento-jarosite and uncertainties arise on the interpretation of the results.In this work, the acid pressure oxidation of high-grade natural silver sulphide mineral (acanthite) was carried out at 110-150°C and under the conditions similar to that of pressure oxidation of complex sulphide. The predominant product of reaction is elemental sulphur. The rate of reaction increases with increasing temperature and with the presence of ferric ions. The kinetics is controlled by chemical reaction with activation energy of 72.6 kJ/mol. The rate of reaction decreases with the presence of silver sulphate in the initial slurry. The proposed overall reaction is close to: []"

Jan 1, 2003