Search Documents

By S. H. Morar

Froth flotation is a physico-chemical separation process that takes place in two phases; pulp and froth phase. It is widely recognised as a complex process, due to the range of interactions present within the system. Of critical importance is the role of the froth phase within the system. The pulp kinetics governs the maximum potential recovery within a flotation cell, while the froth phase governs the selectivity via the froth?s stability. Higher froth stability improves recovery at the expense of grade, and lower froth stability improves selectivity. It is well known that the two major factors affecting froth stability are attached particles and solution chemistry. This paper looks at a flotation bank at different froth depth and frother concentrations. The air recovery to the concentrate is determined at each condition and relates the effect of the operating conditions on froth stability and transport to the amount of solids that are recovered to the froth and concentrate by true flotation. The results presented show that, for a given process objective, which in this case was a consistent mass pull profile, depending on the operating conditions, solids recovery in the pulp is affected by the air rate required to maintain the target mass pull. To a smaller extent, the changes in the pulp composition affect down-stream pulp recovery. The variation in solids recovered into the froth drives the froth stability at the start of the flotation bank, while the frother drives the froth stability at the end of the bank. The performance in between these two extreme conditions arises from an interaction of these two effects. The consequences of these interactions can give rise to counter-intuitive responses that can confound efforts to optimise the performance of the bank.

Jan 1, 2014

By X. Tan

In this paper, the application of the metallurgical residue produced from oceanic cobalt-rich crusts leaching process is studied in the area of wastewater treatment. The modification of the sulfuric acid leached residue and the adsorption behavior behaviour of heavy metal ions such as (Pb(II), Cu(II), Zn(II), Cd(II), Ni(II), Mn(II), Co(II), As(III)) in the waste-water on the surface of the residue are investigated. The rate of adsorption efficiency of heavy metal ions in the wastewater on the modified sulfuric acid leached residue is investigated. It is showed that when the initial pH value of wastewater containing heavy metal ions including Pb(II), Cu(II), Co(II), Ni(II), Mn(II), Zn(II), Cd(II) and As(III) range from 1.4 to 1.9, with the use of the modified leached residue, As(III) ion can be selectively separated from wastewater, and the separation efficiency can reach 90%~100%. The adsorption efficiency is affected by pH, reaction time, amount of adsorbent and the initial concentration of heavy metal ions in wastewater. The results showed that the optimum pH was natural pH value and the absorption equilibrium time was 2 hours. The adsorption efficiency of heavy metal ions increases with the addition of adsorbent and de- creases with the increase of the initial concentrations of heavy metal ions in wastewater. The heavy metal ions polluted wastewater, of which concentration is about 22.5~793.6 mg/L, can meet the national disposal standard for industrial wastewaters in China very well, after 2 hours treated by 3.75~7.50 g/L modified adsorbent at room temperature. Standard methods were used to investaged investigate the absorption behaviour between abosorbentabsorbent and metal ions in the wastewater. It is concluded that the adsorption behaviour of Co(II), Mn(II) and As(III) ion fits Freundlich iso-therm, while the adsorption behaviour of Pb(II), Cu(II), Zn(II), Cd(II) and Ni(II) ions fits Langmuir isotherm, and the saturated adsorption amount of the modified adsorbent is about 54.0~336.7mg metal/g?adsorbentabsorbent. It is suggested that the modified sulfuric acid leached residue produced from oceanic cobalt-rich crusts is environmentally attractive and meaningful as absorbent used in heavy metal ions polluted wastewater.

Jan 1, 2014

By P. Huang

Chitosan was tested as a depressant in the differential flotation separation of chalcopyrite and galena. The micro-flotation results showed that chitosan selectively depressed chalcopyrite while galena was floated by potassium ethyl xanthate in acidic solutions. With the addition of 0.67 mg/L chitosan (CT) in the slurry of chalcopyrite-galena mixtures at pH 4, the recovery of galena was 95% while that of chalcopyrite was 30%, indicating that chitosan could potentially be used in differential Cu-Pb sulfide separation. Furthermore, the study of chitosan with either low (LCT) or high molecular weight (HCT) in the differential flotation indicated that better separation was achieved by the chitosan with lower molecular weight (LCT). ToF-SIMS was employed to study the distribution of CT on the surface of chalcopyrite-galena mixtures by ion mass spectra analysis and surface imaging, which showed that CT adsorbed heavily on chalcopyrite but barely adsorbed on galena. The positive ion ToF-SIMS spectra provided information on the surface composition of chalcopyrite-galena mixtures after CT treatment. It appears that the selective adsorption of CT on chalcopyrite was originated from the strong interaction between NH3+ and Cu. Keywords: differential flotation, micro-flotation

Sep 1, 2012

By A. Oberrauner

Electrostatic separation is a dry separation technique usable for many applications in the mining- and recycling industries. At the Chair of Mineral Processing intensified research has been done on this topic during the last years. One challenge was to measure the triboelectric charging of fine mineral particles in a triboelectric charging device consisting of an electrically insulated polyethylene rotor/stator assembly. These tests, performed on monomineralic samples, were accomplished in a climate chamber. It was shown that charging of minerals not only depends on rotor speed, feed rate and atmospheric circumstances but also on the properties of the applied electrostatic field. Tests on pure calcite in contact with the polyethylene rotor/stator system resulted in specific triboelectric charges up to +10 nC/g at low relative humidity. With more water present in the surrounding atmosphere, these charging values decreased significantly. However, at higher relative humidity, triboelectric charge values could be maintained after an electrostatic field of positive polarity was applied. Similarly, charging behavior was found with other hydrophilic minerals. The idea behind all these tests was to find the largest charging difference between minerals occurring together in a deposit and to be able to charge them oppositely, assuming that this means good sort ability in an electrostatic separator. The results gained from these investigations are shown. After having obtained many results on charging pure minerals, it became interesting to test the applicability of the charging tendencies on electrostatic separation of fines <100 µm. In order to do so, a separator for fine polymineralic powders was developed, constructed and combined with the triboelectric charging device, all being set up in a climate chamber. This new so-called coax-separator is presented along with first test-results.

Sep 1, 2012

By B. K. Saikia

A preliminary attempt has been made to study the particle size distribution (PSD) of minerals in one of the industrially important pulverized Indian coal sample using computer-controlled scanning electron microscopy (CCSEM). The results show that clay minerals, quartz, pyrite, and pyrrhotite form the bulk of the mineral matter. Minor minerals, such as calcite, dolomite, ankerite, barite, oxidized pyrrhotite, and gypsum are also observed in the coal sample. The PSD of the included minerals is generally observed to be finer than that of the excluded ones in the coal. Thus, the coal rich in included minerals has more small mineral particles, which may affect its reactivity. The proportion of included to excluded is found to be higher in major cases. Si is found to be mostly occurred as quartz and clay minerals, while Al mostly occurs as silicate minerals. Fe is primarily present as iron sulfides, iron oxide, and Fe-Al-silicate. S is partitioned into iron sulfides and gypsum. Most Ca occurs as carbonates and gypsum, with a minor fraction associated with clay minerals. Mg is found to be mainly present as dolomite and clay minerals, with a very minor fraction present as ankerite. The majority of alkali elements are associated with aluminosilicates. P is mostly associated with kaolinite and/or present as more complex compounds containing Al, Si, and other elements as apatite are found to be absent in the coal studied. Ti is mainly present as rutile and kaolinite. The geo-chemical association of the trace elements has also been discussed. Keywords: minerals, Assam coals, Indian coals, CCSEM study

Sep 1, 2012

By V. Hudecek

Problems of sudden outbursts of rock and gas present in deep mine mining ones of the most complicated interrogation. It is searching for the methods of prediction and prognosis that can be most useful for the government of these phenomena. Till now the pressure and the desorption of gas in bore holes was consider to be the decisive criteria. By the work of authors with using of statistical date was verify that for considerable reliability of forecast and prevent outbursts is necessity investigate characteristics of workplace and other indicators. These indicators were analyzing and assemblage into mathematical dependences which represent active and passive force asserting with in the process of rush. It was validated by using the equations which are presented in the manuscript that the accuracy of pre-diction of the phenomena is higher and methods of preventions are better also.

Jan 1, 2014

By Peter Ay, Harry Pempel, Satya Narra, Mike Müller, Jens Markowski

"Within the next few years major changes in mobility are expected. Increasing numbers of electric powered cars, electrobikes and E-Scooters define the transport sector. Recently lithium based traction batteries as storage medium have led into matrurity of series production combining high electrical efficiencies with low weights and compact dimensions. Due to the relatively young development with lithium batteries utilization, only few investigation were conducted regarding their recycling. Conventional battery recycling processes can not be applied due to differences in design and chemistry. So an automated disassembly and processing procedure for lithium traction batteries has been developed in the R/D-project ""Li-WERT"". Instead of complete smelting of the batteries without pretreatment, an automated disassembly and specific treatment of the material streams was realised, adjusted to the needs of the subsequent recovery technologies. A higher quality, with reduced expenses for the separation of fine-grained or fused material mixes, can be obtained for the individual components. The automated disassembly using an industrial robot significantly reduces dangers for the operating crew. The selective disassembly and beneficiation allows full recovery of the fractions. The batteries will be disassembled to cell level by the industrial robot. Anodes, cathodes, and separation layers are isolated and processed. The technology is designed, that no waste is generated for disposal. The pelletised cathode coating and the other separated metals (stainless steel, copper, aluminum) can be used in respective metallurgical plants. Circuit boards and plug contacts are also coveted secondary raw materials for reuse. The process is modular and offers high flexibility, e. g. for new battery types/ sizes by quick adjustment of the robot and tool change. Adaptation to other cathode materials (e. g. Li[FePO]) is possible. After finishing the R/D-project, a pilot plant for demontage was realised in 2013."

Jan 1, 2014

By Arkady Senchenko

At present, there are different traditional and modern methods for ore grindability evaluation. The correct and rational approach to sampling, testing methods and mill sizing enables one to design a workable technology. This paper contains TOMS institute experience in different grinding indices determination over the last 7 years (SAG Design Test, BWi, CWi, RWi, and other). Mill sizing examples and circuits modeling for the projects in Russia and Kazakhstan are considered. Keywords: ore grindability, SAG Design Test

Sep 1, 2012

By L. Z. Li

The application of some environment-friendly mineral processing technology was introduced in Xitieshan lead?zinc mine and Hugary copper mine of China Western Mining Co., Ltd, located in western plateau area where the ecological environment is extremely fragile. The results of the significant economic efficiency were obtained by applying these new techniques while the protection of peripheral environment and the improvement of ecology were made.

Jan 1, 2014

By Hamid-Reza Manouchehri

"Sustainability calls for maintenance, rational use and enhancement of natural resources as well as balance consideration of ecology, economy, and social justice. The challenges in mining industry call for a sustained global effort using the leverage of available technologies and emerging new technologies. The industry uses significant amount of energy with the highest portion in comminution. To conserve energy, attempts have been made to improve the efficiency of the conventional crushing and grinding equipment. Nevertheless, the new and energy efficient comminution technologies are favorable through a longer term strategy. Since crushers are more energy efficient than mills, it is logic to conduct part of milling, in the crushing stage. After years of research and development, Sandvik introduces a new crushing technology, VibroconeTM, to change traditional crushing concepts. The new crushing device is able to crush and grind particles with a higher reduction ratio, more than two fold, than that of conventional crushers. By implementation of the new technology, a suitable feed size for milling can be provided to conserve energy as well as media and liner consumption, to reduce milling circulating load or increase mill capacity. There are other benefits associated with this machine, one of them being providing a higher surface area. This paper discusses the performance of the machine and its applications for comminuting different ores."

Jan 1, 2014

By R. C. Dunne

As ore grades of existing and new ore deposits continue to decrease there is ever increasing pressure to decrease operating costs to maintain profitabitabitiy at existing mine sites and for new projects. The accepted solution to this dilemma in most cases is to increase treatment rate, leading to a coarser grind, at the expense of marginal decreases in recovery. The recovery loss is usually associated with losses of liberated and composite coarse material. This paper will review the practice of coarse particle flotation, including the reagent chemistry, cell hydrodynamics, froth stability, entrainment and flotation cell design, all parameters important to the recovery of coarse liberated and composite particles. This will provide a better understanding of opportunities to improve the recovery of coarse particles. Some examples will be provided.

Sep 1, 2012

By A. Sand

Within stamp-charged coke making a large volume of coal is compacted to one single coal cake before entering the coke oven chamber. This is done by means of several falling stampers in a stamping machine having a mold nearly of the oven?s dimensions. Producing a high quality coke also from inferior coals requires a cake density of approximately 80% of the coal density. Besides that the industrial stamp-charging process demands a minimum mechanical strength of the coal cake to move it from the stamping mold into the oven chamber without failure. Densification and the build-up of cake strength were investigated earlier in stamping tests using a micro-stamping device. The quantities derived from these tests (as e.g. cake density or porosity) represent average values for the entire cake. Statements describing the local compaction state at different heights are difficult to achieve without destructing the cake. In order to gain better insight into the densification process and the inner structure of the coal cake a computational model based on the discrete element method (DEM) has been set up using 2 and also 3-dimensional simulation software. The stamper?s position and velocity as well as the force acting on the stamper were monitored and the model?s response was compared against measurement data from laboratory stamping tests. It was possible to reproduce the force and displacement pattern of the stamper in response to the viscoelastic properties of the cake using standard DEM bonding and contact models. Furthermore, the rearrangement of particles in response to the compaction by the stamper was tracked by calculating their displacement at the point the stamper hit the coal surface. The latter can also be used as indicators of particle deformation or breakage. By defining control points at different heights the particle displacement, stress and strain rates, porosity could be studied at different heights. Keywords: coke making, coal stamping, compaction, agglomeration, DEM, simulation

Sep 1, 2012

By C. Martinez, S. Helle, M. Pincheira

We studied the feasibility of automated mineralogy to discriminate between tennantite and enargite, the main sulfosalts found in the Rio Blanco deposit, Codelco-Chile, in order to predict the content of minor elements (As, Sb, Ag, Pb, Zn) that impact on the process and concentrate prices. The identification of these minerals is feasible using traditional microscopy, however not possible by automated mineralogy. This drawback prevents comparing the databases generated in the past by means of conventional microscopy with the information obtained at present by QEMSCAN. To differentiate enargite from tennantite the mineral composition of both sulfosalts was studied by electron microprobe. The presence of associated minor element contents of about 8% zinc in tennantites and not exceeding 0.07% in enargites were used to modify the SIP database of QEMSCAN to enable the quantification of these phases in samples of head, residue and concentrate coming from As-bearing domains of the deposits. Detection limits allowed to determine the mineral species in the head, concentrate and residues. The integration of methodologies such as automated mineralogy and microprobe can be used successfully to quantify the presence of some ore forming solid solution.

Jan 1, 2014

Sedimentary deposits such as sandstone are formed by the aggregation of cemented sand grains. Phosphates and laterite present similar aggregation of mineral grains. Grains and cement have different mineralogy and chemical characteristics. During size reduction through crushing or coarse grinding, the rocks are crumbled. Mineral grains and cement are then liberated, and the produced size distribution reflects their ?natural size distribution?. Mathematical modelling of these concomitant effects of crumbling and mineral liberation necessitates a specific material description and the adaptation of the commonly used theories of breakage kinetics and population balance. The coarse particles are mainly agglomerates made of mineral grains and cement particles whereas the fine particles are grains and cement with a natural grain size distribution. The population balance between the different particle size and particle types during size reduction takes into account the breakage rate and the progeny size distribution. The breakage rate can be described by a simple probability function or by a first order kinetics whereas the progeny size distribution is described by a breakage matrix. The model proposed here considers that the agglomerates will produce other agglomerated particles, liberated grains and cement particles; the two latter having their natural size distribution. The liberated grains and cement particles are subject to size reduction and follow the most commonly used theory of breakage. The present paper describes the theoretical approach of the concomitant crumbling and liberation effects. The application to a mathematical model for the cone crusher is presented. The advantage of such approach is then demonstrated through a simulation study for the optimisation of a crushing plant. Keywords: mineral liberation, modelling, crushing, sedimentary ore

Sep 1, 2012

By Darryel Boucher, Raymond Langlois, Neil Rowson, Kristian Waters

The Knelson Concentrator is a centrifugal gravity concentrator composed of a high speed rotating bowl into which a mineral slurry is fed. The rotational motion creates a centrifugal acceleration up to an equivalent of 200 G. Under this acceleration, particles enter fluidised riffles along the side of the bowl, with the fluidisation allowing for the substitution of dense material for less dense. The separation mechanism is not fully understood and questions remain on the optimal residence time, slurry feed parameters and bowl surface profile to achieve a better separation. The positron emission particle tracking (PEPT) technique has been applied to record the motion of a -1700+1180 µm particle of a quartz-gold matrix, labelled with 18F radioisotope while it undergoes concentration inside a 3" laboratory scale Knelson Concentrator (KC-MD3) operated at 60 G. The slurry used was composed of quartz and magnetite. Particle trajectories during the first stage of the concentration process where the heavier particles centrifuge through the increasingly dense slurry towards the riffles of the bowl are shown with respect to time. This work reveals new information on particle motion inside the Knelson Concentrator and the results will be used for validation of developed separation model as well as optimisation of a centrifugal concentrator’s performance.

Jan 1, 2014

By Seoul National University, Ki-Ho Kim, Jong-Pyo Kim, Sung-Min Joo, Hee-Chan Cho, Hyung-Seok Kim

Aragonite was synthesized in addition of Mg2+ ion and SrCO3 seed by carbonation process, and the best condition and mechanism of the synthesis was studied by analysis of continuous pH change, ICP, XRD, and SEM. As MgCl2•6H2O addition increased, aragonite phase increased at condition of CO2 flow rate of 100 mL/min and stirring rate of 250 rpm. It was the dissolution of Mg(OH)2 that determined overall reaction time. As SrCO3 seed addition increased at 0.2 mole MgCl2•6H2O, the amount of aragonite increased and the aspect ratio was from 5 to 9. And it was thought that Mg2+ ion prohibited calcitetransformation of aragonite formed by SrCO3.

Jan 1, 2003

By Vladimir Vigdergauz

"Electrochemical studies of metal sulfides in connection with their floatability are discussed. According Frumkin, sorption of electroneutral organic substances has a maximum near the potential of zero charge. This idea initiated attempts of application of electrochemical methods for the controlling of organic collector sorption and mineral flotation. The lecture reviews results of electrochemical studies of the processes taking place during sulfide flotation: redox-state of mineral surfaces and xanthate solutions, xanthate sorption and hydrophobic layer composition, surface wettability and flotation recovery of sulfide minerals. Redox-transitions of minerals, transport of ions and charging of mineral surfaces, electroreduction of dissolved oxygen and accompanying processes of oxidation of minerals and reagents-collectors, - all these matters became the subjects of detailed research. Cyclic voltammetry, rotating disk electrodes, spectro-electrochemical techniques and other modern experimental methods now routinely accompany studies of mineral processing. Relatively new electroanalytical techniques like the voltammetry of mineral particles immobilised on electrodes using polymeric binders have become extremely useful for studying weakly conductive minerals and dispersed flotation products. Full discussion of electrochemical studies of metal sulfides in relation to mineral processing must include bioelectrochemistry and electrocatalysis which open exceptional possibilities for selective leaching of gold and non-ferrous metals. At this time, the paper focuses on the sulfide flotation as a potential-dependent process; the problem of oxygen and its influence on the sulfide flotation; the electrochemical aspects of xanthate oxidation and sorption; theory of suspended electrodes as applied to the mineral slurries and experimental study of the effect of electrochemical pretreatment of flotation pulps."

Jan 1, 2014

By Aldo Cipriano, Fernando Estrada

The mining industry is in search of control strategies that allow considering a global optimization of their processes, ensuring their stability. This has led to the application of recently developed control techniques on large-scale systems in the mining processes. One of the most important process of the mining industry is the mineral grinding, as the product particle size impacts, in a significant manner, the recovery rate of the valuable mineral in the separation stages. As a solution, a centralized hybrid model predictive control (HMPC) is presented; this control approach maintains the product particle size on a defined range and minimizes energy consumption, maintaining the grinding plant in a stable operation. As a comparison, a conventional model predictive control with an expert system to handle discrete events was developed, showing HMPC is a suitable solution that can used in the grinding process, with the benefit that it handles in the same controller both discrete and continuous dynamics and events.

Jan 1, 2014

By Dingwu Feng, Jannie S. J. van Devente

"The effect of ultrasonication on reactions at solid/liquid interfaces was investigated in two slurry systems, i.e. gold cyanidation and geopolymerisation. The kinetics of gold extraction were significantly enhanced and the cyanide consumption was reduced in the cyanidation of a pyrite concentrate using ultrasonication, probably due to the prevention of leaching passivation, the improvement of the dissolution of the gold host sulphides and the oxidation of soluble sulphides to sulphate. The effectiveness for ultrasonication was improved with the injection of oxygen and the addition of dithiophosphate through enhancing the formation of the oxidation radicals and selectively inducing cavitation bubbles directly at the sulphide interfaces. Ultrasonically enhanced cyanidation could render currently uneconomic deposits viable for extraction by improved cavitation efficiency with the aid of surfactants.Ultrasonication increased the compressive strength of the formed geopolymers through accelerating the dissolution of the Al-Si materials, strengthening the bonds at the solid particle/gel phase interfaces, enhancing the polycondensation process and improving the formation of semi-crystalline to crystalline phases. The use of power ultrasound will yield high-performance geopolymer materials."

Jan 1, 2003

By M. Holuszko, I. Mikhalev

"Previous studies described by Galvin et al. (2017) have shown that for Australian bituminous coal fines, both in batch and in continuous process, the new improved oil agglomeration procedure based on the use of high-internal-phase (HIP) emulsions, as compared to the conventional “pure oil” agglomeration process, enables a significant reduction in the amount of oil while reaching a high yield of clean coal (approximately 90% of agglomerates greater than 355 µm in size) in a significantly shorter time. The HIP emulsion used in these experiments comprised up to 95% vol. aqueous solution of sodium chloride (3% wt. concentration) and for the rest, a mixture of kerosene (oil) and sorbitan monooleate (SMO emulsifier) in a 1:1 ratio as a binder. This study evaluates the applicability of the new HIP-oil agglomeration process to treat Canadian bituminous ultra-fine coal and Russian sub-bituminous coal fines and compares results from agglomeration to the flotation response of both coals. Oil agglomeration is known to be sensitive to surface properties of coal. Since surface properties of coals depend not only on the rank of coal but also on their origin (depositional environment) and mineralogical composition, both the applicability of this new improved agglomeration process to the non-Australian coals and its efficiency became the motivation for this study. To evaluate the applicability of the new process to both Canadian bituminous and Russian sub-bituminous coals, a series of bench-scale tests were carried out under conditions similar to those described by van Netten et al. (2016) for the Australian coals. Based on the results obtained in this research, new boundary conditions for the application of the HIP emulsion-based oil agglomeration process have been outlined and conclusions on the viability of the new process to treat ultra-fine coal from Western Canada and Russian sub-bituminous coal fines have been reached.INTRODUCTION In most cases, to meet the market requirements, the mined coal has to be processed to reduce the ash content by the removal of mineral matter and thus to increase the quality of the coal products (van Netten et al., 2016). Generally, flotation is used for processing fines from high rank coals; however, there are high losses of very fine coal due to the inefficiency of this process. Furthermore, difficulty in dewatering the fine coal results in excessive moisture levels causing coal handleability issues, which increases costs in the coal-cleaning industry (Capes & Darcovich, 1984). Much of the development that has occurred in fine coal cleaning has taken place with higher-value coal, often metallurgical (Klima et al., 2012). If the fine coal is deemed to be too difficult or expensive to process, it may be discarded as waste (van Netten et al, 2014). Such disposal not only creates an environmental liability but may also result in the loss of a valuable, high quality product that is better liberated than the coarser fractions of coal."

Jan 1, 2018