Search Documents

By Richter, E. Charikinya

"Mineral processing unit models require information on particulate properties such as particle size, solids flowrate and mineralogical composition to model their operations. Process models that describe the separation process can be classified based on the level of information required from the ore, i.e. the feed stream to the separating unit. The most comprehensive level of mineral processing models is the particle-based modelling approach. Particle based modelling describes a modelling approach where mineral composition, mineral liberation and textural information of particles making up the process streams is used in modelling. The advantage of this approach is that all model streams carry particle level information (size, liberation, shape). This information is obtained by applying automated mineralogy techniques such as Quantitative Evaluation of Minerals by Scanning Electron Microscopy (QEMSCAN) analysis which provide accurate and detailed information on process stream particle properties. Currently the use of liberation information in modelling and simulation is rare, due to the limited number of separation models that liberation data as input. The objective of this study is to develop a particle based model for a dry magnetic separator, where mineralogical information is used directly to simulate a dry magnetic separator operation. Magnetic separation tests were carried out on high, medium and low grade magnetite ores using a laboratory magnetic separator. Streams from the separator were sampled and sized for chemical and liberation analyses. A sized mass and elemental balance around the magnetic separator was carried out. The elemental assays of each stream were converted to mineral quantities and a sized mineral balance was done. QEMSCAN measured liberation data was reconciled to the mineral balance based on mineral quantities obtained from chemical assays. This was followed by the development of a particle based model that calculates the trajectory of a single particle based on its mineral composition and textural properties. The model was tested on experimental data and was able to predict the effect of variation in process feed stream mineralogical attributes (liberation, grade, particle size) on magnetic separation performance. Results of this study highlight the benefits of the particle based modelling approach. INTRODUCTION The extraction of mineral values from ore requires liberation of the value minerals from the gangue followed by their separation. Liberation is achieved by size reduction operations (Desmond, 2008; Fuerstenau and Abouzeid, 2002). Separation of gangue material from value mineral takes place in various mineral upgrading stages such as classification, magnetic separation and flotation. In these concentration stages value minerals are separated from gangue minerals based on the physical properties of the ore particles making up the feed such as size, liberation, volume of magnetic material and density. The success of separation is related to the liberation of the feed particles, the performance of the separation technology applied, as well as the inherent characteristics of the feed material (Leißner et al., 2013)."

Jan 1, 2018

By Jorge Rubio, Gabriel Berkowitz, Fabiano Capponim, Carlos Perez Guerrero, Elves Matiolo, Denise G. Nunes

This paper describes some advances in flotation research in fines (“F” 38 to 13 µm) and ultrafines (“UF” < 13 µm) mineral recovery by two different techniques, at laboratory scale. Extender flotation and flotation with .multi-bubbles. (bubbles with a wide size distribution) of copper sulphide fines (ore feed of about 1 % Cu) were compared with a .standardised. mill laboratory procedure. Comparative evaluation was made through concentrate grade and recovery (size by size results included), .true. (bubbles-particles attachment only) flotation recoveries and process kinetics. Both techniques yielded higher metallurgical efficiencies than the mill standard but better results were obtained with the extender flotation, with emulsified diesel oil (90 gt-1). Concentrate recoveries were of the order of 85-90 % (84 % in standard conditions), 14-17 % Cu grade (15 % Cu in the standard) and 3.5-4.5 min-1 for the Klimpel rate constant (3 min-1 in the standard). Size by size and true flotation results proved that metallurgical and kinetic gains, obtained with the two techniques, might be attributed to fines and ultrafines enhancement. Data obtained are discussed in terms of physical and physico-chemical parameters related to aggregation and capture (of particles by bubbles) phenomena and the practical potential of these techniques are envisaged.

Jan 1, 2003

In this study, the effect of different regrinding conditions on the depression of fine pyrite at the cleaner stage was investigated. The regrinding condition was manipulated by different grinding media (stainless steel and mild steel). It was found that, after regrinding with mild steel grinding media, the flotation recovery of pyrite is much lower than with stainless steel grinding media, and it is more difficult to restore by adding more collector. This means, regrinding with mild steel grinding media may depress the pyrite flotation more strongly. The copper activation of pyrite during regrinding was also studied. It was found, that the mild steel grinding media is more beneficial to copper activation than stainless steel media. Additionally, the analysis of pyrite recovery based on the particle size indicated, that the fine particles are more susceptible to different grinding environments than intermediate and coarse particles and therefore are more easily depressed with a much lower flotation recovery.

Sep 1, 2012

By K. C. Corin, M. S. Manono, J. G. Wiese

"It has been suggested that hydroxo species, particularly those of calcium, selectively adsorb onto gangue minerals. Such species enhance the depressive action of carboxymethyl cellulose (CMC) onto gangue via an acid-base interaction between the positively charged mineral surface and the negatively charged CMC molecule. Thus, the hydrophilicity of gangue minerals is enhanced, preventing the dilution of the concentrate. However, as there is little evidence to support these claims it is important to investigate. Adsorption data and mineral surface charge analyses will allow a fundamental understanding into how electrolytes and their ionic strengths affect gangue-depressant adsorption. It is strongly anticipated that decoupling these effects will allow process operators to tailor their process water quality needs towards best flotation operating regimes and in the long run effect closed water circuits. Thus, using talc and pyrrhotite as proxies, this work investigates the influence of the ionic strength of process water on the adsorption of CMC onto minerals in sulphide flotation.INTRODUCTIONThe phenomenon of gangue depression in mineral flotation is of critical importance as regards the attainment of a required concentrate grade. This thus suggests that the depressant of choice has to have a highly selective affinity for the targeted gangue minerals. This would ensure the necessary prevention of gangue from reporting to the concentrate without inadvertently depressing the value bearing mineral. The chemistry of the environment regulates the manner in which gangue depression occurs. In sulphide flotation, polysaccharides are used as depressants of choice to depress naturally floatable gangue which may in the case of Merensky ores exist as talc. The two widely used polysaccharides in the South African context are carboxymethyl cellulose (CMC) and modified guar gum. It is suggested that polysaccharides depress gangue by rendering the surface of gangue hydrophilic or by preventing the formation of hydrophobic layers on gangue mineral surface, forming large gangue aggregates and thereby increasing their heterocoagulative nature (Shortridge et al., 1999)."

Jan 1, 2018

By S. Banisi, A. Haji-Zadeh, H. Asadi, M. Maleki-Moghaddam

One area in AG/SAG milling field which has received a great attention is the optimization of liner design for any application to increase the availability of mills. The Gol-E-Gohar iron ore concentration plant uses three 9m × 2.05m autogenous mills (AG) in parallel in a dry operation. The AG mill shell is lined with three series (57 cm each) of 36-row liners. Due to large variations in feed characteristics and inadequate blending, the performance of AG mills has been lower than the target value. Therefore, to improve the comminution efficiency, the optimization of the design of AG mill shell liners was applied in this plant. By simulation it was found that increasing the liner lifter face angle from 7 to 30° while maintaining the original lifter height (i.e., 22.5 cm) could provide an appropriate charge trajectory. Measurement of the wear profiles of shell liners indicated that the wear along the liner length was not uniform and the highest wear occurred between 0.5 m and 1.2 m of the mill length. A new liner design was proposed by redistributing the metal from parts with a lower wear rate to the parts with a higher wear rate to arrive at a uniform wear profile along the liner length at the liner removal time. The non-uniform shell liner was constructed and installed in one of the three parallel dry AG mills. It was found that the first and second liner designs increased the mill throughput by 2.6 and 7.5%, respectively. After conversion to SAG milling on the account of liner change, 18% (from 413 to 489 t/h) increase in throughput was realized. It was predicted that the non-uniform liner designs will increase the liner life time by 10% and will reduce the scrap metal from the current value of 59% to 50%.

Jan 1, 2014

By S. M. Javad Koleini

The aim of this research is to extract zinc from complex lead and zinc ore containing carbo- silicate lead and zinc minerals using sulphuric acid. Samples, taken from Dareh Zanjireh mine located in central of Iran, were subjected to leaching tests after calcination process. Experiments were planed according to the Taguchi statistical method. The calcinated samples contain 13.98% zinc and the constituting minerals being dolomite and zincate. Various parameters such as speed of mixing, temperature, time, solid to liquid ratio and pH were studied. A solid to liquid ratio of 1:6 gr/mL at 60°C and 800 rpm speed of mixing for 30 minutes resulted in a product with 85.96% zinc recoveries.

Jan 1, 2014

By D. Krawczykowski, D. Saramak, T. Gawenda

"Annual world zinc consumption is as high as nearly 14 millions of tonnes. Approximately 50% share of zinc is used for corrosion protection in processes of continuous galvanization and the hot dip processes. In the latter, two zinc containing residues are produced: zinc ash and hard zinc, which constitute around 10% each. Paper concerns the method of possible separation of metallic zinc from the non-metallic zinc compounds from the zinc ashes – the waste product of hot dip galvanization process. The investigative programme covered the comminution tests of the feed (zinc ash) in selected crushers: jaw crusher, roller crusher and impactor. Results of investigations show that application of individual crushing device results in various breakage of the feed sample. Impact force caused the highest increase in finest particles size fractions of the product, while metallic and non-metallic fractions were comminuted differently. The compression force, in turn, caused the selective comminution, i.e. the breakage of metallic zinc was observed in a higher degree. The presented approach appears to be an economical supplementary method of initial recovery of metallic zinc from metallurgical zinc waste. For the high demands for the zinc in the world and the need of corrosion protection, the method presented in the paper helps in more effective zinc recovery and environmental protection.INTRODUCTION AND METHODOLOGY World production of metallic zinc during last decade shows a slight increase and in recent years its consumptions reach 14 millions of tonnes. Figure 1 shows world production of zinc in the time period 2009 – 2016. Main directions of zinc utilization include: - Galvanization - Production of zinc alloys - Brass and bronze production - Semi-manufactures of zinc - Chemicals The major share in global zinc consumption constitute galvanization process (Bright 2007). Two main types of zinc galvanization are: hot-dip galvanizing (HDG) and electro-galvanizing."

Jan 1, 2018

By X. H. Li, F. Xie, Q. Zhang, Z. H. Shen, S. Mao

"There is abundant rare-earth element(REE) in our country, but it is very fragmented in the earth's crust, and it is very difficult to mining or mining cost is extremely high. There are few of industrial value rare-earth deposits. There is a lot of concomitant rare-earth deposits, and the comprehensive utilization value is high. There is very rich carlin-type gold resource, associated with a certain amount of REE in the southwest of Guizhou province. In order toutilize comprehensively the resources, this paper conducts the study on the occurrence characteristics of REE in the ore. By the chemical analysis, the gold grade is 3.35g/t, the organic carbon 0.81%, the total REE 0.022%, which is a high carbon fine disseminated gold ore. By the optical microscope and XRD analysis, the major minerals are quartz, pyrite, calcite, limonite, arsenopyrite, mica, kaolinite, clay minerals, etc. In addition, there is a large amount of carbonaceous materials, such as organic carbon, graphite, which is harmful on leaching of gold. By the scanning electron microscopy analysis, there are thorium, lanthanum and neodymium, ytterbium, persimmon and other REE in the ore. Gravity separation shows that REE could be enriched to lighter material mainly, which indicates that REE disseminate closely with lighter materials.INTRODUCTION Carlin-type gold ore is important gold resource in the world, which are mainly distributed in Nevada and its vicinity, as well as the two Golden Triangle of Yunnan, Guizhou, Guangxi and Sichuan, Shanxi, Gansu province in China(Su W.C. et al.,2009; Xia G.X.,1996).Guizhou carlin-type gold ore is the second largest gold resource in the world(Muntean J L et al.,2011), distributing along the southwestern margin of the Yangtze plate, mainly mineralizing in the neopaleozoic-early mesozoic(Xie Z J et al.,2017). Many large gold deposits have been found in southwest in Guizhou in twentieth century, such as Zimuyou,Getang, Lannigou, Shuiyindong and Laowanchang gold deposit, and so on, and the gold reserves reach over 100 tons(Xia Y. et al.,2009).There is a certain amount of rare-earth resource in the carlin-type gold ore in the southwest in Guizhou province, and the current researches might mainly focus on characteristics of REE from the angle of geological mineralization(AnanyevY.,2015), not from the angle of separation and enrichment."

Jan 1, 2018

By K. C. Corin

It is well known that the grinding circuit plays a crucial role in flotation. The effect of pulp chemistry during grinding is often overlooked. It is believed that the surface properties of the minerals can be adjusted during flotation rather than during grinding. However, recent development in surface analysis techniques (TOF-SIMS, XPS, and AES etc.) have proven that the hydrophilic iron hydroxides formed at the mineral surface during grinding make it difficult for collector adsorption, which may result in poor grades and recoveries of the valuable minerals. This study investigated the effect of the pulp chemistry conditions during milling and the subsequent effects on flotation performance of an Nkomati ore. The results have shown that there was approximately 10 % increase in Ni recovery, when the ore was ground at a dissolved oxygen (DO) concentration of 0 ppm (DO-0) in comparison to no gas control during the grinding stage. However, when the pH was changed from 9 to 11, no gas control resulted in a 20 % decrease in the Ni recovery compared to only 5 % decrease in the Ni recovery at DO-0. A noteworthy observation is that controlling a combination of DO and pH during grinding is of critical importance for better floatability and selectivity for such a system. It also became clear from this study that the presence of oxygen is critical to the consumption of xanthate, which is consistent with the general literature. It has been established that grinding at lower DO levels/redox potentials (Eh) in the presence of xanthate significantly improves the flotation performance of the valuable minerals.

Sep 1, 2012

By A. Gueciouer, A. Akkouche, K. Chalah, A. Benmounah

"Drilling solid waste is a typical industrial solid waste, and it is a major pollutant source to ecological environment. Generally, waste management dewatering systems separate solids and fine particles from the liquid phase of drilling fluid, thereby leaving a clarified aqueous solution and allow the cleaning of waste fluids. Typically, dewatering waste management systems clean drilling fluid through coagulation, flocculation and/or mechanical separation. Chemicals used in dewatering are based on the coagulation-flocculation process, which it facilitate the removal of suspended solids and colloidal particles. The factors which can promote the coagulation-flocculation are velocity gradient, contact time, and PH. The objective of this work is to optimize a formulation adequate for dewatering based on the coagulation-flocculation process used coagulant (Aluminum sulphate), anionic flocculants (Partially Hydrolyzed Polyacrylamide) and anionic polyelectrolytes (in solid form with linear chain with very high molecular weight). The results obtained show the good efficiency of the coagulant and flocculants. INTRODUCTION Rig site dewatering of drilling fluids with recycling of processed water can help an operator to comply with environmental rules by reducing volumes of waste and reducing long term liabilities. It can also reduce disposal costs and provide a cleaner drill site overall. Most of the environmental concerns during the 1980s involved hazardous materials and toxic wastes. Drilling fluids, many of which are chemically benign, have escaped many of the difficult-to-comply-with rules and regulations. During the 1990s, however, operators may be required to submit a written plan for liquid waste reduction for even nonhazardous materials. Many states and local agencies may institute total bans on oil field wastes. Drilling rigs typically produce about 1 bbl of liquid waste for every 1 ft of hole drilled. Thus, a typical drilling operation can produce a large quantity of waste [1]. To improve the dewaterability of sludge, different pretreatment processes have been widely studied and developed including thermal, chemical, magnetic, mechanical, acoustic, electric, electro-acoustic and their hybrid treatment processes [2]. Rig site dewatering (figure 1) is the process of injecting coagulants or flocculating chemicals into the mud entering a large clarifying centrifuge. Coagulation occurs when the solid and allowing it to be attracted to other solids by van der waals forces. Flocculation is the binding of individual solid particles into aggregates of multiple particles. It is physical, rather than electrical, and occurs when one segment of a flocculating polymer chain absorbs simultaneously onto more than one particle [3]."

Jan 1, 2018

By R. D. van der Weijden, W. F. C. van Wageningen

"Copper(II) can be recovered or removed from acidic copper sulfate solutions as cuprite or metallic copper powder by reduction with carbohydrates (van der Weijden et al., 2001, 2002). In order to make this process suitable for a commercial scale pipe reactor, process conditions and reactor configuration need to guarantee proper throughput of the dilute suspension. This is where crystal engineering also comes into view. Copper powder characteristics, such as size and shape of particles, influence the tendency to adhere to reactor walls and to agglomerate, which in turn influence the throughput. Furthermore, separation, drying, packaging and product quality, are dependent on the powder characteristics.In this paper the effect of both chemical and physical parameters on the shape and size of particles were systematically studied in a number of autoclave experiments. These parameters include mixing, Cu(II) concentration, pH, temperature, seeding, use of additives and reactor materials. Additionally, Monte Carlo simulations of copper growth inside a Kenics static mixer were made. Results show that the use of additives, and the use of static mixers influence particle characteristics the most."

Jan 1, 2003

By P. Huang, D. W. Fuerstenau

Various factors that control the natural flotability of talc, including differences due to crystal face and edge effects, were delineated. For study of talc depression phenomena, dextrin was used as a model depressant. For the enhancement of talc flotation, dodecylammonium acetate (DDAA) was used as the collector. The interaction of DDAA with talc was assessed by flotation experiments and electrokinetic (zeta potential) measurements, from which the role of hydrophobic bonding can be demonstrated. The results presented in this paper provide useful information on how the crystal chemistry and surface chemistry control the electrical double layer, adsorption phenomena, wettability, and flotation behavior of talc in aqueous media.

Jan 1, 2003

By V. V. Ramarao

Grinding and flotation operations deliver better-optimized performance when they are monitored and controlled in terms of the minerals they process rather than as elemental assays that we usually refer to. Mesh of grind (MoG), liberation, floatability, grade and recovery etc. are more directly related with the minerals and their characteristics rather than the elemental assays. Hence, online analyzers only provide the status for the grade and recovery of metals and not the direction for the enhanced performance. Central Research and Development Laboratory (CRDL) and Rampura Agucha Mine (RAM) mill section of Hindustan Zinc Limited (HZL) jointly undertook various survey campaigns in the grinding and flotation process streams. Grinding circuit surveys involved systematic collection of representative samples from different grinding circuit streams under stabilized conditions for monitoring particle size and process mineralogy details across individual grinding circuit. Flotation survey campaigns included study of fort-nightly / monthly composites of un-ground flotation feed, lead concentrate, lead tailing, zinc concentrate and final tailing samples for size distribution details in the 150 ? 38 micron range, chemical analysis and mineral characterization through optical microscope. This work details the investigations results and their implications on beneficiation performance. Grinding circuit survey campaigns supported the task for modifying the originally installed configuration of hydrocyclones, to limit recovery losses due to excess grinding of soft galena and related silver minerals. Flotation plant surveys helped in adjusting flotation circuit process parameters to reduce loss of liberated and floatable galena and sphalerite grains into their respective tailing streams. Keywords: grinding circuits, survey campaign, hydrocyclones, mineral liberation and locking, lead-zinc ore beneficiation operation

Sep 1, 2012

By V. Vogt

During the phosphating of car bodies containing aluminium, the employed phosphating chemicals zinc, manganese and nickel are, for thermodynamic reasons, only used to a limited extent for the desired surface coating. The major proportion of these metals is discharged together with the incidental cryolite-containing phosphating sludges and the rinse water. Commissioned by the German Federal Ministry of Education and Research (BMBF), the Institute of Mineral and Waste Processing, Waste Disposal and Geomechanics at the Clausthal University of Technology has developed a two-stage process for the production-integrated recovery of the dragged out chemicals and for closing the rinse water cycle for Audi AG. During the first stage, the phosphating chemicals are recovered by means of leaching. In the second stage, the rinse water is treated by means of electroflotation followed by an ion exchanger.

Jan 1, 2014

By L. M. Sun

Baotou Baiyunerbo Mines Location in Inner Mongolia is a famous deposit of iron mineral and rare earth mineral accreting. The iron ore has very complicated ingredients and minerals composing. In the mine, there is not only magnetite ore but also hematite ore, so that it is impossible for high grade iron concentrate to adopt single wet low-intensity magnetic separation or high-intensity magnetic separation to concentrate iron mineral. Because of mixing the magnetite with hematite mineral in feed ore, recovery of iron of magnetite production system in the mineral processing plant is less than other mineral processing plants. Therefore, the research for increasing recovery of iron of the magnetite production system in the plant was undertaken. The paper presented the research for using dry magnetic separation to increase recovery of iron concentrate of the magnetite production system in the plant. It mainly includes dry magnetic separation test and wet magnetic separation and reverse flotation test. The test results indicated that dry magnetic separation is a important way to improve the feature of feed ore of the magnetite production system and to increase the recovery of iron. The recovery of iron may increase from about 70% to over 80%. The research also presented optimum operation parameters of the dry magnetic separator and the separation flowsheet. In conclusion, using dry magnetic separation to treat with feed ore of the magnetite production system in the plant to increase the recovery of iron is a feasible technique. The research present a new way for the mineral processing plant to made technology innovate to increase the recovery of iron concentrate of the plant in future.

Jan 1, 2014

By G. Venkateswara Rao

The jigging of ferrous ore to produce higher-grade products has been practiced for many decades. This is due to easy separation, a beneficial trade- off between operating cost and reduced yield relative to Dense Media Separation (DMS). Jigging becomes prominent for beneficiation of iron ores in the coarser size range. At present drive is towards the use of under bed air pulsed jigs for the beneficiation of ferrous ores. The main advantage is that the under bed air pulsed jigs are capable of generating the large pulse of amplitudes required to fluidize a deep bed of heavy ores particularly lump iron ore up to 40mm size. The major jig parameters effecting the jigging operation are bed height, shape of the pulse, residence time, operating pressure, valve cycle time and water flow rate. With the pulse shape set correctly for optimum stratification rate, even it is still necessary to provide enough residence time, to ensure the difficult material will take time to migrate to the expected layer in the bed. In order to find the Jig Stratification Index (JIS) parameters like bed height, operating pressure, water flow rate, cycle valve time and shape of the pulse were optimized first by conducting various tests. Typical Iron ore samples from Odisha (both lump and fines) were subjected to stratification studies at residence time of 1, 5 and 15 minutes. Jig Stratification Index (JSI) for both lump (0.30) and fines (0.20) were determined by using APIC Jig. The maximum possible JSI was calculated by using heavy liquid separation test (0.42 for lump and 0.24 for fines). It is found that the jig bed JSI is less than the Heavy liquid JSI for both lump and fines. The ratio of Jig bed JSI to the heavy liquid JSI is 0.83 for lump and 0.71 for fines. The JSI and ratio of Jig bed JSI to Heavy liquid JSI are low for fines due to fluid turbulences causing some degree of remixing in the jig bed. The fluid turbulences are more for fines than lump, hence jigging of fines is difficult and challenging. Keywords: sub grade iron ore, gravity separation, jigging, apic jig, stratification, residence time, jig stratification index

Sep 1, 2012

By A. Boulton

Low molecular weight synthetic polymers substituted with hydroxyl, carboxyl or sulfonate functional groups were used to improve the flotation separation of zinc or copper sulfide minerals from iron sulfide gangue minerals in three massive sulfide ores of different mineral composition. These polymers produced significant improvements in zinc or copper grades as a result of a selective depression of iron sulfide minerals. It was shown that this selectivity was the result of preferential adsorption of the polymer on the surface of the iron sulfide minerals. The different types of interaction between the functional group on the polymers and the sulfide mineral surfaces could explain the trends observed in the flotation results.

Jan 1, 2003

By X. Q. Chen

According to the different characters of the middle-low grade bauxite, based on the normal flotation & reverse flotation technology, the author innovates the new technology which is named bi-flotation, it integrates the advantages of normal flotation & reverse flotation, while avoids their disadvantages. Take Henan middle-low grade bauxite as research object, according to the pilot experiment of bi-flotation technology, the concentrate A/S is 9.37 and the recovery of alumina is 80.18% by flotation separate the raw ore which A/S is only 4.19.

Jan 1, 2014

By Kauko T. Ingerttilä, Jouko O. Kallioinen, Jaakko O. Leppinen, Alexander V. Lashkul, Vladimir E. Nenno

The Separation in Froth (SIF) technique is based on the idea that the pulp is fed directly onto the froth layer prepared on the surface of liquid medium providing an effective method for separation of coarse particles up to a few millimeters size. Thus the SIF process can result in substantial savings in grinding energy and flotation chemicals. In this work flotation of apatite, calcite and silicate minerals from various industrial sources was investigated using laboratory and pilot plant-scale SIF machines. Flotation of diamonds was also investigated on laboratory scale. It was observed that all the minerals mentioned above can be successfully floated up to about 3 mm particle size. Beneficiation tests with the coarse fractions of classification circuits indicated that final grade calcite concentrate can be obtained with over 90% recovery in one SIF step in this grain size (typically 0,1 to 1,5 mm). Similarly, substantial upgrading of coarse apatite was achieved without grinding it to the fineness required by conventional flotation. SIF could also be applied to the recovery of coarse apatite from the tailings of a conventional flotation process. The capacity measured in the pilot plant test runs for a 1 m2 cell was typically 30 t/m2h. Presently, a full-scale process using the SIF technology is being installed for coarse apatite recovery.

Jan 1, 2003

By Wei Zhang, Jinhong Zhang

"In froth flotation, the adsorption of collector on mineral surface is critical for a successful flotation process. In present work, an atomic force microscopy (AFM) has been applied to study the adsorption of potassium amyl xanthate (PAX) on copper sulfides, i.e., chalcopyrite, chalcocite and bornite. The in-situ collected AFM images show that PAX adsorbs on chalcopyrite mainly in the form of oily dixanthogen; while it strongly adsorbs on chalcocite and bornite in the form of insoluble metal xanthate, which binds strongly with the mineral surface. The information obtained from the AFM study shed lights on the collectivity and therefore the selection of specific collector for different copper sulfide minerals in industrial practice.INTRODUCTIONFroth flotation, which treats the highest throughput in mining industry and produces the maximum economic outcome of any surface chemistry process, has been widely applied for the concentration of copper sulfide minerals, i.e., chalcopyrite, chalcocite and bornite. In flotation, collectors are added into the pulp (mixture of water and fine-grained minerals) to selectively adsorb onto the target mineral and render its surface with high hydrophobicity, which is generally beneficial for a strong mineral-bubble attachment and thus a high flotation recovery. Therefore, the adsorption of collector on mineral surface is vital for a successful flotation process and it has been studied by applying various surface analysis techniques, such as IR (Infrared Spectroscopy), CV (Cyclic Voltammetry) and XPS (X-ray Photoelectron Spectroscopy). (Poling, 1963; Allison et al., 1972; Mielczarski et al., 1984; Leppinen et al., 1989; Kartio et al., 1996) These studies have revealed a lot of information, such as the reaction, product and mechanism, of the adsorption of chemicals on mineral surface. It is also of great interest to directly get the image of adsorbed collectors on mineral surface changing with pulp chemistry, such as pH, redox potential, ionic strength and chemical’s dosage."

Jan 1, 2018