Search Documents

By Richard H. Granhom

Detonation pressure, or Chapman-Jouguet pressure, is an intrinsic property of an explosive, and like detonation velocity, is an indicator of explosive performance. Pressure and velocity are also important for calibrating computer codes and for other calculations such as the stress imparted to rock or metal by an explosive. The detonation pressures, P~cj, of many "ideal" explosives have been measured indirectly by recording some hydrodynamic flow variable other than pressure, with P~cj being inferred from hydrodynamics and the assumed Chapman-Jouguet equations. One such method is the difficult and expensive "aquarium technique''.] Commercial explosive manufacturers generally rely on estimates of P~cj generated by computer codes not explicitly designed for non-ideal explosives typically used in commercial applications. Over the last decade, U.S. national and government laboratories have developed in-situ gauge techniques such as the manganin gauge, for direct measurement of detonation pressure. Manganin is an alloy of copper, manganese and nickel, and is ideally suited for use as a pressure transducer because its electrical resistance changes with pressure, but is nearly constant with changes in temperature. A simplified manganin gauge technique adapted for use at a commercial test site is described and some initial results from measurements on commercial emulsion explosives are presented.

Jan 1, 1991

By Virgil J. Stachura, Calvin L. Cumerlato

The U. S. Bureau of Mines is conducting research on blasting methods that reduce highwall overbreak and the associated rockfall hazards. This paper presents the results of tests using a low-density water gel to improve the quality of air-decked presplit blasts at a surface coal mine in New Mexico. The explosive's specific gravity averaged 0.50 and was bulk loaded using a modified truck which injected the gassing agent. Reductions in overbreak and resulting rockfall were achieved in comparison to a highwall presplit with ANFO. The test sections used 15° angled blast holes and resulted in 1,119 m (3,672 ft) of air deck presplit highwall using a low-density water gel which was then compared to 894 m (2,934 ft) of highwall shot with an ANFO air decked presplit design. The total quantity of explosives per hole ranged from 68 to 113 kg (150 to 250 lbs) and the 27 cm (10-5/8in) holes were 19- to 33-m (62- to 108-ft) deep on 5.5 m (18-ft) centers. Periodic visual examination and photographic surveys of the highwall test areas were used to document the amount of rockfall. In addition, laser profiles of selected sections were conducted to further delineate the damage and highwall contour differences.

Jan 1, 1995

By Andrew F. McKown

Overbreak and damage to rock walls at the perimeter of rock excavation can lead to safety problems due to rock falls and additional costs due to a] extra mucking, b] extra concrete or shotcrete to backfill overbreak, c] additional rock reinforcement, d] additional water inflow and e] additional maintenance of rock walls. To minimize these undesirable effects, there are several perimeter control techniques available (i.e. line drilling, cushion blasting, pre-splitting, smooth blasting, and fracture control blasting) which control perimeter hole spacing, burden and loading to provide a smooth, stable excavation contour. Conventional perimeter control loading and hole spacing is satisfactory for massive, homogeneous formations, but when blasting in weathered or fractured rock closer spacing and very light loading is required.

Jan 1, 1984

By Thomas Rupp, Michael Siegwart

The paper presents the vibration and sound emission measurement campaigns carried out in 2007 in preparation for the Ceneri-Basistunnel construction. We also present the vibration measurement campaign conducted during the construction of the Zimmerberg-Basistunnel. Both tunnels form an integral part of the Swiss Federal Railway Company Neue Eisenbahn Alpentransversale project (NEAT). This strategic project comprised the construction of several new tunnels. Its aim is the improvement of the existing infrastructure. The improved infrastructure will be able to accommodate a larger volume of railway traffic that is also crossing the Alps at higher speeds. The construction of the Ceneri-Basistunnel commenced in 2006. Both the Zimmerberg-Basistunnel and the Ceneri- Basistunnel are located underneath densely populated areas. Therefore, noise and vibration emissions have to be kept to a minimum and must not exceed applicable codes of practice. In order to identify the most appropriate blasting strategy for the yet to be constructed Ceneri-Basistunnel, blasting trials were conducted. The paper presents the findings of these trials and identifies ways to reduce both noise and vibration emissions from blasting. The construction of the first phase of the Zimmerberg-Basistunnel took place between 1999 and 2003. While the first phase is already in operation, the construction of the second phase has been postponed (commencement originally due in 2007). The Zimmerberg-Basistunnel connects the outskirts of Zürich with the city centre. As the tunnel site was not located close to the surface near populated grounds, no special measures were needed to reduce the noise emissions from blasting. However during the construction of the tunnel, the vibration emissions from blasting were monitored on more than 50 locations on the surface. The paper presents the analysis of some of the data. An emphasis is placed on the appropriate synopsis and presentation of data for documentation purposes.

Jan 1, 2009

By Thierry Bernard

It was in the 1980s that USBM published one of the first regulations to protect constructions from the effects of vibrations caused by mine blasts. Several countries have made their own regulations or recommendations since then with vibration limits that are often lower. However, on many sites, operators choose vibration limits that are lower than those of the existing standards, in order to limit the number of complaints received. The real question is how can we know what level of vibration is susceptible to create or worsen an existing crack in a construction. MCM, to the north of Quebec, is working a deposit on the periphery of the town of Malartic. Within the scope of its environmental monitoring programme, together with the joint monitoring committee, MCM has equipped four sample houses for over 18 months, in order to learn if there is a relationship between the evolution of damage to existing constructions and the seismic levels of vibrations created by mine blasts. The publication presents the results of this unique study that has analyzed millions of measurements (seismic, extensometric, and temperature) to define what relationship exists between the levels of vibration and the movement of cracks. Some surprising results versus some published previously (see ref) might change our perception of the subject.

Jan 1, 2018

By Syed M. Tariq, John W. Wilson, Paul N. Worsey

The position of a major joint in relation to a blasthole has a significant effect in presplitting. Broad research into the combined effects of firing two decoupled blastholes has been performed in the past. The effects of joints simulated between two blastholes has also been evaluated. However, no attempt has been made to investigate the splitting effects produced by firing a single decoupled blasthole. This paper presents the results of such an investigation.

Jan 1, 1996

By Tristan Worsey, Nathan Rouse, Daykin Schnell

The authors were retained by a proposed underground metals mine operation to evaluate the potential blast vibration amplitudes that could be generated at surface structures above the proposed mine. Literature reviews of published blasting documentation gave little information, data, or models on surface blast vibrations produced by underground mines. At the client’s request, the authors contacted a number of underground mining operations to evaluate interest in sharing blast vibration data with the authors so that the authors could develop an underground-to-surface blast vibration regression equation. The authors worked with three underground metals mining operations to collect surface blast vibration data produced by heading blasts and stope blasts. The data included blast vibration amplitude values, seismograph records, blast design geometry, charge weights, and detonator delay and sequence designs. The total amount of information was used to produce a regression equation and summary dataset that could be used by the proposed underground mining operation to evaluate blast vibration amplitudes that will be generated on the surface. This work is published and presented so that operations with proposed underground mines or proposed underground mine extensions can use these equations to predict vibration amplitudes on the surface above the mine workings before any blasting occurs.

By Ashlin Pillay, Osamu Iwata

Hong Kong is ranked as the world’s third most important international financial hub and attracts significant growth and development annually. The city is also known as the world's most vertical city, the most common view from your window in Hong Kong city centre is probably the window of another 30 storey skyscraper. The increasing demand for real estate in this bustling Metropolis has placed immense pressures on its transportation infrastructure because whilst the construction continuously grows upward with larger and larger skyscrapers, it leaves the transportation planners with very little choice but to go underground. As a first world city, interrupting daily business operations is simply not an option; however, of even greater concern is the safety of these 8 million residents. Blasting Regulations are under the strict control of the Mines Division showing zero tolerance to the breaching of safety standards. The Ho Man Tin Station (HOM) excavation, a part of the Kwun Tong Line Extension (KTE) project situated in Hong Kong began in June 2012 and is one such project that is under strict regulations from the Mines Division. The HOM project is a cross cut interchange station between the Kwun Tong Line Extension (KTE) and Shatin Central Link (SCL).

Jan 1, 2015

By Kirk Yeager

All explosive formulations display some sensitivity to heat. A common technique utilized to measure an explosive’s response to thermal stimulation is differential scanning calorimetry (DSC). As DSC analysis is run on quantities of material easily handled in a laboratory setting, and is relatively inexpensive, it tends to be one of the more predominant tools utilized to determine potential thermal hazards of energetic materials. The analysis of energetic materials via DSC provides unique challenges, as both large energy outputs and significant production of gaseous products result from their decompositions. In addition, the unique thermal decomposition characteristics of ammonium nitrate (AN) based materials have also created difficulties in DSC analyses. A wide variety of techniques have been developed to study the decomposition of explosives. Traditionally, sealed glass capillaries were utilized to house samples. Recently, the introduction of specialty cells designed to withstand high pressures has enabled new sampling techniques to be developed. Analyses of explosives with both traditional and “high-pressure” cells will be compared and contrasted. Lessons learned about the application of both techniques towards analyzing thermal hazards such as incompatibilities will be presented. Inconsistencies in the results displayed during analyses of AN-based explosives will be highlighted. Recommendations on the best approach for analyzing the more problematic AN formulations will be given.

Jan 1, 2000

By Roger Holmberg, William Hustrulid

Swedish cautious blasting techniques were used to excavate a room at the CSM Experimental Mine in Idaho Springs, Colorado,as part of a ONWI/DOE sponsored nuclear waste disposal research program.

Jan 1, 1981

By Lee Wehner, Daryl Kin, John Bolger

The Maumee Quarry, located in the city of Maumee, Ohio, has large in-situ cavities, ranging in size from 3 ft (.91 m) in diameter to over 15 ft (4.5 m). The drill/blast team challenge is to drill, load and shoot the geologically disturbed rock in a safe, cost efficient manner, while in close proximity to a commercial area. A continuous improvement process, managed by a Blast Optimization Team (BOT), was implemented to quantify the innovative explosive loading techniques that have been implemented. Borehole camera monitoring, modified loading practices, the need for accurate drill hole logging and open communications between the drill and blast crew proves critical to the success of the operation. Safe Standard Operating Procedures (SSOPs) have been developed and are strictly enforced for the drill/blast cycle. All blasts are monitored with seismographs and recorded on video to provide detailed information as part of the Blast Management Plan. Despite the geological challenges, the measurement of rock fragmentation index versus loader dig rates has provided near optimal crusher throughput.

Jan 1, 2007

By Sandor Nagy

The Explosive and Blasting Department of the Hungarian Mining Research Institute is responsible for the research and development of industrial applications of explosives. Appropriate explosives technology is developed for each application, including the explosive demolition of structures, which belongs within our charge.

Jan 1, 1977

By Karl Ingmarsson

A model for drilling productivity and total drilling cost is presented. It specifically addresses down-thehole drilling, but also covers other drilling methods. The important factors are: 1, productivity in tons drilled; and 2, total cost per drill ton. For non-blasthole applications these factors are measured in drill feet and cost per foot. The model focuses on the entire system and allows the operator to optimize the system based on individual drilling conditions.

Jan 1, 1998

By C. Lownds, U. Steiner

In 2008 a paper from the same source describing four actual cases of exposure of electronic detonators to lightning strikes was presented. It was shown that electronic detonators, like other initiation systems, are vulnerable to very close or direct lightning strikes. At the time of submitting this abstract no further incidents with lightning have been experienced. As a result of those original incidents, and in order to understand how the safety devices inside electronic detonators break down, two series of tests have been done, each with 2 detonator designs. In the first series detonators were subjected to capacitor discharges up to 6kV and 1kJ in energy. In the second series the intensity was increased to 800kV and 24kJ in energy. In the second series, more electrical energy was delivered to the detonator assembly than the explosive energy of the detonator. In both series both detonators showed a spectacular ability to resist very high discharge energies. The tests are described in detail with supporting photographs. The data for both pin-to-pin and pin-to-case (more relevant to lightning) are presented and discussed. The mechanism of breakdown of safety devices is now understood better and the learning is being used to design more robust products. This high-voltage testing is relevant in understanding how electronic detonators might initiate as a result of a very close or direct lightning strike 1. Orica

Jan 1, 2009

By W C. Burkle

A rather common observation over the last several decades at least has been that rock or ore properties influence blasting results more than does the explosive type that has been used in the blast. It we accept that premise than it is held here that the material to be blasted should receive even closer attention as to its properties. Several years ago, Dr. Richard Ash published papers that pointed out the rock properties that mostly influence blasting. These principles are given attention in this paper. We have gone somewhat further - or lets say expanded this subject in regard to the role of rock structure in open pit blasting. Though open pit work is given some prominence, we believe that much can be observed and applied to underground mining.

Jan 1, 1979

By Dale S. Preece, Stephen H. Chung

"In bench blasting, the distribution of loaded explosives with respect to the burden rock has strong effects on digging especially at the toe area. Blast design often focuses on other results such as percent-cast or fragmentation, sometimes leaving a diggability problem at the toe of the blast that is not discovered until excavation. A method for assessing the influence of blast design on diggability has been developed. This method relates the kinetic energy and rock displacement experienced by the material in the muckpile to its diggability. Simulation of the blast along with the calculation of kinetic energy and diggability is done with the discrete element computer program DMC_BLAST(DMC: Distinct Motion Code)."

Jan 1, 1999

Vibration resulting from blasting has been a source of concern from the inception of the use of explosives. As a result many investigations have been made concerning the seismic effects of blasting and at present there is available an adequate set of standards with which to judge seismically the damage capability of a blasting operation.

Jan 1, 1976

By Charles B. Ingram, Neil E. Gehrig

The development of water gel explosive products has been the single most important development in explosive research and development since the invention of nitroglycerine and dyne-mite many years ago. m e Explosives Department of Gulf Oil Chemicals Company has been engaged in the research, development, manufacturing an marketing of slurry explosives and blasting materials for over twenty years. Explosive research and development is being carried out at the Jayhawk Technical Laboratory and the Underwater Testing Facility near Pittsburg, Kansas. There are fourteen manufacturing facilities geographically located around the country to serve the mining, quarrying, and construction industries with a complete line of explosives, blasting agents, and accessories. This paper discusses the Gulf slurry products, their properties, and uses.

Jan 1, 1977

By Don Rapp, Rufus Flinchum

Air blast and flyrock are two of the most critical concerns facing the blaster of today. This paper will provide the blaster with proven procedures for recognizing open face and bench surface problems, explain various surveying methods, and provide the mathematical formulas for calculating and designing proper hole placement and explosive load configuration. A concept called "Pattern Footage" is utilized in conjunction with a USBM study to develop blast designs aimed at minimizing air blast and flyrock. In addition to this main focus, this concept can be used in shot displacement and cast blasting design.

Jan 1, 1993

By Joshua Hoffman, Rhys Baker, Tim O’Brien

Numerous agencies in the Executive Branch of the United States Federal Government have regulatory jurisdiction over the explosives industry. These agencies develop the rules by which the explosives industry must operate, and many have the authority to enforce those rules. Likewise, there are entities in the Legislature that have oversight of those agencies and develop the laws that agencies must operate under. These entities in the Legislative Branch are Congressional Committees. Each committee has their respective jurisdictional authority over various agencies and issues. There are several Congressional Committees with jurisdiction over the agencies that govern the explosives industry and they differ slightly between the House of Representatives and the Senate. This paper discusses this division of power as it relates to the explosives industry. Each branch is responsive to the public and the processes through which each promulgates regulation and legislation require public input in different forms. Options for civic involvement for engaging each of these bodies of power in their respective processes are presented. The differences between legislation and regulation are highlighted along with the processes by which each are promulgated. A proper understanding of the governmental mechanics that affect the explosives industry are critical for the industry to be able to be proactive in playing a role in these processes in a democratic way.