Search Documents

By Thomas L. Barkley

This paper describes an unusual design for a 12 foot diameter, 30 foot deep circular shaft shot in a close in urban environment less than 100 feet from occupied structures. It uses diagrams, video footage, and vibration results to describe a 3 deck, 17 hole burn round used to pull 17 feet in one lift.

Jan 1, 1994

By Fumihiko Sumiya, Koichi Kurokawa, Yukio Kato, Tetsuya Sawada

In some metal mines, it is a serious problem the decomposition of explosives which occurs suddenly by contact with ore containing pyrites under high temperature conditions. In the present paper, we investigated heat resistant properties of emulsion explosives and other industrial explosives by contact with ore containing pyrites under high temperature conditions.

Jan 1, 1992

By Ronald R. Rollins

A continuous propagation velocity measurement probe has been utilized to determine velocities of slurry explosives, whole prills, crushed prills, aluminized crushed prills, in bulk and plastic screw tubes.

Jan 1, 1984

By Mauro Fornaro, Marilena Cardu, Renato Mancini, Daniele Castano

Tunneling by explosive blasting in civil works isn't merely intended to break somehow a way through the rock, rather to drive a permanent, constant cross section, lined way. The current mechanical excavation v/explosive blasting debate is mainly centered on the concept of the tunnel wall quality; and consequently explosive blasting strategy is founded on contour blasting.

Jan 1, 1992

By David A. Smith, B L. Jr Lindsey

Arkansas bauxite varies enormously in its consistency and composition which makes blasting a very difficult operation. Blasting rounds have to be designed based on each particular mine's ore characteristics. The variances are so great in some mines that blasting procedures have to be changed almost daily.

Jan 1, 1979

By Mauro F. Dobran

The use of Slot Raises has been common for many years. The following presentation will compare various methods of developing these Slot Raises and introduce two new ones.

Jan 1, 1996

By I. Petropouleas, J. Croll, R. Bassett

A programme of tests on controlled internal explosions to a class of circular reinforced concrete columns, has allowed the relationships between the blast energy and the extent of local damage to be understood. These tests have also demonstrated the important additional effects on the damage levels of preexisting axial loads.

Jan 1, 2006

By Jim Breedlove, Stephen P. Case

When a major ground subsidence occurred in the AKZO Salt mine at Retsof New York, the company was forced to pick up their production from a lower mine level. Before full production on the lower level was possible, an escapeway and ventilation shaft would have to be constructed. Construction of a shaft under emergency conditions required some special techniques. Dynatec Mine Construction, Inc. of Lakewood Colorado was awarded a contract for the project.

Jan 1, 1995

By Norman S. Smith, Richard L. Ash

Many factors affect rock fragmentation from blasting. One variable seldom considered when designing blasts, however, is the borehole length. An example is described of how the length was adjusted to give better breakage when using 4-inch diameter blastholes at a quarry. To explain the basic principles involved test results from experiments conducted by the authors where borehole lengths were altered are presented and evaluated.

Jan 1, 1976

By Deane Boddorff

A 440 Volt AC power line is a typical power source for energizing electric blasting cap circuits in driving hard rock tunnels. A common misconception exists that the caps actually see 440 Volts. This paper describes an analysis of the entire blasting circuit determining the current flowing and the voltage drops through each component. If, from such an analysis, one determines that the current to the caps is too low or too high, the components that require changing are easily recognized.

Jan 1, 1975

By G Dean Barrett, Ed Jr Smith, Calvin J. Konya

The purpose of the project was two fold: 1. To determine whether Pyrodex, a propellant, manufactured by the Hodgdon Powder Company, could be used as a substitute for high explosives for presplitting in granite and other materials. 2. To determine if Pyrodex, a slow reacting propellant which produces no stress waves in rock because it reacts subsonically, could cause the rock to crack similar to the results achieved with high explosives.

Jan 1, 1986

By Hans Florin

This paper describes the modification of a nonelectric detonator which is ignited by a signal tubing. The heart of the new detonator lies in a so-called ignition transmitting element. The construction of the transmitting element is such that the detonator remains closed even after the signal tube has functioned. Due to the sealing of the delay element, this nonelectric detonator achieves the same accurate delay timing as high tech delay electric detonators and will not fail due to a sudden pressure loss.

Jan 1, 1988

By Scott Giltner, Allan Koski

Blasting is one of the lowest cost yet most critical parts of the mining cycle. This paper discusses the findings of an audit conducted on the blasting operation at an iron ore mine. The purpose of the audit was to review current blasting practices in order to identify opportunities for production/cost improvements. The approach taken in the audit was to observe general blasting practices, their related downstream effects and to compare current procedures to established best practices.

Jan 1, 2009

By Robert J. Nothnagle, Kristen Franz Begor, Rodney W. Sutch

Recovery of contaminated groundwater in a fractured bedrock system presents some unique problems. Typically, the most common problem occurs from the inability to adequately characterize the discrete fractures through which contaminants may be migrating. Without adequate characterization, difficulties arise in properly positioning recovery wells and verifying the performance of the system. To overcome these difficulties at a site in Upstate New York, an innovative approach was developed involving the creation of an artificial fracture zone through controlled blasting to intercept contaminated groundwater flow.

Jan 1, 1988

By Edward J. Walter

An ancillary effect to every blasting operation is the generation of vibration Extensive research has been performed for the purpose of understanding, controlling, and predicting this vibration An examination of these studies clearly shows a variability in the resulting vibration effects It seems logical to expect that identical blasting procedures should produce identical vibration levels, but this is rarely the case. There is a distinct pattern of variation.

Jan 1, 1980

By Calvin Konya, Janos Foldesi

A bridge over a main line railroad system was scheduled for demolition. The bridge was made of reinforced concrete and spanned three mainline railroad tracks which could not be shut down due to blasting or demolition. To further complicate matters, the mainline tracks had high tension power lines running above the tracks, but below the bridge. These high tension wires provided the electricity for electrically powered trains. The tracks could not be damaged or disrupted, nor could the power line be broken.

Jan 1, 1992

By P. Katsabanis

Numerical modelling was used to examine damage in wall control operations. Decoupled charges appear to create larger damage zones than fully coupled low density charges with similar charge distributions: Air was shown to be a very efficient coupling medium, while water coupling resulted in significant damage. However, Mach stems are formed when air is used as a decoupling medium, leading to compression of the charge ahead of the detonation wave. Air decked charges generate two damage zones, one close to the charge and another close to the air-deck/stemming interface, where pressure pulses are reflected. The extent of the latter depends on the length of the air-deck.

Jan 1, 2001

By Andre Pinsonnault, Francois Lefebvre, Yves Newman

In 1989, Les Entreprises Kiewit Ltee signed a C$32 million contract with the Societe d'energie de la Baie James, on behalf of HydroQuebec, to excavate the intake and tailrace channels for a second powerhouse at the LO-2A James Bay hydroelectric project. The multistage contract included removing three marine rock plugs. The first plug was blasted in April 1990. It was a 43 yards wide, triangular shaped wedge that projected into 18 yards of water. Located at the mouth of the intake channel, it contained over 72,000 yd3 of rock, more than twice the 30,000 yd3 found in most rock plugs.

Jan 1, 1991

By R Holmberg, C Sjoberg, B Larsson

This paper describes the excavation of an underground naphta storage facility at Stenungsund in Sweden. The main purpose with this paper is to give an overall view of how the excavation was carried out and in what type of bedrock the storage was built. Emphasis has been done to highlight the importance of using cautious blasting to avoid blast damage in the remaining rock. Attempts has also been done in order to evaluate what the degree of Swedish cautious blasting has meant for the rock support costs during the construction period.

Jan 1, 1984

By Lyall Workman, P D. Katsabanis

Energy released by the explosive is typically partitioned in brisance, heave and losses. The fact that energy released in the P-V expansion curve below a certain point is lost has resulted in the concept of available energy. Through simple calculations it is shown that energy released at pressure levels thought to be low, amounts to a significant proportion of the total energy value. Furthermore, throw calculations indicate that the assumed loss of that part of energy does not justify practical results. Loss of energy at the low pressure levels may also not be justified from the fragmentation point of view as pressure levels below 1 kbar are enough to extend radial fractures around a borehole. Finally the equation used for the P-V behaviour of the explosive gases is important in throw calculations. Simplified approaches may not reproduce the performance of the explosive which is not characterized only by its energy content.

Jan 1, 1998