Search Documents

By Walter Kawa

Coals of various rank were reacted by the Bureau of Nines in plasma jets generated from argon and argon-hydrogen mixtures containing up to 33 volume-percent hydrogen. Average plasma temperatures ranged from about 3,400° to 12,000° C. Products were a solid residue and a gas containing hydrogen, methane, acetylene, diacetylene, and oxides of carbon. The highest yield of acetylene obtained with argon plasmas was 15 percent by weight of moisture- and ash-free coal. The data indicated that acetylene yields of 40 percent or higher can be obtained from the reaction of coal in argon-hydrogen plasmas, although results from these experiments could not be correlated with operating variables because of low recoveries plasma contained sufficient energy to heat the coal to temperatures as high 9,000 or 10,000° C, but complete devolatilization did not occur in any experiment.

Jan 1, 1966

By D. Bienstock, J. H. Field, M. J. Lempel

A computer program is presented to perform the detailed and numerous calculations required for determining the interface temperatures and steady - state heat flow through a furnace wall composed of several refractories in layers . A method is developed that will allow the designer to determine the various thicknesses for each refractory layer to minimize either the total wall thickness or the cost of the wall per unit of area . A sample problem is presented and analyzed to illustrate the techniques involved .

Jan 1, 1964

By G. E. McElroy

This report discusses the construction and use of an all-pressure psy- chrometric chart in which the requirements of simplicity of appearance and absolute accuracy have been waived, to a certain extent, to provide for the rapid determination of psychrometric data and for the rapid solution of air- conditioning problems of major interest to the mining industry. Many mines in which air-conditioning problems are important are situated at elevations far above sea level and embrace great differences in elevation - in excess of 8,000 feet in certain mines → throughout their airflow circuits. Under these conditions, the effects of variations in the pressure of the at- mosphere upon the physical properties of the mixture of air and water vapor of which it is composed are considerable and should be taken into account in the solution of problems. The simple types of psychrometric charts in common use, such as the Carrier, Bulkeley, Hill, and Goff (American Society of Heat- ing and Ventilating Engineers Guide), are not generally suitable, in that they are drawn for a single barometric pressure 29,92 inches mercury.

Dec 1, 1947

By H. A. Doerner

"The pure mineral chromite, FeO.Cr203, consists of ferrous and chromic oxides, chemically united in equal molecular proportions. Unfortunately, pure chromite as defined above appears to be a rare exception. In most chrome ores the mineral may be considered a combination of spinel, MgO.Al203, and chromite, with the latter predominating. The ratios between the four common constituents Fe0, Mg0, Cr203 and A203 vary greatly, and other minor constituents such as TiO2 and. Fe203 may also be present.In the mechanical concentration of chromite ores the maximum grade of concentrates that can be produced is thus limited by the composition of the chrome minerals present. Pure chromite contains 68 per cent Cr203, but the Cr203 content of the chrome minerals in commercial ores varies between 45 and 60 per cent and the average is not far from 55 per cent.Chromite is usually associated with serpentine. Other silicates, quartz, dolomite, magnetite, ilmenite and other iron Minerals are frequently present.The amenability of a chrome ore to concentration, depends upon the kind and amount of the various gangue minerals present and the amount .of crushing necessary to separate the chromite from them.A relatively small amount of chrome ore is concentrated by milling. In most cases the mine product is simply hand-sorted. Such chrome deposits as are known in the United. States can not be worked in this way on account of one or both of the following conditions: High cost of labor and finely disseminated impurities. There are, however, several deposits in the United States, Canada, and Alaska which may be able to compete with imported or by efficiently utilizing modern ore-dressing and milling methods."

Nov 1, 1930

By J. A. Ruppert, P. M. Sullivan

A study was made of filtration techniques for recovering the major part of the tin contained in iron - tin alloys known as hardhead . Special smallscale filtering apparatus and a three - stage cyclic process were developed . Eighty- seven percent of the tin contained in an alloy of 82 percent tin and 17 percent iron was recovered as pure metal by pressing at 975° C followed by a second pressing at 800 ° C and a final filtering at 250 ° C. Small amounts of Sb , Cu , and Fe impurities were removed by adding Al to the molten product and performing another filtration at 250 ° C.

Jan 1, 1964

By Roy F. Abernethy

All samples tested showed some loss of heating value for the 5-month period under all 4 storage conditions. The losses increased as the time of storage increased, with the pan-storage samples showing somewhat greater losses than those in cans. The individual daily analyses for the first 2 weeks and the analyses every other day for the third and fourth weeks of storage vary within the approximate tolerance of the test for heating value. During the first 2 months of storage the changes in heating values were not Significant for the samples from Pennsylvania, Indiana, and Colorado. The Ohio coal indicated some loss by the end of I month, which increased to a value measurable with certainty by the end of 2 months. These data show that (1) small changes may occur even to samples in closed cans and (2) the laboratory sample should be handled as expeditiously as is practical until the analysis is completed. The statement by the ASTM that "If the B.t.u. determination is an important consideration in the sale of coal, the time elapsed between sampling and analysis shall not exceed 30 days,"3/ is quite adequate for 3 of the 4 coals tested. The change in the Ohio coal stored for 30 days is merely indicated and could not be determined with certainty by the techniques normally employed. The data on free-swelling indexes determined on can samples, after 30° C. air drying, show that only the Indiana coal lost more than one unit in free-swelling index number in 120 days. No significant changes were observed with the samples from Pennsylvania, Ohio, and Colorado in the 5-month period.

Jan 1, 1958

By Oliver Q. Leone

The effect of oxygen content in the anode metal on titanium electrorefining characteristics was studied. Increasing quantities of oxygen in the anode resulted in increased anode scale formation, decreased anode and cathode current efficiencies, lower titanium recovery efficiencies, and higher oxygen content of the cathode products. The titanium electrorefining process performed best when the anodes did not contain more than 0.5 percent oxygen, although anode dissolution was recorded for alloys containing up to 25 percent oxygen. Back emf affords a useful index of an alloy to electrorefining.

Jan 1, 1965

By Gabriel S. Esterhuizen, Jarek Jakubec

In 2000, Laubscher’s Mining Rock Mass Rating (MRMR) classification system was updated and published. The new system brought a few fundamental changes that were in direct response to the challenges and problems encountered when applying the classification system in the mining environment, specifically caving operations. The fundamental changes introduced into the MRMR system in 2000 were the abandonment of the Rock Quality Designation (RQD) as an input parameter, accounting for healed and cemented joints, and the concept of rock block strength. The objective of this paper is not to discuss the role and usefulness of classification systems; the fact that classification systems are widely used in every stage of mining projects speaks for itself. This paper discusses some of the experiences gained with the MRMR 2000 system in various mining projects and shows how the changes to the system have resulted in improved assessment of rock mass conditions. Issues related to core logging for rock mass assessment are also presented.

Jan 5, 2007

By W. H. Eddy

The Bureau of Mines conducted laboratory batch flotation tests and continuous pilot plant flotation tests on a complex calcareous fluorspar ore from Cave-in-Rock, Ill., to determine the technical feasibility of producing commercial-grade concentrates by the sodium fluoride-calcium lignin sulfonate-fatty acid method of concentrating fluorspar previously developed by the Bureau. The continuous flotation tests, treating about 150 pounds of ore per hour, produced fluorspar concentrates assaying 96.4 percent CaF2; 90 percent of the fluorspar was recovered.

Jan 1, 1967

By R. K. Koch

The vapor pressures of liquid titanium and liquid platinum were studied under the Bureau of Mines program for the determination of thermochemical data on the transition elements. Beating was done in a 2-kw electron-beam furnace with a water-cooled copper crucible to contain the melt. Temperature was measured with a disappearing-filament brightness pyrometer. The vapor pressure data for liquid titanium in the range 2,008° to 2,379° K are represented by the least-squares derived equation [log p (atm) = 6.268 - 22, T] Two series of determinations were made on liquid platinum. Results of the first series are expressed by the least-squares derived equation [log p (atm) = 8.240 - 30,460T] for the range 2,0860 to 2,4200 K. Results of the second series are expressed by the least-squares derived equation [log p (atm) = 7.795 - 29,580 T] in the range 2,045° to 2,442° K. Third-law evaluations of each series gave mean standard heats of sublimation of 112.4 kcal/mole, 133.3 kcal/mole, and 133.8 kcal/mole for titanium first series on platinum, and second series on platinum, respectively. Second-law heats of sublimation and equations for heats, free energies, and entropies of vaporization were obtained from sigma plots of each data set.

Jan 1, 1969

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Galis Mfg. Co. face drill. The instructions are based upon an actual installation made in the mine on face drill model 460-S. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other face drills with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other face drills and can determine any necessary modifications if they are not.

Jan 1, 1973

By L. A. Panek, A. J. Barry, John A. McCormick

"INTRODUCTION During recent years, roof bolting has become widely accepted as a systematic method of supporting both coal- and metal-mine roofs. Today, over 2 million roof bolts are installed monthly. Most of the information on bolt installation procedure reported to date (1,2,3,4,5,6) 3/ has been obtained by trial and error by individual groups or operators. To insure good roof control, experience and field tests have indicated that roof bolts should be installed immediately after the exposure of new roof, and they should be preloaded enough to minimize sag of the roof over the opening. The question of the proper initial preload for roof bolts is under study, although it is a general practice to impose an initial load on a bolt of approximately 10,000 pounds. This created a problem of measuring bolt loads at installations in underground mines, which was partly solved by using a commercial-type torque wrench; a device that permits a direct reading of the torque applied to the nut on a roof-bolt assembly from which the corresponding load can be determined by referring to specifications furnished by the manufacturers. However, considerable apprehension was expressed regarding the accuracy of this measuring procedure because of variations in the manufacture of roof-bolting materials and the degree of care exercised in making bolt installations. In the process of loading a bolt, only a small part of the effort is expended in producing strain in the bolt - the larger part of the effort is used in overcoming frictional effects in the nut-bolt-washer assembly. These frictional effects are subject to many factors, such as condition of threads, type of lubrication, if any, the finish on the nut and bearing plate, and the alinement of the bearing plate on the bolt. The object of this investigation was to determine the accuracy with which the load developed in a slotted-type roof bolt installed in a conventional manner in shale or sandstone roof rock can be determined from the torque applied to the nut.This report is the first of a series relating to basic research in roof bolting in underground mines. A future report will cover results obtained using expansion-type bolts under similar conditions. Other reports will consider the efficiency of bolt anchorages, the long period stability of bolts, and the design of safe and efficient roof-bolting systems."

May 1, 1953

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This article focuses on U.S. Bureau of Mines (USBM) and National Institute for Occupational Safety and Health (NIOSH) research to examine factors that had a significant influence on mine face ventilation design during the past century. Several "milestone" events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative face ventilation designs and a consistent commitment to mining health and safety. Ventilation has always been a concern in underground coal mining. For many yeas, there was no appreciation of how ventilation could be used to remove harmful contaminants from the air or how to control airflow quantities. The first known problems with ventilation date back to the 14th century, when it was recognized that lack of air was a major impediment to the expansion of mines. The common method of solving ventilation problems at that time was to abandon the existing mine and start a new one nearby. Ventilation in the early days of coal mining was accomplished by means of a natural draft, created principally by a difference in the weights of columns of air between the intake and return openings. Later, in the 18th and 19th centuries, a furnace was introduced underground to increase the updraft in the return shaft. This allowed for a larger quantity of air in circulation. When mines went deeper and became larger, mechanical ventilation became necessary and was first accomplished by steam-driven fans. These fans became more prevalent as furnaces were prohibited in underground mines, especially after the Avondale disaster in Pennsylvania in 1869 (Roy, 1876). Eventually, these fans were replaced by more powerful, electrically [ ]

By Lucia Kuizon

The Antimony RARE II area is underlain principally by Mesozoic igneous rocks associated with the Sierra Nevada batholith. The San Andreas fault zone is near the southern boundary. Metallic mineral deposits are associated with the fault zone. These deposits were formed from magmatic solutions, and tend to be along shears and fractures within the country rock. Marble and dolomitic marble deposits occur in Paleozoic roof pendants or inclusions in the Mesozoic intrusive rocks in the area (Troxel and Morton, 1962, p. 52).

Jan 1, 1982

By H. L. Riley

At the Southern Experiment Station, Tuscaloosa, Ala., reports are prepared from time to time on results of washability studies of coal from important beds in the Southern Appalachian region. The investigations that provide the material for these reports are made by the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and the mine operators. The principal objective of a washability study is to obtain technically and commercially important data to aid in determining the best methods for preparing and utilizing the Nation's reserves, particularly of coking coals. Such information is also important from the standpoint of conservation, because it facilitates the selection of preparation methods that will yield an acceptable product with a minimum loss of coal to the rejects.

Jan 1, 1958

This paper describes the sinking and lining of a 14 foot 6 inch finished diameter shaft down to and into the salt of a typical dome of the Gulf States region. The conditions and nature of the strata encountered divide the work into three distinct sections - that in (1) alluvial surface deposits, sunk through by open caisson methods, (2) water bearing rock, directly above the salt, and in (3) salt. ACKNOWLEDGMENT The writer wishes to acknowledge the cooperation of the sinking contractors, The Dravo Contracting Co. of Pittsburgh, Pa., through E. T. Gott, vice-president, in furnishing the data used in this paper.

Jan 1, 1932

By W. H. Coghill, B. W. Gandrud, F. D. DeVaney

"The self-fluxing iron ores of Alabama are the foundation of the thriving iron and steel industry of that State. In addition to these deposits of self fluxing ores there are seams containing practically the same percentages of iron but too much silica. These ores at present are valueless, but if they could be concentrated by reducing the silica content, the ore reserves of the Birmingham district would be greatly augmented. A detailed report on the iron-ore deposits of the district, describing the types of ore and their extent, has been published.In forwarding its mineral conservation policies the United States Bureau of Mines has given some attention to the siliceous ores of this district.The low cost of gravity concentration gives this process first rank in the beneficiation of iron ores. For this reason many experimenters have tried to concentrate the Alabama iron ores on tables. In the face of the early failures a new trial has been made and the results have justified the effort.In this work more attention than formerly has been given to the physical, properties of the ores. The removable siliceous gangue is in the form of oolitic grains which ""shell"" out like corn, leaving the hematite as rich high-grade ""slime"" and as clean granular grains. The ""slime concentrate"" may be recovered by well known desliming processes. The oolitic grains and granular hematite are separated on tables."

May 1, 1929

By R. V. Subramanian

This project financed by the Bureau of Mines investigated the use of polymers to achieve rock bonding and reinforce coal mine structures for better or permanent ground support. Support was achieved by pumping the polymers into the rock interstices to bond the mass together for increased structural competence. Holes were drilled in the mine roof, after which the polymers were injected at about 100 psi to permeate the cracks. Initial laboratory work indicated that of all the resin systems tested, the epoxy resins could most likely be modified to be suitable for rock injection. This was confirmed when several potentially suitable resin systems underwent intensive evaluation. In a series of three field tests, two conducted in a copper mine with coal mine-type shale and the third in a coal mine, it was shown that the polymers penetrated cracks less than 0.005 inch wide. The fast-setting epoxy systems, cured out in thin films under mine conditions, produced a bond exceeding the strength of the uncracked virgin rock.

Jan 1, 1974

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Bolivia has been prepared from the best available information in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State. SYNOPSIS OF LAW All useful substances of the mineral Kingdom belong originally to the State. The soil and subsoil are regarded as two distinct parts, the latter extending indefinitely in depth (Art. 2). The subsoil is under the dominion of the State, which may either abandon it to common use, grant it gratuitously to the owner of the soil, or alienate it, in return for an annual fee, to any individual or association that applies for it. (Art. 1-3.)

Jan 1, 1929

By M. Karmis

Surface subsidence is an inevitable consequence of many underground mining operations and has been recognized as such since the fifteenth century. Damage resulting from this phenomenon ranges from simple land settlement to severe structural damage to buildings and has been witnessed in rural (Illinois, Colorado, West Virginia, Virginia, Pennsylvania) as well as in urban areas (Pennsylvania, West Virginia, Illinois, Wyoming). In fact, it is estimated that over 2 million acres of land across the United States have been affected by mining subsidence, of which 140,000 acres are in urban areas (Singh, 1978; Johnson and Miller, 1979). Further, it is estimated that during the next twenty years an additional 1.5 to 2.4 million acres of land will also be affected by mining. Subsidence prevention is not feasible, at least under the existing technologic and economic constraints of underground coal mining. Foreign experience has demonstrated, however, that subsidence can be successfully controlled if an accurate method of predicting ground movements is available. Such techniques have been developed in many coalfields, where it is currently accepted that subsidence can be predicted within ± 20 percent of the actual values. Furthermore, such movements can be translated into anticipated structural failures using established damage criteria, thus enabling appropriate precautionary measures to be implemented.

Jan 1, 1983