Search Documents

By N. Grosland, G. Kopp, T. Hunstad, D. Wilder, M. Contratto, S. Rahmatalla, T. Xia

Chronic whole-body vibration exposure, as expected in large construction and mining vehicles, has been associated with neck and back pain and injury.1 While work has been done towards gaining a better understanding of the relationship between vibration and shock and muscle activity of the back musculature2, relatively little information regarding the activity of neck, shoulder and upper arm muscles is known. Today’s equipment designs must conform to domestic and international standards, however these standards do not specifically address the vibration exposure in the head and upper quarter. Further it is not well known how the control configuration within a vehicle (e.g. steering wheel versus arm controls) influences muscle voluntary and reflex activity levels. Greater muscle activity may lead to greater muscle fatigue – which in turn may be associated with greater risk of injury.2 Thus, muscle contractions needed to maintain static postures as well as those resulting reflexively should be considered during an analysis of seating position. Unfortunately, little is known regarding the influence of arm position on head and neck muscle function. The purpose of this study was to investigate the relative muscle activities of 5 neck, shoulder, and upper arm muscles during riding simulations of large construction equipment, using three different arm control options. Methods Five typical heavy equipment ride files were “played back” through a man-rated Servo Test 6-degree of freedom (dof) vibration system. Each ride was repeated using 3 seat and control configurations (steering wheel (SW), floor mounted arm-rest controls (FM), seat mounted arm-rest controls (SM)). Two trials were performed for each ride and seat control combination (each trial: 60 sec of 6-dof and 60 sec of vertical vibration). Five channels of surface electromyography (EMG) of the right-side cervical erector spinae muscles (neck extensors), sternocleidomastoid (neck flexor), upper trapezius (shoulder elevator), biceps brachii (elbow flexor) and triceps brachii (elbow extensor) muscles were collected throughout each ride (~ 2min) using pre-amplified (10x), 1 cm silver bar electrodes, with 1 cm fixed inter-electrode distances (Delsys, Inc). Further analog amplification was set at 10k (1k for one subject), and sampled at 1000Hz using a 12-bit DAQ card and Labview 7.1 software (National Instruments). A total of 7 right-handed male subjects were tested, but only 5 had complete EMG data sets to analyze for this sub-study. EMG was analyzed using root mean square (RMS, in mV) of 20 ms moving windows, and then averaged across the entire trial for a measure of mean total muscle activity (voluntary and reflexive). The muscle activity to maintain the static posture was estimated as the mean RMS EMG over a 1 sec interval just prior to and/or after completion of the ride. Repeated Measures ANOVAs were used to test for with-in subject differences using a = 0.05.

Jan 6, 2006

By Eric R. Bauer

This Bureau of Mines manual is intended to provide a better understanding of ground movement and the technology available for measuring it, The manual deals with convergence, strata separation, lateral roof movement, stress, and support load in underground mines. The instruments that measure these ground control parameters are described in detail. Step-by-step procedures for selecting the appropriate instrument are presented, which consider such factors as approximate cost, installation procedures, data collection, and data interpretation; and an instrument selection worksheet is provided to facilitate the instrument selection process. Actual instrument case studies and a list of instrument suppliers are presented in the appendixes.

Jan 1, 1985

By M. Howard Berliner

In August 1943 the Bureau of Mines completed seven churn-drill holes in an area of old mine workings near Linden, Wis., formerly known as the Argall mine. The work was undertaken as part of a general investigation by the Bureau of the zinc and lead producing area of southwestern Wisconsin at a time when special effort was being made to increase the production of metals necessary for war. The area was selected for investigation on the basis of its favorable geologic structure, past history, and apparent mineralization.

Jan 1, 1948

In This Chapter [Finding the dust source Ventilation and dust collector malfunctions Upgrading the dust controls Design stage ventilation planning ] This chapter explains how to reduce respirable dust76 in hard-rock tunnels during excavation by using tunnel boring machines (TBMs). The first steps in combating a dust problem are to take dust samples to pinpoint the source, check the ventilation system, and check the dust collector. If the ventilation system and dust collector are operating properly, then other dust controls such as water sprays and conveyor belt scrapers must be upgraded. For tunnels in the design stage, recommended air quantities are provided. FINDING THE DUST SOURCE AND LOOKING FOR VENTILATION MALFUNCTIONS [The first steps in fighting a dust problem are to take dust samples to pinpoint the source, check the ventilation system, and check the dust collector. Without knowing the exact source, efforts to reduce dust are hit-and-miss (mostly miss).] Taking samples to pinpoint the dust source. In tunnels with high levels of airborne dust, the first task is to pinpoint where the dust enters the airstream. Most dust originates from rock breakage at the tunnel face, but the location where this dust enters the airstream can vary. Dust can leak from behind the TBM face shield, from gaps in the ventilation duct, or from a mal-functioning dust collector. It can be entrained into the air from the muck on a moving conveyor belt. It can even be shaken loose from the underside of the belt as it passes over the idlers. As a start, to locate the dust source, dust samples and air quantity measurements should be taken at the following locations:

Jan 6, 2003

By P. -É. Boileau, VibRG, S. Grenier, M. Smets, T. Eger, J. Stevenson

Load-haul dump vehicles (LHDs) are used to move waste rock and ore in underground mining operations. The LHD is designed for bi-directional operation and the driver sits sideways to the direction of travel. LHD operators have higher reports of low back pain and neck discomfort than other mobile equipment operators who do not sit sideways in the vehicle, but are exposed to whole-body vibration (WBV)1. Exposure to WBV is linked with reports of lower-back pain, neck problems and spinal degeneration2,3. Static sitting postures, sitting with the neck and back twisted, and sitting with the back in an unsupported posture are also linked with an increased risk of developing back pain4. The objective of this study was to determine typical vibration exposure levels and driving postures for LHD operators. Methods Whole-body vibration exposure was measured at the seat-pan, in accordance with the ISO 2631-1 standard5, on seven LHD vehicles with a 10 yard bucket haulage capacity. Vibration data were recorded with a Biometrics™ DataLog II (P3X8) and stored on a 128 Mb Simpletech™ multimedia card. Comparisons were made to the ISO 2631-1 Health Guidance Caution Zone (HGCZ) in order to determine potential injury risk. Operator posture was monitored with three digital video cameras which were secured inside each operator’s cab to the top left corner, top right corner and back right corner. Reflective tape was placed on each driver’s shoulders, head, and back in several locations and in several locations on the vehicle seat in order to aid in posture coding. Posture coding was performed with 3DMatch v4.50 multiple video view analysis feature. Vibration measurement and posture recording occurred simultaneously for 60 minutes while the LHD operator performed typical duties. Results and Discussion Results indicate LHD operators may be exposed to whole-body vibration levels putting them at risk for injury (Table 1). According to ISO 2631-1 the frequency weighted acceleration values corresponding to the lower and upper limits of the HGCZ (for an 8 hr exposure duration) are 0.45 and 0.90 m/s2 respectively5. Six of the seven vehicles showed exposure levels within the HGCZ defined for 8 hours. Preliminary video analysis indicated LHD operators were exposed to potentially harmful levels of WBV while adopting asymmetric postures (Table 2). For example, one LHD operator (Figure 1) worked with his neck twisted greater than 40 degrees for 93 % of a 60 minute work cycle. According to the Swedish National Work Injury Criteria, neck rotation should be less than 15 degrees if the motion is required for greater than 80% of the work time6. Results of this study highlight the need to further examine the contribution of non-neutral working postures and

Jan 6, 2006

By W. P. Yant, C. E. Traubert

"INTRODUCTION Canister-type gas masks have become an essential part of the equipment of many industries, not only for use in emergencies, but also in performing normal operations of industrial processes and procedures, particularly where ventilation is not practically or economically feasible. They are also used widely for enhancing safety of operations which previous to the development of gas masks had been performed in harmful atmospheres.Since the inception of industrial gas masks the Bureau of Mines has been actively engaged in endeavoring to increase the efficiency and safety of these devices, and this bureau has become a source of advice to manufacturers in producing devices of good quality and to industry in the proper selection and use of these devices. In order to give first-hand information and keep current with the demands and needs of industry it is necessary to perform investi-gations from time to time. This report deals with tests of certain types of commercial gas-mask canisters for protection against mercury vapor.TYPES OF CANISTERS EXAMINEDThis investigation included tests of the following types of canisters:(a) Gas-mask canister filled with 725 c.c. of granular activated charcoal, 8 to 14 mesh, and of a quality used in gas masks which meet the Bureau of Mines approval requirements 4 for protection against organic vapors."

Oct 1, 1932

By Sean Gallagher

The vast majority of ergonomics research has addressed the demands of work in standing or sitting postures, and understandably so. However, many workers (for example, underground miners, aircraft baggage handlers, plumbers, agricultural workers, mechanics, and others) are often required to adopt postures such as kneeling, stooping, squatting, or lying down for significant periods of the work day.

Jan 1, 2005

By Claud Johnson, G. Roger Miller, Kristine M. Krajnak, Stacey Waugh, Oliver Wirth

Workers exposed to vibrating hand tools are at risk of developing symptoms such as cold-induced vasospasms, loss of tactile sensitivity, and loss of grip strength in the fingers and hands. These symptoms are known collectively as vibration white finger (VWF) or hand-arm vibration syndrome (HAVS). Symptoms of VWF or HAVS are in part due to repeated and prolonged peripheral vasoconstriction[1, 2]. The reduction in blood flow that occurs with vasoconstriction can result in oxygen deprivation (hypoxia) in soft tissues, such as nerves and muscle, and lead to functional and structural changes in these tissues. The present study examined muscle tissue to determine if vibration-induced changes in transcript levels and protein concentrations result in enhanced vasoconstriction and hypoxia. Manual dexterity was also assessed intermittently to determine if vibration-induced changes in cellular factors are accompanied by performance deficits. Methods An animal model was developed to study the biological and functional changes that occur in response to repeated segmental vibration exposures. In this model, the right paw of intact rats was exposed to a platform vibrated at a frequency 250 Hz and amplitude of 49 m/s2 to simulate the vibration characteristics of hand-held grinders. Three groups of 8 rats each were studied: a vibration-exposed group, an exposure-control group, and a cage-control group. Exposure sessions, with or without vibration, were conducted 4 hr/day, 5 days/week for 5 weeks. Manual dexterity was assessed intermittently during the 5-week exposure period with the Montoya stair-case test[3], which quantifies the rat’s ability to reach for, grasp, and retrieve small food pellets placed below the rat on different levels or steps. Following the 5-week exposure period, the flexor muscles of the right forelimb were collected for analysis of gene expression, protein concentrations, and immunohistochemistry. Results Vibration-exposure resulted in an approximate 2-fold increase in the expression of a2C and a1D receptor transcripts in flexor muscles (Figure 1). These receptors mediate norepinephrine-induced vasoconstriction in smaller arteries. Vibration-exposure also resulted in an approximate 2-fold increase in hypoxia-induced factor-1a (HIF-1a), a transcription factor that is expressed in response to tissue hypoxia. Western analyses demonstrated that restraint caused a decrease in a1-receptor protein concentrations in the flexor, but vibration-exposure prevented the restraint-induced reduction (Figure 2). Immunohistochemistry performed on flexor muscles (not shown) demonstrated that a1 receptors are primarily located in arteries; maintained levels of these receptors could contribute to prolonged vasoconstriction following repeated vibration exposure. The staircase test showed some performance improvement, or a training effect, in manual dexterity for the control groups but not the vibration-exposed group (Figure 3).

Jan 6, 2006

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

The Federal Coal Mine Health and Safety Act of 1969 has dictated major changes in mine ventilation with regard to both air quantity and quality. Requirements have also been placed on the ventilation of beltlines, gob and face areas, and air velocities on trolley haulage roads are limited. Escapeways, separate from trolley haulage roads and on an intake split of air, must be maintained continuous to the surface. These and other similar requirements have not only precipitated several modifications to existing ventilation systems but also have greatly increased the complexities of new mine ventilation planning. It is apparent that the use of computers in ventilation system analysis and design is a necessity. SUMMARY Although computer oriented analysis of mine ventilation systems was introduced over two decades ago, it has yet to receive widespread acceptance in the United States. Central to this problem is the fact that, while many computer programs for network analysis have been developed, no attention has been paid to the development of computer input data. Consequently, without this foundation, program applications have been infrequent. This thesis has directly attacked this problem and has presented all pertinent information basic to the development of good computer input data. The areas that were covered include quantity measurement, pressure measurement, fan testing, survey data balancing, and the development of a network schematic from the ventilation survey results. These discussions on data collection and the corresponding reduction to computer coding have been illustrated by an application of a ventilation simulation program to an existing mine in Southwestern Pennsylvania. The use of a ventilation

Jan 1, 1977

The coal-bearing strata of Oklahoma occur in the eastern part of the state over an area of 14,500 square miles, 20.7 percent of the state's total area. Commercially valuable deposits of bituminous coal cover about 8,000 square miles in seams ranging from ten inches to five feet thick. Estimated reserves in Oklahoma are 1.6 billion tons, representing 0.3 percent of U.S. coal reserves. The vast majority of coal mined in Oklahoma used in a single power plant within the state. Oklahoma gained primacy when its regulatory program was conditionally approved January 19, 1981. Authority for the state to administer the Abandoned Mine Land program was granted January21,1982. On April 30,1984, the Office of Surface Mining substituted direct federal enforcement of the inspection and enforcement portions of the Oklahoma program. This substituted enforcement was based upon a finding by OSM that Oklahoma had not operated the inspection and enforcement portions of its program effectively. As of January 1, 1986, Oklahoma inspection and enforcement authority was reinstated. Full program authority was granted to Oklahoma on January 14, 1986.

Jan 1, 1992

By Chi-Mun Song, Seok-Hyun Choi, Seok-In Hong, Han-Kee Jang

Accurate measurement and evaluation of hand-transmitted vibration from a power tool is an important issue for tool manufacturers, because they are obliged to develop low-hazard power tools for workers. The International Standard ISO 5349(1) dictates a systematic procedure for the measurement and evaluation of hand-transmitted vibration. However, the uncertainty in this measurement is too large for manufacturers to apply such data to the design and modification of power tools. There can be several sources of this uncertainty in such measurements; e.g., operator-dependent, power tool-dependent, and operational conditions (see Table 1). For a manufacturer to characterize the exposure of a power tool’s use to a given level of vibration, the relationship between these uncertainty factors and the measured vibration must be elucidated. In this study, we investigated the effect of several factors on the uncertainty in measurements. [ ] Methods In this study, some of the factors in Table 1 were selected for examination, and their effect on the measured variation was quantitatively investigated. Three tools from the same manufacturer were sampled at random in our experiments, and each of five of the same type of insert (disks or tips) was installed into each tool. Although each of the tools and inserts were of the same design and were made by the same production process, they differed from one to another, which can be a source of the variation in the measured vibration. Three human subjects participated in our experiments, which were carried out as stated in ISO 5349. The subjects were asked to maintain their posture, and the applied force was kept as constant as possible. The applied force was monitored using an indirect method, where vibration energy was displayed in real time during the experiment using a three-axis accelerometer attached to the work piece at a specified point. The appropriate range of the applied force was predetermined to cover the range of real work operations. The engineering tolerance between the inner diameter of a grit disk and the outer diameter of the tool shaft leads to an eccentricity of the mass at the center of the disk. The degree of eccentricity varies with installation, and this is another source of uncertainty. In our study, the effect of this eccentricity was investigated by carrying out repeated assembly and disassembly of an insert.

Jan 6, 2006

By L. A. Stewart

This is one of a series of reports prepared by the Federal Bureau of Mines on mining methods, performance, and costs at individual mines in the United States. The primary purpose of these papers is to promote development and conservation of our mineral resources by disseminating technological information on methods, practices, and results that may be applied to the engineering analysis and solution of mining problems. This report discusses the highly selective mining methods of the Jaquays Mining Corp. at the Regal asbestos mine, 45 road miles northeast of Globe, Ariz. The milling method at the Globe plant is discussed briefly, and the extraction ratios of the various grades of fiber are tabulated. The proposed flowsheet of a new mill under construction is shown.

Jan 1, 1961

By David C. Grant

A laboratory technique for simulating in-situ uranium mining was developed and used to determine the effects of leaching variables on permeability, uranium recovery, leach solution interaction with the ore-aquifer environment, and post-leach chemical leakage. In particular, ammonium bicarbonate, the commonly-used leach solution, was examined in great detail. Agitation leach tests were conducted to examine the effect on ammonium sorption and desorption of clay content, solution and clay ammonium levels, pH, and the type and concentration of other anions and cations in solution. Initial column tests were performed to determine the degree of ore-aquifer interaction that could be expected for various leach solutions; sulfuric acid, and ammonium, sodium, and potassium bi-carbonates. Subsequent tests examined various methods to restore the ores by lowering the post-leach chemical leakage. The restoration tests examined the use of reducing agents (e.g., ammonium bisulfite, sodium bisulfite; and sodium sulfite), ore blocking and stabilizing agents (e.g., sodium silicate, aluminum chloride, and magnesium-calcium salt).and ammonium displacement agents (e.g., aluminum chloride and lanthanum chloride-sulfate)

Jan 1, 1980

By Alan Mayton, Bertrand Valero, Christopher Jobes, Farid Amirouche

Exposure to vibration induced in and around underground mine’s exploration is a major concern to vehicles operators. Most of these drivers over time develop serious spinal musculoskeletal and discs problems causing low back injuries. The first purpose of this paper is to analyze the performance and dynamic response of driver/operator when subjected to different levels of vibration due to rough road conditions depicted in a mine field. The second purpose of the paper is to quantify the energy transmission in the presence of seat padding with special characteristics and active suspension. Using experimental testing data collected at NIOSH/PRL (National Institute for Occupational Safety and Health/ Pittsburgh Research Laboratory) along with model simulation algorithms developed at the University of Illinois at Chicago we investigated how acceleration transfer functions as well as absorbed power affects the different parts of the body. To this end, we used a previously validated human model which includes the head, torso segments and legs. The connective forces between body segments were modeled through modal analysis techniques from previous experimental data at the UIC Vehicle Technology Laboratory. The absorbed power and energy transmitted to the body are used as an index measure to assess the viability of the different seat padding’s and active seat suspension control strategies.

By Allen D. Look

Uninterrupted shaft operations are an important economic factor in mine operation, and good shaft support is an important aid in preventing accidents and interruptions. More permanent supports can cut the hazards, costs, and delay incident to replacement of conventional timbers, especially where subject to decay. Installation of prestressed, precast concrete shaft supports in 100 feet of shaft at the Banner mine, Lordsburg, N. Mex., nave a satisfactory permanent installation in a section of shaft that had given trouble with conventional timbering. Use of rock bolts supporting gunited wire netting around the rock walls of the shaft prevented sloughing. No attempt was made in this paper to arrive at comparative costs of installation of various types of support. However, it was indicated that use of a lighter weight aggregate would be desirable in further use if prestressed precast members as placed in the Banner mine.

Jan 1, 1957

By A. W. Deurbrouck

This report describes the preparation characteristics of the significant coalbeds from which samples could be obtained in Webster County, W. Va. In 1964, approximately 825,000 tons of coal was produced in the county, of which 732,000 tons was mechanically cleaned in three preparation plants. The Sewell coal bed accounted for 94 percent of the coal produced. Twelve samples were collected from five coalbeds. Four of the samples would require upgrading to meet metallurgical requirements; two others of just over 8.0 percent ash would require some upgrading. In general the coalbed samples collected in the county were of medium-sulfur and medium-to low-ash content as received or after removal of the sink 1.58-specific-gravity material.

Jan 1, 1966

By Laurence G. Trudell

A geologic framework for interpreting stratigraphic and geographic variations of the Green River Formation in the Piceance Creek Basin is developed from lithologic data accumulated by the Bureau of Mines from oil-shale coreholes. From detailed Bureau of Mines descriptions of samples from nine coreholes and supplementary lithologic data from seven additional sampled sections, three cross sections were constructed along lines transecting the basin. Plotted as lithologic columns with corresponding oil yields and resistivity logs, the sampled sections are correlated on a time-stratigraphic basis. Distribution and correlation of nahcolite and halite zones are shown, and the approximate base of leaching of these saline minerals is indicated. General lithologic characteristics of members and zones are discussed and interpreted. Large-scale lithologic logs illustrate the nine Bureau of Mines core descriptions, and the complete description of Bureau of Mines-Atomic Energy Commission Colorado Corehole No. 1 is included in an appendix. The time-correlated cross sections provide a necessary framework for understanding the depositional history of the Green River Formation and will facilitate evaluation of oil shale and other mineral resources in the Piceance Creek Basin.

Jan 1, 1970

By Jozef S. Stachulak

In This Chapter [Ore pass dust control Drill dust control Blasting dust control Conveyor belt dust control Transfer point and crusher dust control Roadheader dust control and How much ventilation air to use] This chapter discusses respirable dust control in underground hard-rock mines. These mines use a wide variety of extraction methods, but they have many common dust sources and dust control needs. Ore passes, drills, blasting, conveyor belts, transfer points, crushers, and load-haul-dump operations can be major sources of dust. Roadheaders, which are sometimes used in hard-rock mines, produce dust in large quantities. For the most part, dust in hard-rock mines is controlled with ventilation air, water sprays, and dust collectors. It is also important to prevent dust from getting into the air in the first place. Good dust control practices will reduce overall mine ventilation requirements. [Lack of maintenance is the main source of dust problems in hard-rock mines according to Rodgers [1974], who conducted a dust survey of hard-rock mines several decades ago. Rodgers found that spray systems had clogged sprays, dust enclosures had improperly fitted skirts, and ductwork was plugged and had leaks. Today’s mines have better maintenance programs (we think), but when dust levels are high, maintenance is still the first topic to address.] The Mining Association of Canada [MAC 1980] and Knight [1980] provide good general information about hard-rock dust control. For conveyor belt dust control, Goldbeck and Marti [1996] and Swinderman et al. [1997] are valuable sources of information.

Jan 6, 2003

By S. P. Howell

The Bureau of lines as repeatedly called attention to dangerous practices in the transportation and opening of kogs of black blasting powder. In 1914 Diwin Higgins (Prevention of Accidents from Explosives in Metal inos, Miners' Circular 19, Bureau of Mines, p. 15) stated "canisters should always be opened by removing the bung. To use a pick or other sharp tool for cutting a hole in the canister is dangerous. After the necessary amount of powder has boon taken out, the canister should be kept closed. The powdor should always be handled at a safe distance from an open light." In 1919, Geo. S. Rice (onthly Statement of Coal line Fatalities for June, 1919, Bureau of Mines, pp. 16 to 18) calls attention to the dangers that arise in underground transportation and handling of explosives, and calls special attmtion to the danger of hauling explosives in motor trips; the unnecessary risk involved in hauling men on the trip at the same time, and the necessity of keeping open lights away from black blasting powder. In 1919 the writer (Sensitiveness of Explosives to Frictional Impact, Tech. Paper 234, Bureau of Mines, pp. 13, 15) called attention to the fact that black blasting powder is not as sensitive to frictional impact as the nitro-glycerin dynamites and the gelatin dynamites. Black powder may be ignited by direct impact and the writer believes that this may occur without presupposing a preliminary spark. It is well known, however, that black blasting powder is very sensitive to ignition by spark flame, or heated materials, and these may be produced by an electric current, by an open light, by incandescent particles from a pipe, cigar, or cigarette, by the tearing of metal sheets or scraping of metal against metal, and possibly, by other means. -- The above discussion will serve to introduce a newly recognized hazard the ignition of black blasting powder by the forcible opening of kegs with wodden tools. The details of three accidents in which kegs of black blasting powder ex- ploded instantly when a wooden tool was driven forcibly through the top of the kegs are as follows: 1. In 1915, a powder man employed by a coal mining company stated that he was opening a 25-pound log of black blasting powder by driving a hole in the top with a wooden sprag when the powder in the leg ho was opening ignitod. This caused the ignition of fifty-two additional 25-pound logs of the powder, and the fatal burning of this and another powder man. The ono making this statement lived five hours after the explosion.

Sep 1, 1920

By Launa G. Mallett, Jr. Brnich

Overview: The first step to emergency preparedness and maintaining a safe workplace is defining and analyzing hazards. Although all hazards should be addressed, resource limitations usually do not allow this to happen at one time. Risk assessment can be used to establish priorities so that the most dangerous situations are addressed first and those least likely to occur and least likely to cause major problems can be considered later. Purpose: This training package was developed to assist instructors as they (1) determine how to use risk assessment to improve safety preparedness and (2) present risk assessment concepts and tools to trainees. The concepts and tools presented here can be applied to any mine hazard.

Jul 1, 2003