Search Documents

By Oliver Bowles

Accidental explosions in coal mines are due to various causes, but many of them can be directly attributed to coal dust; others that probably in no way depend on dust as a primary cause are propagated, greatly intensified, and made more disastrous by the presence of coal dust. The fact that coal dust in a bituminous mine will explode as a result of a fire-damp explosion has been generally accepted for many years, but the belief has also been held by many that coal dust is not in itself dangerous when unmixed with an explosive gas. Therefore, in past years little attention was given to dust in mines free from fire damp, and many disastrous explosions have resulted from lack of knowledge of the danger from coal dust. In the explosives gallery and experimental mine of the Bureau of Mines experiment station, Pittsburgh, Pa., it has been proved repeatedly and conclusively that coal dust will explode violently when no inflammable gas is present. PROPAGATION OF DUST EXPLOSIONS A coal-dust explosion is an extremely rapid burning or combustion of the coal particles. Their burning consists essentially of the combination of the hydrocarbons in the coal with the oxygen of the air, a process that generates heat and flame and produces hot gases and water vapor. These gases and vapors have a volume many times that of the original coal particles; thus they exert an outward motion and pressure which constitute the explosive wave. When fine particles of coal are suspended in the air, each particle is surrounded by the oxygen of the air, and thus is well placed to oxidize or burn rapidly whenever the temperature is high enough. If some particles are ignited from any cause they will fire others, and the combustion will extend from particle to particle with extreme rapidity wherever enough coal dust of sufficient purity is present.

Jan 1, 1925

By J. J. Forbes

The original organic act establishing the Federal Bureau of Mines in 1910 and the amended act of 1913 indicated that promotion of the health and safety of mine workers was to be ore of the chief functions4/ of the Bureau. Many of the field and laboratory studies pursued by the Bureau are designed to improve conditions under dish minors must work. As the Bureau has no legal authority to enforce safety rules, it must rely upon cooperation of employer, employees, State mining or other departments, and labor organizations for success in promulgating its finding and making recommendations. The staff of the Safety Division, which is essentially a service organization of the Bureau, is composed of 28 safety instructors, 29 engineers, 18 clersk, and 7 others engaged in promotion of an educational program in an effort to improve conditions in the mining industry. The work is directed from 14 safety stations in the United States and 1 in Alaska. The work of the personnel, of the mine safety car that operates in. the anthracite region of Pennsylvania was supervised and directed by the district engineer in charge of the Wilkes-Barre (Pa.) Safety Station.

Jan 1, 1940

By FREDERICK H. WILLCOX

In the past the blast-furnace industry was under the stigma of being one of the most prolific sources of killed or seriously inj ured and permanently disabled workmen of any of the industries of the country. In the popular mind, labor at blast furnaces was little less hazardous than mining, powder making, or railroad work. This impression wasbased not so much on definite knowledge of the number actnally injured and the causes of injury as on the spectacular nature of the accidents that from time to time were described in the press. As with a mine disaster or a railroad wreck so with many furnace accidents, the number fatally injured in such accidents constitutes only a minor proportion of the workmen who suffer more or less serious injuries. However, the reader of the daily paper receives a distinct impression-of frightful and sudden disaster which is apt to be associated henceforth in his mind with work at blast furnaces. It is true that in the past this impression has not been without warrant, for from the time of the advent of Mesabi ores, taller furnaces, and faster smelting, which begain in the early nineties, the newspapers have chronicled a large number of blastfurnace disasters. Blast-furnace men have never assumed to tolerate failures in construction or defective control of furnaces. But the admitted hazards of the work are many, and the slow development of improvements in the construction and control of the furnace and its auxiliaries have occasionally given rise to a tendency to accept as a part of the day's work not only the unforeseen and difficultly controlled accidents but accidents whose recurrence might be stopped by the adoption of suitable preventive measures. In the smelting of iron, even more than in many other industries, safety is inseparably related to efficiency in production, and. the accidents strictly incident to work about the furnace are proportional in some degree to the success with which obstacles to smooth working are overcome. This relation does not hold, however, in regard .to such accidents as are incident to hand labor, falls, falling and flying objects, machinery, and the use of hand tools.

Jan 1, 1917

By S. S. Venkata

This volume describes a comprehensive program of research into the reliability of mine electrical power system components and the resultant reliability of the total system. The research effort encompassed analytical models, laboratory testing and field testing. The analytical work included definition of terms, fail rate functions and distributions, failure rate estimation and techniques and procedures for theoretical reliability assessment. One of the primary mine power system components addressed in the study was the ac molded case circuit breaker. This device is known to have low reliability and hence an unfavorable impact on mine safety and productivity. Ac molded case circuit breaker reliability was studied by analytical means, laboratory testing and field monitoring. A similar three-pronged' effort was made to study the reliability of undervoltage relays/releases. Particular emphasis was placed on new solid state undervoltage relays. The reliability of bulk power components, such as trailing cab les, motors, control gear, and other equipment, was assessed by gathering maintenance records from active mines. These data were compared to similar records from other industries. The work was extended to include the reliability, availability, maintainability and safety of these components.

Jan 1, 1979

By Albert L. Toenges

Early in 1944 the Chilean Government expressed a desire for assistance from the Bureau of Mines in a study of the coal deposits, coal-mining methods, and preparation and benefication of coals in Chile. A Memorandum of Understanding setting forth the purpose of the work was executed by the United States Government and the Government of Chile. Parts of this agreement are quoted: On February 4, 1944, the Ambassador of Chile in Washington expressed the interest of his Government in obtaining the loan of a mission of experts to assist in the conduct of a survey looking toward the utilization of the low-grade coals of Chile and the application of such technology as may be developed for the distillation of these coals and the use of oil shales. The matter has since been the subject of correspondence between the Secretary of State and the United States Department of the Interior, and the latter Department has agreed to cooperate with the Government of Chile, through the Bureau of Mines, subject to the following understanding:

Jan 1, 1948

By L. C. IlsLey, M. W. Von Bernewitz

"Introduction.Several hundred thousand open lights are daily carried in coal mines of the United States, each lamp being a menace to life and property through fire or explosion. They have been responsible for many disasters in the past, and will be again. Flame safety lamps have been available for over a hundred years, but during the last ten years safe and practical electric lamps have been perfected. These have eliminated many of the flame safety lamps, and in a few mines have replaced open flame lamps. But there are still more than twice as many open lamps as electric lamps in our mines, and the open lamps should be discarded in favor of an approved type of electric lamp. There are several electric miners' lamps which have been approved by the Bureau of Mines for safety and efficiency, give good light, and are easily maintained and carried, some flame safety lamps will always be used, hut mostly for detecting gas; although they might be supplanted if some simple, reliable, and cheap gas detector were developed.Explosion Hazards from Open Lights.An open light and gas*** constitute a vicious hazard; while if there be coal dust present in the vicinity the consequences are multiplied many times. An open light and black blasting powder also constitute an explosion hazard, vividly attested by several serious disasters."

Jan 1, 1924

By T. H. Miller

An attempt has been mace in this publication to present annotated references to all articles pertaining, to ore dressing that were published during 1931 and 1932; in a few instances reference is made to articles published prior to 1931 where the articles have not been included in previous bibliography appended to the annual statistical discussions of ore concentration published by the Bureau of Mines. Articles have been taken from more than 75 periodicals, journals, serials, etc., and 423 articles are abstracted herewith. A number of these abstracts, particularly those appearing in foreign publications, have been taken from Chemical Abstracts (published by the American Chemical Society, Easton, Pa.), the general use of which the authors wish to acknowledge. Other annotations were taken directly from the original publications. The entire field of ore dressing has been included in the bibliography and articles dealing with crushing, grinding classification, concentration, thickening, and filtration have been included, as well as on amalgamation, cyanidation, leaching, magnetic concentration, washing, etc., and on theory and laboratory operation. The articles are arranged in alphabetical order by authors. Lack of printing funds prohibited the inclusion of a subject index.

Jan 1, 1934

By F. M. Boler

The U.S. Bureau of Mines conducts research at the Galena Mine, Wallace, ID, with the aim of mitigating the effects of rock bursting. Destress blasting is commonly used as a stress control technique at the mine. A digital seismic array and an array of borehole pressure cells (BPC's) had been installed near the site of a stope undergoing mining and periodic de stressing. The instrumentation was being monitored at the time of a destress blast of the 46-99 stope. No significant seismic events occurred coincident with the destress. However, the destress was followed by a 2 ½ -week period of increased seismic activity, including two damaging events on February 7, 1990, at 034500 (hour, minute, and second) and 122020 Pacific standard time. BPC measurements indicated coseismic ground pressure changes on the order of 200 to 300 kPa associated with the damaging events. Fault plane solutions and dislocation models established that stress changes induced by the event at 034500 may have been significant in promoting the occurrence of the event at 122020. Theoretical investigations suggest that applying knowledge of the existing stress field, an understanding of rock burst mechanics, and fracture mechanics principles can improve destress effectiveness.

Jan 1, 2010

By Charles Will Wright

The purpose of this paper is to present briefly certain preliminary results of the study of mining methods by the United States Bureau of Mines; to show the relative importance of each method in terms of tonnages mined and man-hours consumed; to give to the mining engineers and particularly to the young student of mining a better understanding of the principal mining methods; and to indicate changes now in progress and to present suggestions for improvements in the art of mining. Questions of mine development and details of underground practice such as drilling and blasting, loading, hauling, hoisting, ventilating, pay systems and mine management are omitted, as these have been or will be discussed in other bureau publications.

Jan 1, 1931

The lignite deposits of the United States represent a huge potential source of fuel for power generation. It has been estimated that lignite constitutes about 24 percent of the remaining National reserves of solid fuel on a tonnage basis and about 15 percent of the reserves on a B.t.u. basis. (See sec. 3, part 1.) The major portion of these reserves is in North Dakota. Lignite has been used locally for domestic heating since the first settlers burned it at forts and fur-trading posts as early as 1855. Some of the first studies of the use of lignite in steam boilers were conducted by the Federal Bureau of Mines from 1910 to 1920 (15, 19) 1/ However, the commercial utilization of lignite as fuel for producing power developed slowly. Not until about 1925 was any really successful lignite industrial fuel-blaming equipment developed. Since then the commercial use of lignite as a fuel for producing power has been increasing steadily.

Jan 1, 1954

By Allen L. Frank

The uranium mine environment is characterized by airborne radon-222 and its daughter products to which miners are exposed through breathing and by gamma and X rays from the uranium-235 and uranium 238 chains to which the miners are exposed externally. The nature of the radon-daughter concentrations and the methods used to define and measure the exposures are explained through an extensive review of the literature. An improved passive track-etch dosimeter for personal use is proposed which has a measurement range of about 30-400 WLH with a 95% confidence interval to ~25% for individual detector measurements in relatively stable mine air. Some measurements of these dosimeters adapted to environmental use are also presented. A program of development for enhancement of dosimeter sensitivity and greater accuracy of measurement is outlined. Extensive gamma-ray survey measurements were made in two Colorado and three New Mexico mines. Follow-up personal miner dosimetry with LiF TLDs was done at the mine with the highest exposure rates, The average miner exposure rate measured was 4.27 mR per day, or 9.3 of the maximum permissible level averaged over 13 weeks. Comparisons are made with previous mine surveys and their value in estimating miner exposure is discussed. Some depth-dose measurements made using Lucite as the absorber are evaluated.

Jan 1, 1978

By P. M. Daling

The objectives of this study were to examine a representative cross section of formal safety analysis techniques developed for the nuclear and aerospace industries, to recommend those methods that would be suitable for application to the mining industry, and to include those methods in a user's manual. Volume II of this report, the user's manual, describes several methods that were determined to be immediately transferrable to the mining industry. The handbook gives detailed instructions on appropriate application and utilization of the methods. Other techniques will require further development before they can be effectively transferred to the mining industry.

Jan 1, 2006

By Michael Radnor

The purpose of the study was to 1) examine the social and economic impacts of surface mine blasting in relation to variations in conditions of terrain and geology, population density and type, levels of ground motion and air blast; 2) consider technical, legal and government policy issues; and 3) examine the potential, nature and extent of surface mine blasting impacts and its regulations upon both communities and surface mining companies. Phase One designed the empirical research and technical analyses of Phase Two, focused upon surface coal mining and quarrying in the Eastern U.S. Several broad conclusions are evident: 1) blasting is not the major issue for communities or surface mine companies; 2) while the number of instances of severe cracking or annoyance are relatively small, the impact can be severe for individuals immediately involved; 3) blasting/drilling cost curves tend to rise significantly at intervals below 1.0 particle velocity, in/sec, dependent upon the size of a permit area and the size of a mine; and 4) the legal, complaint, cost and density analyses do not suggest the need for a general lowering of present regulations.

Jan 1, 1981

By J. J. de Barbadillo

This report describes a process for recovering chromium and other metals from superalloy scrap. Part I contains the results of laboratory scale experiments which were conducted to test a complex flowsheet utilizing a wide range of extractive metallurgical operations. The novel basis for the process is the formation of a sulfide matte in which chromium is concentrated in a discrete chromium sulfide phase. Mineral processing and hydrometallugical procedures are used to separate chromium sulfide from the other matte constituents. The products of the process are a chromium-nickel alloy suitable for reuse in the superalloy industry, electrolytic nickel, electrolytic cobalt, and an iron-molybdenum residue. Recovery of the principal elements contained in the scrap are chromium(Cr)-93 percent, nickel(Ni)-99 percent, cobalt(Co)-96 percent, molybdenum(Mo)-92 percent. Part II encompasses a preliminary engineering design of a pilot plant capable of treating 100 pounds(lb) of superalloy scrap per hour. Also included is an economic analysis of the operation of the pilot plant.

Jan 1, 1980

By R. A. V. Raff

Although falls of roof, face and rib (or side) of coal mines were the third ranking cause of disabling accidents in 1966, the accidents from these falls resulted in the most serious injuries and accounted for approximately 50 percent of the total fatalities (I). Further breakdown of these statistics shows that 88 percent of the fatal accidents occurred within 100 feet of the working face and that 96 percent of the deaths were in bituminous mines, with only four percent taking place in anthracite workings. These figures demonstrated the need for improved reinforcement procedures in operational coal mines, and they provided ample justification for research in the area of accident prevention. The purpose of this project was to investigate the use of polymers and of related techniques to achieve rock bonding and reinforcement of coal mine structures, in order to obtain better or permanent ground support (e.g., drifts, entrees, coal and ore passes, galleries, tunnels and shafts) by the fill ing of fissures in the rock, thereby preventing or delaying the onset of serious rock degradation processes.

Jan 1, 1973

By T. W. Quayle

This paper describing mining practices at the United Verde copper mine, Jerome, Ariz., is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts f the United States. At present mining operations are being conducted both underground and by electric shovels in an open pit. The open-pit work has been described by E. M. J. Alenius in a previous publication of the Bureau of Minos;3 the present paper will be confined to a description of the underground mine. The underground methods comprise horizontal cut-and-fill, shrinkage with delayed filling, horizontal square-set, inclined square-set, and top slice. The normal daily production of the underground mine is 3,000 tons of copper ore per day, requiring the employment of 900 men underground.

Jan 1, 1931

By C. P. Haller, S. J. Aresco

"INTRODUCTION The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heat¬ing value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the fusing temperature of ash and the free-swelling index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions./ issued by the Bureau; the samples are analyzed in the Bureau's laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made.Analyses of the delivered coal and ""tipple"" samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. Moreover, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.The Government purchased approximately 5-1/2 million tons of coal in fiscal year 1951. In connection with these purchases, the Bureau analyzed 10,700 samples. These are published for the use of Government officials and the public. A series of publications s been completed on coal analyses by States, or, where production is small in any State, by groups of adjacent States. In addition to analytical data showing composition and quality of coals of the States, the publications contain brief descriptions of the geological structure of the coal basins, typical mining conditions in the various districts, the principal economic data of the industry, and the relationship of mine or channel samples to delivered and tipple samples. The present publication covers many States but deals only with the analytical data of the coals.The technical papers published by States, with their numbers are: Alabama, 347; Alaska, 682; Arizona, California, Idaho, Nevada, and Oregon, 696; Arkansas, 416; Colorado, 574; Illinois, 641; Indiana, 417; Iowa, 269 and 706; Kansas, 455; Kentucky, 308 and 652; Maryland, 465; Michigan, North Dakota, South Dakota, and Texas, 700; Missouri, 366; Montana, 529; New Mexico, 569; Ohio, 344 (and Bulletin 499); Oklahoma, 411; Pennsylvania Bituminous, 590 (Supplement, 645); Pennsylvania Anthracitic, 659; Tennessee, 356 and 671; Utah, 345; Virginia, 365 and 656; Washington, 491 (Supple¬ment, 618); West Virginia, 405 and 626; and Wyoming, 484."

Feb 1, 1953

By K. K. Kelley

This work is both a revision and an elaboration of Bureau of Mines Bulletin 371, which was published in 1934 and included data available to October 1933. During the intervening years, a large number of new experimental, high-temperature, heat-content data have become available through continuous, systematic efforts of the Pacific Experiment Station of the Bureau of Mines and the Laboratory for Inorganic and Physical Chemistry of the University of Groningen (Netherlands), coupled with various individual investigations at many institutions. In addition, calculations from spectroscopic and molecular constant data have been extended and applied to a wide variety of gaseous substances. This bulletin purposes to collect and correlate all available high-temperature heat-content and specific-heat data for inorganic sub-stances and to formulate tables and algebraic expressions for their representation. It is hoped in this manner to remove some of the tedium of thermodynamic calculations for industrial metallurgical research workers and engineers who often have available only an inadequate library in this field. It is expected also that this bulletin will have value to those teaching courses in metallurgical and chemical thermodynamics.

Jan 1, 1949

By Rita D. Sylvester

THE BUREAU OF MINES was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve mineral resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting these industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to "disseminate information concerning these subjects 'in such manner as will best carry out the purposes of this Act.'" In accordance with that directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-Bureau sources. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue describes Bureau reports and articles published during the period January 1, 1960 to December 31, 1964. It, supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960,2 and the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960.3 It supersedes the annual lists of Bureau publications and articles from January 1 to December 31, 1960,4 from January 1 to December 31, 1961,5 from January 1 to December 31, 1962,6 and from January 1 to December 31, 1963.7 The leading general and technical libraries of the United States maintain files of the Bureau's publications. A list of these libraries appears immediately following this introduction.

Jan 1, 2007

By Frank B. Fulkerson

Three of the five primary aluminum producers in the Pacific Northwest have facilities in the region to make aluminum mill products. Only one of the three, however, produces a variety of shapes and forms. The principal reason for the lag in development of an aluminum mill products industry was found to be transportation cost. The long range outlook is for expansion, based mainly on growth of the western market for aluminum used in construction, containers and packaging, electrical applications, diesel trucks, mobile homes, and irregation pipe. Consumption of western aluminum mill products in 1985 is projected at 1.1 million tons, compared with estimated consumption of 250,000 tons in 1961.

Jan 1, 1965