Search Documents

By D. R. Tesarik

To ensure the stability ofa tailings pond embankment, the height of the phreatic surface must be kept at or below a safe level. In this investigation, the Bureau of Mines analyzed various horizontal drain designs for tailings embankments to determine their effects on location of the phreatic surface. This report describes the investigation, and it includes 21 dimensionless graphs that can be used to estimate the drain spacing and length dimensions necessary to ensure the stability of embankments of various configurations. Analyses were based on the use of two computer codes, a three-dimensional finite-element code and a two-dimensional finite-difference code. The computer-generated results were compared with results obtained from a laboratory embankment model, other laboratory test results, and piezomet-ric data from two actual tailings embankments. Nearly the same phreatic surface locations were predicted using either of the computer codes. For one of the actual embankments studied, the predicted phreatic surface location was slightly higher than the measured location; for the other, the predicted location closely followed the actual surface trend. Phreatic surfaces of the laboratory model were slightly higher than the code-gener-ated locations, and the differences grew larger as drain length increased or drain spacing decreased.

Jan 1, 1984

By Frank E. Cash

Although during the past 10 years Alabama has attained an enviable position by its coal-mine accident experience and, like most of the other coal-mining States, has made progress in the safer operation of coal mines, there is still room for improvement, which can be realized only by still greater efforts on the part of employees and employers. From 1993, when accidents were first recorded by the Alabama State Mine Inspection Department, to 1934, inclusive, 3,451 men lost their lives in the production of 569,722,676 tons of coal. The primary purpose of this report is to bring to the attention of the mining industry in Alabama end elsewhere statistics of fatal accidents for 1931-34, with the hope that a study of the causes may lead to reduction of similar accidents in the future.

Jan 1, 1936

By Stephen A. Hare, O&apos

Powder metallurgy processing of commercial Raney nickel powders was examined. The typical angular particle shape, in conjuction with aluminum present in a eutectic phase, facilitated interlocking leading to excellent green strength after compaction. Density and porosity as influenced by the compacting pressure were studied over the range of 37.5 to 207 meganewton per square meter (MN/m2). Sintering in an inert atmosphere from 575° to 850° C caused a volume increase which is attributed to a solid state reaction between Al and Ni2Al3 phases. The reaction is 3Al + Ni2Al3 ? 2NiA13. A thermal pretreatment of 70 hours at 700° C was required to prevent this reaction from occurring during sintering. Density and porosity as a function of compacting pressure and sintering temperature were determined after a thermal pretreatment of the powder.

Jan 1, 1976

By Wiliam L. Crentz

The importance of Somerset County, Pa., as a coal producer is due in large measure to the presence reserves of low-volatile bituminous coals. Although many coal beds of minable thickness are present, the important reserves are to be found in those beds underlying the Pittsburgh bed. The Kittenning beds and Freeport beds, which are responsible for the bulk of the present coal production in Somerset County and contain the largest reserves to meet future coal requirements, are usually thin and entirely free from impurities. The Pittsburgh bed, which has been such an important coal deposit in the coal areas immediately west and south of Somerset County, is of secondary importance in this county. Although generally rather friable, Somerset County coals have enjoyed wide receptability as excellent coals and to some extent have been utilized in the metallurgical market.

Jan 1, 1951

By Doerner H. A.

From thermodynamic calculations Maier predicted that zinc oxide and methane would react at specified temperatures substantially according to equation (1). (1.) ZnO + CH4 = Zn (gas) + CO + 2H2. Other reactions that may take place are (2.) CH4 = C + 2H2. (3.) ZnO + CO = Zn (gas) + CO2. (4.) ZnO + H2 = Zn (gas) + H2O. Maier predicted that 870°C would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1), at equilibrium, would be substantially complete at or above 927°C. Theoretical considerations indicate that reaction (1) is reversible: this is supported, but not proved, by experimental data. The other reactions are known to be reversible. At low temperatures reaction (2) requires a catalyst and it is slow below 1000°C. Reactions (3) and (4) are rapid, but the equilibrium constants are such that only small concentrations of CO2 or H2O can be produced below 1000°C. Maier calculated that CO2 should not exceed 0.5 per cent at 870°C., and the calculation for water vapor gives a still smaller order of magnitude.

Jan 1, 1931

By H. A. Doerner

From thermodynamic calculations3 Maier predicted that zinc oxide Land methane would react at specified temperatures substantially according to equation (1). (1) ZnO + CH; = Zn (gas) + CO + 2H2 Other reactions that may take place are: (2) CH4 = C + 2H2. (3) ZnO + CO = Zn (gas) + CO2 (4) ZnO + H 2 = Zn (gas) + H2O . Maier predicted that 870°C. would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1), at equilibrium, would be substantially complete at or above 927°C.

Jan 1, 1931

These proceedings consist of papers presented at Bureau of Mines Technology Transfer Seminars in December 1983 for the purpose of disseminating recent advances in mining technology in the area of mine ground control. The Bureau of Mines conducts several of these seminars each year in order to bring the latest results of Bureau research to the attention of the mining industry as quickly as possible.

Jan 1, 1984

By R. C. Buehl

Pilot-plant tests have been in progress at the Bureau of Mines, Pittsburgh, Pa., on the recovery of manganese from open-hearth slag.3/4/5/ In the process, 1 the slag is first reduced in a blast furnace to make a high-phosphorus spiegeleisen containing 12 to 22 percent manganese. A slag containing 55 to 60 percent manganese is made from this spiegel by oxidation in a basic-lined converter. The metal from this blowing operation contains about 3 percent phosphorus, 1 percent manganese, and less than 1 percent carbon. Economic efficiency in the manganese-recovery process requires that this metal be converted into steel. Because of its high phosphorus content the metal is suitable for blowing in a basic-lined converter. In most of the tests described in this report, metal of this composition was used as the starting material in a 1-ton, side-blown, basic-lined converter. Although basic-lined converters are not used for steel production in the United states, in Europe a considerable portion of the steel is made in them. Open hearths largely have replaced converters for steelmaking in the United States; mainly because open-hearth steels have better physical properties than converter steels because of lower nitrogen and phosphorus contents. However, by improving converter design and operating technique during the past 15 years, metallurgists have found that low-nitrogen steels with physical properties equal to open-hearth steels can be produced in converters.6/ Tests at Jones & Laughlin steel Corp. with side-blown, acid-lined converters of 3 and 22 tons capacity showed that steel with a low nitrogen content comparable to that of open hearths operating on scrap charges could be made by surface blowing.7/

Jan 1, 1955

By B. R. Mohal, F. F. Aplan, S. Chander

"The wetting behavior of coal has been determined in the presence of nonyl and octyl series of nonionic surfactants containing polyethoxy groups of different sizes. The wetting behavior was determined by a modified Walker technique and contact angle measurements. The results show that the wetting rate of coal varies with coal rank, structure of the hydrocarbon chain and number of ethoxy groups in the hydrophilic group of the surfactant. A close relationship has been observed between the wetting rates and the short-time advancing contact angles.INTRODUCTIONNonionic surfactants are used in many applications to improve wettability of solids. They can be used as dispersing agents [ 1 ] or dust suppressants [ 2-5] and to control the flotation, flocculation, filtration and, flowability of particulates. This study was undertaken to study the effect of a series of nonionic surfactants on the wetting behavior of coal. Two series of surfactants, namely, ethoxylated nonyl and octyl phenols were used. The nonyl phenol series con tains a linear hydrocarbon chain containing nine carbon atoms (CH3 ( CH2 )8-C6H4- ( OC2H4 ) n, where n is the number of ethoxy groups) . The octyl phenol series contains a branched hydrocarbon chain containing eight' carbon atoms ( ( CH3 ) 3CCH2C ( CH3) 2-C6H4- ( OC2H4 ) n ).Initial wetting rates — modified Walker techniqueWalker et al. [ 6 ] developed a sink test to determine the wettability of coal particles. In this technique, coal particles are dropped individually onto the surface of surfactant solutions of different concentrations, and the most dilute concentration in which coal would sink ""instantaneously"" is determine& This technique is a variation of a procedure initially developed by Draves and Clarkson [ 7 ] to determine the effect of surfactants on wettability of cotton fibers."

Jan 1, 1989

By K. K. Kelley

Sodium-aluminum and potassium-aluminum silicates are among the more important rock-forming minerals of the earth's crust. They also appear as constituents of some metallurgical slags and of some refractory materials. Consequently, knowledge of their thermodynamic properties is interesting and valuable from several viewpoints. This paper reports experimental determinations of the low-temperature heat capacities and entropies at 298.16° K. of albite, jadeite, and nephelite it the sodium-aluminum silicate series and of adularia, ferriferous orthoclase, leucite and kaliophilite in the potassium-aluminum silicate series. Also high-temperature heat-content and entropy increments about 298.16° K. are reported for albite, jadeite, nephelite, and carnegieite in the sodium-aluminum silicate series. Except for a few high-temperature heat-content values for albite, all these data are available for the first time.

Jan 1, 1953

By R. Lindsay Mundell

In the first half of 1990, lessening of cold war tensions was welcome. But Iraq's invasion of Kuwait in August led to the Persian Gulf War in January and February 1991. The subsequent oil shock contributed to a dampening of the U.S. economy, and the U.S. gross national product rose only 0.9 % to $5,463 billion (U.S. billion = 109). The buildup of military forces in the Persian Gulf area focused greater attention not only on petroleum but also on other strategic materials. The U.S. Department of Defense continued to review stockpile goals and upgrade several mineral materials. In addition, the U.S. Bureau of Mines continued to maintain the standby Emergency Minerals Administration. After the Defense Production Act, which authorizes priorities, allocations, and supply expansion, lapsed on October 20, 1990, the Selective Service Act of 1967 became the authority to ensure that orders of the Armed Forces and defense atomic energy programs were given priority treatment.

Jan 1, 1993

By H. F. Yancey

A relatively large proportion of the coal produced in the state or Washington, especially in the coking coal areas is of fine size; hence washing by means of coal-washing tables to reduce the ash content is commonly practiced. For this reason the program of research in coal washing conducted jointly by the U. S. Bureau of mines and the College of Mines, University of Washington, has given special attention to the mechanism of the separation of coal from its impurities as affected by the coal-washing table with the object of

Jan 1, 1931

By J. D. Ramsdell

The object of this investigation by the Federal Bureau of Mines was to evaluate the workability, recrystallization characteristics, and mechanical and physical properties of high-purity electrorefined vanadium. The low level of interstitially soluble elements in electrorefined vanadium results in a soft ductile metal which responds readily to cold working by rolling, swaging, and press-forging. Hardness, strength, and resistivity increased with an increase in impurity content, but thermal expansion was independent of impurity content. The work-hardening of vanadium occurs rapidly. Most of the hardness increase occurs in the first 15 pct. of reduction in area. When vanadium is annealed, its hardness increases to a maximum when the annealing temperature is between 200° to 400° C. A sharp decrease in hardness develops as the annealing temperature is increased. An anomaly in the hardness versus annealing temperature curve is present in the 600° to 800° C. range, while all evidence of cold-work is removed at annealing temperatures above 900° C.

Jan 1, 1961

By H. F. Yancey

A relatively large proportion of the coal produced 1n the State of Washington, especially in the coking coal areas is of fine size; hence washing by means or coal-washing tables to reduce the ash content is commonly practiced. For this reason the program of research in coal washing conducted jointly by the U. S. Bureau of Mines and the College of Mines, University of Washington, has given special attention to the mechanism or the separation of coal from its impurities as effected by the coal-washing table with the object of increasing its efficiency. Previous work has evaluated the role of stratification the influence of size, specific gravity and respective shapes of particles in the feed, and the affect of hindered-settling classification of the feed prior to tabling.

Jan 1, 1931

By Jay F. Colinet

Longwall mining in lower seam heights may necessitate the use of single-drum shearers to overcome size constraints associated with standard double-drum shearers. To avoid the operational problem of clearance in the tailgate entry with one single-drum shearer, two single-drum machines can be operated on the same face, with each shearer responsible for mining a predefined portion of the face. However, utilization of two shearers on the same face necessitates the positioning of one shearer operator and a jacksetter in the return air of the upwind shearer, thus complicating respirable dust control on the longwall. In an effort to evaluate the unique dust control problems associated with this type of mining, the U.S. Bureau of Mines conducted dust surveys on two multiple-machine longwall operations. Sampling was done to quantify major sources of respirable dust and to identify potential solutions to problem areas. Sampling results indicate that the cutting sequences utilized on multiple-machine faces may have to be designed to minimize dust exposure, as opposed to optimizing productivity or facilitating operational requirements. Also, state-of-the-art dust control techniques typically found on double-drum shearer longwalls must be employed to help minimize the exposure of all face personnel to traditional dust sources.

Jan 1, 2010

By R. E. Mussier

This investigation was made to study new methods to prepare high-purity yttrium metal, Various methods were used to prepare pure intermediate compounds, primarily chlorides, bromides, and iodides, which were subsequently reduced to metal. The process found most suitable for the preparation of pure anhydrous yttrium chloride involved thermal dehydration of a mixture of hydrated yttrium chloride and ammonium chloride while under vacuum. Yttrium bromide and iodide were prepared most effectively by the direct halogenation of yttrim carbide. Yttrim carbide was obtained by reacting and melting yttrium oxide-carbon mixtures in a carbon-arc furnace. Yttrium halides were purified by vacuum distillation and reduced by alkali or alkaline-earth metals. Lithium and sodium proved to be the best reductants from the standpoint of yield (>95 pct) and purity (>99.8 pct) of the yttrium. The product of the reduction step was sponge metal, which was consolidated readily by conventional cold-mold, arc-melting procedure. The purest yttrium obtained in laboratory scale work was prepared by sodium reduction of yttrium chloride and contained only 125 pp oxygen; other impurities did not exceed 1,000 ppm. In larger scale tests yttrium containing only 800 to 1,000 ppm total impurities was obtained by lithium reduction of yttrium chloride. The tensile properties of high-purity yttrium were determined. Mechanical tests showed that yttrium can be forged, extruded, rolled, spot welded, and deep drawn.

Jan 1, 1963

By Arnold B. Hubbard

Automatic control instruments were utilized by the Bureau of Mines for routine assays of large numbers of oil shale samples and other bituminous materials. The standard Fischer assay method was automated by automatically controlling the heating cycles of a battery of 12 electric heaters with electronic controllers and programmers. The condensers were cooled with a modified automatically controlled refrigeration bath. The complete assembly consisted of 12 retort units, necessary control instruments, and the refrigeration bath. This equipment was capable of producing more consistent results than those previously obtained with the gas-heated retorts and of increasing the output of assays substantially with no increase in operating personnel.

Jan 1, 1965

By Robert E. Manning

The Federal Coal Mine Health and Safety Act of 1969 has placed stringent limitations on the noise levels in which employees may work. This act can result in both increased labor costs because of noise-exposure time limitations and in high capital costs for modification of present equipment, and the design of new equipment, to comply with the law. The development of new noise-control systems is thus of immediate interest to industry. A current Research program at U. S. Steel is aimed at developing methods of controlling both the exhaust-air noise and the mechanical noise of a Stoper drill, a pneumatic percussive tool used for roof-bolting purposes in coal mines which has an approximate air consumption of 100 cubic feet per minute. This program is being performed under a contract between USS Engineers and Consultants, Inc. and the Pittsburgh Mining and Safety Research Center of the U. S. Bureau of Mines. In previous work at U. S. Steel, kidney-shaped mufflers were designed that wrap around the air leg of the drill for control of the exhaust noise. These mufflers were designed with the aid of a digital computer program that predicts the acoustic performance of mufflers.

Jan 1, 1975

By W. K. Tolley

The Bureau of Mines is testing super critical fluids as solvents to selectively extract valuable components from complex matrices. Materials recovered during supercritical fluid extraction are often highly purified. Using laboratory apparatus designed specifically for supercritical fluid research, Bureau re-searchers have measured the solubility of titanium tetrachloride (TiCI4) in supercritical, liquid, and gaseous carbon dioxide (C02), CO2, a commonly used supercritical fluid, is inert, inexpensive, and nontoxic. Supercritical CO2 formed a single phase with TiCl4 at 45° C and 1,500 psig. When the solution was heated at constant pressure beyond 55° C, TiCl4 precipitated from the fluid. Results showed that TiCl4 solubility in supercritical CO2 is not controlled by the vapor pressure of the solute.

Jan 1, 1989

Objective: To provide a safe, practical, cost-effective method for measuring coal rib thickness during highwall mining.

Jul 1, 2008