Search Documents

By G. W. Jones

The operation of combustion engines of various types at high altitudes and other combustion processes at reduced pressures have made it desirable to determine limits of flammabilities -under these conditions. Experiments carried out by the Bureau of Mines have shown that although natural gas-air mixtures become more difficult to ignite as the pressure is reduced below atmospheric, with a suitable source of ignition the limits of flammability are as wide at 175 mm mercury absolute as they are at atmospheric pressure.

Jan 1, 1949

By G. W. Birge

Carbonizing properties of the principal coalbeds of Elk, Clarion, Jefferson, Clearfield, and Centre Counties, Pa,, are described in this Bureau of Mines report, Twenty-six samples, representing the Upper Freeport, Lower Freeport, Upper Kittanning, Middle Kittanning, Lower Kittanning, and Brookville beds, were carbonized by the Bureau of Mines--American Gas Association (BM-AM) method, and yields of products and physical properties of cokes were determined. Expansion or contraction of the majority of the samples was measured in the Bureau of Mines sole-heated oven. Chemical analyses, agglutinating values, and free-swelling indexes are given for all samples. In this area the coals generally are characterized by high sulfur and moderately high ash content, and their suitability for metallurgical use would depend largely upon satisfactory cleaning. The samples from Elk, Clarion, and Jefferson Counties were high-volatile A bituminous In rank, whereas, most samples from Clearfield County and all those from Centre County were of medium-volatile rank. Coals from Clarion County had dry, mineral- matter-free fixed-carbon contents ranging from 56.5 to 60.3 percent and were weakly coking. With the exception of two samples which contained excessive ash, the medium-volatile coals of Clearfield and Centre Counties were strongly coking and, as indicated by sole-oven expansion results, would require blending with lower rank coal to avoid oven damage.

Jan 1, 1963

By C. R. Nisewanger, F. W. Brown

"The velocity of detonation of an explosive is one of its most important properties, because its performance depends markedly on the rate at which it releases its energy. Fortunately, the velocity of detonation is one of the few properties of an explosive that can be measured precisely. However, the velocity of detonation of an explosive may depend on several factors other than its chemical composition, such as density, physical state, degree of confinement, nature of confinement, and magnitude of initiating impulse. Presumably for an explosive of fixed chemical and physical properties there are certain limiting conditions of confinement and initiation under which the explosive will detonate at a maximum constant and uniform velocity. This velocity is its ""ideal"" velocity of detonation. It is obvious, however, that in order to evaluate performance properties of an explosive in all of its applications it may be necessary to measure its velocity of detonation under a number of conditions in which the velocity of detonation is far from the maximum ""ideal"" velocity.. Under certain-conditions the velocity of detonation may even,be,different at different points in the explosive.It is .relatively simple to determine the velocity of detonation of an explosive under a. standard set of conditions if one is free to use large quantities of the explosive and to form it into a convenient shape. Under these circumstances; one can use a thin column of explosive a meter or more in length. The time required for an explosion to travel the length of the column will not be less,of the order a few ten-thousandths of a second and can be readily and accurately measured .by means of the standard spark chronograph or by photographing the explosion with a rotating-drum camera. However in many applications the explosive charge may be of relatively small dimensions arid may not be in a form convenient for making velocity measurements and often may be enclosed in a case or other confining medium. It may be necessary to determine the velocity of detonation over distances of the order of a few centimeters, in which case the time intervals to be measured will be extremely small. For example, the time required for an explosion to traverse 1 centimeter of tetryl is of the order of 1.5 microseconds.Since no satisfactory method of determining time intervals of the order of magnitude of a few microseconds within an explosive charge was available,, at least not for all conditions that might be encountered in practice, it was necessary to develop a special electronic chronoscope which is capable of measuring time intervals as small as a microsecond with a fair degree of accuracy. This report describes the chronoscope and its application to measurements of velocities of detonation in explosives."

Mar 1, 1946

By R. P. Beyer

Low-temperature heat capacities and standard enthalpy of formation of copper difluoride (CuF2) were determined by the Bureau of Mines. The low-temperature heat capacities were determined from 11 to 302 K by adiabatic calorimetry. The enthalpy of formation was determined by HC1 solution calorimetry. The standard values of entropy (S°) and enthalpy of formation (?Hf°) at 298.15 K are l8.65±0.03 cal/deg mole and -129.02±0.29 kcal/mole, respectively.

Jan 1, 1978

By V. P. Bhavanandan

The mucus secreted in the respiratory tract provides the first barrier against inhaled particulate and gaseous toxicants. Trachea removed from pathogen-free rats were maintained as organ cultures and used to study the effects of coal dust exposure on the synthesis of mucin. The high molecular weight isotopically labeled (3H-glucosamine, 14Cleucine or 35S-sulfate) mucin could be purified by gel filtration, treatment with testicular hyaluronidase, ion exchange chromatography, delipidation and CsBr density gradient centrifugation. To examine effect of coal dust on mucin production, groups of explant cultures were exposed to media containing coal dust at 100 µg per ml every 2 days for 2 weeks while control cultures were treated with media without dust. Analysis of the spent culture media showed that treatment with dust markedly decreased the production of nondialysable glycoproteins as well as hyaluronidase-resistant acid-precipitable fraction consisting mainly of mucin. Since the synthesis of protein was not affected to the same extent the decrease in mucin production is not entirely due to cell death. In separate experiments rats were subjected to in vivo coal dust exposure in inhalation chambers and tracheae of these and control rats were removed for explant cultures. The incorporation of precursor isotopes into mucin by these explant cultures are being examined. (Supported by U.S. Bureau of Mines through the Generic Mineral Technology Center for Respirable Dust under grant G1135142, project 4210).

Jan 1, 1988

By E. B. Kester

In the commercial evaluation of coal tars, a distillation analysis properly carried out is of considerable importance. Close attention must be given to this operation in order to obtain consistent results and to secure the minimum decomposition of the tar compounds, Which in Many cases are sensitive to undue heat effects. Low-temperature tars in particular contain compounds of this nature, while in the case of tars produced at high temperatures the large proportion of pitch present has an adverse influence during a distillation. If excessive cracking takes place, the composition of the distillate will naturally vary from the normal, with the result that all the analytical criteria subsequently obtained are affected. Where tars, produced over wide ranges of carbonization temperatures are investigated as in the survey of gas, coke, and by-product making properties of American coals now being conducted at the United States Bureau of Mines Pittsburgh Experiment Station, the method of distillation must necessarily be the same for all of the tars studied. Also, it mast function equally well for both low and high temperature tar permit accurate fractionation, and reduce adventitious decomposition to a minimum. The authors are aware that certain types of distillation analysis which do not meet the above requirements may give results comparable with those of the large stills of a by-product coke-plant where one type of tar is produced. These may be simpler and shorter and entirely suitable for control work, but at the same time have little value in a fundamental investigation.

Jan 1, 1932

This report describes magnetic field measurements in the Helvetia Coal Co. Lucene #8 Mine for purposes of deriving a mapping of the magnetic field strength covering the major haulageways which contain conductors. The measurements were performed by Terry S. Cory, P.E. under U.S. Bureau of Mines purchase order P0372716. Assisting in performance of the measurements were personnel from the Bureau of Mines, PMSRC, and Helvetia Coal Co. Acknowledgement is given to Engineer Tom Strong of Helvetia Coal Co. who accompanied the measurement team and who lended support in performing the measurements and in supplying valuable engineering information for use in evaluation of the results. The results of the testing at medium frequency show that coverage of the entire mine area containing conductors can be achieved employing wireless radio techniques whereby radio signals are coupled into and are carried by these conductors. These results confirm earlier qualitative testing of the Collins Mine Wireless Radios in this mine. These results, performed over the frequency range 71-2890 KHz, illustrate the effect of frequency on the radio propagation with the conclusion that the best overall coverage is obtained at frequencies approximating 1000 KHz. This report presents all the raw data and the reduced data in the form of magnetic field strength contour maps. Sufficient information is provided to enable independent reduction of the data. A summary of observations which can be made directly from the contour maps is given.

Jan 9, 1977

By Robert K. Koch

The reactions of alumina and alumina monohydrate with wet hydrogen fluoride gas were studied by the Federal Bureau of Mines to determine the feasibility of producing commercial-grade aluminum fluoride from offgases generated by pyrohydrolysis of siliceous fluorspars. The test results showed than an aluminum fluoride reactor operating at maximum efficiency could retain 96 percent of the fluorine contained in off-gases generated by pyrohydrolysis of siliceous fluorspar. The requirements are a reactor temperature of 200° C. and a reactor entrance gas containing 5 mole-percent hydrogen fluoride. Partial pressure equilibrium constants were determined for the reaction of alumina monohydrate and wet hydrogen fluoride gas from 200° to 350° C. and for the reaction of alumina and wet hydrogen fluoride gas from 350° to 700° C. Both reactions are reversible, and they proceed in directions that are dependent upon the temperature and the relative HF:H2O concentration. Logarithms of the equilibrium constants were used to plot the reaction isobars; these can be used to calculate the theoretical maximum efficiency of a reactor processing wet hydrogen fluoride gas between 200° and 700° C. The theoretical maximum efficiency decreases with increasing temperature.

Jan 1, 1961

By Murray Jacobson

The respirable dust standard in the Federal Coal Mine Health and Safety Act of 1969 is designed to prevent disability and death from coal workers' pneumoconiosis. Beginning June 30, 1970, the operators of coal mines were required to maintain the average concentration of respirable dust in the active workings at or below 3.0 milligrams of dust per cubic meter of air. The standard is reduced to 2.0 milligrams per cubic meter after Dec. 30, 1972. This paper presents the equipment and procedures used by the coal mine operators in implementing the respirable dust sampling program established by the Secretary of the Interior and the Secretary of Health, Education, and Welfare and shows the effect of the law, during the first year, on the reduction of dust levels in selected mines. The system employed by the Bureau of Mines for analyzing and processing the dust samples is also presented.

Jan 1, 1971

By E. B. Kester

In the commercial evaluation of coal tars, a distillation analysis properly carried out is of considerable importance. Close attention must be given to this operation in order to obtain consistent results and to secure the minimum decomposition of the tar compounds, which in many cases are sensitive to undue heat effects. Low-temperature tars in particular contain compounds of this nature, while in the case of tars produced at high temperatures the large proportion of pitch present has an adverse influence during a distillation. If excessive cracking takes place, the composition of the distillate will naturally vary from the normal, with the result that all the analytical criteria subsequently obtained are affected. Where tars, produced over vide ranges of carbonization temperatures are investigated as in the survey of gas, coke, and by-product making properties of American coals nor being conducted at the United States Bureau of Mines Pittsburgh Experiment Station, the method of distillation must necessarily be the sane for all of the tars studied. Also, it must function equally well for both low and high temperature tar, permit accurate fractionation, and reduce adventitious decomposition to a minimum.

Jan 1, 1932

By A. T. Iannacchione, D. G. Puglio

This Bureau of Mines study covers 25 underground mines that were active in the Upper and Lower Freeport and Lower Kittanning coalbeds in 1976. The coal ranges from low to medium volatile in rank; its primary use is for steam generation. Seven mines emit more than 100,000 cfd of methane gas; those mines are the deepest and largest producers. The methane gas content of three core samples of the Lower Kittanning coalbed was estimated by the direct method. A sample from a depth of 320 feet contained 0.5 cu cm of gas per gram, at 620 feet there was 0.8 cu cm of gas per gram, and at 1,060 feet there was 11 cu cm of gas per gram. These results suggest that methane control problems will be encountered in the future as deeper coal is mined.

Jan 1, 1979

By N. Greninger

The Bureau of Mines examined the possibility of a seasonal variation of respirable dust concentration in U.S. coal mines. The first step was to review company and MSHA-inspector dust samples that had been collected during the past several years in 14 selected mines for compliance purposes. Results indicated severe scatter in data; most standard deviations of the dust concentrations measured in winter and summer months were comparable in magnitude with the mean values of dust concentrations for the seasons. Therefore, a detailed statistical analysis was conducted. At the 90% confidence level, the company samples of three mines had winter means 0.15 to 0.54 mg/m3 higher than the summer means; six mines had negligible seasonal variations; and five mines had winter means that ranged from higher to lower than the summer means. Inspector data, however, were too sparse for analysis. In view of both the low frequency of occurrence of a seasonal effect and its wide scatter in several of the mines, the study was ended with the conclusion that seasonal varia-tion in respirable dust levels, in general, is an insignificant factor.

Jan 1, 1986

By James V. Kelly

During the winter of 1946 and the spring of 1947, the Bureau of Mines conducted an investigation and drilling program in the vicinity of the village of Fairplay, Wis. Fifteen diamond drill holes totaling 2,457.6 feet of bore were completed. This work was part of a general study of the zinc-producing area of southwestern Wisconsin and had the particular purpose of investigating a structural trend, determined by the Federal Geological Survey, in an area some distance from known ore bodies or active mines.

Jan 1, 1948

By R. D. Govier

The U.S. Bureau of Mines has developed a thin-film X-ray fluorescence technique to rapidly determine Cu, Ni, Co, Fe, and Cr in super alloy leach liquors. Total analysis time per sample was less than 15 min, as opposed to several hours for traditional wet chemical methods. Precision and accuracy were checked by replicate analyses of solutions similar in composition to leach liquors, whose analyte concentrations were well known. Coefficients of variation for all elements were found to be less than 2 pet. With the exception of the results for Fe, all relative errors of estimation were also found to be less than 2 pet. Bulk liquids are not introduced into the spectrometer; thus, the potential for damage to the instrument by leakage of corrosive liquids is eliminated.

Jan 1, 1989

By C. A. Komar

The Bureau of Mines conducted experiments on one synthetic and three natural sandstone samples to investigate the effects of acoustic energy on the flow of brine in porous media. Ultrasonic energy at a frequency of 20 kc per second and an intensity of 55 watts per cm2 was irradiated in the direction of the fluid flow and in the opposite direction for distances of 1/2 and 2 inches between the vibrating device and the sample face and under conditions of suppressed and nonsuppressed cavitation. Forty tests were conducted: 32 with a pressure differential of 0.64 psi across the samples, 2 with 5 psi, and 6 with 15 psi. Acoustic waves altered the rate of flow of the brine through the samples, but this effect was observed only at low differential pressures and from a practical point of view was insignificant. As a result of irradiation, however, the samples exhibited reduced permeability. This reduction was probably caused by the shifting of solid particles dislodged by the acoustic waves.

Jan 1, 1967

By J. H. Hild

The Shanton magnetite-ilmenite deposits lie on the east flank of the Laramie Mountains, 43 miles northeast of Laramie, Albany County, Wyo. (fig. 1). The Shanton and other similar deposits in the Laramie Mountains were examined by Bureau of Mines engineers during 1942, 1943, and 1945, and a report2/ describing the results of a dip-needle survey and surface sampling was published in 1946. The Shanton deposits occur in a relatively flat section of the range at altitudes varying from 7,500 to 1,650 feet (fig. la). Prevailing rocks in the Shanton area consist of anorthosite with intrusive dikes of gabbro differentiates and granite. Titaniferous magnetite outcrops in five masses, which are separated at the surface by overburden and anorthosite.

Jan 1, 1953

Predict the cumulative hydrologic impact of mining on the environment. Approach A comprehensive set of computer models has been developed to predict the impact of mining on ground water. Mine inflows, drawdowns in aquifers, and ground water quality can be predicted. How It Works The Prickett-Lonnquist finite-difference groundwater model was specially modified for the hydrologic problems of mining. This model, developed at the Illinois Water Survey in the 1960's,

Jan 1, 1982

By C. H. Elder

A 5-hole pattern was drilled from the surface at a site near Oak Grove, Jefferson County, Ala., to degasify the gassy Mary Lee coal bed in advance of mining. Gas and water production was monitored for 1 year, 4 months to allow gas flow to stabilize fully. A thickened water stimulation treatment was designed and applied in one hole of the pattern to evaluate this degasification technique for the Mary Lee coalbed. A gas production rate of 70,000 fts/day after stimulation treatment indicates that the use of vertical boreholes coupled with hydraulic fracturing in advance of mining the Mary Lee coalbed would provide for more rapid degasification and could provide a possible source of natural gas.

Jan 1, 1974

By A. T. Coumbe, I. F. Avery

The Bureau of Mines has completed a survey of petroleum pipe - lines by direct correspondence with the oil companies and the use of the records of the Interstate Commerce Commission in order to cover both interstate and intrastate systems . The review shows that crude petroleum and product pipe -lines in the United States had a total length of 152,814 miles on January 1 , 1950 , an increase of 25,463 miles since May 1 , 1941 , the time of the last previous survey . The expansion in pipe -line systems was due largely to new trunk-line construction , as the mileage built to carry refined products increased by 11,880 miles , and those intended for crude -oil transportation gained 6,193 miles . Trunk lines represented 60 percent of all pipe -line mileage on January 1 , 1950 , compared with 58 percent in 1941 . The average diameter of trunk -lines for crude oil , as calculated on the various sizes and weighted according to their respective lengths , increased to 9.8 inches on January 1 , 1950 , compared with 8.4 inches on May 1 , 1941. The mileage for lines up to 8 inches used in crude trunklines has decreased since the 1941 survey , while those of larger sizes have increased . The extensive use of large- diameter oil pipe -lines has developed since the construction of two major lines from Texas to the East Coast at government expense as a World War II emergency measure . The successful operation of these lines proved their economic advantages over smallerdiameter lines as well as their effectiveness in moving unprecedented volumes of oil during the period when tanker movements were restricted by submarine action in the Atlantic Ocean . The 24-inch diameter " Big Inch " line carries over 300,000 barrels daily of crude oil , and the 20 -inch " Little Big Inch " carried over 230,000 barrels daily of gasoline and light fuel oils to destinations where they were urgently needed . Hence , Although these lines were sold and converted to natural -gas service in December 1946 , after fulfilling their wartime mission , their record proved to the industry that significantly lower operating and investment costs per barrel -mile of oil moved could be achieved than were possible with the comparatively small lines in general use up to that time . the several major oil pipe -line projects that have been constructed since the late war are of large diameter pipe . To assure supplies and market outlets of sufficient magnitude to support such lines and provide adequate flexibility , ownership is often shared by several large companies whose transport needs are served in common . The principal recent expansion in facilities has been from supply points in Southwestern States toward markets in the North and East and to Gulf tidewater .

Dec 1, 1950

By L. B. Berger, S. J. Pearce

One phase of Bureau of Mines' work in health and safety is promotion of the use of safe, satisfactory, and reliable respiratory protective. devices. To insure that such devices will be available, the Bureau has established schedules of minimum requirements for self-contained breathing apparatus, gas masks, supplied-air respirators. (hose masks, air-line respirators, and abrasive blasting helmets, hoods, or masks), dispersoid (dust, fume, and mist) respirators, and nonemergency gas respirators (chemical cartridge respirators). Approval tests of self-contained breathing apparatus are conducted by the Safety Branch; approval tests of other types of respiratory protective equipment are conducted by the Health Branch. Both branches are in the Health and Safety Division.

Jun 1, 1950