Search Documents

By G. W. Jones

In the course of experiments on the stabilization of acetylene gas by addition of other gases, notably hydrocarbons such as methane, propane, and butane, it was observed that large quantities of carbon black are produced during the explosion of acetylene or mixtures of acetylene with the, above hydrocarbons, the added hydrocarbon being essentially decomposed into hydrogen and carbon. It is known that in the complete absence of air acetylene explodes upon application of an intense ignition source at pressure above 5.9 p.s.i. gage. The same is true of mixtures of hydrocarbons and acetylene. However, the pressures necessary for explosion are considerably higher in the case of these mixtures and depend on the amount of added hydrocarbon. The present report contains data on gaseous products and the physical characteristics of the carbon black formed by explosion at elevated pressures of various mixtures of acetylene and hydrocarbons as well as other gases, such as hydrogen, helium, nitrogen, and carbon dioxide.

Jan 1, 1950

By C. C. Shale

A semicommercia1, high-temperature electrostatic precipitator and adjunct equipment are described, and operating characteristics at 1,470° F and 80 psig are presented for both positive and negative polarity. Removal efficiency for negative corona waS about 91 to 96 percent while that for positive corona was only about 75 to 77 percent. Results are compared with those from bench-scale investigations, and equipment limitations are discussed. Theoretical aspects of the precipitation process are related to the operating characteristics.

Jan 1, 1969

By D. Montagna

This Bureau of Mines report describes a salt-free, fluxless method for reclaiming metallic aluminum from aluminum dross. The dross is smelted under argon, nitrogen, or carbon dioxide, instead of a salt flux, in an externally heated pot furnace. Aluminum recovery, using argon, is equal to recoveries reported from commercial smelters that process dross in rotary-type furnaces This salt-free method could offer a reduction in air pollution, lower energy requirements by elimination of salts, and the production of up to 60 percent less solid waste for disposal than the salt method.

Jan 1, 1978

By W. A. Grosh

In 1951 the Federal Bureau of Mines became interested in the reports of copper-nickel mineralization in northern Minnesota. Several outcrops on the north side of the Duluth gabbro in the Kawishiwi River area were sampled by the Federal Bureau of Mines and George M. Schwartz of the Minnesota Geological Survey. Because these samples showed appreciable amounts of copper and nickel, a 100-pound sample of an un-altered outcrop was obtained for metallurgical testing. Results from this preliminary work were all favorable; therefore, in the fall of 1953 the Bureau of Mines diamond-drilled three holes near the outcrop of the con-tact between the Duluth gabbro and the Algoma granite. A total of 686 feet of NX size hole was drilled, and 100 percent of the core was recovered. Each hole intersected the contact, and the strike and dip for that locality were established. The core was split, and half was used for analyses and further metallurgical tests; the remainder was retained for permanent record in the Bureau of Mines core-storage warehouse.

Jan 1, 1955

In spite of advances in measurement techniques and an explosive increase in the volume of research, our understanding of human strength remains in its introductory stages. It is clear that muscle strength is a highly complex and variable function that depends on a large number of factors. It is not surprising, therefore, that large differences in strength exist not only between individuals, but even within the same individual tested repeatedly on a given piece of equipment. The issue is compounded by the fact that correlations of strength among different muscle groups in the same individual are generally low, and tests of isometric strength do not necessarily reflect the strength an individual might exhibit in a dynamic test. As a result of these and other influences, great care needs to be exercised in designing, evaluating, reporting, and interpreting muscular strength assessments. Traditionally, tests of muscular strength were in the domain of the orthopaedist, physical therapist, and exercise physiologist. Such tests are also an important tool for the ergonomist, however, because of the high strength demands on workers in manual materials-handling tasks. In some cases, task demands may approach or even exceed the strength that an individual is voluntarily willing to exert in a test of strength. In such cases, evidence suggests that the likelihood of injury is significantly greater than when the task demands lie well within an individual's strength capacity. Because the relationship among strength capabilities, job demands, and musculoskeletal injury has been established, it is apparent that tests of muscular strength may benefit the ergonomist both in designing jobs and in ensuring that individuals have sufficient strength to safely perform physically demanding jobs. Several strength assessment techniques have been employed for these purposes, each possessing unique characteristics and applicability to job design and worker selection procedures. Our main purpose has been to elucidate these strengths and weaknesses, so that tests of strength may be properly applied in designing jobs and selecting workers. One of the crucial points we have emphasized is that any test of strength used in job design or worker selection must be directly related to the demands of the job.(1) For example, if an occupational lifting task has a high dynamic component, a test of isometric strength is not likely to provide the data necessary for proper design of the job. Of course, dynamic strength tests would also be misapplied in assessing a job requiring isometric exertions. Another potential pitfall is using tests of strength on isolated muscle groups and assuming that they are indicative of whole-body strength. For example, one might mistakenly assume that dynamic trunk extension strength represents a person's capability to perform a lifting task. However, an individual's lifting capacity may be entirely unrelated to trunk extension strength. It may, instead, be limited by an individual's arm or leg strength, depending on the task being performed. A final point on strength assessment should be made. An individual's strength capability cannot be considered a fixed human attribute. Strength training regimens can increase an individual's strength capability by 30%-40%. Whether

Jan 1, 1998

By Errol D. Sehnke

This U.S. Bureau of Mines report provides detailed information on worldwide alumina production capacity by plant and country. The information was compiled from a variety of domestic and international sources and was based on information available to the Bureau through December 31, 1993. Capacity data represent announced installed and planned capacities and do not necessarily reflect a Bureau of Mines judgment of actual plant operating levels or timing of planned expansions, The year-end capacity is the ?nameplate" capacity or estimated production capacity, whichever is larger.

Jan 1, 1993

By G. H. Keith

Oxygen and nitrogen cause strain aging in electrorefined vanadium, as evidenced by maxima in yield and tensile strengths and by Snoek internal friction peaks. Alloys containing up to 0.22 percent oxygen and 0.11 percent nitrogen were investigated. Tensile strengths of oxygen-and nitrogen-containing alloys were 66,000 and 68,000 psi at 300° to 400° C, compared with 53,000 and 62,000 psi, respectively, at room temperature. Total elongation decreases to about 7 percent at the temperature of maximum strength. At 600° C, strain aging is not evident. Based on interstitial contents calculated from internal friction measurement, the increases in strength caused by nitrogen and oxygen were 440,000 psi per weight-percent nitrogen and 260,000 psi per weight-percent oxygen. Application of the Schoeck and Seeger treatment to the Snoek effect in these systems results in a calculated lattice distortion of 0.24 and 0.15 caused by the presence of an interstitial nitrogen or oxygen atom, respectively. Alloys containing boron or carbon were also investigated. Both elements refine the grain size but have no other effect because of their low solubility in vanadium.

Jan 1, 1969

By H. B. Brunot

A complete list of permissible mine equipment , tested and approved by the Bureau of Mines previous to January 1 , 1947 , was published as Information Circular 7432.27 A list of permissible mine equipment tested and approved by the Bureau of Mines during the calendar year 1947 was published as Information Circular 7465.3/ The present list supplements Information Circular 7432 and includes all of the equipment approved during the calendar years 1947 , 1948 , and 1949. It therefore supersedes Information Circular 7465. The list also includes an appendix ( No. 2 ) giving the symbol that must be used by every cable manufacturer in marking trailing cables that have passed the test for flame resistance as stated in the amendment of October 21 , 1947 , to Schedule 2E . The items are numbered to indicate the consecutive order in which each type of machine or device was approved in its particular classification . Thus , Information Circular 7432 showed six air compressors on the active list ; five additional compressors , Nos . 7 to 11 , inclusive , in this category were approved during 1947 , 1948 , and 1949 . Several items that were listed in Information Circular 7432 have been repeated in this circular where it was necessary to show that approvals of such equipment were extended to cover an additional voltage rating or other changes . Equipment listed in these circulars is approved by the Bureau of Mines only when found , upon inspection and test , to comply with minimum standards of safety as outlined in schedules prepared on the basis of many years of experience in dealing with safety problems of the coal -mining industry . The use of such equipment in mines known to be gassy , as well as in those that may become so , is earnestly recommended in the interest of safety . This circular is published so that the industry may be kept informed as to the many types of machines , devices , and lamps that are available for reducing explosion and other hazards incident to coal mining . This circular and Information Circular 7432 give the complete list of permissible mine equipment that is available under the various classifications .

May 1, 1950

By Heine Kenworthy

In 1930 the Shenandoah-Dives Mining Co. near Silverton, Colo., put into operation a newly erected, 300-ton selective flotation plant to mill complex ores from its nearby mine. The operation was a steady producer and was enlarged to treat 600 to 800 tons a day. In 1942 the company opened and started milling an area in the mine containing semioxidized ore. The valuable mineral. Content of this ore was considerably higher than in the straight sulfide ore previously handled alone. The mixture of clean sulfide and semi-oxidized ore was difficult to treat; consequently tailing losses, especially with respect to lead, were high. A. few years later, in order to study the possibilities, of obtaining higher recoveries by a modification of the mill flow sheet, a 1,200-pound sample of mill feed, taken over a period of several days by the company, was submitted to the Mississippi Valley Experiment Station for testing. Although this sample proved to contain more than twice as much lead as the average yearly mill feed, the same problem of recovering the oxidized values were present.

Jan 1, 1948

By Jr. Allan

"Although the advantages of large-capacity air receivers for underground mines are plainly evident from published information about various installations in the United States and abroad, details of their construction are not generally known in this country., Ordinary present-day air-compressor installations servicing mining machines are designed to supply air at a specified pressure in sufficient quantity to meet the peak demand of the mine,2/ although this demand may exist for only a few minutes out of 24 hours and, as usually happens, eventually exceeds the capacity of the compressor. Most of the receivers provided with these compressors (to a certain degree of standardi¬zation) are capable of storing a volume of air approximately equal to that compressed in 1 minute by the machine.3, 4/ As a result, during peak-load periods the compressor operates at full load capacity without maintaining kick-off pressure. At other periods of the work cycle, production of compressed air is intermittent.At least one large mine5/ has adopted large-capacity receivers to reduce wear on its air-compressing system caused by the sudden demand of peak loads. Under the old system, the compressors jumped suddenly from half speed to full speed; boilers furnishing steam to the compressors were taxed heavily to provide the increased requirements of power; and machines using the air, among which were four large hoists, were required to operate at 65 pounds per square inch rather than at the 90 pounds per square inch for which the compressors were regulated. Operation of air machines, especially drills, at pressures lower than those for which they were designed decreases their efficiency and increases maintenance costs. In addition, air that comes directly from the compressors has had little opportunity to cool and dry enroute.6./ As a result, quantities of compressor lubricant and water are carried into the machines that use the air. When expansion occurs in the cylinder or turbine of such engines, the temperature of the air drops, and this oil and water is precipitated. The water washes away lubricating oils in the machine, causing poor performance and high cost of maintenance; the compressor oil, in addition to being a poor lubricant for compresed-air engines, exerts a corrosive action on gaskets and rubber hoses.7/Reduction of peak demands on air compressors by large receivers lowers power costs by establishing more nearly constant load factors,8/ and in some cases by permitting the use of smaller compressor capacity.8,9/Load factor is the ratio of average demand to maximum demand; a low load factor costs money.10/Elimination of high-peak demands raises the load factor by making the average and the maximum demand more nearly equal. Further savings may be made possible by large receivers where their use permits charging to be done at night in regions having lower power rates during that period.11/Where ordinary receivers are used, compressor breakdowns cause immediate work stoppages in the mine owing to lack of air. Similarly, the capacity of a large receiver has been known to permit uninterrupted work in the mine until the compressors have been returned to service.9/Large-capacity receivers, either steel-tank or underground rock-chamber, offer a practical solution of many existing problems by providing a sufficient reserve of compressed air within the pressure range required for efficient operation of machines to level off peak demands on the compressor. The com¬pressors operate when the demand has reduced the pressure in the receiver below the regulating pressure and until all air used from the receiver has been replaced. It has been found possible in at least two mines,8.9/ one of which the author has visited, to entirely eliminate one compressor and to obtain more efficient performance from the remaining one by the construction of an underground coal-chamber receiver.8/"

Jan 1, 1950

By Virgil A. Marple, Susanne V. Hering

"5.1 IntroductionTraditional impactors do not offer much size resolution for submicrometer particles; typically their finest size cut is around 0.4 µ.m. Yet for many aerosol applications it is useful to be able to size segregate aerosols in the size range below 0.4 µ.m. Diesel emissions, welding fumes, cigarette smokes and photochemically generated smog aerosols typically exhibit mass median diameters between 0.1 and 0.6 µ.m. When sampling these aerosols with a traditional impactor, fifty percent or more of the aerosol mass can penetrate the final impactor stage. Allhough the material can still be collected on a backup filter, the filter gives no size resolution. As a result, the investigator has no size information on a substantial portion of the sample. One needs a sampler that size-segregates the majority of the aerosol mass. A lower size cut of 0.1 µ.m or less is required for most combustion smokes and smog aerosol s.To obtain smaller cutpoints two types of impactors have been developed, namely low-pressure impactors and micro-orifice impactors. Both instruments can provide cutpoints as small as 0.05 µ.m. Low-pressure impactors were introduced more than twenty years ago (Stem et al., 1962), and a variety of these samplers are in use today. Micro-orifice impactors have been developed at the University of Minnesota within the last five years (Marple et al., 1981 ). To date theirs are the only examples of these instruments in use.5.2 Operating PrinciplesThe low-pressure and micro-orifice impactors use two different approaches to achieve their very small particle-size cuts. Low pressure impactors resemble ordinary impactors, but are operated at reduced pressures of 5-40 kPa (0.05 - 0.4 atm). They take advantage of the decreased aerodynamic drag on particles that occurs when the mean free path in the air is as large or larger than the particle diameter. Micro-orifice impactors operate at near atmospheric pressure, but employ very small orifices, 40 µ.m to 200 µ.m in diameter. The streamlines of the air impinging upon the impaction plate have correspondingly smaller radii of curvature; the air is accelerated more quickly, making it more difficult for the particles to follow. The basic operating principles for both types of impactors are evident from the particle Stokes number, defined as:"

Mar 1, 1989

By B. K. Shibler

During the investigation of the occurrence of manganese deposits in the Western United States, examining engineers of the Bureau of Mines collected 2-ton samples from five manganese properties near Golconda, Nev. Extensive laboratory tests were made to determine the amenability of these ores to standard ore-dressing methods of concentration. The Tom Major property, one of those sampled, is situated 12-1/2 miles south of Golconda, Humboldt County, Nev. The deposit is described as a bed about 5 feet thick in a thinly bedded shale and dolomite formation. The sample tested was obtained from the manganese bed, but the examining engineer reported: "The mining of an appreciable tonnage at reasonable cost would perhaps cut in half the grade represented by the sample."

Jan 1, 1951

By Philip W. Holland

The U.S. Bureau of Mines has designed and built an inexpensive, weatherproof, temperature-controlled cabinet to provide temporary housing for analytical instrumentation. The cabinet consists of an inverted Styrofoam ice chest, an electric fan for air circulation, and a proportional temperature controller equipped with a thermistor sensor and a light bulb as the heater. The cabinet provides a constant-temperature environment for a moisture analyzer and a strip chart recorder when outside temperatures range from -SO to 21° c.

Jan 1, 1993

By G. W. Jones

[A survey of the literature relating to ignition temperatures of acetylene-air and acetylene-oxygen mixtures reveals rather wide disagreement in the reported results. In some instances the ignition temperatures of acetylene-air mixtures were reported to be lower then those of acetylene-oxygen mixtures, which is contrary to experience with other combustibles. To clear up some of the reported discrepancies, the authors have investigated the ignition temperatures of acetylene both in air and oxygen, and their results are presented in this report.]

Jan 1, 1941

By V. R. Miller

The Bureau of Mines has developed a technique to separate and recover the three major components, Pb, Zn, and Cd, from lead smelter flue dust. This research was conducted as part of the Bureau's effort to reduce environmental conflicts and occupational hazards associated with mineral-processing operations and to recover valuable constituents in emissions and effluents. The laboratory process utilizes sulfation roasting of the flue dust followed by water leaching to extract over 95 pct of the cadmium and zinc. Ninety-nine percent of the cadmium was recovered from solution by cementing with zinc dust, and zinc was electrowon from the resulting solution after purification. Zinc electrolysis was carried out in a 1-liter cell at 35° C with a cathode-current density of 8 A/dm2 in a solution containing 65 g/l Zn++ and 180 g/l H2S04, Current efficiencies of 80 pct were obtained. The leached residue consisted largely of PbS04, which was converted to PbC03 and leached with H2SiF6 to produce PbSiF6 electrolyte. Ninety-five percent of the lead contained in the residue was converted to electrolyte. Lead was electrowon from solutions containing 70 gil Pb++ and 90 g/l H2SiF6 using a lead cathode, Pb02-coated titanium anodes at 28° C, and a current density of 1.6 A/dm2. Current efficiencies approaching 92 pct were obtained. Accessory minerals such as cobalt and nickel were separated into purification residues and liquor.

Jan 1, 1982

By Albert E. Long

Preliminary experiments conducted in 1949 with a few diamond bits in which the diamonds in the bit crowns were set in hard-vector directions indicated that a substantial saving could be effected when a high percentage of the diamonds were oriented in this-manner. It was realized, however, that many additional tests would have to be performed before a positive trend could be established and the possibility of coincidence eliminated. Therefore, a long-range series of experiments was planned to investigate various phases of the problems related to the orienting of diamonds in diamond bits. This report (the third in a series) 2/3 presents the information obtained from tests conducted to investigate more fully the effects of orienting high-grade drill bort in diamond bit crowns. In these tests, the drill bort were oriented in both hard-vector and soft-vector directions in the crowns of AX-size bits. Test drilling was done in a dike of saussuritized dacite porphyry similar to a fine-grained granite in hardness e drillability.

Jan 1, 1954

By J. M. Stuve

Low-temperature heat capacities of chiolite (Na5Al3F14) were determined by adiabatic calorimetry in the temperature range 5.8 to 300 K. The derived standard entropy (S°, 298.15) was 115.6 ± 0.2 cal/deg-mole. High temperature enthalpies relative to 298.15 K were obtained by precision drop calorimetry up to 1,000 K. Tables of experimental data and related thermodynamic functions are given for the temperature range of experimental observations.

Jan 1, 1980

By Ronald S. Conti

This U.S. Bureau of Mines report discusses the results of research conducted in the Bureau's experimental mine at Lake Lynn Laboratory on the response of fire sensors to simulated mine fires, which included (1) a slowly developing coal-conveyor belt fire, (2) a rapidly burning liquid fuel-belt fire, and (3) a liquid fuel-belt fire in the presence of diesel exhaust. During these tests, several mine fire sensors were evaluated with respect to sensor placement, spacing, and type. The data indicate that smoke sensors alarm several minutes before CO sensors do; and that, in the presence of diesel exhaust, a prototype diesel-discriminating smoke sensor can successfully function without being sensitive to the diesel contaminants. The vertical placement of sensors in the entry near the fire was also shown to be critical in terms of alarm times. Additional data showed that variations exist in response time and level of response for two brands of electrochemical CO sensor. Results also indicate that early detection of fires will improve the probability of miners' escape, because of reduced smoke concentrations during the incipient stages of the fire.

Jan 1, 2010

By X. N. Hu, X. Shi, V. Vallyathan, N. S. Dalai

"Although silicosis has been studied extensively, the mechanism is still not fully under stood. Experiments do provide evidence that the actions of unique properties of silica surface on the cell membrane are the starting point of silicotic processes. This paper summarizes literature on chemical properties of silica surface, and the effect of particle size on silica toxicity. This paper also discusses the ways in which silica dusts are thought to interact with the cell membrane, with emphasis on freshness, hydrogen bonding, and free-radical interactions.INTRODUCTIONSilicosis is a debilitating pulmonary disease that afflicts persons (miners, foundry workers, ceramic workers, heavy construction workers, etc.) who chronically inhale silica-containing dusts (Schepers, 1960; Silicosis and Silicate Disease Committee, 1988). Since silica is second only to oxygen in weight percentage of the earth's crust (about 28%) and is found in an enormous diversity of minerals, it is natural that silicosis is one of the Major industrial health hazards all over the world. Although silicosis has been studied extensively, the mechanism by which the dusts exert their toxic actions on cells and the processes by which these-actions progress to fibrogenesis are still poorly understood. The biological characteristics of the dusts are largely unknown, although it is suggested that the dust size, shape, surface charge, roughness, surface chemical composition, trace metal content, and crystallinity; dose of silica in the ambient air of the workplace; duration of exposure; genetic variation in exposed sub¬jects; personal respiratory patterns; and presence of any coexisting dis¬ease (such as tuberculosis or rheumatoid arthritis) all influence the ex¬pression of silicosis (Koskinen et al., 1983; Noweir et al., 1980; Raask and Schilling, 1980; Reiser and Last, 1979; Thorne et al., 1985; Wolff et al., 1981). The actual biochemical mechanisms through which these factors operate are still unclear. However, the experiments do provide evidence that the actions of certain unique properties of silica surface on the cell membrane are the starting point of the silicotic process (Allison et al., 1966; Allison and Harrow, 1971; Bateman et al., 1982; Marks, 1957; Parazzi et al., 1968; Reiser and Last, 1979; Summerton et al., 1977). This article summarizes literature on chemical properties of silica dusts and how silica dusts are thought to interact with the cell membrane, with emphasis on hydrogen bonding and free-radical interactions."

Jan 1, 1989

By N. S. Dalal, X. N. Hu, X. Shi, V. Vallyathan

"Although silicosis has been studied extensively, the mechanism is still not fully understood. Experiments do provide evidence that the actions of unique properties of silica surface on the cell membrane are the starting point of silicotic processes. This paper summarizes literature on chemical properties of silica surface, and the effect of particle size on silica toxicity. This paper also discusses the ways in which silica dusts are thought to interact with the cell membrane, with emphasis on freshness, hydrogen bonding, and free-radical interactions.INTRODUCTIONSilicosis is a debilitating pulmonary disease that afflicts persons (miners, foundry workers, ceramic workers, heavy construction workers, etc.) who chronically inhale silica-containing dusts (Schepers, 1960; Silicosis and Silicate Disease Committee, 1988). Since silica is second only to oxygen in weight percentage of the earth's crust (about 28%) and is found in an enormous diversity of minerals, it is natural that silicosis is one of the major industrial health hazards all over the world. Although silicosis has. been studied extensively, the mechanism by which the dusts exert their toxic actions on cells and the processes by which these actions progress to fibrogenesis are still poorly understood. The biological characteristics of the dusts are largely unknown, although it is suggested that the dust size, shape, surface charge, roughness, surface chemical composition, trace metal content, and crystallinity; dose of silica in the ambient air of the workplace; duration of exposure; genetic variation in exposed subjects; personal respiratory patterns; and presence of any coexisting disease (such as tuberculosis or rheumatoid arthritis) all influence the expression of silicosis (Koskinen et al., 1983; Noweir et al., 1980; Raask and Schilling, 1980; Reiser and Last, 1979; Thorne et al., 1985; Wolff et al., 1981). The actual biochemical mechanisms through which these factors operate are still unclear. However, the experiments do provide evidence that the actions of certain unique properties of silica surface on the cell membrane are the starting point of the silicotic process (Allison et al., 1966; Allison and Harrow, 1971; Bateman et al., 1982; Marks, 1957; Parazzi et al., 1968; Reiser and Last, 1979; Summerton et al., 1977). This article summarizes literature on chemical properties of silica dusts and how silica dusts are thought to interact with the cell membrane, with emphasis on hydrogen bonding and free-radical interactions."

Jan 1, 1989