Search Documents

By Paul R. Amyotte, Omotayo Kalejaiye, Kenneth L. Cashdollar, Michael J. Pegg

The Siwek 20-L chamber is widely used throughout the world to evaluate the explosibility of dusts. This research evaluated the quality of dust dispersion in the Siwek 20-L chamber using Pittsburgh coal, Gilsonite, and purple K dusts. A Pittsburgh Research Laboratory (PRL) optical dust probe was used to measure optical transmittance through the dust cloud at various locations within the chamber. A total of 540 tests were performed, with triplicate tests at five nominal dust concentrations and six locations. The two standard dispersion nozzles (rebound and perforated annular nozzle) were compared. The transmissions corresponding to the normal ignition delay period were used to: (a) determine variations in spatial uniformity of dispersion obtained with both nozzles; (b) make comparisons between the experimental transmission data and those calculated from theory for the three dusts; and (c) make comparisons with transmission data measured in the PRI, 20-L and Fike 1 -m3 dust explosion chambers. The uniformity of dispersion for the three dusts was similar with both nozzles, despite the differences in nozzle geometry and mode of operation. Transmission data of the three dusts were all significantly lower than those calculated from theory. This was discovered to be, in part, due to significant reduction in particle size that occurred during dispersion. By measuring particle sizes before and after dispersion, values of 60%, 50%, and 20% reduction in particle size (based on the surface weighted mean diameter) were obtained for Pittsburgh coal, Gilsonite, and purple K, respectively. Transmission data from the PRL 20-L, Fike 1 -m3 and the Siwek 20-L chambers indicated comparable results in terms of uniformity of dispersion. However, transmission data from the Siwek 20-L chamber were significantly lower than those of the PRL and Fike chambers. Again, this was attributed, in part, to the significant reduction in particle size that occurred during dispersion in the Siwek chamber. The design of the outlet (dispersion) valve of the Siwek 20-L apparatus charge vessel was largely responsible for the particle break-up. The contribution to particle break-up by the dispersion nozzles and the high level of turbulence in the chamber were found to be minimal. This is a significant finding in that the dust particle size tested for explosibility in the Siwek chamber is considerably smaller than the original dust sample.

By M. W. Price, Joseph V. Mather, E. H. McCleary

"INTRODUCTION The asphyxiation or poisoning of workmen in underground mines by noxious gases from blasting in adjacent strip mines can be prevented.Considerable progress has been made in eliminating or reducing hazards to the health and safety of underground workmen in anthracite mines, but seldom does a year pass without reported cases of underground workmen being poisoned by the fumes from blasts of explosives in strip-mining operations. In the early days of the anthracite industry, the coal near the surface was only partly mined, and many small stumps of pillars and barrier pillars were left standing; these pillars are now being recovered by stripping. It has become necessary to give more consideration to the effects of blasting at strip mines upon the quality of the air in underground mines adjacent to stripping operations.Special precautions are taken by the .personnel of the Jeddo-Highland Coal Co., whose mines are near Jeddo, Luzerne County, and near Centralia in Columbia and Schuylkill Counties in the anthracite region of Pennsylvania, to prevent asphyxiation of workmen by carbon monoxide or other toxic gases resulting from blasting in strip mines. The procedures established by the Jeddo-Highland Coal Co., are given in this circular so that others may benefit thereby and thus avoid hazards to underground workmen where mining is carried on under similar circumstances."

May 1, 1949

By R. R. Backer

The Bureau of Mines, in cooperation with Washington Irrigation and Development Co. (WIDCO), evaluated the dewatering of fine coal-refuse slurry using chemicals and various types and combinations of drains in natural earth impoundments. About 40 lb of lime and 2 lb of polymer per ton of dry solids were mixed with the underflow from the preparation-plant thickener. Clear, free water was immediately liberated from the slurry. The percent solids by weight of the slurry increased from about 17 to 30 immediately, and after 5 days increased to 45 wt-pct. This indicates a threefold reduction in total volume after 5 days from 172 cu ft/ton solids originally to 56 cu ft/ton solids.

Jan 1, 1981

By J. E. Chilton, C. R. Carpenter

The U.S. Bureau of Mines has developed an intrinsically safe carbon monoxide (CO) monitoring system for mines by coupling a fiber-optic data telemetry (FODT) system with a prototype electro- chemical CO monitor. The CO monitoring system can be used in a coal mine as one component of an early fire warning system. This system may be used in belt haulage entries when the entries are used for supplying ventilation air to working places. The FODT accepts a 0.1- to 1.1-V analog signal from the monitor and converts it to pulses (0 to 5 V) at frequencies from 1.1 to 11 kHz that drive a light- emitting diode (LED). An electrically nonconducting fiber-optic cable carries the LED signal to a remote receiver. The receiver analyzes the incoming light signal and displays the measured CO concentration in parts per million. This report discusses the performance of the FODT system and characteristics of the CO monitor such as response times, linearity, and temperature and pressure effects.

Jan 1, 1992

By A. J. Kraemer

For a number of years the Bureau of Mines has conducted semi-annual survey to determine the changes in the characteristics of the rotor gasoline being sold in the United States. Certain cities have been decided upon as points of origin of samples. Tare choice of these cities has been governed by their situation as the representative of a more or less definitely bounded marketing territory. Samples have been taken on or about the fifteenth day of January and July of each year. In the collection of the samples an attempt has been made to get a representation of the important types of motor fuel being sold, and also to tame into consideration the proportion of tie total consumption that is supplied by the different marketers. It is therefore felt that the survey affords a reliable indication of the quality of the gasoline being sold throughout the United States at the time of sampling. The figures in Table I, below, were obtained by averaging the end points of the least volatile and most volatile samples of gasoline. For example, of 850 samples analyzed in 1919, the 10 per cent (85 samples) having the highest end points, and the 1C per cent having the lowest end points were averaged. These averages are represented in the table as the "Maximum 10 per cent" and the "Minimum 10 per cent", respectively. The same scheme was used in the succeeding surveys.

Jan 1, 1925

By J. M. Singer

The objective of this investigation was to determine minimum air velocities and entrainment rates for coal and rock dust dispersion in wind tunnel experiments under conditions that simulate dispersion from surfaces in coal mines where airflows are induced by weak gas explosions. Dust deposits were bed-or ridge-shaped; particle sizes were 6 to 80 microns (cohesive deposits) or 100 to 150 microns (free-flowing deposits); and wind tunnels were 7.62 cm wide by 5.08 cm high by 300 cm long, and 2.4 m wide by 1.5 m high by 215 m long. The investigation showed that minimum air velocities (directed at mid-height) of separate, layered, or mixed piles of coal dust and rock dust were within the range 5 to 30 m/sec, independent of size of wind tunnel. This finding considerably facilitates scaling of data to mine-size passageways. Free-flowing deposits dispersed relatively slowly by single-particle detachment; cohesive dusts dispersed faster by the breaking and lifting of large clumps along weak failure flames; particle dispersion occurred in flight. Layered or mixed deposits of coal and rock dust did not disperse selectively. Semiempirical expressions were derived relating minimum air velocities and dispersion rates to dust-pile geometry, cohesion, porosity, and bulk density.

Jan 1, 1972

By T. M. Nasiatka

This report sterns from a study undertaken by the Federal Bureau of Mines to determine the possibility of reducing filter-cake moisture by applying radiant heat. Suitable laboratory equipment was set up to study the effect of heat, heating time, proximity of the heater to the filter cake, cake thickness, and other variables related to the final filter-cake moisture. A minus-48-mesh coal slurry and application of heat for 60 seconds resulted in filter-cake moistures 5.6 to 13.2 percentage points lower than could be accomplished by filtration alone at 24 inches of Hg for 1-1/4-and 1 1/2-inch cake thickness, respectively. The moisture reduction can be attributed to the combined effect of lower fluid viscosity and evaporation.

Jan 1, 1959

By S. J. Broderick

"INTRODUCTION Dark soils are commonly believed to be better for agricultural purposes than light-color soils. Much of this feeling may be purely psychological, as many persons have unconsciously acquired the habit of associating richness of soil with color light soils, however, may be just as rich in humus and plant foods as the best of the dark soils. A dis-cussion of the manifold attributes that play an important role in soil technology is beyond the scope of this paper, but the color factor will be considered, as it has a particular bearing on some field experiments using coal-mine waste as a darkening medium.It has been established that dark soils absorb more of the sun's radiation, consequently are maintained at a higher temperature than light soils. This physical principle is applied in our daily lives in the choice of clothing. White clotnes in summer are cooler than dark ones. Conversely, dark clothes in winter are warmer than light-color clothing. A decided advantage of dark soils over light soils is the higher average temperature of the former, resulting in an earlier maturing crop. This advance of the maturing season may range from a few days to a month, depending on such factors as climate, crop, and degree of color of the soil. It has been reported that in parts of Russia where the growing season is short, perhaps comparable to that in Pennsylvania and. New York, cotton has been grown successfully on soils originally of light color, but darkened with coal, dusts. The growth of cotton is, accordingly, speeded up a full month. 3/"

May 1, 1940

By Steve Bessinger, Steve Signer, James Pile

The San Juan Mine and the National Institute for Occupational Safety and Health conducted a study to measure how development mining affected bolt loads. Twelve fully grouted, instrumented roof bolts were installed at two three-way intersections as part of the standard bolting pattern. Newly developed miniature data acquisition systems (MIDAS) were used to measure bolt load changes during initial face advance and cross-cut breakthrough. The effects of cut placement and depth on roof bolt loads were studied. This test showed how bolt loads increased at five positions along the bolt length during initial mining. Both entry advance and cross-cut breakthrough produced a similar percentage of increase in bolt loads. Geologic differences between the test sites were probably responsible for the differences in amounts of bolt loading. The test site with more top coal and a higher rock quality designation (RQD) had lower bolt loads.

By K. Robert Dorman

This Bureau of Mines report describes laboratory and field experimentation in building mine ventilation stoppings, air-door frames, and fan bulkheads with a civil construction technique. Shotcrete is applied to a free-standing, three-dimensional wire-truss panel, which is easily cut and rapidly erected. In mines where shotcrete equipment is available, this technique should be faster and cheaper than conventional block-and-mortar or monolithic concrete construction.

Jan 1, 1980

By R. V. Ramani, A. S. C. Owili-eger

A mass balance equation can be written for the unit block of Figure 7 for changes within the volume during time At as: [ ] where x and y are the coordinates; q is the flow across any surface; p is the density of the fluid flowing through the medium; qvol is the volumetric flowrate; @ is the medium porosity; and Ax and Ay are the dimensions of the block. The subscripts t and (t+At) denote time levels and At is the change in time. Writing this equation in nota- tional form and on rearranging, the following expression is obtained:

Jan 1, 1974

By Lester G. Morrel

THE RICH and varied occurrences of metallic ores in Australia, extensive nickel deposits on New Caledonia and phosphate rock on several widely scattered small islands were important aspects of the economy of the South Pacific area. Relatively small quantities of gold and nonmetallic minerals produced in New Zealand, Fiji, and the Territory of Papua-New Guinea remained important to the domestic economies of these islands, but had little importance to overall world mineral supplies. The value of mineral commodities produced in this area in 1964 was estimated at $658 million,3 compared with $585 million in 1963. The year's greatest commodity gains were in bauxite and aluminum, beryl concentrate, manganese ore, nickel smelter products, tin, and coal. Annual increases were recorded in virtually all countries and possessions in the area except Papua-New Guinea, where the drop in output of alluvial gold accounted for a decline of about $160,000. Mineral industry activities in Australia overshadowed those in all other parts of the South Pacific in 1964. Outstanding developments were the sales contract negotiations and physical preparation for exploiting the rich iron ore discoveries in Western Australia, the initiation of domestic crude oil production, the commissioning of two new steal mills and an alumina refinery and a start on the new alumina-aluminum project based on Cape fork bauxite deposits. The principal mineral development in 1864 in New Zealand was the progress on plans of the Newzealand Steel Co. to use indigenous iron sans as the resource base for a local steel industry. In New Caledonia, additions and expansion of the nickel mining and smelting facilities continued throughout the year. Plans for extensive geophysical studies were announced by the Government Geological Departments of British Solomon Islands and Fiji.

Jan 1, 1966

Develop a more efficient method of testing the integrity of in-situ leach mining operations. The Problems For economic and environ-mental reasons, in-situ leaching operations must be sure that wells do not leak. Loss of solution in large quantities can be expensive in itself, and if such losses result in pollution the costs can be even higher. Wells are usually tested for leaks by sealing them with packers, pressurizing them and monitoring the pressure drop. However, many commercially-available packers are designed to be used in steel-cased wells rather than the fiberglass-or plastic-cased wells used for in-situ mining. These packers are heavy, cumbersome, expensive, and often leak. In addition, commonly used well-integrity-test systems require lengthy test periods and drill rigs or hoist trucks with rigid pipes must be used to run the packers in and out of the well. The Bureau of Mines has developed a mobile, self-contained leak-testing system that is faster, uses trailer-mounted equipment that can be operated by one person, and features a new inflatable packer.

Jan 1, 1985

By J. K. Richmond

Early research on coal dust explosions by the Federal Bureau of Mines and in other countries is reviewed to examine the effect of a single inhibitor, rock dust, on the explosion limits of coal dust. The parameters studied in this research included coal dust fineness, volatile content, and type of initiation. This research resulted in appropriate safety regulations in the respective countries. Also reported are the results of recent research in the Experimental Mine of the Bureau of Mines to investigate in detail the limits of coal dust explosions; the research used three types of coal with rock dust added as the independent variable. New experimental techniques and new criteria for defining propagation/nonpropagation were applied to the experiments. Also, a limit explosion propagation model is proposed based on the assumption of rapid devolatilization of the coal particles, with the subsequent combustion of the evolved volatile products contributing primarily to the propagation of the explosions. The model assumes also that the resultant char acts mainly as an inert diluent similar to the rock dust. The model also suggests that the function of stronger initiation is mostly to lift more dust from the mine surfaces.

Jan 1, 1975

By James E. Bell

Quartz crystals occur on a farm in the vicinity of Laurel Fork, Carroll County, Va., in abundance over a large area, This has been known for several years, but no work had been clone, up to the Bureau of Mines examination in 1943, to determine the amount of crystalline quartz of usable quality. Field exploration was undertaken throughout the month of June 1943.

Jan 1, 1950

By James A. Powell

The theory of electromagnetic fields indicates such fields could be used to detect and locate trapped miners. To be useful, the hardware of the system must meet a number of requirements, including small size, intrinsic safety, and rugged construction. Such hardware has been built, and the system has been tested by the Bureau of Mines and its contractors. These tests indicate that the electromagnetic method provides a practical means to locate miners in emergencies.

Jan 1, 1976

By S. R. B. Cooke, F. D. DeVaney

"INTRODUCTION The potash mineral receiving the most attention in the newly discovered. New Mexico-Texas potash district near Carlsbad, N. M. is sylvite (potassium chloride). Sylvite contains more potassium than any other mineral. Merchantable high-grade deposits have been found, and those of lower grade may be enriched to a high degree of purity by refining methods. Deposits containing sylvite were the first to be developed and axe the only ones being mined.However, many other minerals that contain potash occur in the salt beds of the Carlsbad District. Of these the more important are polyhalite, carnallite, langbeinite, leonite, and kainite. The nature of the deposits and their mineralogy have been described in detail by members of the United States Geological Survey. 4/Langbeinite, although not so abundant in these deposits as carnallite and has particular interest because the potash is in the form of the sulphate and as such commands a premium in terms of K20 unit. This is explained by Fox and Turrentine 5/, who state:"

Feb 1, 1936

By M. M. Hassan

This report describes the analysis tools developed at West Virginia University which can be implemented to optimally design coal mine electrical systems. The basic analytical tools for all power systems are the load-flow and short-circuit analysis. Well known programs have been developed for analysis of ac transmission and distribution systems, but they are not applicable to a system which has combined ac/dc distribution, such as a coal mine power system. Furthermore, the topology of a coal mine electrcal system changes continuously due to the movement of the locomotives on the track. In the first section of this report, algorithms for carrying out load flow and short-circuit analysis of a coal mine electrical system are described. Results from the study of a typical coal mine system are presented. In the second section a method is described to optimally size power cables for cyclic loads. The method is based on the development of a thermal-electric model for a low-voltage power cable. Results from experimental verification of the model are also presented. These techniques are useful in the safe, efficient, reliable and economical design of the coal mine electrical power systems.

Jan 1, 1979

By Ronald S. Conti

This paper describes technology and training that has been identified for underground emergency responders. Historically, underground mine rescue teams have only received training in the course of actual emergencies, or in simulated mine environments, usually on the surface, with placards to identify objects and hazards. Also, while U.S. Federal Regulations require all underground miners to walk escapeways and conduct fie drills every 90 days in a smoke-free environment, this does not fully prepare them for the conditions that will be encountered in real escape situations. Therefore, it is extremely important that miners are provided with adequate technology and that training simulations are conducted in a realistic manner. A series of mine rescue training and mine emergency response development (MERD) exercises, and in-mine smoke training was developed, conducted, and evaluated by state and company teams, and by National Institute For Occupational Safety and Health (NIOSH) personnel. The training exercises were held at NIOSH's Lake Lynn Laboratory (LLL) and operating mines during the past several years. This training resulted in improved technology and training for mine rescue teams, fire brigades, first responders, and miners in general. For example, existing technologies were identified to help responders during exploration and recovery operations. These included various chemical light shapes, strobe lights, light vests, and laser pointers to identify team members. Most of these devices may be used to mark underground areas and certain mine materials. Strobe lights were used for mapping out escapeways and lasers were used to negotiate travel through smoke. Thermal imaging systems allow rescue personnel to see in darkness and through dense smoke, and allows the user to easily locate missing or trapped personnel and heated areas. A hands-free communication system showed potential for enhanced communications between team members, the fresh air base, and command center. A new team lighted-lifeline allows for flexibility in movements of team members during routine tasks and allows them to easily find their fixed position on the lifeline. Of all the technology evaluated by underground personnel, laser lights and lifelines were most beneficial in leading personnel to safety and out of the mine in smoke-filled passageways. A positive-pressure inflatable escape device (IED)/airlock, was used to isolate the "hazardous" environment from fresh air and allow rescue team members to traverse through. An inflatable feed- tube partition that can rapidly block large openings such as underground passageways or tunnels and simultaneously provide a feed-tube for high-expansion foam generators was also deployed during the simulations. These technological advancements have improved the state of readiness for rescue personnel and have increased the chances of survival for all personnel escaping from underground emergencies.

By R. W. Stahl

One of the broad purposes of the Bureau of' Mines since its establishment has been conservation of mineral resources. As some of the coal beds approach depletion, especially those coals suitable for making metallurgical coke, more and more attention is being given to means of recovering a larger percentage of coal in place. The customary system of mining in the United States is by room and pillar, or some variation thereof, which leaves pillars of coal to support, the roof. In many operations, where the pillars are not systematically recovered, the loss of coal often amounts to 50 percent or more of the original deposit. In many instances in developing new mines, It is planned to recover chain and barrier pillars on retreat when the mine has reached established boundaries. Too often, however, mines are abandoned for some unforeseen reason before completion of mining without recovering any pillars. Usually, these pillars are lost forever. With this in mind, the Mining Division, Region VIII, of the Bureau; of Mines is encouraging mining by longwall methods. It is a generally known fact that almost all of the European coal is mined by longwall methods, which are conducive to a high percentage recovery of coal. A comparison between mining systems usually is on the basis of tons per man per shift. Unless all operating conditions are similar, such a comparison could be misleading. Generally, the output per man shift in European longwall mines is less than that obtained in room-and-pillar mining in the United States. In European mining, maximum recovery of coal is not only mandatory but it must be accomplished without major damage to surface by subsidence. These restrictions necessitate packing or stowing with consequential increases In manpower and decreases in output per man shift.

Jan 1, 1954