Search Documents

By Suresh K. Bhatt, Gary L. Mowrey, Timothy R. Rehak, David K. Ingram

Coal and nonmetal mining used about 4.3 billion pounds of explosives and blasting agents during 2001 in the United States. A major part of this consumption was related to surface mining. Mine Safety and Health Administration accident data indicate that flyrock and lack of blast area security were the primary causes of blasting-related injuries in surface mining. Fatal injuries due to lack of blast area security were primarily caused by failure to clear blast area or inadequate access control to the blast area. At a coal mine, a neighbor walked into the blast area and was fatally injured. The blaster could not see the victim entering the blast area from the firing station. In another case, a passenger in a vehicle was fatally injured by flyrock because highway traffic was not monitored during the blast. In another example, a dozer operator entered a blast area due to lack of access control. Several fatalities resulted from using inadequate or no blasting shelter. A crane operator was fatally injured while standing in the open about 120 ft from the blast site. In another instance, a helper, standing about 150 ft away from the edge of a blast, was fatally injured by flyrock. In a limestone mine an equipment operator was fatally injured while guarding access roads in a pickup truck. This paper briefly describes six representative fatalities due to flyrock and lack of blast area security in coal and nonmetal mines. Several mines were visited to collect information relative to working practices aimed at mitigating blasting hazards. Salient information obtained through these visits is presented.

By James P. Rider, Jeanne A. Zimmer, Andrew B. Cecala, Robert J. Timko, Earle H. Andrews

Many different types of structures and materials have been used to build mineral processing facilities over the past few decades. Although the structure type and building material were not viewed as significant factors affecting the health of employees in these facilities when they were built, the National Institute for Occupational Safety and Health performed an evaluation to determine to what extent building types could impact respirable dust and noise levels. This report discusses the evaluation of three different types of product sizing silica sand structures: a masonry design, a steel-sided design, and an open structure design. The data obtained in this study indicate that the open structure design (no walls) was superior from both a dust and noise (health) standpoint compared to the other two structures. The open structure design should also be beneficial from a cost standpoint because of lower material and construction costs. Companies and design engineers should consider this open design when building new mineral processing facilities in climates where it could be applicable. Some companies may also want to consider modifying existing structures with a more open design to further reduce dust and noise levels. As the trend continues in lowering allowable dust levels for federal health standards in the U.S. mining industry, the open structure design may be an approach for some companies to consider for their operations.

Jan 11, 2006

By R. H. Nafziger

As part of its program to help decrease the dependency of the United States on foreign imports of nonfuel minerals and to devise technology for the efficient and economic use of domestic resources, the Bureau of Mines smelted and sulfation-leached an ilmenite from northern Minnesota. The objective was to assess the feasibility of preparing chlorination-grade titanium feedstock. The concentrate was smelted with woodchips, coke, and soda ash in 91-kg-and 1-metric ton (mt)-capacity electric arc furnaces to form Ti-rich slag and commercial-grade pig iron. The slag contained from 67 to 77 wt pct titanium oxides and from 1.8 to 7.2 wt pct iron. Sulfation occurred in a 4.5-kg/h moving-bed reactor using S02-air mixtures at temperatures of 8000 to 8500 C to form soluble salts of the Ca, Mg, Mn,and Na impurities, which cause plugging of fluidized-bed chlorinators. Subsequently, the sulfated slag was leached in acid to remove the soluble sulfates. The final product from small-scale testing contained up to 95.5 wt pct Ti02, a minimum of 0.6 wt pct Fe, and a minimum total of 0.3 wt pct of the four impurities of interest. The final product meets charge specifications for chlorination. However, more large-scale testing is necessary.

Jan 1, 1987

By David F. Smith

The American Society for Testing Materials4 has recommended that the melting temperature of potassium chromate be used-for indicating the temperature to which a coal sample should be heated in the standard method of analysis to determine its volatile matter content. The specified temperature is 950± 20° C., the melting point of potassium chromate being noted as 940° C. Le Chatelier5 originally found the melting point to be 975°; later6 he found 9400. According to Shemtschushny7 the melting point is 984°; he also found a transition at 679°. Groschuff8 found the melting point to be 971° and the transition temperature 679°. Amadori9 reports a melting point of 9.78° and a transition point of 666°. The International Critical Tables10 take the melting point as 975°, which is estimated to be correct to two significant figures. In view of the apparent uncertainty existing, it has been though worthwhile to make a careful redetermination of this datum. It is of interest not only to determine the melting point of the pure salt, but also of the commercial product, in order to test its suitability for use as a temperature indicator. The work was suggested by A. C. Fieldner, chief engineer, experiment stations division, U. S. Bureau of Mines.

Jan 1, 1929

By Harry Dobroski, Larry G. Stolarczyk

Theoretical and experimental research sponsored by the U.S. Bureau of Mines shows that medium frequency (MF) electromagnetic (EM) signals propagate great distances in an underground environment such as a tunnel or mine. This propagation is enhanced by different mechanisms associated with the geology, and with the existence of metallic conductors in the entryways. In stratified geologies, a transverse electromagnetic (TEM) mode of signal propagation is possible if a low conducting layer is bounded above and below by higher conducting layers. In general, the difference in conductivities must be at least several orders of magnitude. Such geological waveguide conditions often exist in underground mines. Propagation via the waveguide effect is known as the "seam mode" of propagation. Another mode of propagation, the "tunnel mode," exists in underground entries with electrical conductors such as power cables, metal pipes, and phone lines. A monofilar mode of propagation exists when signals are impressed upon conductors and return via the surrounding rock. A bifilar mode of propagation exists when all signals exist only on local conductors. In a given location there is a combination of monofilar and bifilar modes that make possible an interaction between the conductors and a transmitting device in a tunnel or entryway. Signals can be impressed on or received from local conductors via magnetic dipole antennas (loops) or line couplers.

By J. I. Paige

The Bureau of Mines, U.S. Department of the Interior, conducts research on methods to minimize the requirements for mineral raw materials through conservation, substitution, and increased minerals and metals recovery from primary and secondary domestic resources. To further this goal, prior Bureau research had devised a pyrometallurgical technique (RI 8211) to recover metallic iron and copper from molten copper smelting furnace slags by carbothermic reduction. As a continuation of this Bureau research on the carbon injection technique, reverberatory and electric furnace slags were treated in an 800-kva electric arc furnace by simultaneously top feeding the slag and injecting coke breeze into the bottom of the molten bath. Results of the tests show that 76 to 89 pct of the copper and up to 48 pct of the iron contained in the smelting furnace slag were recovered in a metallic phase, while 56 to 82 pct of the carbon injected into the sys-tem was utilized as the reductant. Laboratory evaluation has shown that the metal product, which contains 86.9 to 95.0 wt-pct iron and 1.3 to 4.1 wt-pct copper, will be a satisfactory medium for recovering copper by cementation. The expected energy consumption for the process is 110 kwhr per ton of molten slag treated and 520 kwhr per ton of solid material charged.

Jan 1, 1982

By Maria I. De Rosa, Charles D. Litton

The National Institute for Occupational Safety and Health (NIOSH/PRL) con­ducted a series of large-scale experiments to evaluate the effectiveness and safety of various concentrations of an inert gas mixture (CO2,8%;N2, 50%; Ar, 42%) for preventing and sup­pressing cab ?res. Comparison of concentrations effectiveness in yielding safe times has led to the choice of an optimum gas mixture concentration, discharged in the cab through a muf?ed nozzle system, for the development of a dual cab ?re inerting system. Of note is that safety training programs, including the synchronization of performed tasks, need to accompany this technology to enhance operator’s ef?ciency and safety during ?re emergencies within the safe times yielded by the cab ?re inerting system. Cab ?res are caused by the ignition of ?ammable vapors and mists (ball of ?re) that penetrate the cab during prolonged hydraulic ?uid and fuel ?res, and electrical malfunctions involving other cab combustible materials. Often, these ?res force the operator to exit the cab under hazardous conditions during a time needed to perform emergency tasks. Hence, it is important to provide the operator, not only with an engine fire suppression system (dry chemical powder), but also with a cab ?re protection system, effective both in preventing the ignition of ?ammable vapors in the cab, and suppressing cab material ?res.

Objective To develop a passive, inexpensive technique for monitoring explosion overpressures within sealed areas in underground coalmines. Background From 1994 to 2000, seven explosions of methane and/or coal dust occurred within the worked-out, sealed areas (gobs) of underground U.S. coal mines. These explosions, believed to have been started by lightning, destroyed many seals and caused much damage external to the sealed area. One gob explosion went undetected until the mine operator reopened the sealed area and discovered the damage. Fortunately, these gob explosions did not cause any fatalities or injuries. Because lightning occurs in just about all mining areas, several questions arise. Could gob gas explosions be occurring in other sealed areas and going undetected? If so, what is the magnitude of the resulting explosion overpressures? The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) undertook a study to identify and evaluate passive measuring devices to monitor and quantify the overpressures associated with such explosions. This work was done in parallel with full-scale explosion experiments for evaluating the strength characteristics of seals used for isolating areas in underground coal mines. Approach Evaluation studies were done in PRL's 20-liter explosion test chamber and in the full-scale Experimental Mine at Lake Lynn Laboratory to evaluate the response and accuracy of various commercially available automobile tire pressure gauges to overpressures generated from gas and dust explosions. The first series of tests was done in the 20-liter chamber, which is used to study the explosibility and inerting of fuel dusts and gases. Data from the tire pressure gauge tests were compared to the pressure-time data obtained from the 20-liter chamber 's traditional electronic strain gauge pressure transducer recorded on a high-speed data acquisition system. To evaluate the tire pressure gauges, the valved inlet (tip) of the candidate pressure gauge was removed and the body of the gauge was cemented with epoxy into a 0.25-in pipe elbow and attached to the outside of the test chamber. A second series of tire gauge evaluation tests was done at Lake Lynn during explosion-resistance testing of seals used in underground coal mines. Full-scale seals (20 ft wide by 8 ft high)were constructed as one wall of a 2,000-ft3 chamber and exposed to a series of methane explosions. Average overpressures ranged from20 to 80 psi. The seals were built with various strength materials ranging from 7 to 48 in thick. The modified tire gauges are attached on the outside of the chamber to a 0.25-in NPT pipe that extends into the chamber (figure 1). The axis of the gauge is mounted at a right angle to the plane of the seal to minimize the coupling of any seal movement to the stem of the gauge that may cause inaccurate readings. The internal explosion pressure history is recorded with a strain gauge pressure transducer mounted inside the chamber. Methane is injected into the chamber, mixed with air, and ignited with an electric spark located at the geometric center of the chamber. Maximum explosion overpressures are recorded and compared with the tire gauge pressure.

Jun 1, 2001

By Bruce D. Hanson

The Bureau of Mines conducted a series of experiments using four different coal types to determine the effect of attack angle and symmetric bit wear on airborne respirable dust (ARD) generated by point-attack bits and in energy consumption. Neither had a significant effect on ARD at the 95-pct confidence level, but bit wear had a significant effect (95 pct confidence) on specific energy (energy per gram of cut coal) for three coal types, Depth of cut was the most significant factor affecting ARD and specific energy.

Jan 1, 1979

By David C. Oyler, Paul W. Jeran, William P. Diamond

The Bureau of Mines is cooperating with the U.S. Department of Energy in a directional degasification project at the Emerald mine near Waynesburg, Pa. This project is designed to combine the highly successful underground horizontal degasification technology with surface drilling methods. The objective of this program is to demonstrate that directional drilling can be used as a technique for degasifying coalbeds ahead of mining to reduce the hazards of methane-air explosions in coal mines. The directional hole at the Emerald mine is designed to start vertically and enter the Pittsburgh coalbed horizontally. A 3-inch-pilot hole entered the Pittsburgh coalbecl at a vertical depth of 999 feet, The hole will be reamed to 8-3/4 inches in diameter, and 5-1/2-inch casing will be cemented in place. Three individual 3-inch-diameter, 3,000-foot horizontal gas collection holes will be drilled into the coalbed in a “bird foot” pattern. A corehole and vertical dewatering hole have been completed at the anticipated coalbed intercept. The dewatering hole was drilled to130 feet below the Pittsburgh coalbed, a depth of 900 feet, and 880 feet of 7-inch-OD casing was cemented in place. Seven vertical holes for monitoring the extent and progress of degasification have been drilled within the horizontal drilling area.

Jan 1, 1979

By Jan M. Mutmansky, Christopher J. Rise

"One of the most serious long term health problems associated with underground,mining is Coal Workers Pneumoconiosis (CWI'), more commonly known as Black Lung Disease. It occurs in some coal workers, normally after 15 or more years of exposure to coal mine dust, and leads to a variety of respiratory problems. Two types of pneumoconiosis are recognized simple CWP, which has been estimated to affect 6.9 percent of miners and is a condition that does not impair the miner's ability to work nor reduce life expectancy; and a more severe form of black lung (called progressive massive fibrosis) that occurs in about one percent of the cases and results in severe lung damage.Although the relationship between coal dust and CWP has long been recognized, detailed knowledge of the relationship is insufficient for setting up authoritative guidelines to reduce the health risks for those employed in dusty,underground environments. CWP is not only a health problem for workers that causes considerable distress, it is also a very expensive problem the total annual costs associated with CWP approach two billion dollars.As part of its efforts to combat CWP, the U.S. Bureau of Mines in 1983 established a Generic Mineral Technology Center to carry out basic research into all aspects of respirable coal dust:— control of dust generation — the behavior of dust in the mine — characterization of dust particles interaction of dust and lung— the relationships among dust generation and mobility and the mine environment, geology, and seam characteristics,Penn State, West Virginia University, the University of Minnesota, and the Massachusetts Institute of Technology are involved in this research, which is administered from the Department of Mineral Engineering at Penn State.Our work is one of the seven projects to be conducted at Penn Slate. We are concerned particularly with the characterization of dust and its relationships with the mine environment, and our main goal is to establish standard procedures for describing and measuring these variables.Coal DustCoal dust is a very complex material that varies greatly in chemical and mineralogical properties. Moreover, it is not the only constituent of respirable dust in the mine. When a coal seam is mined, it is inevitable that rock particles other than coal are included in the material. This rock comes from the mine roof, the floor, and the partings and inclusions within the coal scams. Since the roof and floor strata, the partings and inclusions are often stronger than the coal, mining them frequently causes more dust than mining the coal itself. One of the objectives of our research is to find the relationships between a specific coal's characteristics before it is mined and the respirable dust characteristics after it is mined. We are particularly interested in the size distribution of particles, the chemical properties, and the mineralogical properties."

Jun 1, 1988

By John J. McClelland, Gerald T. Homce, John R. Thalimer

The U.S. Bureau of Mines has investigated the early detection of insulation failure in squirrel cage induction motors for the past 4 years. Research was done using a sophisticated empirical data-modeling technique based on values calculated from a motor's voltage and current phasors. This technique produces two polynomial equations that calculate the insulation leakage current and power. These models were implemented in a prototype system that monitors six motors on a continuous miner for insulation leakage. These insulation leakage values are used to anticipate insulation failure. The system consists of a motor-data-system for each motor on the machine and a control computer located away from the miner. Each motor-data-system consists of an analog interface to the motor's voltages and currents, a single-board computer that reads digitized data and calculates voltage and current phasors, and a bus node that interfaces the single-board computer with the rest of the system by way of a serial bus system. Using this bus system, the control computer requests and receives phasor data from the motor-data-systems. From these data the control computer calculates and displays two deterioration values for each motor, for leakage current and power, using Bureau-developed models. These values are stored in a data base from which the user can display graphs of each motor's deterioration values over time.

Jan 1, 1992

By W. J. Pena, C. W. Owings

"Generally, the hazard of cool-dust explosions in tipples and cleaning plants is not given the consideration that is given it underground. This lack of consideration is probably due to failure to appreciate the potential hazard. An explosion in a tipple or cleaning plant is basically little or no different from an explosion underground. If bituminous-coal dust is raised into a cloud in the air and comes in contact with arcs from motor brushes, switches, or open flame, the dust is very likely to ignite, and flame will very probably propagate or extend through it if the quantity of dust per unit of air space is sufficient. The open space in a tipple or cleaning plant may reduce the violence of the explosion, but it is not likely to prevent ignition or propagation of flame.The movement of coal through a tipple or cleaning plant naturally puts into suspension a large amount of dust, which finally settles on exposed surfaces. Any disturbance that will put this dust into suspension in a sense enough cloud can result in the dust being ignited by an arc or open flame if one should be present. An explosion of bituminous-coal dust in a tipple or cleaning plant generally can be prevented either by keeping it thoroughly clean or by removing all sources of ignition, or both.The tests at the U.S. Bureau of Mines Experimental mine have shown that the explosibility of coal dust is proportional (other things being equal) to the ratio of the volatile matter to the volatile matter plus the fixed carbon, indicated thus:The volatile ratio for the Pittsburgh coal bed is calculated as follows:Therefore, as the volatile matter decreases the liklihood of ignition decreases; however, coal-dust explosibility depends on other factors also, such as fineness, dryness, and cloud density; and under some conditions other factors also intervene.Proof of the explosibility of coal dust in the absence of explosive gas has been shown in numerous cases in mines and mine plants and also by a series of tests. In these tests a dense cloud of dust is blown onto an open flame or an electric arc, almost invariably with resultant exploding of the dust. The Safety Division of the United States Bureau of Mines has made a number of demonstrations of the explosibility of Pittsburgh coal-bed dust, using a small gallery or box in which a cloud of coal dust is blown onto a lighted match; larger-scale tests have been made with an electric arc as the igniting agent. Bituminous-coal dust is readily ignited with a medium arc, but with low-volatile coals a larger arc is required. For test purposes, a 100-ampere arc has been used. Ignition has occurred readily under these conditions with Pocahontas No. 5 coal dust with ratios of volatile to total combustible of 0.232 to 0.253, and with Pocahontas No. 3 coal dust with a combustible ratio of 0.242. Lower Kittanning coal dust, with a ratio of 0.187, did not give definite ignitions, and Pocahontas No. 4 dust did not explode, although part of the coal-dust cloud ignited. It is probable that even the low-volatile coal dust will be found to be explosive with a higher-amperage electric arc as the initiating agent."

Jul 1, 1936

By T. M. Klemetti, G. M. Molinda, D. M. Pappas

Some of the most difficult coal mine roof in the U.S. can be found in the Illinois Basin. Factors contributing to the high roof fall rate include: weak moisture-sensitive roof rock, high horizontal stress, and limited longwall mining. The depth of cover ranges from 90-1,000 ft and roof damage from horizontal stress can be severe. Moisture sensitive-roof rock is common above the Springfield-Harrisburg Herrin #5 and #6 seams in the Illinois Basin, and contributes to roof skin deterioration. The roof fall rate increases significantly in the humid summer months. The National Institute for Occupational Safety and Health (NIOSH) has shown, using lab and field studies, that highly moisture-sensitive roof rock can be directly correlated to poor roof conditions. Controlling the skin is the key to reducing rock fall injuries, and roof screening is, by far, the best remedy. Illinois Basin coal operators have been successful in reducing the number of rock fall injuries in recent years. NIOSH has documented best practices for screen installation which has resulted in safe, efficient operations. Other solutions to skin failure include: the use of denser five bolts per row patterns to reduce spans between bolts, systematic supplemental support in intersections, straps and large pans protecting operators, and air conditioning to remove moisture from the intake air.

By H. H. Dewing

The Bureau of Mines conducted a laboratory-scale investigation of a technique that produces zinc sulfate and elemental sulfur from sphalerite concentrates by reaction with sulfuric acid at 175° to 200° C and ambient pressure. The objective of the investigation was to develop a hydrometallurgical method of producing zinc from sulfide concentrates that does not generate sulfur dioxide pollutants. Reaction with 80-to 85-pct sulfuric acid produced 4 moles of sulfur for every 3 moles of sphalerite reacted, with minimal production of sulfur gases under optimum conditions. More than 98 pct of the zinc was recovered as zinc sulfate after 3 hours at 175° C. The reaction mixture was leached with simulated spent zinc electrolyte containing 13-pct sulfuric acid to recover zinc sulfate from the insoluble, high-sulfur residue. Neutral zinc sulfate, which is required for electrolysis, was separated from the sulfuric acid solution by crystallization as ZnS04?7H20 at -10° C. Up to 80 pct of the water in the recycled electrolysis solution was removed by the crystallization process; evaporation was used to further concentrate the sulfuric acid for reuse in leaching sphalerite. Advantages of the proposed method over conven-tional roasting and leaching include virtual elimination of sulfur dioxide, production of a solid sulfur byproduct, and higher zinc recoveries due to elimination of zinc ferrite losses.

Jan 1, 1978

By Richard J. Mainiero, Michael J. Sapko, Marcia L. Harris

Since 1988, there have been 17 documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through ground strata into occupied enclosed spaces as a result of proximate trench blasting or surface mine blasting. These incidents resulted in 39 suspected or medically verified carbon monoxide poisonings and one fatality. To better understand the factors contributing to this hazard, the National Institute for Occupational Safety and Health (NIOSH) carried out studies in a 12-foot diameter sphere to identify key factors that may enhance the levels of CO associated with the detonation of several commercial trenching explosives. The gaseous detonation products from emulsions, a watergel, and ANFO blasting agents as well as gelatin dynamite, TNT, and Pentolite boosters were measured in an argon atmosphere and compared with those for the same explosives detonated in air. Test variables included explosive formulation, wrapper, aluminum addition, oxygen balance, and density. Major contributing factors to CO production, under these laboratory test conditions, are presented. The main finding is the high CO production associated with the lack of afterburning in an oxygen poor atmosphere. Fumes measurements are compared with the manufacturer’s reported IME fume class and with the Federal Relative Toxicity Standard 30 CFR Part 15 in order to gain an understanding of the relative toxicity of some explosives used in trench blasting.

By Charles E. Munroe

On March 14, 1921, an explosion occurred at about 6:15 A.~. on the premises of an iron-mining concern throug:1 which two magazines, one containing upwards of 9,000 pounds ot a high explosive of the dynamite class, and a second, 60 feet distant, containing upwards of 10,000 No. 6 detonators, were completely destroyed, and a ncratertt,? f3et deep by 30 feet in diameter, was excavated in the gro~ at ~he place whare the mag~iine containing the high explosive had been lo~ated. As a rule any eye wit~esses to the circumstances im.~ediataly preceding and d(irectly concurrent with a.c.ci.:lental ex;losions ar.e victims of s11ch explosions, and, therefore, the conclusions reached as to the cauoa. of such explosions must, perf'orce, be based aln:ost completely on circumstantial evidetJ.ce. In this iii.stance, b:ecause both the explosive and detonators were of -orov{:;d: character; because of the time of the day and the state of operations iit the·· time of the e:.q,losion; because the rerroteness of the location of the n:-1agazi::1es 1 0::1 the side of a ravine, easily admittfi of unobserved approach; beca:iise differencas existed, and because no obvious cause was at once apparent, there arose suspicfon that the explosion was not accidental.

Sep 1, 1921

By T. H. Jeffers

Significant amounts of cobalt, a strategic and critical metal, are present in readily accessible spent copper leach solutions. For example, recovery of cobalt at two major u.S. copper operations could produce about 1,300,000 lb Co annually, about 13 pct of domestic consumption. However, techniques such as solvent extraction and precipitation have not proven cost effective in separating and recovering the cobalt from these low-grade domestic sources. The Bureau of Mines has devised a procedure using a chelating ion-exchange resin to extract cobalt from a pH 3.0 copper leach solution containing 30 mg/L Co. Cyclic tests in 4-ft-high by 1-in-diam columns gave an average cobalt extraction of 95 pct when 65 bed volumes of solu-tion were processed at a flow rate of 4 gpm/ft2 of resin area. After an impurity scrub, eluates contained, in grams per liter, 0.4 Co, 0.2 Ni, <0.001 Cu, 1.3 Fe, 2.8 Zn, and 0.008 AI. Solvent extraction procedures to remove impurities, reject nickel, and concentrate cobalt produced a cobalt sulfate solution containing 80 g/L Co, 0.05 g/L Ni, and not more than 1 mg/L Cu, Fe, Zn, or AI. Based on data from commercial electro-winning operations, this solution appears suitable for production of metallic cobalt.

Jan 1, 1985

By Terry J. Close

In 1992, as part of the U.S. Bureau of Mines Idaho Land Assessment Program, the Western Field Operations Center investigated the mineral resources of the 30,300-hectare Elk Summit study area. The area is in the Clearwater National Forest, adjoining the Selway-Bitterroot Wilderness in Idaho County. Idaho. The study area is underlain by granitic and metasedimentary rocks. Associated with these rocks are road metal (stone) resources, black sand mineral placer resources, and thermal water resources. Also present are abundant sand and gravel. Two of the five sites examined during the Bureau study have road metal (stone) resources, one has black sand mineral resources, one has thermal water resources. The fifth site is a black sand mineral placer occurrence. There is no evidence of petroleum or coal resources. Idaho County records indicate that 38 mining claims, mostly black-sand placer, have been located in the study area, Twenty-three of the claims are current. Workings consist of a few pits and trenches at the placer, and two borrow pits. The only mineral commodity produced from the area was about 1,500 tonnes of stone excavated from the Savage Pass and Swamp Creek borrow pits along the Elk Summit road, north of Hoodoo Lake. The stone was used to surface the road; these stone resources will continue to be used as needed.

Jan 1, 1993

The coal deposits in Alaska occur in several major coal fields or basins. The deposits underlie about a quarter of the state, an area larger than Montana. Approximately 60 percent of the coal is bituminous and 40 percent is subbituminous. Less than one percent is lignite or anthracite. Although known coal reserves are estimated at only 6.1 billion tons (about 1.25 percent of U.S. reserves), estimates place the hypothetical reserves at 5.5 trillion tons and the identified reserves at 170 billion tons. The differences are due to limited exploration programs within the state. Conditions affecting mining and reclamation are unique to Alaska because of its extreme northern latitude. For example, permafrost occurs in about 75 percent of the state; tundra vegetation occupies vast treeless regions; and the climate is characterized by extremely cold winter weather and a short summer season. In addition, hydrologic conditions are considerably different from those in other states; major streams fed by silt-laden glacial melt water contain greater concentrations of natural sediment than the effluent discharge limits permitted by federal regulations. Also, some coal field locations are subject to potentially high seismic risk. These factors make coal mining and reclamation in Alaska more difficult than in other states. Alaska&apos;s program to regulate surface coal mining was approved May 2,1983. The Abandoned Mine Lands program was approved December 23,1983.

Jan 1, 1992