Search Documents

By Raymond M. Stateham

Microseismic noise rates and slope movements were measured in an unstable area along the north wall of the Tripp-Veteran pit, Kennecott Copper Corp., Ruth, Nev. Low-noise, wide-band microseismic geophones were located at various points in the wall, and the change in distance across open fractures, resulting from instability, was determined by repeated measurements between fixed points set on each side of the fractures. The microseismic noise rate increased and decreased with corresponding increases and decreases in the rate at which the fractures opened. The microseismic noise rates and changes in width of the fractures show excellent agreement, and the two types of measurements complement each other in monitoring the progress of pit wall failure.

Jan 1, 1971

By Henry G. Dorsett

Dust explosion data obtained in laboratory tests by the Bureau of Mines are presented for 73 chemical compounds and mixtures, 29 drugs, 27 dyes, and 46 pesticides. Information is given on ignition temperatures of cloud and layer, minimum igniting energy, minimum explosive concentration, percent of inert dust required to prevent flame propagation, limiting oxygen concentration in the atmosphere to prevent ignition, and pressures and rates of pressure rise at dust concentrations of 0.1, 0.2, 0.5, 1.0, and 2.0 ounces per cubic foot. Explosibility indexes are computed where data are available to permit comparison of the relative explosion hazard. Variations of explosibility parameters with chemical composition are discussed. General means for minimizing the dust explosion hazard are reviewed.

Jan 1, 1968

By Wilbur I. Duvall

Nineteen quarry blasts were instrumented with particle-velocity gages mounted in a uniform soil overburden, back of one face in a quarry in Iowa. Three components of particle velocity, radial, vertical, and transverse, were recorded at each of eight stations back of each blast. Distances from blast area to gage stations ranged from 150 to 3,000 feet. Eleven of the quarry blasts employed millisecond delays, and eight were instantaneous blasts. Charge weight per hole was 200 pounds, and the charge weight per delay interval, including the instantaneous blasts, ranged from 100 to 3,000 pounds. Analysis of the data from these tests shows that the particle velocity, V, produced at distance, D, by a quarry blast of charge per delay interval, W, can be represented by an equation of the form, V=KWb D-n, where b and n are exponents, and K is the intercept constant which is a measure of the level of vibration. The value of K for a millisecond-delayed blast employing one hole per delay interval is about 42 percent larger than the value of K for a single-hole blast. The value of K for a multiple-hole milli-second-delayed blast is about the same as that for an instantaneous blast when the charge per delay for the millisecond blast is equal to the total charge for the instanteneous blast. The vibration level from millisecond-delayed blasts employing one hole per delay is shown to be independent of the length of the delay interval and the number of delay intervals over the range of the variables tested: 9, 17, and 34 milliseconds and 3, 7, and 15 delays per blast.

Jan 1, 1963

By Larry G. Stolarczyk

This report deals with the creation of an efficient method to determine if command, control, communication and monitoring (3cm) equipment in coal, metal and non-metal mines is susceptible to Radio Frequency Interference (RFI) from the Medium Frequency (MF) radio communications system. A qualitative and quantitative RFT test plan was developed for in-mine and laboratory evaluation of the equipment. The laboratory testing was accomplished using the TEM Test Chamber. Detailed information on the Test Plan and the TEM Test Chamber is included. During in-mine testing of the MF System some underground equipment malfunctioned when the transmitter's radiating antenna was in close proximity. Electromagnetic Compatibility (EMC) testing was done on three levels; Component (circuit or box), subsystems and system. Nine tables are included which show the results of testing various equipment for RFI.

Jan 5, 1986

By Forrest T. Moyer

Injury experience in the mineral mining and processing industries during 1968 was slightly improved in the nonfatal-injury record but worse in the fatality record. The resulting frequency rate of all injuries was slightly better, whereas the injury-severity rate retrogressed appreciably from the figure for 1967. Overall operating activity, as measured by man-hours of worktime, was slightly higher in 1968. However, there were several major segments of the mineral industries in which activity was lower owing to reduced demand for mineral products and to several major work stoppages. These statistics comprise the injury and work experience of all personnel engaged in production, exploration, development, maintenance, repair, and force-account construction work, including supervisory and technical personnel, and working partners and owners at mineral-producing and mineral-processing establishments in the United States. Data concerning officeworkers are excluded except for the oil and gas industry for which such information is not separable. All injury rates and totals are calculated from data before rounding. The data for 1968 are preliminary except for the anthracite, coke, petroleum and natural gas, native asphalt, peat, and slag industries, which are final. The figures represent full coverage for all industries except oil and gas for which coverage is not complete, particularly with respect to small companies.

Jan 1, 1970

By Frank E. Chase

Kettlebottoms are columnar masses of rock--the preserved casts of ancient tree stumps--embedded in coal mine roof strata (of which they are a part). Because unsupported kettlebottoms can detach from a mine roof without warning, they are a hazard to miners. The primary objectives of this investigation were (1) to better define and describe kettlebottoms and (2) to evaluate kettlebottom support techniques in terms of safety and effectiveness. A telephone survey of mine operators, interviews with Mine Safety and Health Administration (MSHA) personnel, and underground mine visits were conducted in Pennsylvania, West Virginia, and Kentucky. Information gathered during this investigation indicates that the size and frequency of kettlebottoms in mine roof are dependent upon past geologic events and biological processes active during the deposition of roof sediments. To ensure the safety of mine personnel, all undermined kettlebottoms should be supported. The roof should be bolted next to kettlebottoms less than 3 ft in diameter, close enough to allow a portion of a wood or steel header to be extended beneath each kettlebottom for support. Two bolts and a wood plank or steel strap should be employed to support kettlebottoms over 3 ft in diameter.

Jan 1, 1983

To rapidly limit and interrupt high dc fault currents with minimal arcing in the mine atmosphere. Approach Design a dc switching sys-tem which uses a pressurized, liquid metal-filled, change-of-state device combined with a conventional interrupter and commutating switch. Direct Current Interruption Switching and interruption of large direct currents imposes severe loads on fuses, contactors, and circuit breakers in mine power systems. This problem is much more pronounced with de than with ac because of the lack of a natural current zero in dc. Dc interruption is characterized by persistent arcing that can foul contact tips and con-tribute to interrupter failures. To reduce maintenance and prolong the service life of these units, a commercially viable dc switching system has been developed by the Bureau of Mines through a research contract with the University of Pittsburgh. This system rapidly limits and interrupts high fault currents when used in combination with conventional interrupters.

Jan 1, 1983

To reuse chromium, nickel, and molybdenum now lost in stainless and specialty steel-making wastes, and simultaneously to overcome the current environmental problem resulting from landfilling these wastes. Approach A variety of stainless and specialty steelmaking wastes are agglomerated and recharged into the plant's electric arc furnaces. How It Works Stainless and specialty steel-making wastes such as bag-house dust from the electric arc furnace, dust from the argon-oxygen decarburization unit, grinding swart, and mill scale are blended in proportion to the ratio in which they are generated. Next they are agglomerated on a pelletizer with an addition of a small amount of carbonaceous reducing agent, and air-dried in preparation for being recharged into the furnace. Some mixtures of wastes tested in the laboratory required the addition of binders and/or the use of ovens in lieu of air-drying to produce sufficient pellet strength. Although the optimal maximum particle size of wastes being pelletized is 35 mesh, somewhat larger particle sizes were satisfactorily pelletized during in-plant tests. The photograph shows a typical mixture of wastes and the pellets made from them.

Jan 1, 1981

By R. L. Grayson, W. E. Wallace, J. W. Stephens, M. D. Attfield, P. S. Brower, V. Vallyathan, M. J. Keane, J. C. Harrison

Pure respirable quartz is a known pathogenic agent for lung disease. However, for mixed dusts, neither mineralogical nor in vitro cytotoxicity assays unequivocally predict the contribution of quartz to their pathogenic potential.First, although Coal Workers' Pneumoconiosis (CWP) and Progressive Massive Fibrosis (PMF) prevalence have been found to correlate with total respirable coal mine dust exposure, and with coal rank (Attfield and Morring, 1992), epidemiological studies generally have not found the quartz component of coal mine dust as measured by X-ray diffraction or infrared spectroscopy (each of which essentially measures the mass-percent quartz in a bulk sample) to be clear predictors of CWP prevalence or incidence (Walton et al., 1971). Second, the properties which distinguish the extreme fibrogenic potential of quartz are not revealed by conventional in vitro bioassay comparison with other silicate mineral dusts. As an example, quartz and kaolin (aluminosilicate) clay in vitro cytotoxicities are comparable for lavaged primary pulmonary macrophages.The studies discussed here address these two anomalies from a general hypothesis that the pathogenic activity of respired quartz particles is associated with properties of, and interactions with, the particle surfaces. One factor in the expression of toxic activity by a particle surface is the biological availability of that surface. Anomalous lack of correlation of disease prevalence with mass percent quartz in exposures to some mixed composition respirable-sized dusts suggests that individual particle surface features, invisible by bulk sample mass analysis, may alter the biological availability of a fraction of quartz particles in a dust. For pure-surfaced mineral particles, the comparably strong prompt membranolytic activities of quartz and kaolin in vitro suggest that upon deposition of such particles in the lung there must be other interactions with particle surfaces which distinguish quartz. This might be due to toxic surface-associated sites specific to silica, or to interactions of other sites on other mineral particles which affect the biological availability of their toxic functional groups. For example, alurninol groups on clays affect the availability or activity of adjacent silanol groups. Surface activities which distinguish quartz pathogenici ty might be manifest in one or more of the sequential interactions upon deposition in the lung; first with the pulmonary surfactant system, then with extracellular and phagolysosomal enzymatic digestive processes, or with subsequent cytotoxic processes.

Dec 1, 1995

By J. F. McIlwain

The Bureau of Mines investigated fumes generated by selected welding materials used in mines in order to help determine their relative hazard potential. The initial phases of the study have been completed. A welding-fume generation and collection apparatus was designed, assembled, and calibrated. Five brands of coated, AWS-type E308-16 stainless steel electrodes were tested. Total fume generation rates of 0.39 to 0.51 g/min were measured. Quantitative chemical analyses were conducted for all of the principal firms constituents. Two analytical schemes were used to determine levels of the Cr6+ and Cr3+ species contained in the welding fumes; comparable results were obtained. The Cr6+ was found to be the most hazardous constituent, leading to a maximum allowable total fume exposure of 1 mg/m3. Fume generation rates and fume constituent analyses will be derived for other groups of welding electrodes using similar procedures.

Jan 1, 1983

By Benjamin Petkof

Production quarry blasts in three rock types were photographed with a high-speed camera. Analysis of the films showed that step increases sometimes occur in the horizontal velocity of the broken rock. These step velocity increases were observed only in the first foot or so of rock movement. This observation indicates that the gaseous products of the explosion do additional work on the rock after it is crushed and cracked by the initial compressive-stress pulse and the reflected tensile-stress pulse. The observed initial fly-rock velocity is compared with the calculated fly-rock velocity for reflection spalling. A mechanism possibly causing the velocity increases is discussed. INTRODUCTION When a small concentrated charge of explosive is detonated at the bottom of a drill hole near a free surface, two modes of rock failure have been observed; both are associated with the stress pulse generated in the rock by the detonating explosive. The first mode of failure is the crushing and radial tensile cracking associated with the initial passage of the compressive-stress pulse as it propagates outward from the explosion. This type of rock failure is usually confined to the immediate vicinity of the charge hole. The second mode of failure is the tangential and radial tensile cracking associated with the tensile-stress pulse that is reflected from the free surface. This mode of failure is commonly called scabbing or spalling and has been shown to be a primary cause of rock failure in crater formation at one free surface. (3).4

Jan 1, 1961

By J. M. Stuve

Low-temperature adiabatic heat-capacity determinations were made by the Bureau of Mines in the temperature range from 5 to 300 K for the two crystalline modifications of zinc sulfide, sphalerite (ß) and wurtzite (a). The entropy at 298.15 K of sphalerite was evaluated as l4.02±0.04 cal/deg mole and wurtzite, l4.06±0.04 cal/deg mole.

Jan 1, 1974

By Kenneth O. Bennington

This investigation is part of the Bureau of Mines research effort directed at advancing mineral technology and minimizing energy requirements for extractive metallurgy. The emplacement of the primary minerals petalite (LiAlSi4010) and spodumene (LiAlSi206) in the lithium pegmatites is examined on the basis of their Gibbs energies of formation determined from lithium metastltcate and oxides, using a series of proposed reactions. The reaction between spodumene, quartz, and petalite (LiAlSi206 + 25i02 [=] LiAlSi4010) apparently does not take place in nature but may be proved experimentally.

Jan 1, 1982

By Robert P. Vinson, Fred N. Kissell, Edward D. Thimons

Because of the high number of accidental methane gas ignitions in metal and nonmetal mines, the Bureau of Mines searched for a simple guideline that would allow mine personnel to evaluate the methane hazard in a given mine. Air samples were collected by the Bureau in 53 metal and nonmetal mines and analyzed for trace evidence of methane gas. Samples were collected in the returns and at the working faces. Those mines classified as gassy by the Mine Safety and Health Administration had a significantly higher average methane concentration than those classified as nongassy. Of the 9 gassy mines sampled, 7 had methane concentrations above 100 ppm, whereas only 1 of the 44 nongassy mines had a concentration above 100 ppm. The 100-ppm concentration may be used as a simple and convenient guideline for forecasting the methane hazard in a mine, whether or not the mine is classified as gassy. There was no consistent correlation between commodity mined and methane concentration, nor was there a correlation between mine depth and methane concentration. Neither of these factors can be considered a guideline for predicting methane hazards.

Jan 1, 1979

By D. H. Chambers

The Bureau of Mines developed a process for producing high-purity zinc and tin by electrorefining from liquid amalgams. Commercial grade metals were dissolved in mercury to produce saturated amalgams at room temperature. Amalgams were also prepared by electrolytic transfer from soluble anodes of the metals to a mercury cathode. Amalgams formed by both methods were used as anodes in electrorefining cells to produce high-purity cathodes. Metal impurities, excluding mercury, were at levels of less than 5 ppm in zinc and 9 ppm in tin. Mercury content was about 2 to 10 ppm in zinc products, and this was effectively removed by heating the cathodes in a vacuum. Mercury was excluded from tin cathodes by pumping the tin electrolyte through tin turnings and controlling the cell temperature.

Jan 1, 1969

Minimize failures or inefficiency in the operation of in situ mining wells. Approach The proper design, construction and development of wells are important to any in situ leaching operation. To permit cost-effective production from an underground ore body by leaching it in place, many wells are normally installed. Construction and maintenance costs increase with the number of wells, and poor construction and maintenance procedures result in production losses and negative environmental impacts, To minimize these losses and impacts, the Bureau of Mines conducted an investigation to determine the optimum in situ well construction and operating procedures for the minerals industry. Factors considered during the investigation included drilling equipment and procedures; types of well casing and grouting; completion methods, e.g, screening or perforation; and system maintenance. The data collected were used to prepare a manual that offers guidelines

Jan 1, 1984

To restore ventilation and prevent the accumulation of explosive or toxic gases by quickly installing substitutes for stoppings blown down by an explosion. Approach Temporarily replace blown down stoppings with a parachute-shaped brattice which can be erected in minutes. How It Works The self-sealing brattice is secured to the roof, ribs and floor by anchoring its nylon edge strip at several points using extensible poles, shads, or available projections such as roof bolts. The air pressure in the entry pops open the chute of lightweight sailcloth, forcing it tightly against floor, roof and rib. See Figure 1. This emergency brattice has been tested at two locations in the Bureau's Experimental Mine at Bruceton, Pennsylvania. In a test last December, one MESA inspector wearing full rescue apparel (including self contained breathing apparatus) installed a self sealing brattice in an entry at the Bruceton Mine. Although he did not have any previous experience with the device, he easily erected it in slightly less than 10 minutes, using two extensible supports (pogo sticks). Research to improve and refine the self-sealing brattice is continuing.

Jan 1, 1977

Reduce the costs associated with conventional treatment of acid mine water. Approach Conventional treatment of acid mine drainage consists of plants requiring large mixing and aeration tanks, mechanical aerators and large, shallow settling ponds. Such plants are usually very costly to construct, maintain and operate. The Bureau of Mines has developed a simple, low-maintenance, highly efficient system to treat acid mine drainage which mixes, aerates, and neutralizes mine water Simultaneously in the existing discharge pipeline by using the pressure generated by the deep mine discharge pumps. The mixing and aeration action of the in-line system significantly increases oxidation rates of ferrous iron. Iron and manganese are removed, even at near neutral pH levels, due to the high efficiency of this system. How It Works The In-line Aeration and Treatment System (ILS) consists of two commercially available components, a jet pump (ejector) and a static mixer. The jet pump is simply a nozzle that converts water, already under pressure, into a high-velocity stream that entrains air by Venturi action. If neutralization is required, sodium hydroxide or lime is added along with the air at the Venturi opening. The aerated and neutralized water then enters the static mixer, which is a length of internally spiralled pipe that mixes air and water together. The two components, which are both about 8 feet in length, replace the last section of discharge pipe at a point before the mine water is emptied into a pond. Along with the settling pond, these components treat the water so that it meets discharge criteria. The system has been used at surface drainage treatment facilities as well, but in such use a pump is required to provide the necessary pressure drop across the Venturi opening.

Jan 1, 1985

By Thomas H. Dubaniewicz

Thirteen miners died as a result of 2 explosions in the Jim Walter Resources No. 5 mine near Brookwood AL in September 2001. Both explosions were ignited in intake air entries, and both were probably ignited by electrical equipment. With few exceptions, permissible equipment is not required in intake air entries of US underground coal mines Researchers with the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory. studied the electrical equipment ignition sources for the Brookwood and other w disasters to develop recommendations for preventing similar disasters Adherence to National Electrical code® requirements for flexible cords installed in hazardous (classified) locations may have prevented the second massive Brookwood explosion. The 30 CFR Part 7 requirements for battery assemblies should be reevaluated, taking into consideration United Mine Workers of America recommendations and the Zone 1"increased safety" standard requirements for battery assemblies, Class 1 Division 2 or Zone 2 explosion protection techniques are recommended for intake air equipment so that they do not present a methane air ignition source under normal operation before mine power is shut down during emergencies Battery powered circuits intake air that are likely to remain energized during emergencies should be protected by more stringent protection techniques, to protect rescue/recovery personnel. Index Terms -Class 1 hazardous location, mine explosion, flexible cord, battery assembly, permissible equipment

By R. Barany

The heat of formation at 298.15 ° K of muscovite was determined by solution calorimetry . The value obtained for the heat of formation from the elements was -1,421.2 ± 1.3 kcal / mole , and the value for the heat of formation from the oxides was -55.9 ± 1.3 kcal /mole .

Jan 1, 1964