Search Documents

By J. R. Wait, D. A. Hill

A survey of the literature on ELF and VLF atmospheric noise has been made. Most measurements have concentrated on the vertical electric field and the horizontal magnetic field rather than the vertical magnetic field which is of interest in transmission between horizontal loops. The limited vertical magnetic field data indicates that the vertical component is generally 10 to 20 dB below the horizontal component. Three laterally inhomogeneous earth models have been analyzed for conversion of horizontal to vertical magnetic field. The rough surface model examines surface effects, the inhomogeneous thin sheet model treats volume effects, and the buried cylinder model treats localized man-made effects. All three models predict the possibility of significant conversion from horizontal to vertical magnetic field. A thin sheet model has also been used to examine transmission from a buried magnetic dipole source. It is found that the pre- dicted fields more nearly model the measured data than does the homogeneous half-space model.

By Gerrit V. R. Goodman, Charles D. Taylor, Edward D. Thimons, Jay F. Colinet

The importance of controlling respirable dust and methane gas levels in underground coal mining cannot be underestimated. While respirable dust can significantly affect the occupational health of underground coal miners, methane gas accumulations pose significant safety concerns for these same workers. Water sprays and machine mounted dust scrubbers offer effective control of respirable dust exposures and methane gas accumulations. Water must not only be applied carefully to avoid dust rollback to the machine operator but must create sufficient turbulence to remove dead zones that could contain high concentrations of methane gas. While the flooded-bed dust scrubber has been generally responsible for decreased worker exposures to respirable dusts, this device has proved effective in controlling methane levels at the face. This paper reviews practical applications of water sprays and dust scrubbers to control respirable dust and methane gas on continuous miner faces.

Jan 4, 2000

Provide room-and-pillar operators with practical in- formation and guidelines concerning multiple-seam mine design to reduce ground problems associated with the interaction of adjacent working.

Jan 1, 1994

By Carl E. Norman

An investigation of geologic structure on macroscopic, mesoscopic, and microscopic scales was conducted on near-surface igneous and metamorphic rocks in which the existing stress field was determined by in situ methods. A consistent NE-SW orientation of the maximum compressive stress in the horizontal plane at four of five test localities appears due to the intrusion of NW-trending diabase dikes. Structural features at the mesoscopic scale show no consistent directional relationship to determined stress directions. Petrofabric diagrams of open microfractures show preferred orientations, but these are not consistently related to the orientations of larger structural features, such as joints, foliation, or mineralized shear zones. However, at five of six test sites the preferred direction of microfractures occurs nearly perpendicular to the maximum principal stress directions; an anomalous parallel relationship exists at a test site in an intrusive rock body. The results suggest that the open microfracture subfabric may provide a means for gaining information on the directional properties of stress fields. Such information can be obtained from oriented cores taken from holes which exceed the approximate 100-foot depth to which other in situ methods are presently limited.

Jan 1, 1970

By W. H. Eddy

The Bureau of Mines conducted laboratory batch-and small-scale continuous flotation processing tests on waste granite fines from Georgia, to determine the feasibility of recovering usable feldspar and quartz products by flotation. Two flotation methods were utilized for the removal of biotite and other iron-bearing minerals: One was in an acid-cationic circuit, and the other in an alkaline-anionic-cationic circuit. Feldspar was recovered using an acid-cationic method. To produce commercial-grade feldspar and quartz products it was necessary to employ either two sequential froth flotation circuits or one froth flotation circuit supplemented by wet-magnetic separation techniques to remove iron contaminants. Continuous flotation processing yielded a commercial-grade feldspar concentrate containing, in percent, 3.8 Na20, 5.4 K20, and 1.10 CaO, with recoveries of 77.8, 70.3, and 64.4, respectively. The feldspar tailing was high-quality glass sand containing 98.2 percent SiO2 and 0.024 percent Fe2O3. About 42 percent of the quartz was recovered at glass sand specifications. An effective separation of, potash feldspar from the bulk feldspar concentrate was achieved by batch flotation in a mineral separation cell.

Jan 1, 1974

By Jeffrey Kohler, John J. Samrnarco, Thomas Novak, Lloyd Morley

Equipment control functions that were once hardwired are being implemented with software and very large scale integrated (VLSI) devices. Often this transition has resulted in increased flexibility, improved quality, and decreased costs. At the same time, it has created new concerns and challenges concerning worker safety. The visible and well-defined ladder diagram for relay-logic has been replaced by program in which the exact outcome for varied inputs can be more obscure. In the coal mining industry,-efforts to automate longwall mining systems hove resulted in semiautonomous machines operating within the same space as workers This paper describes an effort initiated by the National Institute for Occupational Safety and Health (NIOSH to identify the safety rules related to the use of processor-controlled equipment in mining. Specific findings in the areas of human factors, hardware, and some safety are presented in this paper, and a brief description of a plan to address identified weaknesses is given.

By Charles Vaught

This paper discusses the fact that US coal mining organisations are losing the knowledge they need in order to be able to respond to emergencies. The authors note that knowledge management provides a useful perspective from which to view the problem, but that the debate about what constitutes knowledge should be broadened to include a debate about what constitutes management. It is argued here that knowledge is actually shared knowing distributed across group members; that such knowledge can be managed by cultivating it; and that narrative is the medium through which this may be done. The paper then examines NIOSH research that has attempted to use such an alternative knowledge management approach to help potential mine emergency responders better deal with the predicaments they are likely to encounter on-site.

Jan 1, 2006

By J. Walden, S. Rhoades, R. E. Miller, R. Gibbs, P. Boman

Accelerometers and pressure transducers mounted in suspension components can be used to monitor the ride of haulage trucks. Presently, it is difficult to tell what caused a jolt to the truck using either pressure or acceleration data alone. When information horn a Global Positioning System is recorded at the same time as shock pressures or acceleration data, then the exact location of an event can be determined. Mine management can then determine what caused the jolt to the truck.

By Dean H. Ambrose

This paper presents a technique for representing and analyzing random motions and hazardous events in a computer simulated three-dimensional workplace, providing machine designers and safety analysts with a new technique to evaluate ways to reduce operator-machine interaction hazards. Technical data in this paper is based upon a project striving to reduce workers' risks from being hit by underground mining machinery in a confined space. By simulating motions of an operator's random behavior and a machine's appendage, researchers can accurately identify hazards, and use that information to form safe designs for mining equipment appendage velocity. Validating the model provided improvements in the operator's optimal viewing area, work task- starting positions, and operator's motions for a more accurate random behavior. Preliminary simulation results provided (1) an interesting approach to research data gathering in that there was no need for live subjects and test sites and costs associated with experiments become insignificant and (2) that the model was versatile by showing it was capable of accurately mimicking the range collision forces versus speed, operators' size, and risk behaviors found in actual industrial situations and showed (I) that response time significantly affects the number of collisions experienced by the virtual subject and (2) that analysts must be discerning with the model and not read more From the databases than what the simulation model was designed to deliver. Keywords: random human-motion, anthropomebics model, machine-operator hazards, mine safety

By Wing G. Agnew, John A. Johnson

"INTRODUCTION This paper is one of a series being published by the Bureau of Mines pertaining to an investigation on the use of stemming in metal mines now being conducted at the Mount Weather Testing Adit. Its purpose is to compare the amount of dust and gases produced as a result of blasting charges of dynamite (1) in drill holes, (2) in bombs, and (3) in mud-cap or adobe shots.ACKNOWLEDGMENTSValuable assistance and advice on stemming were given by members of the staff at the Bureau of Mines, as acknowledged in previous publications. 4/TEST PROCEDUREThe results used for comparison in this report are from dust and gas samples taken after blasting (1) four regular test rounds with no stemming, (2) five bomb shots, and (3) two mud-cap or adobe shots."

Dec 1, 1942

By John W. Adams

The present status of the National Bureau of Standards program is that many magnetic tapes of analog data have been recorded in four major mines. Each mine uses different types of equipment. In addition, some surface measurements of noise have been made at two additional mines. Two types of recordings have been made: (1) broadband measurements for spectral plots and (2) narrowband measurements for amplitude probability density (APD) plots. Only data from one mine (Robena #4) has been processed and was, presented at this workshop. The short-term goals are: (1) finish processing data from the other mines, (2) establish or reduce measurement system uncertainties, (3) put Robella report into final form for distribution, and (4) hold a review to determine what has been done, to distribute and to interpret the preliminary data, and to determine what still needs to be done. Long-term goals are: (1) complete final reports on each of the mine trips, (2) establish techniques for predicting noise in mines already visited and establish uncertainty bounds for these predictions, and (3) establish techniques for predicting noise in mines that have not been visited (but that use similar equipment to those visited) and also establish uncertainty bounds for these predictions. Specific factors or formats to be presented include: (A) For underground broadband measurements: 1. 300 Hz to 100 kHz spectral plots 2. 300 Hz to 384 kHz spectral plots 3. 300 Hz to 192 kHz spectral plots 4. 300 Hz to 6kHz (subject to change to 3 or 12 kHz) spectral plots (B) For surface broadband measurements: 1. 300 Hz to 6 kHz (or 12 kHz) spectral plots 2. 300 Hz to 3 kHz spectral plots (C) For underground narrowband measurements : 1. APD plots at 12 frequencies from 10 kHz to 32 mHz of magnetic field strength 2. R. M.S. and average values will be calculated based on time averaging for these plots (D) Sample spectral measurements of: 1. Roof-bolt voltages 2. Trolley wire-to-rail voltages 3. Phone line currents

Jan 1, 1973

By Edward F. Divers

A new nonclogging water spray system for continuous-mining machines has been developed under contract with the Bureau of Mines. This paper presents installation and operating guidelines for the system, which consists of improved and easily maintained machine-mounted hardware, including an inline Y-strainer, a hydrocyclone, a backup filter, and two quick-opening valves for flushing particulates from the strainer and hydrocyclone. Underground tests with continuous-mining machines have shown that when properly installed and maintained, the new sys tern virtually eliminates nozzle clogging and thus greatly reduces spray maintenance. The sys tern is relatively inexpensive and has been installed on typical continuous-mining machines for a total cost under $1,000.

Jan 1, 1976

By Jr. Hardy, H. Warren Shen

"A study is presently underway by the authors to investigate the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. An important aspect of this on-going project is the development of acoustic emission (AE) criteria which would make it possible to carry out remote monitoring of coal cutting operations. The on-going AE studies are fundamental in form and were undertaken to evaluate the general feasibility of AE monitoring techniques using simplified coal breakage and cutting procedures. The present paper will focus on the test facilities, experimental techniques, and results associated with linear, single-bit cutting. An AE-transducer, attached directly to the bit, detected AE signals during the cutting process.Experiments have been carried out on seven specimens of coal obtained from the USBM experimental mine at Bruceton, Pennsylvania. Three separate cuts were made for each of two bit angles (10 and 45 degrees) and two bit velocities (0.085 and 0.169 cm/sec), for a total of 12 separate cuts. Data associated with resulting particle size distribution and AE characteristics (major dominant frequency components) will be discussed. Data analysis has also been underway using a computer-based pattern recognition system known as ICEPAK (Intelligent Classifier Engineering Package). This program is able to evaluate over 100 features of an AE event and to make objective comparisons between AE signals associated with different loading or cutting parameters. The results to date show that AE generated during some of the test conditions can be recognized by ICEPAK with a recognition rate of 90% and higher while other conditions cannot at present be separated with a suitable recognition rate. Further analysis of the experimental data is presently underway.The reduction of the severity, and eventual elimination, of Coal Workers' Pneumoconiosis (CWP) depends on gaining fundamental understanding in a number of major areas. These include dust generation and entrainment, transportation, suppression, medical effects of dust, and possible treatment. At present a project is underway by the authors to investigate the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. An important aspect of this on-going project is the development of acoustic emission (AE) criteria which would make it possible to carry out remote monitoring of coal cutting operations. Suitable on-line analysis of monitored AE data would allow engineers to evaluate factors such as shearer bit conditions and cutting efficiency, and to quantify the particle size and shape distribution of the generateddust. The on-going AE studies are fundamental in form and were undertaken to evaluate the general feasibility of AE monitoring techniques using simplified coal cutting procedures. To date experiments have been carried out on coal under uniaxial compression, linear single-bit cutting, and cutting using a laboratory-scale, single-bit shearer. A brief outline of the overall study has been presented in an earlier paper (Hardy, Shen and Kimble, 1995). This paper will consider the linear single-bit cutting studies in more detail.It is generally accepted today that most solids emit low-level seismic signals when they are stressed or deformed. In this paper this phenomenon will be referred to as acoustic emission (Hardy 1972, 1981, 1989). In essence, the measurement of AE activity in a field or laboratory structure is relatively simple. A suitable transducer is attached to the structure, the output of the transducer is connected to an associated monitoring system, and the AE signals occurring in the structure, due to internal or external stress, deformation, and failure are suitably acquired, pre¬processed and recorded."

Jan 1, 1998

By T. T. Campbell

Research conducted by the Bureau of Mines demonstrated the feasibility of preparing columbium and tantalum metals by the application of Kroll-process techniques. Yields in excess of 95 percent were obtained in a modified Kroll-process reduction apparatus constructed from nickel and Inconel.4 Operating conditions during reduction and distillation were determined. Optimum temperatures during sodium reductions ranged from 650° to 750° C and for magnesium from 700° to 800° C with retort pressures ranging from 3 to 7 psig. Undesirable vapor phase reactions occurred when temperatures exceeded 750° C during sodium reductions or 850° C with magnesium. Vacuum distillation at 850° C effectively removed volatile salts and excess reductant from the reduced metals. Calculations based on the results obtained in small scale tests indicate that reaction rates of up to 34 lb/hr could be obtained during columbium reductions and up to 60 lb/hr during tantalum reductions in production scale reac¬tors. The small, laboratory-scale techniques used in this study could be adapted to commercial practice. The reduced powder or sponge metals can be consolidated by conventional arc-melting techniques, and the arc-melted metals can be fabricated into ductile sheet at room temperature. Analyses of arc-melted buttons prepared from Kroll-process tantalum or columbium showed that tantalum of greater than 99.8-percent purity was obtained and that columbium purity exceeded 99.7 percent. A significant purification of the reduced metals occurred when they were consolidated by electron-beam melting, and the purity and ductility of electron-beam-melted Kroll-process tantalum and columbium compared favorably with the commercial metals. After electron-beam melting, the purity of the tantalum exceeded 99.95 percent, and columbium purity was approximately 99.9 percent.

Jan 1, 1962

By D. J. Bauer

Solvent extraction techniques were used to determine the extraction sequence of yttrium and the rare-earth elements in an amine solvent extraction system. Single-stage extraction with Primene 81-R resulted in separation factors of 3.8 between yttrium and dysprosium and 25 between yttrium and cerium. Yttrium was concentrated in the aqueous phase. EDTA and DTPA, as aqueous phase counterextractants, enhance separation factors in mine-rare-earth sulfate systems. Yttrium separation from heavy rare-earth elements exhibits marked sensitivity to the position of yttrium in the selectivity scale of the rare-earth elements with the sequestrants. Yttrium-ytterbium separation is more effective with EDTA, whereas yttrium-dysprosium separation is more effectively increased with DTPA.

Jan 1, 1963

By R. E. Mussler

As part of an overall goal to develop technology that can maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines is evaluating a method for selectively extracting nickel and cobalt from low-grade domestic laterites. The method involves electrowinning to recover the metals in pure form; therefore, preliminary laboratory-scale electrowinning tests were conducted in both a nondiaphragm and a diaphragm cell to determine the effect of variables on energy efficiency under controlled conditions. Electrolytes were generally reagent-grade sulfate solutions that were prepared to simulate electrolyte that could be obtained by stripping nickel-and cobalt-rich solvent extraction reagents. Limited tests were conducted with electrolyte generated from laterite leach solutions. Electrical energy consumption in a nondiaphragm cell was 2.06 kwhr/lb Ni with the cell operated at 50° C, a cell feed of 90 g/l Ni, a pH of 3.5, an extraction of 3.2 g/l, and a cathode current density of 20 amp/ft2. The energy requirement decreased with increasing concentration and temperature, and increased with increasing. extraction and current density. At 50° C, energy consumption in the nondiaphragm cell was 21 pct greater than in the diaphragm cell, but it was only 5 pet greater at 65° C. For this reason and because of overall cost considerations, operation at 65° C with the nondiaphragm cell was preferred. Smooth sheets of cobalt were obtained by electrowinning in a nondiaphragm cell at selected temperatures from 50° to 85° C and with cobalt concentrations from 55 to 87 g/l. The energy consumption (1.48 kwhr/lb) was 22 pet lower with a cobalt concentration of 75 g/l and a cell temperature of 65° C than with a cobalt concentration of 55 g/l and a cell temperature of 50° C.

Jan 1, 1981

By Donald P. Blasko

The Bureau of Mines investigated two areas of the Alaska Peninsula (Iniskin Peninsula and Becharof Lake) where oil and gas seeps were known to occur in an attempt to determine (1) whether the seeps are still active and (2) the amount of bitumen contained in the drainage leaving the seeps. The oil, water, oil-water, and gas were sampled and analyzed. Five oil samples were taken at four separate oil seeps. The API gravity of the oil ranged from 8.90 to 21.4° and the sulfur content was from 0.12 percent to 0.59 percent. Four of the seven gas samples obtained revealed fair high caloric values, ranging from 746 to 924 Btu/cu ft, and averaging 844 Btu/cu ft. A total of 44 water samples were obtained. Bitumen content of the water was as high as 9,773 mg/l at one seep, but averaged less than I mg/l where the seep-drainage water entered the Gulf of Alaska.

Jan 1, 1976

By Raymond P. Maloney

The Rhyolite mercury prospect is on the south flank of Juninggulra Mountain--a large rhyolite intrusive in the Kuskokwim River region about 36 airline miles northwest of Red Devil, Alaska. Bulldozer trenching by the Bureau of Mines exposed bedrock at intervals in a 2,000-by 3,000-foot area where previous prospecting by the owners had disclosed abundant float and several in-place stringers containing cinnabar in widely varying amounts. The additional trenching indicated that the mercury mineralization in the limited area investigated was confined to erratically distributed short stringers and to small lenses, occurring in discontinuous zones in numerous silica-carbonate dikes and sills or along their altered contacts with sedimentary rocks. The geologic relationship of the mercury-bearing silica-carbonate dikes and the nearby rhyolite intrusive is similar to that existing at several other mercury mines and prospects in the. Kuskokwim region. The depth of over-burden and the presence of permafrost were serious obstacles to bulldozer trenching, and only a comparatively small part of the mineralized area was thus investigated.

Jan 1, 1962

By Richard G. Burdick

This Bureau of Hines report describes an interface between a minicomputer and peripheral device, The logic used to develop the device is discussed briefly, after which the device is described in detail; complete construction and operational details are given. The report should aid both in duplicating this device and in designing similar devices for different uses.

Jan 1, 1975

By Ted C. Briggs

The Bureau of Mines is evaluating the thermodynamic properties of helium and helium-containing mixtures. Twenty-two compressibility runs were made with helium at 0° C and pressures to 800 atmospheres using a Burnett-type apparatus. Data from the 22 runs were treated simultaneously and as separate runs while different functional forms and weighting factors were used. A fourth-degree-polynomial equation in the pressure gives a statistically satisfactory representation of the compressibility factor when the data are treated simultaneously and a weighting factor of Pr-3/4 is used. The second virial coefficient of helium at 0° C from this investigation is 11.997±0.015 cm3 mole-1. The stated uncertainty is the random error standard deviation. Compressibility factors determined by this investigation are precise to better than 0.01 percent and are believed to be accurate to better than 0.02 percent.

Jan 1, 1969