Search Documents

By Wm. C. Dean

The location of trapped miners from their seismic signals will be in- accurate if we assume the P-wave propagation velocity is a constant. P- wave velocities are anything but constant in regions about mines, so some calibration is necessary to obtain more accurate seismic locations. The reference event method compares the time arrivals of signals generated by the miners with those previously recorded from a reference or calibration event in the vicinity of the miners. This method locates the miners' position relative to the calibration source. Hence, the location of the miners is absolute if the reference event position is known absolutely, usually from surveys and mine maps. Advantages resulting from the system, besides greater accuracy, are locations independent of the velocity model assumed, the same solution from the full array and from any subset of four or more seismometers in the array (three if the miners' depth is known), fewer seismometers required, and no complex computers required for analysis. VELA Uniform experience shows that the accuracy of locations of teleseismic explosions and earthquakes is improved by an order of magnitude over locations computed from average travel time curves. Each calibration event is applicable only over a limited range. We recommend a field test of the method at a mine to measure its location accuracy, the range of effectiveness for each calibration event, the number of seismometers needed, and the number of reference events required per mine. From these experiments we could decide whether the reference event method was useful and, if so, what form a practical rescue system would take.

Jan 1, 1974

By Charles L. Kimbell

Available statistics on 1989 worldwide consumption of selected nonfuel minerals shown in table 5 show increases for 11 of 14 listed nonfuel mineral commodities with 1 unchanged from the 1988 level, a departure from the pattern of the past 2 years, in which each of the listed commodities registered gains. The 1989 results, however, were better than those for 1986 when only seven listed nonfuel mineral commodities recorded gains with one un- changed from 1985. Consumption of the two ferrous metal raw materials listed advanced as functions of increased output of pig iron and crude steel. The increase in iron ore consumption exceeded the increase in iron ore output, suggesting a slight drawdown of world iron ore inventories. The estimated in- crease in iron and steel scrap consumption was slightly greater than the minuscule increase in world steel production, but it is believed that there was little change in the ratio of iron ore to scrap in steel plant feed on a global basis.

Jan 1, 1992

Apply state-of-the-art monitoring and computer systems technology to remotely monitor geostructural data and evaluate ground conditions in near real-time. Background Recently, the coal mining industry has progressed dramatically from a labor-intensive industry to highly mechanized and automated systems achieving significantly higher production rates. In underground longwall coal mines, production and face advance rates have increased by almost tenfold in the last 15 to 20 years. With increasingly high advance rates, geologic anomalies which affect rock mass quality are encountered more frequently, far exceeding the current rate at which ground control information can be processed and analyzed. As a result, mine operators find themselves with insufficient time or resources to cope with the rapidly changing ground conditions. To keep up with the technological advancement in mining and the associated ground control problems, the Bureau of Mines is conducting a multi-phase research pro¬gram to implement a computer-assisted Ground Control Management System (GCMS). Research is ongoing at present, but when completed the system will be designed to 1) monitor and evaluate data on rock properties, geologic conditions, and rock mechanics data from underground sensors in near real-time; 2) interpret the analyses to evaluate the interaction between various critical ground control parameters; 3) assess the structural integrity of the mine; and 4) determine failure modes and provide recommendations for control measures, design modifica¬tions, and alternative support procedures. The system will be expanded into its full capability during various phases of this research program.

Jan 1, 1991

"The Generic Mineral Technology Center on Respirable Dust was established in August 1983, at the request of the Bureau of Mines, to conduct research that affords ""...each miner the opportunity to work underground during the period of (his/her) adult working life without incurring any disability from pneumoconiosis or any other occupational disease"". The Center consists of the Mining and Mineral Resources Research Institutes (MRI) of The Pennsylvania State University (PSU) and West Virginia University (WVU) in association with the MRIs of the Massachusetts Institute of Technology (MIT) and the University of Minnesota (UMN). (FIGURE 34) Michigan Technological University (MTU) is also affiliated with the Center in the area of diesel particulates.The Center brings together experts concerned with particles causing potentially disabling or fatal diseases including pneumoconiosis (""black-lung""), silicosis, and asbestosis. The latter is of deep concern not just to workers in the mineral sector of the economy but also to the general populace. The primary goal of the Center is to reduce the incidence and severity of respirable dust disease through advancing fundamental understanding of all aspects of respirable dust associated with mining and milling, and the interaction of dust and lungs. The research program of the Generic Mineral Technology Center explores these scientific, engineering or medical concerns with the objective of refining existing strategies and developing new respirable dust control techniquesand technology that are consistent with the fundamental dust-lung interaction processes that lead to mine worker disability. The work concentrates on five areas (FIGURE 35):"

Nov 1, 1988

Improve the safety of roof bolting machine operators working in underground coal mines while maintaining or improving efficiency of the roof bolting operation. Approach The Bureau of Mines funded research under contact to develop equipment that would assure greater safety in drilling holes and installing roof bolts. The research led to the design and fabrication of a roof-boiling machine that allows its operator to per-form drilling and bolting tasks while under permanently sup-ported roof or canopy protection. How the Prototype Works The major components of the remote-control roof bolter are a flexible-shaft drill that provides continuous drilling capability without the need to Stop to add drill extensions for long holes; a roof-bolt inserter that can bend a longer-than-seam height roof bolt into the drilled hole; and a roof-bolt lifter/torquer that completes insertion of the roof bolt into the hole and torques it to the desired tension.

Jan 1, 1986

By S. J. Anderson

The Bureau of Mines compared three methods of rock cutting using drag cutters under controlled laboratory conditions. The methods tested were the conventional drag cutting method used on continuous miners, the kerf-core method used on some boring machines, and an experimental method called ripper cutting. All three methods were tested in blocks of Indiana and Kasota limestone. The results of this testing showed ripper cutting to be 30 to 40 pct more energy efficient than both the conventional and the kerf-core methods in Kasota limestone and 35 pct more efficient than the kerf-core method in Indiana limestone. The conventional method was, however, 9 pct more energy efficient than the ripper method in Indiana limestone. These results are considered promising, and more tests are planned with the ripper cutting system.

Jan 1, 1987

By P. J. Dallimore

The Bureau of Mines has calculated general time-dependent solutions for radon diffusion from cylindrical and slab rock samples containing uniform radium distribution. Results have been obtained for several sets of boundary conditions. The method is suitable for determining the effective diffusion coefficient and the effective porosity for radon.

Jan 1, 1983

By H. Robert Ensminger

As a result of the new mining law implemented in August 1985 and the programs conducted by the Institute Ecustoriano de Mineria (INEMIN), which was created by this legislation, there was considerably greater activity in the nonfuels mineral sector during 1986. Over the next 2 years, INEMIN will be developing a national mining plan that will guide Ecuadorean mineral development for the balance of this century. As stage one of INEMIN's mineral study, historical records were reviewed and 300 abandoned mines and 1,200 unexplored mineral deposits were available for further investigation. In 1986, INEMIN established 5 branch offices and negotiated 250 new mining contracts with foreign companies valued at $16 million. Despite all this activity, INEMIN officials estimate that 100,000 square kilometers remain available for claim staking. Technical assistance contracts were signed with Belgium, the Federal Republic of Germany, Italy, Spain, and the United Kingdom, to assist in a variety of assignments ranging from helping prepare the national minion plan to the development of industrial mineral deposits.

Jan 1, 1988

By A. May

Florida has accumulated about 400 million tons of phosphogypsum, a mineral process waste generated in the production of fertilizer, and is adding 30 million tons to this annually. To minimize storage of this waste and reduce potential environmental effects, the Bureau of Mines conducted research into utilizing the phosphogypsum, by identifying and developing high-volume uses for this material. Admixtures of phosphogypsum, fly ash, and lime that could produce a coarse aggregate suitable for road construction were investigated. Using phosphogypsum with asphalt, cement, cement-kiln dust, silica, clays, and oxychlorides to pro-duce aggregate was also examined.

Jan 1, 1985

By Wesley A. Grosh

The Sutherland copper prospect is situated in Floyd County, Va. The immediate area was prospected around 1850, and one of the adits possibly dates from that time. Little or no ore has been mined from the deposit. The deposit is a mineralized sulfide zone occurring in mica schist and consisting mostly of pyrrhotite with minor amount of copper. A magnetometer survey of the deposit by the American Metal Co. in 1939 showed an anomaly that was thought to indicate a zone: of secondary enrichment. The Bureau of Mines diamond-drilled 14 holes, totaling 913 feet, and opened an adit during February and March 1943. No appreciable copper values or indications of secondary enrichment were found.

Jan 1, 1948

By John G. Kovac

A computer simulation has been developed by the US. Bureau of Mines to estimate the chances of a miner making a successful escape while wearing a self-contained self-rescuer (SCSR). The model takes into account (1) training in the use of SCSR's, (2) apparatus integrity, and (3) oxygen cost of a mine escape. This report examines survival odds for a prototypical escape, and illustrates how these odds change when SCSR training is improved.

Jan 1, 2009

Identify specific sources and the relative levels of contribution of various components of longwall shearer operations to the total airborne respirable dust generated during mining. Approach A research investigation was conducted in two phases by the Bureau of Mines at five mine sites to identify specific dust sources and their relative importance during long-wall shearing operations. During phase I of the project the specific longwall mining elements identified for evaluation were: cutting, sumping, tramming, conveying, and moving roof supports. During phase II of the project, two dust sources were evaluated: clearance ring cutters cutting in six-inch web width increments, and loading operations. Investigation Results As a result of dust measurements, the gage cutters were determined to be the major dust-generating source on the shearer. These cutters, at 6-inch web depth, produce three times as much dust per unit volume as is produced at 30 inches full web depth. The following list of averaged values for the mines tested shows that shearer cutting generated averaged dust levels four times as high as those generated by conveying, and approximately five times as high as those generated in moving roof supports.

Jan 1, 1984

By M. L. Whisman

Several commercial processes for reclaiming used lubricating oil were duplicated on a laboratory bench scale. Laboratory tests were selected and in some instances modified to determine the physical properties of each oil produced. In addition, the hydrocarbon composition of some samples was determined using a liquid chromatographic technique, and compared with the composition of new oil in order to determine the severity of the re-refining technique. Selected samples of reprocessed oil were reformulated with an additive package for further estimates of quality as determined by wear, corrosion, foaming, and oxidation stability tests. Additionally, several samples of commercially re-refined oil and new oil were obtained and physical properties were determined for comparative studies.

Jan 1, 1974

This Bureau of Mines report summarizes the research, development, and evaluation demonstrations conducted by the Bureau of Mines under the Health and Safety Act of 1969 to improve the means of notifying miners underground, who are away from their own phone, that they are being called.

Jan 1, 1977

By John C. Edwards

To have the capability to predict the development of localized spontaneous heating within a porous coalbed that is subjected to forced air ventilation or in an otherwise quiescent environment in which buoyancy develops, the Bureau of Mines developed three time-dependent mathematical models, which were used to calculate the temperature increase associated with chemisorption of oxygen by the coal. In each model, spontaneous heating is driven by an Arrhenius first-order reaction between the oxygen and coal. Two models are two-dimensional, and one is one-dimensional. In the first two-dimensional model, a constant-velocity forced convection airflow is specified; and in the other, buoyant flow is allowed to develop in the absence of forced convection. The third model evaluates the airflow from Darcy's law and a specification of the pressure at the surface of a one-dimensional porous coalbed. Numerical computations demonstrated how each model could be used to predict the onset of spontaneous heating when the porous coalbed was subjected to constraints of an imposed internal heat source or a high- temperature airflow. The effects of particle size and coalbed compaction upon spontaneous heating were examined with the third model.

Jan 1, 1990

Improve the effectiveness of person-wearable self-contained self rescuer (PWSCSR) training by enhancing the memory retention of trainees in proper donning procedures. Background In the fall of 1989, a total of 185 miners and inspectors were trained by Bureau of Mines personnel to don the SR-100 PWSCSR using the Bureau's 3+3 method. With the exception of a few individuals, miners were trained underground in an area set up within their working sections. The instructional protocol was as follows: (1) after placing an SR-100 simulator (equipped with a cleaned and disinfected mouthpiece assembly) on the mine floor in front of the worker, a researcher guided him or her step-by-step through the complete donning procedure, (2) the miner was required to perform each step slowly, methodically, and correctly while being talked through the sequence, (3) following this pre-practice instruction, the apparatus was repacked and the subject donned the device without coaching, while being evaluated, (4) if an error was made, the worker received corrective feedback, the unit was repacked, and the entire donning trial was redone. This procedure was repeated until the miner achieved a perfect 3+3 sequence.

Jan 1, 1990

By Michael S. Wieland

The work-principle from thermodynamics was used to formulate a model for predicting toxic fumes from mining explosives in underground chamber tests, where rapid turbulent combustion within the surrounding air noticeably changes the resulting concentrations. Two model constants were required to help characterize the reaction zone undergoing rapid chemical transformations in conjunction with heat transfer and work output: a stoichiometry mixing fraction and a reaction-quenching temperature. Rudimentary theory with an unsteady uniform concentration gradient was taken to characterize the combustion zone, yielding 75% for the mixing fraction. Four quenching temperature trends were resolved and compared to test results of ammonium nitrate compositions with different fuel-oil percentages (ANFO). The quenching temperature 2345 K was the optimum choice for fitting the two major components of fume toxicity: carbon monoxide (CO) and total nitrogen oxides (NOx). The resulting two-constant model was used to generate comparisons for test results of ANFO compositions with additives. Though respectable fits were usually found, charge formulations which reacted weakly could not be resolved numerically. The work-principle model yields toxic concentrations for a range of charge formulations, making it a useful tool for investigating the potential hazard of released fumes and reducing the risk of unwanted incidents. Keywords: Toxicity; Fumes; Explosives

By Ronald D. Hill, Elmore C. Grim

The removal of overburden often exposes pyritic materials (iron disulfide). As shown in equations 1 and 2, the oxidation of this material results in the production of ferrous iron and sulfuric acid. The reaction then proceeds to form ferric hydroxide and more acid, as shown in equations 2 and 4. [ ] Consequently a low pH water is produced (pH 2-4.5). At these pH levels, the heavy metals such as iron, manganese, copper, and zinc are more soluble and enter into the solution to further pollute the water. Water of this type supports only limited water flora, such as acid-tolerant molds and algae; it will not support fish life, destroys and corrodes metal piers, culverts, barges, etc., increases the cost of water treatment for power plants and municipal water supplies, and leaves the water unacceptable for recreational uses. The amount, and rate of acid formation, and the quality of water discharged are a function of the amount and type of pyrite in the overburden and coal, time of exposure, characteristics of the overburden, and amount of available water(l). Crystalline forms of pyritic material are less subject to weathering and oxidation than amorphic forms. Since oxidation by oxygen is the primary reaction during early acid formation, the less time pyritic material is exposed to air, the less acid is formed. Thus, a positive preventative method is to cover pyritic materials as soon as possible with earth, which serves as an oxygen barrier. In terms of mining, this step is accomplished by current reclamation techniques and small open pits.

Jan 1, 1974

By James A. West

THE South Asian countries of India, Ceylon, Pakistan, Afghanistan, Nepal, Bhutan, and Sikkim have a large variety of mineral resources; however, in spite of mineral industry growth during 1964, development of resources remained far short of possible development, and, in terms of value of trade in minerals, the area remained a sizeable net importer. India's mineral industry is by far the most significant; its minerals production in 1964 accounted for more than 90 per cent of the total value of all minerals produced in the area. The total value of all minerals produced in South Asia in 1964 was only about 1 percent of the area's estimated gross national product of $55,125 million. Despite the rather small current contribution of minerals to the economy, development of mineral resources figures prominently in plans for the industrial development of the nations of this area.

Jan 1, 1966

Reduce longwall shearer operators' dust exposures by more effectively suppressing the dust generated by the upwind cutting drum. Approach Direct more of the shearer water supply to the upwind drum, thus reducing the shearer operator's exposure to respirable dust while making more efficient use of water. How Proportioning Permits More Efficient Use of Water On most longwall mining operations, the cutting action of the shearer drums is the primary source of dust. Al-though the amount of dust generated is directly related to the amount of coal and rock cut by the drum, the exposure or the shearer operators to dust depends more on their work position relative to the upwind drum. When cutting with the airflow, the upwind drum, cutting bottom coal and floor rock, is the primary generator of dust reaching the operators. The lead drum is downwind of both shearer operators and is thus of less concern. (See diagram). When cutting against the airflow, the lead drum is upwind-taking a full cut, including roof rock-and both shearer operators may be exposed to very high levels of respirable dust. Currently, water sprays mounted on the cutting drum provide the most effective method of controlling dust from longwall shearer drums, and all longwall mining operations use some type of bit flushing or cavity filling water spray system on the cutting drums. Bureau surveys of longwall operations, conducted as part of its research program to reduce respirable dust, have indicated that six longwalls with better than average compliance records use higher than normal water flowrates to the cutting drums. The average water flow to the shearers at these six operations was approximately 60 gpm-about 50 percent more water than is normally supplied to double-drum longwall shearers.

Jan 1, 1982