Search Documents

The compilation of the sampling nomogram is an essential tool in the optimization of a sampling protocol and allows the operator to track the change in relative variance of the sampling error (the Fundamental Sampling Error) during steps of comminution and mass reduction in the process of recovery of the aliquot for analysis. The data required for the compilation of the nomogram are centered on the sampling constant K and the exponent, alpha (a), of the nominal fragment size. Five methods for establishing K have been identified, but two of them, the duplicate sampling analysis (DSA) method and the heterogeneity test (HT) method purport to provide such a constant. The step by step procedure for each of these two methods was examined using broken ores from three mines, Mponeng mine, Kloof mine and Lily mine. Two of these mines (Mponengand Kloof) are typical Witwatersrand-type gold mines, while the third is an Archaean-type, shear related gold deposit situated in the Barberton Greenstone belt. The results suggest that the factor K derived using the heterogeneity test is very accurate, but applies only to a single size fraction in the spectrum of comminuted materials. The calculation of gold grain sizes using this method appears to be too small and does not conform with the results from detailed mineralogical studies. The factors K and alpha derived using the duplicate series analysis, are appropriate for use across a wide spectrum of comminution sizes and also provide realistic gold grain sizes, comparable with the equivalent circular diameter of gold grains identified in mineralogical studies of the ores.

Jan 1, 2009

By X. Ndlovu

Underground observations in a coal mine have indicated failure oft he immediate roof above the bords. Careful observations and photographic recording of occurrences of these roof failures, termed ?roof guttering?, have been made. The occurrence of guttering results directly in roof instability, and indirectly, due to the interaction of the guttering with natural planes of weaknesses in the immediate roof rock. In this paper, relevant observations of roof guttering, possible mechanisms of formation of roof gutters, laboratory testing for determination of material strength and deformation properties, and numerical analyses to explain underground observations are described. Mapping of roof failures showed that these took place mainly towards the centre of the roadways. Roof guttering was observed often to occur violently and with little warning. Occurrence of roof guttering has a negative impact on production?some panels are abandoned, production times are increased and safety of workers is compromised. The numerical stress analyses showed that, although none of the constitutive behaviour criteria used predicted the observed underground failures correctly, the extension strain criterion gave the best agreement.

Jan 1, 2007

Excessive dust generation from unpaved mine haul roads is a problem common to most surface mining operations. While optimal road wearing course material selection parameters reduce the inherent dust generation potential, they do not totally eliminate fugitive dust. Many different classes of suppression or palliative treatments are available for mine haul roads and this paper initially ascertains basic selection guidelines, using a set of ideal dust palliative product, application and performance parameters based on mine road-user requirements. An evaluation and modelling methodology for truck generated fugitive dust emissions is developed as a basis for the comparative assessment of dust control strategies. For water-based spraying, a watering model was developed to estimate individual mine road watering frequencies for characteristic site parameter combinations during summer and winter operating conditions, for a required level of control or maximum dust defect. This forms the base-case scenario with which to compare the performance of other types of dust palliatives under the same conditions. Finally, a basic palliative economic evaluation model is introduced with the aim of identifying and costing the establishment, application and maintenance rejuvenation activities associated with the use of chemical palliatives. While palliative cost and performance is generally site specific, it is shown that under certain combinations of conditions, the use of dust palliatives has the potential to deliver cost savings when compared to water-based spraying.

Jan 1, 2007

By D. F. Malan

Considerable practical knowledge and effective use of empirical evidence is required in the design of tunnel support systems. In many instances, it is unclear how individual support elements interact with fractured rock and which elements of the support system are critical in controlling and containing the movement of material proximate to the excavation. The present paper outlines a displacement discontinuity approach that allows the coupling of surface constraints, in the form of liner or mesh material, to an explicit representation of time-dependent rock discontinuity creep movements. The method is illustrated for a simple square-shaped tunnel profile in which the fracture zone is mobilized by an imposed stress field. A crucial aspect of the model is the computational treatment of the coupling between the liner material and there presentation of the fractured rock mass. This allows the response of the liner material to be assessed quantitatively in terms of the possible reduction of movement in the rock mass. The importance of installing the liner timeously after the excavation is formed is illustrated in a specific example. A number of computational difficulties in simulating liner-rock interaction mechanisms are identified.

Jan 1, 2008

By F. S. Beretta

Mineral processing efficiency depends on various factors and among them includes head grade fluctuations feeding the processing plant. Head grades can fluctuate beyond an admissible range, implying in recovery decrease for the mineral of interest. Grades feeding the processing plant depend on the geological domain which is being mined and on the mining schedule. Therefore, it is necessary to keep grade variability controlled. Blending piles are an efficient alternative to reduce grade fluctuations. The main factors influencing blending efficiency are the pile size or its mass and the number of layers used to pile up. Large piles are more efficient to reduce variability, however, there are economical and operational limits associated with them. This study investigates a methodology to analyse the ideal pile size to reach an acceptable variability given the in situ grade fluctuations. Geostatistical simulations provide the means to assess grade variability using an optimized mining schedule. These block grades are used to simulate any given pile throughout the mine`s life. The methodology was illustrated using a case study to control coal ash content at a mine supplying ROM coal to a power plant. Keywords: homogenization, piles, geostatistical simulation.

Jan 1, 2009

By P. Altounyan, K. Akermann, T. Van den Berg

Amandelbult Mine is currently undertaking a trial to mechanise the mining of the UG2 reef through the introduction of room and pillar mining. As part of the trial, a system of managing the control of the hanging wall has been introduced, based on systems and technology that are proving successful in the nearby coal mining industry. The principal features are the use of a high bond strength, stiff bolting system which can be easily installed to a high standard, and a range of in situ tests and measurements to optimise the level of support installed to control the movement of the hanging wall. The rock bolt system and the measurements and tests described are new to the platinum mining industry. The paper describes these systems and their adaptation and application to hard rock mining. La Mine d’Amandelbult est actuellement dans des essais en vue de mécaniser l’extraction dans la veine UG2 grâce à l’introduction d’une exploitation par chambres et piliers. Dans le cadre de ces essais, un système de gestion de la paroi suspendue a été introduit, base sur des systèmes et une technologie qui prouvent donner de bons résultats dans l’industrie voisine d’extraction de la houille. Les caractéristiques principales sont l’utilisation d’un système de verrouillage raide et à forte adhérence qui peut être installé à un haut niveau de qualité et une gamme d’essais et de mesures in situ pour optimiser le niveau de soutien installé pour contrôler le mouvement de la paroi suspendue. Le système de verrouillage de la roche ainsi que les mesures et les essais décrits sont une nouveauté dans l’industrie minière du platine. La communication décrit ces systèmes ainsi que leur adaptation et leur application à l’exploitation minière en roche dure. Amandelbult Mine unternimmt gegenwärtig einen Test um den Abbau des UG2 Riffs durchEinführung des Kammerpfeilbau zu mechanisieren. Als Teil dieses Tests wurde ein System zur Kontrolle der Stollenfirstes eingeführt, welches auf jenen Systemen und Technologien basiert, diesich im nahe gelegenen Kohlebergbau als erfolgreich erwiesen. Die prinzipiellen Charakteristikasind der Gebrauch von einem steifen Bolzensytem mit hohem Verbundwiderstand die leicht zueinem hohen Standard gebracht werden können, und eine Reihe von in-situ Tests und Messungenum das Niveau der installierten Unterstützung zu optimieren, und um die Bewegung desStollenfirstes zu kontrollieren. Das Gesteinsbolzensystem, die Messungen und die Tests, diebeschrieben werden, sind neu in der Platinbergbauindustrie. Diese Arbeit beschreibt diese Systeme, deren Anpassung und Anwendung im Hartgesteinsbergbau.

Jan 1, 2003

Book Reviews M. J. Jones(ed.). Geological, mining and metallurgical sampling London, The Institution of Mining and Metallurgy, 1974. 268 pp. £8. Spooner, J., et al. (eds.). 1974 miningannual review, London, The Mining Journal Limited, June 1974. 506 pp. £14,25 (including annual subscription to Mining Journal and Mining Magazine). J. H. Quilliam et al. (eds.). The ventilation of South African ~old mines. Johannesburg, Mine Ventilation Society of South Africa, 1974. 488 pp. RI0,00. The Hans Merensky Foundation As announced in a recent brochure, the 25-year-old Hans Merensky Trust has been converted to The Hans Merensky Foundation, its main objective being 'to promote and assist in the development of the resources of the Republic of South Africa and neighbouring territories articularly such natural resources as soil, water, minerals, flora and fauna-and to promote the health and welfare of the inhabitants; more specifically by research, experiment and demonstration and through the correlation and application of scientific knowledge'. Applications for S.A.I.M.M. membership and transfer Please note that new application and transfer forms have been issued.

Jan 11, 1974

By I. Ashmole

From the point of view of the environmental impact created, dimension stone mining is a relatively benign industry. There are no emissions besides those of the diesel powered earthmoving equipment utilised in its extraction and a small amount of blasting gases. Contamination of water resources is only likely in the event of petrochemical spillages from storage facilities and equipment, and these can largely be either prevented or cleaned up effectively. The major environmental impacts are of a visual nature, while in sensitive areas, habitat destruction and the destruction of archaeological heritage may become significant impacts. The dimension stone industry has grown at an average rate of over 7% per annum since 1986, and is forecast to continue growing at this rate for the foreseeable future. The cumulative environmental impact of the industry will thus become more significant over time. This paper discusses the environmental impacts of dimension stone mining and recommends effective means for dealing with the practical aspects of reclamation and mine closure in dimension stone mining within the context of environmentally responsible business practices. The discussion focuses mainly on the operations of the Finstone Group in Southern Africa, which are considered to be world leaders in the application of environmental management within the dimension stone mining industry, although reference is also made to other situations which the authors have encountered at dimension stone quarries around the world.

Jan 1, 2008

By D. Krebs, Tero Korhonen, X. Yang, A. Kirpala, N. Heino

At present, over 85% of the world’s rare earth oxides are produced from the bastnäsite ores, found mainly in China. Meanwhile, the ion adsorption ores are the most important sources for heavy rare earth production. As the demand for rare earth materials in the world increases, other forms of rare earth deposits will become new potential resources of rare earth production in the future. In this paper, flotation performance of a steenstrupine ore from the Kvanefjeld deposit for rare earth recovery was studied through laboratory bench testwork. The effects of various factors including grinding size and collector dosage on recovery and selectivity of the selected rare earth elements, La, Ce and Y, were investigated. A rare earth concentrate with the grades of La 2.8 wt%, Ce 5.1 wt% and Y 1.0 wt% at recoveries of 80.5% La, 79.8% Ce and 55.3% Y was obtained in optimum conditions. Further potential to improve the efficiency of REE flotation was discussed. Keywords: Rare earth elements, flotation, steenstrupine, Kvanefjeld deposit

Jan 1, 2020

By Z. Khan

Iron, in the form of steel and stainless steel, is the most commonly used metal in the world. Plain steels corrode and oxidize easily, while stainless steels exhibit improved corrosion and oxidation resistance. It has been found that rare earth metal (REM) additions, such as cerium and erbium, result in the improvement of the abovementioned properties in iron-containing compounds. Gadolinium is a REM, however, there is very little information available on the influence of gadolinium on the microstructure and mechanical properties of iron-containing compounds. Thus, the purpose of this research project was to determine the influence of gadolinium additions on the microstructure and mechanical properties of mild steel and 316 stainless steel. Ten alloys were produced for the purposes of this research. Five of the alloys had a base composition of mild steel while the remaining five had base composition of 316 stainless steel. The alloys for each of the base composition contained gadolinium additions of 0.1, 0.5, 1.2, and 5 weight per cent. The as-cast and the cold-rolled alloys were analysed. The alloys responded well to the cold-rolling with the exception of the 5 weight per cent gadolinium mild steel and stainless steel alloys. These alloys were extremely brittle and underwent a significant amount of cracking during the cold rolling process. A microstructural analysis of the alloys was conducted using a light optical microscope, while the chemical analysis of the alloys was conducted using energy dispersive x-ray spectroscopy (EDS). The resulting microstructures and EDS analyses revealed that the gadolinium displayed minimal solubility in the ferrite matrix of the mild steel alloys and minimal solubility in the austenite matrix of the stainless steel alloys. Instead the gadolinium formed as an interdendritic secondary phase in both alloys. EDS analysis revealed that the secondary phase in both alloys was gadolinium-rich. Vickers microhardness tests conducted on both alloys revealed that the alloys were composite-like, with a hard, brittle gadolinium-containing compound dispersed throughout a softer, more ductile matrix. The corrosion resistance of the alloys was determined through potentiodynamic anodic polarization tests. Two solutions were used for the corrosion rate tests: a 0.5 weight per cent NaC1 solution and a 0.5 M H2SO4 solution. The results from the mild steel alloys revealed that in both the solutions, the corrosion potentials and the corrosion resistance of the alloys increased with increasing gadolinium concentration up to 1 weight per cent. The corrosion rate test results from the stainless steel alloys revealed that the passivation current density and corrosion resistance of the alloys increased with increasing gadolinium concentration in both solutions. The oxidation resistances of the mild steel and stainless steel alloys were determined through the use of a Netzstch Simultaneous Thermal Analyser. For both the mild steel and the stainless steel alloys, it was found that the oxidation resistance of the alloys increased as the concentration of gadolinium increased when compared to the as-received mild steel and stainless steel samples. This could be due to a strongly adhering gadolinium oxide scale that formed on the surface of the alloys and resulted in the protection of the mild steel and the stainless steel.

Jan 1, 2012

By G. M. Dunn

Pressure leach autoclave circuits are employed in the leaching of ores, concentrates, mattes, alloys and intermediates for the recovery of metals into solution. Once the metals are extracted into solution, the value metals can be recovered by hydrometallurgical means such as by purification followed by electrowinning, hydrogen reduction, pyrohydrolysis, crystallization and other unit operations. In many of these integrated flowsheets the pressure leach step is pivotal to the recovery of the value metals from the host material. Furthermore, the autoclave circuit invariably is a high capital cost component of the plant and an area that is carefully scrutinized when debottlenecking and capacity increases are being considered. This paper identifies a unique proven way of increasing the capacity of existing or new exothermic pressure oxidative leach autoclave circuits by as much as two or three times.

Jan 1, 2009

By H. C. Van Der Merwe

In the 21st century, dynamic, accurate digital 3-D geological models are essential to the pursuit of safe, efficient and profitable mining. This is particularly true for the deep-level underground mines in South Africa. The Sirovision® solution is a collaboration project between the Australian CSIRO (Commonwealth Scientific and Industrial Research Organisation), Datamine Software Ltd. and AngloGold Ashanti Ltd (AGA). The purpose of the project is to provide a fully integrated digital rock face imaging, geological mapping and modelling system for the AGA gold mining operations. The CSIRO-developed Sirovision® Stereo Camera Rig (SCR) consists of two digital cameras, alighting system, a laser guidance system and image processing software. The imaging system works on the principles of photogrammetry, i.e. overlaying of two 2-D images with a central focus point, with mathematical algorithms extracting 3-D information from the 2-D image pair. The output from matching several image pairs is a computer-generated, full 3-D, virtual copy of the mining excavation. The image resolution and relief ares of sufficient quality to distinguish different rock types and structural contacts. Functionality within Datamine Studio3 is used to add geological intelligence to the 3-D images provided by Sirovision®. The geologist identifies and ?draws? lines representing geological features directly onto the image. By utilizing the inherent ?topography? of the 3-D image, the software is able to convert the lines into 3-D surfaces, ready for use in the 3-D geological model. Subsequent to promising underground test results from AGA?s Sunrise Dam Gold Mine (SDGM) in Australia and other mining operations worldwide, it was decided to test the Sirovision® system in the South African deep-level gold mines. The first underground tests at Moab Khotsong Mine began in January 2009. The objectives of these tests entailed the capturing of 3-D images of selected development ends, mapping of geological features onto the 3-D images and integration of the mapping data with the 3-D geological model. Some downsides have cropped up during the feasibility testing, related to practicality of the SCR for acquisition of 3-Dimagery in the deep-level underground operating environment. These constraints will have to be addressed prior to operational implementation. Facing such difficulties is not unusual when attempting to implement new technology in such a challenging working environment and testwork is still in progress at the mine in order to prove the concept of using this technology in a Witwatersrand underground gold mine. The great advantage of the Sirovision® solution is that it offers the geologist the opportunity to work remotely on a 3-D virtual copy of a mining excavation, without the heat, humidity, hazards and time constraints associated with physical mapping in an underground workplace.

Jan 1, 2009

By D. J. Bosman

The impoved densification of sludge from neutralized acid mine drainage. by D. J. BOSMAN, B.Sc., (Member) The paper describes an investigation aimed at finding a solution to the accumulation of acid mine drainage in the old workings at Coronation Collieries, Kromdraai. The problem involved the neutralization of the acid in the water, without the large volumes of sludge and the large amounts of dissolved solids that usually result from neutralization. Pilot-plant work on the site using a limeneutralization process developed at Bethlehem Steel Corporation (U.S.A.) showed this to be a feasible method. A sludge of 22 per cent density was obtained under optimum operating parameters. The amount of suspended solids in the overflow water was very high, but this does not give rise to concern because the full-scale plant at Kromdraai will practise secondary sedimentation by running the thickener overflow through large dams with a theoretical retention time of 25 days. An analysis of the theory underlying the process is also made.

Jan 4, 1974

By T. Könighofer

Processing of copper-cobalt orebodies in Africa?s Copper Belt has received much recent attention with various flowsheet options being developed specifically for the refining of cobalt. The upfront leach and copper refining routes are well understood whereas the refining of cobalt is more complex, requiring numerous impurity removal steps to produce high purity metal. This paper describes an investigation into one of the possible processing steps in the refining of cobalt, namely, cobalt solvent extraction. The paper emphasizes the importance of upstream impurity removal to achieve the required cobalt solvent extraction feed composition. 18% (v/v) Cyanex 272 in an aliphatic diluents is used as the organic phase. The pH profiles in the various stages are evaluated in order to obtain a raffinate containing <10mg/l cobalt and with a low magnesium content reporting to the stripping section. The pH profile is also used to minimize the impurity deportment to the cobalt electrolyte. The effect of adding a pre-neutralization stage before feeding the organic phase to the extraction circuit is investigated. Zinc build-up in the stripping stages is also looked at. It is recommended for the purpose of this study that four extraction stages at an O:A ratio of 1 with a pH profile from 4.9 to 5.7 be employed. The pH is controlled with 40g/l NaOH. A pre-neutralization stage is required, where the organic phase is contacted with 10 M NaOH. Two scrubbing stages are recommended at an O:A ratio of 40, using the cobalt electrowinning advance electrolyte as the scrub liquor. Three strip stages are to be employed at an O:A ratio of 0.67.

Jan 1, 2009

By J. Stacey

There are four components to this guideline 1. Guidance on the socio-economic aspects of closure policy 2. Socio-economic closure activities mapped against the mining project life-cycle (a ?check status? tool) 3. A process guide for mine closure planning and implementation 4. Tools in support of mine closure planning and implementation How to use this guideline The four components are part of a hierarchy with: ?Overarching policy as the starting point ?The mine life cycle model as a quick process check tool ?The process guide for detailed practical planning and implementation as practical guidance ?Supportive tools as resources to address specific planning and implementation steps.

Jan 1, 2010

By J. Rabe

Tasked with developing a flow sheet for a new resource, one typically turns the experts for help. The advice of an expert can be invaluable in reducing the time and costs associated with characterizing an ore (not to mention extracting maximum information from limited samples). While guiding and optimizing a metallurgical concept study requires a certain skill set, selling a project is something different. The metallurgical specialist is usually not responsible for sharing the results of investigations with potential investors. However, the person responsible for selling the project can ensure that a metallurgical concept study is conducted thoroughly and responsibly without having the ability to do the work, while being sufficiently familiar with the metallurgical aspects to authoritatively sell the project. The process of identifying suitable process routes through to constructing a concept flow sheet and mass balance is discussed as a basic example. From basic mineralogical information and a thorough literature survey, the most likely beneficiation routes can be identified and targeted testing conducted. The final top size will depend on the required product properties (mainly grade), the selected beneficiation technology, and the ore?s liberation properties. Once the required top size has been identified, comminution options can be evaluated. Once again, literature surveys can be used to supplement concept-level comminution property information, and select possible equipment and circuit configurations. Marketing, material handling, and logistics-related information can be used to determine required dewatering technologies. At this stage, enough information is available to develop a concept mass balance and conduct basic equipment sizing..

Jan 1, 2014

Corosion technology: An information source book, by Judith Ann Douvile. Taylor & Francis, 1989. 188 pp. £32. Stainless steel buyers guide 1990. Southern Africa Stainless Steel Development Association (P.O. Box 4479, Rivonia, 2128), 1990. Free. Fatigue and stress of engineering materials and structures, edited by H.P. Lieurade. ITT International (40 Promenade Marx-Dormoy, 93460 Gournay-sur- Marne, France), 368 pp. US$ 109. Titanium and aluminium, edited by P.A. Coulon. ITT International (40 Promenade Marx-Dormoy, 93460 Gournay-sur-Marne, France), 200 pp. US$ 80. Engineering applications of stochastic processes. Theory, problems and solutions, by A. Zayezdny, D. Wulich, and D. Tabak. Chichester, John Wiley, 1989. 525 pp. £54.50. Metal behaviour and surface engineering, edited by S. Curioni, B. Waterhouse, and D. Kirk. ITT International (40 Promenade Marx-Dormoy, 93460 Gournaysur- Marne, France), 413 pp. US$ 109. Fuzzy control and fuzzy systems, by W. Pedrycz. Chichester, John Wiley, 1989. 272 pp. £37.50. CILO (carbon-in-leach with oxygen) cost study, by Minproc Engineers (USA). Free.

Jan 1, 1990

By RT White

For a number of years the steel tube and pipe industry has worked on resolving problems of product quality. These have largely been resolved and new products have been developed to take advantage of new developments. To fully coordinate market acceptance guidance on use of galvanized piping was also required. This was largely achieved locally in 2004 with the publication by the SABS of ARP 060 - Guidance on the use and application of hot dip galvanized steel piping for the transportation of potable water in South Africa. Use of this document is not easy however and a need to have a simple computer model to assist the specifier was identified. Working with a major tube and pipe manufacturer this is now being developed and this paper will provide the background to the model?s development and its intended use. There is still a need for a partner Code of Practice on the performance of galvanized piping in buried conditions and the need for this will be highlighted together with current available information.

Jan 1, 2006

By J. W. Wilson, P. C. Graham

Raise-boring experiences in the gold mines of the Anglo American Corporation Group by J. W. Wilson M.Sc., M.I.M.M., F.S.A.I.M.M., M.A.I.M.E. and P. C. Graham M.Sc. (Eng.) Gold mining is being carried out at ever-increasing depths in South Africa. For reasons of safety and human comfort, it is becoming imperative for raises to be developed by means other than conventional drilling and blasting. Raise-boring is an attractive alternative method. Initial raise-boring experiences in South African gold mines showed disappointingly high costs due to the abrasivity and difficulty of drilling Witwatersrand quartzites. Consequently, a research and development project was instigated with the objective of making raise-boring an economically viable technique in hard abrasive rock. A Robbins 61R raise-borer was made available to the Research and Development team and a number of raises have been drilled. During these trials two advances in cutter design were tested. This paper presents the results obtained, including drilling costs, and provides details of the equipment used.

1. Publications of the World Mining Congress Series A: Volume 5 World mining data &apos;90. US$25. Series B: Volume 1 Chromite. US$31. 2. Randol publications The folowing publications are available from Randol International Ltd, P.D. Box 150632, Lakewood, CD80215, U.S.A.). Randol Gold Conference, Sacramento &apos;89. 1990. 400 pp. $80. Randol mining directory 1990-1991. 1990. $100. Randol buyer&apos;s guide USA and Canada. 1990. $50. 3. New journal Industrial Metrology, edited by A. Choudry et al. Amsterdam, Elsevier Science Publishers, 1990. Dfl. 266 incl. postage for 4 issues per year. 4. Mintek reports The folowing reports are available from Mintek, Private Bag X3015, Randburg, 2125 South Africa. They are available at R35 (including GST) per copy to SouthAfrican addressees, and US$30 per copy (including airmail postage) to addressees elsewhere. Report M130D The application of a standard leaching procedure to tin-tungsten concentrates from Van Roois Vley deposit: Cross-cut bulk samples, by M.M. Fieberg and C.F.B. Coetzee. First issued 1984, reissued 1990. 11 pp. Report M160D The recovery of graphite from the Messina district, by R.N. Guest. First issued 1984, reissued 1990. 22 pp. Report M305D The beneficiation of nickel-copper ore from Uitkomst, by P.W. Dverbeek. First issued 1987, reissued 1990. 55 pp. Report M320D The flotation of pyrite from Bufe/sfontein Gold Mine, by A.M.R. Botelho de Sousa and V.E. Ross. First issued 1988, reissued 1990. Report M347D A utogenous miling of ore from the UG-2 Reef, by J.K.H. Lichter. First issued 1988, reissued 1990. 13 pp. Report M352D Fly ash as an adsorbent or precipitation agent in the removal of ionic species from solution, by C. Pohlandt-Watson, S.M. Graham, and K.F.G. Brackenbury. First issued 1988, reissued 1990. 9pp. Report M360D Beneficiation of limestone from Pienaars River, by R.N. Guest. First issued 1988, reissued 1990. 23 pp. Report M364D The recovery of gold from deposits in the Pilgrim&apos;s Rest area, by R.A. Burger. First issued 1988, reissued 1990. 15 pp. Report M396 Reduction of chromite spinels in iron-chromiumcarbon aloys, by R.H. Eric and E. Uslu. Mar. 1990. 33pp. 5. New review Diverless and deepwater technology. Advances in underwater technology, ocean science and ofshore engineering, edited by the Society for Underwater Technology. London, Graham & Trotman Limited, 1989.224 pp. £55.

Jan 1, 1990