Search Documents

By V. N. Medvedev, A. M. Bryukhanov

Stationary mine air control equipment enables monitoring of CH4 concentration only in sensor locations. CMC-4 individual indicator built into a caplight has been developed in Ukraine, extending CH4 monitoring to manned job sites. Major technical characteristics of the indicator are demonstrated. It features two operation thresholds: 1st threshold 1.0 to 2.0% vol. 2nd threshold 1.5 to 2.5% vol. Basic absolute accuracy ± 0.2% Caplight battery is a common power supply for the lamp and CH4 indicator, providing at least 10 hours of the system non-stop operation. Average pre-failure life is at least 10,000 hrs. It features: an explosion proof design and intrinsically safe test circuit; a small-sized sensor as an integral part of the caplight; a hybrid microcircuit to facilitate functioning of methane monitoring unit. The CMC-4 indicator weight is the weight of the caplight itself and equals 2.4 kg. A two-threshold design makes possible to distinguish between methane sources: slow accumulation due to diffusion or sudden rushes due to a gas-dynamic event. CMC-4 indicators in addition to stationary equipment minimize the risk of CH4 explosion underground determined as a product of accident intensity by calculated time interval.

Jan 1, 2003

By D. G. Krige

The problem addressed is that of estimating grade differences between sub- divisions of a new gold mining prospect when only borehole results are available. Such differential grade estimates are required in choosing the best area for initial production, and in defining the grade profile over the mine's life for purposes of feasibility studies. It is also often necessary to differentiate between the grades and hence the values of subareas, owned by separate companies, for the purpose of fixing relative share participation percentages in the new mining company. It is shown that exaggerated grade differentials will be obtained from grade estimates of the subareas based only on boreholes within each such subarea, respectively, and that it would be more realistic to apply some 'smoothing', preferably by kriging. This is feasible because the lognormal-de Wijsian model can be used to give an indication of the spatial structure for the boreholes, even where they are spaced far apart; also the degree of 'smoothing' indicated is shown to be relatively insensitive to inaccurate estimates of the relevant semivariogram parameters.

Jan 1, 1987

By L. W. Helle

In this investigation, which was conducted at the Metallurgical Research Plant, Lulea, Sweden, a series of experiments were carried out using a water-model to simulate the gas rinsing of a ladle containing liquid metal. The factors examined include the effect of gas flowrate, the position of a porous plug or lance, the immersion depth of the lance, and the geometry of the bath at the time of complete mixing. Mixing times were recorded by conductivity measurements. The results showed that there is a threshold level for mixing above which no advantage is to be gained from an increase in the gas flowrate. It is suggested that the results can be applied to rinsing ladles in working situations, the levels being approximately 270 dm3/min for 40 t ladles and 780 dm3/min for 150 t heats. The optimum siting of the lance or porous plug is a position that is three-quarters of the internal radius from the centre of the ladle with the lance penetrating as deeply as possible into the ladle. The best design of liquid bath is that having a diameter-to-height ratio of I. An equation was developed for the calculation, by dimensional analysis, of the time required for mixing during gas rinsing, and a comparison of the calculated mixing times with the results from production trials shows a satisfactory agreement (with a correlation factor of 0,91). Thus, an equation is available for the calculation of the stirring time needed to completely mix the bath in production situations.

Jan 1, 1981

By S. L. Crouch

This paper describes a numerical procedure for the computation of the displacements and stresses induced by the mining of a tabular ore deposit in faulted ground. The numerical procedure is based on the displacement discontinuity method, which can be regarded as an application of Salamon's 'face element principle' to cases in which the reef plane is faulted into several sections, or even folded in an arbitrary way. An element of a fault is modelled in the same manner as an element of the reef, except that a fault element is allowed to undergo permanent inelastic deformation (i.e., slip) if the stresses transmitted through the fault-filling material satisfy a Mohr-Coulomb yield condition. An iterative technique for the incorporation of a Mohr-Coulomb yield condition in the general displacement discontinuity method is explained. This technique is illustrated by means of a simple example involving the mining of a flat-lying reef intersected by a fault. The displacements and stresses at selected locations along the fault are examined as the reef is mined, element by element. A consideration of the energy changes reveals that the occurrence of slip along a fault leads to a sudden increase in the energy release rate due to mining as the excavation intersects the fault. The energy release rate then falls off abruptly to a value less than that which would occur in the absence of any slip, and gradually builds up to re-establish the conditions that would exist in unfaulted ground.

Jan 1, 1979

By Y. C. Kim

The estimation of local recoverable reserves using the widely spaced exploration drill hole information in an open-pit mine is probably one of the most difficult tasks in ore reserve estimation. The difficulty of this problem is magnified if the grade distribution is highly skewed, such as in a gold deposit. This paper describes the results of performance comparison of three different kriging techniques in an open-pit gold - silver deposit. The three different kriging techniques compared in their local recoverable reserve estimation capabilities are: (1) lognormal kriging, (2) indicator kriging, and (3) probability kriging. For performance comparison, the predictions are compared with the actual recoverable reserves determined from blast hole information. Based on the results from one test bench, both indicator and probability kriging performed better than lognormal kriging, perhaps owing to samples not being truly lognormal. Between indicator and probability kriging, probability kriging results were definitely superior to indicator kriging results.

Jan 1, 1987

Cutting strong rock with a drag bit assisted by high-pressure water jets By M. HOOD. B.Sc. Hons. (Min. Eng.). B.Sc. (Mech. Eng.). A.M.I.M.M. (Visitor) Experiments are described that led to the discovery that coherent high-pressure water jets directed immediately ahead of drag bits while they are cutting strong rock reduce the magnitudes of the forces on the bits significantly. Tests were carried out to assess the effects of the pressure of the water jets on bit-cutting performance. The pressure was varied between 10 MPa and 50 MPa, the water flow rate being a constant 30 I/min. Over this pressure range, the force on the bit was reduced to the extent that the depth of cut of the bit was at least doubled with the point of impingement of the jets optimized. Forces on the bit were found to be particularly sensitive to the point of impingement of the water jets relative to the bit. The optimum configuration was found to be with two jets, one directed towards each corner of the bit and impinging on the rock approximately 2 mm ahead of the leading edge of the bit. Experiments in which a drag bit and high-pressure water jets were used to cut strong abrasive quartzite in the underground mining situation have demonstrated a potential increase of up to five times in the average depth of cut due to reduction of the forces on the bit. The results from the underground tests indicate that the life of the bit is improved significantly - by a factor of approximately two - when highpressure water jets are used.

Jan 11, 1976

By C. Musingwini

The South African platinum mining industry is using a number of different mining methods, including variations of the same method, to extract the narrow reef tabular platinum deposits of the Bushveld Complex. These mining methods fall into three broad categories, namely conventional, mechanised and hybrid mining. A question sometimes asked in the industry is whether mechanized mining methods are more efficient than conventional mining methods. An objective answer requires the methods to be evaluated against multiple criteria simultaneously, whereby each criterion has a relative degree of importance in the overall decision. The most efficient method is the one that scores highest on each criterion. However, some of the criteria can be conflicting, such as by increasing dilution the shaft head grade decreases. The analytic hierarchy process (AHP) methodology was selected for the study because it is used to solve problems of this nature. A survey was carried out to determine the relative importance of each efficiency criterion by drawing on the knowledge and experience of mine technical services and project management practitioners in the industry. Efficiency data for four different mining methods drawn from the Egerton (2004) study were used as a case study. The conventional mining method ranked as the most efficient mining method from the four methods considered. The exercise indicates potential for the AHP to be used in the South African platinum mining industry as a tool for selecting optimal layout designs, conduct regular evaluation of the performance of production shafts, or objectively evaluate line managers for promotion. The work described in this paper is part of the methodology used in a current PhD research study at the University of the Witwatersrand. Keywords: Analytic hierarchy process (AHP); multiple criteria decision analysis (MCDA); decision-making; conventional mining, hybrid mining, mechanized mining.

Jan 1, 2008

By B. G. Fordyce, W. B. Parker

A description is given of the methods used in management planning, pit-equipment selection and maintenance operator training, and formal organization of mining personnel.

Jan 1, 1979

By M. B. Algeo, R. H. A. Plaistowe

A method of forecasting the haulage trucks required for a large open-pit operation is described. Emphasis is placed on the effects of changes in planning and on the complexities of a mining operation that involves many benches and dumping areas.

Jan 1, 1979

By A. M. Sage

This paper reviews the metallurgical functions of vanadium in high-strength Iow-alloy steels, and discusses the ways in which vanadium is used in various types of steel supplied as reinforcing bars, plates, sections, and strip. Potential developments to meet new engineering requirements are discussed briefly.

Jan 1, 1984

By N. Gibson

The application of oxygen in a copper smelter by N. GIBSON* (Visitor) This paper describes how the problem of increasing the capacity of the Rokana copper smelter was handled, and how oxygen was found to be technically and economically the best solution. The first phase of its implementation is outlined.

Jan 3, 1974

The 88th Annual General Meeting of The South African Institute of Mining and Metallurgy was held at Kelvin House, Johannesburg, on Wednesday, 14th August, 1985. Mr J.D. Austin (President) was in the chair and declared the meeting open at 16h00.

Jan 1, 1985

By B. K. Loveday

A model for the leaching of non-porous particles by B. K. LOVEDAY*, Ph.D. (Fellow) A model has been developed for the prediction of the rate of leaching for an assemblage of non-porous particles in terms of size-distribution parameters. Expressions are developed for batch and continuous operation, and an example of the application of the model is given.

Jan 9, 1975

By G. E. Blight

The mining industry is making increasing use of pumped tailings fills. The properties that affect the performance of tailings fills are described by means of typical examples. They are the particle-size grading for maximum density, the water content for pumpability, settlement after placing, compression and drainage under stress, shear strength, and resistance to shock loading.

Jan 1, 1979

Mr Philipus Albertus von Wieligh, a former President of the Chamber of Mines and Executive Director of Johannesburg Consolidated Investment Company, died in Johannesburg on Thursday, 28th December, 1989. He is survived by his widow, a daughter, and two grandchildren. Mr Von Wieligh served the mining industry for 45 years. The P.A. von Wieligh Park in Hilshaven on the West Rand is named after him.

Jan 1, 1990

By P. J. Nel, A. Täuber

SYNOPSIS A method is described whereby finely ground glassy granulated blastfurnace slag mixed with small quantities of clay, whiting and quartz has been used for making ceramic tiles in the laboratory. The tiles were semi-dry pressed and devitrification as well as sintering occurred during firing. The properties of the resulting product compared favourably in many respects with ordinary ceramic flooring materials.

The inaugural meeting of the Western Cape Branch of The South African Institute of Mining and Metallurgy was held on Thursday evening, 13th November, 1986, in the Department of Chemical Engineering at the University of Cape Town. Before the meeting, letters had been sent to al the registered SAIMM members in the Western Cape area, informing them of the desire to establish local branch, and inviting them to attend.

Jan 1, 1987

By G. E. Blight

Rates of erosion have been measured for the slopes and top surfaces of a number of gold-tailings dams in the Germiston-Johannesburg-Roodepoort area of the Transvaal. Preliminary results were given in an earlier paper. The present paper gives results for a four-year period of observation, and identifies the major factors affecting the rates of erosion from the surfaces of gold-tailings dams.

Jan 1, 1989

By J. Palarski

Long waling is used in most Polish coal seams, with backfilling to support the roof, to create an artificial hanging wall to prevent movement if the rockmass, and to eliminate the fire hazard in abandoned mine workings. This paper discusses the results if tests conducted on 7 different backfill mixtures, and gives equations for the estimation if the flow if backfill slurries through gravitational pipelines.

Jan 1, 1994

The finite element method of stress analysis is nowadays widely used in the fields of mining, mechanical and civil engineering. This paper presents a short description of the three-dimensional method, in which the elements used are arbitrary hexahedrons. Two examples of the application of the method are presented, namely, calculation of the elastic stress distributions in a coal pillar and in an opencast mine.