Search Documents

By Gift Chisakuta, Bravo Mbao, Nils Schwarz, Angus Feather, Anthony Mukutuma

Bwana Mkubwa is a 50 000 tons per annum copper cathode producer, owned by First Quantum Minerals and located in Ndola, on the Zambian Copperbelt. The Bwana Mkubwa solvent-extraction circuit was started up in 1997. In 2002, the plant began treating ore from First Quantum?s Lonshi mine located in the Democratic Republic of Congo. The Lonshi ore is exceptionally fine and the amount of solids in the feed solution reporting to the solvent-extraction feed solution increased dramatically. Initially, crud was filtered in a filter press, but this rapidly blinded and seldom produced anything better than a wet sludge containing large quantities of organic. In December 2003 the decision was made to install a Flottweg Z4E-3/441 Tricanter® centrifuge to recover organic from the crud. The installation was completed in June 2004 and has since led to significant improvements in plant operability and savings in organic consumption.

Jan 1, 2007

By G. J. McTeer, D. J. Rioux

Teck Metals Ltd operates an integrated zinc-lead complex at Trail, British Columbia, Canada. Since 1997, KIVCETTM flash smelting technology has been utilized for the treatment of zinc plant residues and lead concentrates. Trail Operations’ furnace uses four water-cooled jackets for bullion tapping. This paper provides an overview of KIVCET bullion tapping for the past 16 years, and discusses successes and challenges encountered with respect to operations, training, and monitoring.

Jan 1, 2014

By X. H. Li, Q. Zhang, X. Fei

Bauxite residue known as red mud (RM) is a by-product produced in massive quantities during alumina production by the Bayer process with a utilisation rate of less than 5%. A large amount of RM accumulated and produced continuously has had a seriously adverse impact on the surrounding ecological environment. The application of RM in building materials is considered to be the most effective and thorough way to make RM harmless and recycle resources for the reason that adding RM to concrete as a mineral admixture could not only consume a lot of RM, but also save cement and other energy-consuming industrial products. In this paper, the adaptability to cement and aggregate of RM was studied. The results showed that the compressive strength and flexural strength of concrete using ordinary Portland cement, slag Portland cement or fly ash Portland cement as cementing material showed different trends with the increase of the amount of RM. The influence rules of RM on the compressive strength of Portland cement, slag Portland cement and fly ash Portland cement concrete were similar, whether for silicate aggregate or carbonate aggregate. RM has a negative correlation to the flexural strength of silicate aggregate-ordinary Portland cement concrete, but a positive correlation to silicate aggregate-slag Portland cement, silicate aggregate-fly ash Portland Cement. RM promoted the formation of calcium carbonate crystals and inhibited the formation of ettringite and calcium hydroxide crystals in the matrix while ordinary Portland cement, Portland cement and fly ash Portland cement were used as cementing materials. This study provided support for the use of RM in concrete, the reduction of solid waste storage, and the saving of high energy consumption cement as well. Keywords: Red mud, cement, aggregate, adaptability, mechanical properties, mineral composition

Jan 1, 2020

By C. Nexhip, S. Sun

Critical to understanding and controlling phase mixing and separation in metallurgical processes, is the development of reliable experimental techniques to measure interfacial properties of melt systems. A series of experiments has been carried out to determine the effect of oxygen potential on the surface tension of liquid copper. Using an electromagnetic levitation method, a surface tension-oxygen chemical potential adsorption isotherm was produced for the Cu-O system at T 1400 K. The surface tension results show good agreement with the literature values e.g. within 3 per cent for pure copper. The Belton `ideal' adsorption isotherm was applied, and the following equation derived to best fit the experimental data ? =1251-77.5 1n41+ (2.79x105 . pO1/2)](mN.m Using this equation, the surface tension of copper was calculated/predicted as a function of oxygen potential at 1400 K, and showed excellent agreement with the experimental values. This confirmed that the adsorption behaviour of oxygen in liquid copper is ideal. The saturation coverage of oxygen on the surface of liquid copper was determined to be T0 = 6.65 µmoles.m,-2 corresponding to an area per adsorbed oxygen atom of ao ? 25 Å2. These values agree well with those cited in the literature, and our experimental data cover a very wide range of oxygen potential (10-5 to 10-17 atm). Keywords: levitation melting, surface tension, Cu-O alloys, oxygen potential, adsorption isotherm, surface coverage.

Jan 1, 2004

With increasing demand for real-time monitoring of mine parameters, the requirement for appropriate data management in many mining applications is also increasing. This includes atmospheric monitoring in underground coal and metal mines. Although a number of different (real-time) monitoring systems have been installed in underground mines, they all typically share the same systems or sub-systems, where each sub-system may include both custom hardware and / or software components. In addition, monitoring components installed in underground coal mines in the USA should also be intrinsically safe and approved by the US Mine Safety and Health Administration. Real-time analysis adds complexity to the system since data validation and storage should be completed independently of filtering, data reduction operations, or visualization. Real-time processing may include statistical evaluation, trending, cross-correlation, and real-time alarm or warning generation. This paper presents the concept and design of an integrated system under development for atmospheric monitoring in US coal mines.

Jan 1, 2014

By M. Abdellatif

The Mintek Thermal Magnesium Process (MTMP) process is based on DC open arc metallothermic smelting of calcined dolomite at normal pressure and temperatures of 1650?1750°C. The process was demonstrated at the pilot scale in the period 2000?2004. Major changes to the MTMP pilot plant were made throughout the development period, which lasted for about five years. The changes included design and installation of new equipment, modification of existing equipment, changes in the metallurgical approach in terms of feed rates, feed recipes, furnace operating temperatures, cold and hot dolime feeding, and steady and systematic changes in the operating procedures and maintenance of the plant. As a result, the performance of the pilot plant gradually improved from one campaign to the next, in terms of availability and in particular the condensation efficiency. In Run 10, the process was successfully demonstrated over an 8-day campaign. Keywords Magnesium, condensation efficiency, DC arc furnace, silicothermic reduction.

Jan 1, 2011

By H. Basarir

Due to the environmental constraints and the limitations on blasting, ripping as a ground loosening and breaking method has become more popular in both mining and civil engineering applications. Because of the technological advances in dozer manufacturing techniques, more powerful dozer types are available today. Thus, the ground, previously classified as non-rippable, has become rippable. As a consequence, a more applicable rippability classification system is needed which considers both equipment properties as well as rock properties in all applications. This paper is part of a complementary research work and presents the development of a previously published grading rippability classification system by the application of fuzzy set theory. The integrated rippability classification system considers the combined utilization of the rock and equipment properties, as well as expert opinion. Fuzzy set theory was chosen mainly because it deals well with uncertainty in the choice of variables. Although there are apparent sharp or discontinuous boundaries in existing classification systems, practically most of the factors involved in the ripping process are less well defined and boundaries are more blurred (or fuzzy) or uncertain in nature. Also by means of fuzzy logic it is possible to eliminate bias or subjectivity. The validity of the proposed system was checked by the comparison against existing classification systems and direct ripping production values obtained at studied sites. It is seen that by means of fuzzy logic, the uncertainties are reduced and biased usage of the final ratings that appear in alternative systems are efficiently dealt with. Keywords: Fuzzy set theory, rock rippability, rippability classification system, direct ripping, fuzzy inference system.

Jan 1, 2007

By R. Xie, J. Liu, Y. Zhu, Y. Li

The surface chemistry features of spodumene and feldspar were investigated by XPS, zeta potential measurements and first principle calculation. The results indicated that the zeta potential of feldspar was more negative than that of spodumene. The most possible active sites on spodumene and feldspar were Al sites and O sites. However, the number, type and activity of these sites were different. The flotation behaviour of five new collectors (cationic collector decyloxy-propyl-amine (DPA), anionic collector α-bromododecanoic acid (α-BDDA), N-Dodecyliminodiacetic acid (DIDA), and mixed collector DPA-BDDA and DPA-DIDA) were investigated through micro flotation experiments and analysed based on the surface chemistry features of spodumene and feldspar. The results revealed that cationic collector DPA processed a high collecting capacity for both minerals. The highest recovery of spodumene and feldspar was 91.60% and 95.30% respectively. The anionic collector α-BDDA and DIDA showed poor flotation behaviour. The recovery of spodumene and feldspar when using α-BDDA as collector was less than 5% and when using DIDA as collector was less than 1%. For the mixed collector DPA-BDDA, the recovery of spodumene and feldspar was 82.27% and 32.61% respectively at pH 4.5. For mixed collector DPA-DIDA, the recovery of spodumene and feldspar was 35.69% and 9.08% respectively at pH 5.8. The results indicated that the cationic collector had high collecting capacity, but low selectivity. The collecting capacity of anionic collector for spodumene and feldspar was poor at the same concentration compared with cationic collectors. Mixed collector DPA-BDDA showed good flotation behaviour and selectivity on spodumene. The ―COO- in mixed collector might improve the selectivity. However, too much ―COO- would increase the electrostatic repulsion, which might cause low selectively and poor recovery. Keywords: Spodumene, feldspar, surface chemistry features, mixed collector, flotation

Jan 1, 2020

By J. N. Baloyi

"In atomic emission and atomic absorption spectrophotometry, the sample is heated to a high temperature and thereby decomposed into atoms and ions that absorb or emit visible or ultraviolet electromagnetic radiation at energies characteristic of the elements involved. The flame test is a very simple form of this technique. The yellowing of a flame by the addition of salt, for example, occurs because the sodium in salt emits strongly in the yellow portion of the visible spectrum. These methods are especially useful for low concentrations of metallic elements in both qualitative and quantitative analysis.Interference on Iep-OES has not always been considered a serious problem, especially in the beginning, when compared with Atomic Absorption Spectroscopy. This was due to the euphoria created by the new technique. It meant that criticism was subdued. The Iep was vastly superior to the Atomic Absorption technique, that the interferences suffered by the Atomic Absorption technique dwarfed the little interferences suffered by the rep-OES technique. This is how rep-OES has had a reputation as an interference free technique."

Jan 1, 2014

By A. E. Lewis, J. Du Plessis, J. Chivavava

Current metallurgical processes lack selective and efficient REE recovery from aqueous leach liquors. Antisolvent crystallisation is used to selectively recover pure inorganic salts from aqueous solutions without excessive chemical use in ambient conditions. Yttrium sulfate octahydrate (Y2(SO4)3.8H2O) was used as a representative rare earth salt to investigate the effect of antisolvent selection on the crystal morphology and size distribution of the final crystalline product produced through antisolvent crystallisation. The antisolvents of choice were short length alcohols that are water miscible i.e. methanol, ethanol, 2-propanol and t-butanol. All experimental parameters except the type of antisolvent were kept constant under isothermal conditions. The large reduction in solubility of the salt by the antisolvent creates high supersaturations. This leads to high product yields as observed in this study at > 91%. In general, a variety of morphologies were successfully formed in each individual alcohol including; rods, plates, prismatic cubes and starburst clusters. The powder X-ray diffraction (XRD) analysis indicated that Y2(SO4)3.8H2O was the only species present for all final products. There was a change observed from the starburst and rod structures for the shorter alcohols towards prismatic cubes for the longer alcohols due to different strengths in the solute-antisolvent interaction at the crystal growth faces. The crystal sizes increased with an increase in the alcohol chain length because of the lower supersaturation conditions due to a limit in the mass transfer induced by the bulkier alcohol structure. In conclusion, it has been shown that the particle morphology and size can be greatly affected by the selection of antisolvent even under high supersaturation conditions, contributing to understanding the effect of different antisolvents on the final particle characteristics. The engineering of favoured product characteristics can therefore be achieved by antisolvent crystallisation, presenting a viable alternative process for the recovery of REE. Keywords: Antisolvent crystallisation, rare earth elements, morphology, particle size

Jan 1, 2020

The influence of varying amounts of magnesia, silica, and alumina in iron ore sinter on its mineralogy, reducibility index (RI), reduction disintegration index (RDI), physical breakdown (AI and TI), and production properties (coke breeze rate) were examined. It was found that the mineralogy of iron sinter can more easily be predicted from its chemical composition than from the RI, RDI, AI or TI. Anticipating the consequence that varying amounts of MgO and SiO2would have on sinter properties is complex, and not necessarily predictable. High concentrations of Al2O3in the sinter result in high concentrations of the SFCA phase, but with drastically deteriorated properties. This study also confirmed that the form in which fluxes are added to the raw material sinter mixture affects the mineralogy and properties of the produced sinter.

Jan 1, 2010

By C. E. More

Some observations on 'ancient' mining at Phalaborwa C. E. MORE. B.A. (Pretoria) (Visitor) A brief account is given of historical references to the Phalaborwa area, the first being to the mountain of copper and iron sought by Francois de Cuiper in 1725. These are followed by a description of several finds in the area, which are related to finds described in the literature and to Bantu tradition on the subject. Phalaborwa is one of the earliest known mining sites in the Republic of South Africa, Loolekop having been a mining centre, as shown by carbon-14 dating, since 770 A.D.

Jan 1, 1974

By J J. McEwan

Silver tarnishes readily in common atmospheres and is accelerated in humid atmospheres. Tarnish is the formation of silver sulphide on the surface of silver when it is exposed to a wide range of sulphur-containing atmospheres. Tarnish is unattractive and highly undesirable, and can be removed either with a silver polish or a chemical dip. Dips are generally only recommended when heavy black tarnish cannot be removed with a polish, and care must be taken during cleaning because these can contain aggressive chemicals and give off hazardous and unpleasant smelling fumes. Polishes work best for large areas of plain undecorated silver, and form part of a regular cleaning programme. Some polishes contain chemicals that inhibit tarnishing, but these generally only have a short life. Several methods have been developed to reduce tarnish formation on Silver; these include alloying, surface treatment, and coatings. The authors evaluated a range of self-assembled monolayer (SAM) surface treatments and coatings in earlier research. Four treatments/coatings increased the time to noticeable tarnish by more than ten fold, and the results were reported at the International Corrosion Congress (ICC) in 2005, and at the Mint Directors Conference (MDC) in 2006. SAM treatment using 95% 1-hexadecanethiol (C16H34S) was found to give good anti-tarnish performance and showed potential for the commercial treatment of Sterling silver. Therefore research was performed to optimise the methods of application of this type of coating to provide an easier, faster, and more-user friendly technique to provide an anti-tarnish treatment. Keywords: silver, tarnish resistant coatings.

Jan 1, 2006

By M. Magnelöv, Du Sichen, U. Sjöström

An experimental study has been performed to investigate the behaviour and separation of inclusions at the interface between steel and slag. The study has been limited to liquid inclusions because they can be a potential problem in transient situations such as ladle changes in continuous casting of steel. Model experiments with water and silicon oils have been carried out to study the kinetics of separation of simulated inclusions at an interface. The properties of the inclusions and the slags have been varied by using different oils with different viscosities, densities and surface tensions. The effect of temperature of the liquids has also been examined. Measurements of the terminal velocity, rest time and the behaviour of the liquid inclusions at the interface have been recorded using a video camera. It has been found that the inclusions reach their terminal velocity early in the vessel and the experimental velocities differ somewhat from the values evaluated using ?intermediate law?. The results from the experiments have shown that the size of the inclusions has no appreciable influence on the rest time. Droplets of AK50 oil have been found to have considerably long rest time. A water film surrounding the droplet has been expected to be the main reason for the long rest time. The present study has also shown that the viscosity of the oil has certain effect on the rest time, but only to some extent, since viscosity has double functions. A higher viscosity provides higher resistance to the droplet entering the oil phase leading to longer rest time and at the same time damps the lateral movement of the droplet along the interface, leading to easier stabilization and shorter rest time. On the other hand, a high viscosity of the oil phase results in slow dissolution process. It has been concluded that a meaningful model of inclusion separation at the metal-slag interface must take the interfacial phenomena into consideration. Keywords: Inclusions, terminal velocity, rest time, dissolution.

Jan 1, 2004

By Ö. Erdem

The investment decision making process in the insurance and finance industries is affected by new advances such as simulation techniques. These advances have improved the discounted cash flow method (DCF). In DCF, a dynamic and flexible model construction is not possible because it does not consider uncertain conditions. Each project should be evaluated taking into account the related uncertainties because the related uncertainties determine the characterization of the project. Related uncertainties can be processed in dynamic DCF, which is applicable to both financial and non-financial industries with different kind of uncertainties, such as power generation and petroleum projects. The dynamic DCF method can estimate net present value (NPV) while managing related project uncertainties with a simulation method like Monte Carlo Simulation. The simulation method is preferred because its output is unbiased. Therefore, a more realistic financial evaluation of the project can be concluded. In spite of the improvement of dynamic DCF, this project evaluation method is not used frequently in mining industry. However, the mining industry is ideally suited to this concept because it is highly dependent on estimations such as orebody size and ore grade. During the project evaluation stage, these uncertainties can be included with the dynamic DCF method. This study aims to contribute to increasing the usage of this method in mining projects. A copper reserve in Turkey is selected as a case study to apply uncertainty assessment for the evaluation of NPV.

Jan 1, 2012

By J. H. Dalton

The paper reviews the effects of fast-neutron irradiation on the tensile properties of austenitic stainless steels at irradiation temperatures of less than 400°C, using, as an example, work carried out at Pelindaba on an AISI 316 type steel produced in South Africa. Damage produced in these steels at higher irradiation temperatures and fluences is also briefly discussed. The paper concludes with a discussion of some methods of overcoming or decreasing the effects of irradiation damage.

Jan 1, 1979

By J. Petersen, T. Moyo, J. Dinga

The leaching of chalcopyrite in ferric sulfate media is notorious for its slow and inhibited kinetics. Different methods have been proposed to improve the kinetics, including the use of organic compounds as additives to the leaching media. In this study, the enhancing effect of methanol, ethanol, 1-propanol, and 2-propanol on the leaching of chalcopyrite in aerated acid ferric sulfate solutions using different reactor systems was investigated. The results revealed a clear improvement of copper dissolution by methanol and 1-propanol relative to tests with no additives under similar conditions. Operating a continuous-flow mini-column reactor yields surprisingly good results, potentially related to the maintaining of a consistent leaching micro-environment on the mineral surface. Scanning electron microscopy studies showed that the alcohols result in the removal of surface deposits formed during the anodic dissolution, potentially thus facilitating improved cathodic reduction of the ferric ion to drive the anodic dissolution.

Jan 1, 2023

By J. C. Vreugdenburg, B. A. Dippenaar, J. Muller, T. L. de Vries

Iron ore fines are agglomerated to produce sinter, which is an important feed material for blast furnaces worldwide. A model of the iron ore sintering process has been developed with the objective of being representative of the sinter pot test, the standard laboratory process in which the behaviour of specific sinter feed mixtures is evaluated. The model aims to predict sinter quality, including chemical quality and physical strength, as well as key sinter process performance parameters such as production rate and fuel consumption rate. The model uses the finite difference method (FDM) to solve heat and mass distributions within the sinter pot over the height and time dimensions. This model can further be used for establishing empirical relationships between modelled parameters and measured sinter properties. Inputs into the model include the feed material physical properties, chemical compositions, and boundary conditions. Submodels describe relationships between applied pressure differential and gas flow rate through the bed of granulated fine ore particles, combustion of carbonaceous material, calcination of fluxes, evaporation and condensation of water, and melting and solidification. The model was applied to typical sinter test conditions to illustrate the results predicted, and to test sensitivities to parameters such as feed void fraction, feed coke percentage, and the fraction of combustion heat transferred to the gas phase. A model validation and improvement study should follow, ensuring sinter test results are free from experimental errors by conducting repeated tests.

Jan 1, 2015

By J. Danoczi

Specially designed X-ray machines are used extensively on diamond mines for the recovery of diamonds from ores. These machines are extremely expensive and, at present, there are no reliable methods of determining if the equipment is performing efficiently. The objective of this work was to manufacture translucent X-ray diamond simulants, which would emit varying but known luminescence signals when exposed to X-rays. These X-ray diamond simulants could then be used to determine the efficiency of diamond recovery operations.

Jan 1, 2008

By B. P. Watson, A. Carpede, W. O. Kekana, N. Fernandes, W. Theron, M. P. Mahlangu, G. Betz

The research described in this paper was done to confirm the Upper Group 2 (UG2) PlatMine peak pillar strength formula (Watson et al., 2007), which was determined from a back-analysis of failed and unfailed pillars. Underground measurements were made on a stable pillar that was loaded by firstly reducing it’s length and then by mining the surrounding pillars until pillar failure took place. The pillar was instrumented with suitably positioned strain cells and closure meters, which allowed both the average pillar stress and strain to be determined. The paper describes the methodology applied to identify a suitable position for the instrumentation, as well as the results. A stress/strain curve is presented for a UG2 pillar with a w/h ratio of 2.0, at Booysendal Platinum Mine. The measured pillar strength was similar to the predicted strength using the PlatMine pillar strength formula for UG2 pillars. The PlatMine formula has been successfully implemented on Booysendal Platinum Mine, and about 3 670 pillars have been cut without a single failure. An additional revenue of US$1.3 billion was calculated for the 25-year life of the mine as a direct result of the improved pillar design, given the January 2020 platinum group metals basket price. An extended life of mine and better mining efficiencies will also be realized.

Aug 1, 2021