Search Documents

By Thomas V. Fame, William E. Porter

"As geological and mining conditions become more complex, and as overall mining economics become more marginal, short- and long-range decision-making regarding multiple-seam surface mining becomes more difficult. The decision-making problem involves a study of economics, cut-off grades and ratios, equipment capabilities, sequencing and selective mining practices.This paper is concerned primarily with multiple-seam mining of bituminous coal. The research has led to the development of an economic decision-making model for use as a day-to-day tool to aid mine operators and pit geologists to decide what and how to mine.The model is designed as an aid for feasibility decision-making in multiple-scam situations and for situations where selective mining is needed or desired. In effect, a simulation of the feasibility and preliminary mine planning phases has been developed. The model is divided into four separate segments: decision-making, simulated mining, cost calculations and the determination of the discounted cash flow return on investment."

Jan 1, 2014

By R. E. Wilmot

This paper is based on the experiences, over many years, on the part of numerous authors in the South African mining industry and that of the hot dip galvanizing process and its application as a corrosion protection system. The paper sets out the extensive development, financial resources and stringent operating requirements of the South African mining industry. After many years of research and operational experiences, hot dip galvanizing and when necessary, duplex systems, have been found to meet the demanding requirements of this particular industry. The paper sets out the requirements from the standpoint of corrosion criteria and is followed with a practical example; ?case history? where the corrosion protection properties of hot dip galvanizing are demonstrated. This case history traces the early investigation of the expected corrosive conditions to be encountered in a new mining operation (now 10 years on) and concludes with two follow up visits to the mine in order to examine actual performance of the corrosion protection system after ten years in service.

Jan 1, 2006

By V. Labiouse, M. Jaboyedoff

GIS documents are of great interest for a quick and low-cost determination of areas endangered by rockfalls. They allow (i) the detection of potential instabilities from steep slopes and cliff areas, and (ii) the preliminary estimation of potential run-out areas by means of a so-called cone method. After the presentation of the tools used to compute these areas, the paper focuses on two methods developed for a preliminary hazard mapping, one at regional scale and the other at local scale. Mittels GIS-Dokumenten können von Steinschlag bedrohte Gebiete schnell und kostengünstig ermittelt werden. Die sogenannte Kegelmethode erlaubt die Erkennung potentiell instabiler Zonen von Steilhängen und Felswänden sowie eine erste Einschätzung der möglichen Reichweiten. Nach der Vorstellung der zur Berechnung der bedrohten Gebiete benötigten Hilfsmittel stellt der Artikel zwei Methoden zur vorläufigen Gefahrenkartierung in lokalem und regionalem Maßstab vor. Les SIG sont très intéressants pour une détermination rapide et peu onéreuse des zones affectées par des chutes de blocs. Ils permettent une détection des zones potentiellement instables et une estimation sommaire des zones de propagation des blocs par une méthode dite des cônes. Après la description des outils utilisés pour définir ces zones, l’article expose deux méthodologies élaborées pour un zonage préliminaire du danger, l’une à l’échelle régionale et l’autre à l’échelle locale.

Jan 1, 2003

By R. Trammell, O. Eterigho-Ikelegbe, S. O. Bada

In response to the enormous amounts of coal discard generated during coal mining and preparation, the development of an efficient and sustainable strategic use of this resource is essential. Furthermore, the rising urban population over the next decades is confronted with the depletion of quality raw materials for building components. To this end, this study reports new information on the morphology, water absorption, and flexural strength properties of ceramic composites produced from three different coal discards and polysiloxane pre-ceramic polymer (PCP) resin. In addition, test results relating to the continuous operating temperature, chemical resistance, and efflorescence potential of the composites are presented. The results show that the water absorption and flexural strength of the coal composites, up to 1.94% and 36.46 MPa respectively, exceed the requirements for ceramic and clay roof tiles. The continuous operating temperature of composites is found to be more thermally stable than conventional roofing tiles (concrete and ceramic) between ambient temperature and 600°C. In addition, the excellent chemical resistance of the composites (94.43%−99.98%) compared to conventional roofing tiles (67.82%−99.97%) eliminates the need for additional external coatings. The interesting results documented so far suggest that this technique could be used to produce low-temperature application building products such as bricks, panels, roofing tiles, etc. This new recycling technique offers an excellent opportunity to eliminate enormous volumes of coal discard and to advance the circular economy in the coal industry.

Aug 2, 2022

By L. Mabiza

Keywords: Pyrometallurgy, circular furnace, PGM, platinum, Peirce-Smith converter, Zimbabwe The Zimplats Smelter, located on the northern part of the Great Dyke, at the Selous Metallurgical Complex, is the only PGM smelter in Zimbabwe. Zimplats? operations currently consist of the Ngezi Platinum Mine, which is a 1.5 Mt/a open-cast and 0.7 Mt/a underground mine, and a Concentrator and Smelter to which ore is transported 80 km by road. The final converter matte product is transported to Impala Refining Services in South Africa for refining and marketing. The Zimplats Smelter operations consist of a concentrate filtration plant, a Drytech flash dryer, a modified Elkem / Hatch 13.5 MVA circular furnace, two 10? x 15? Peirce-Smith converters, and a matte granulation plant. The Zimplats smelter uses a three-field electrostatic precipitator, supplied by ELB-Brandt, for removal of particulates in the gas streams from both the converter and furnace. Construction of the smelter commenced in 1995, under the BHP / Delta Gold of Australia joint venture. The furnace was lined mid-1996, and smelting operations commenced in 1997. Due to design challenges, the Elkem furnace was modified by Hatch in 1998, and the smelter had not reached full capacity when operations were suspended in 1999. Re-commissioning took place in January 2002.

Jan 1, 2006

By R. D. Hull

Paper written on project work carried out in partial fulfilment of B.Sc. (Eng.) (Mining) degree As a partial fulfilment for the degree of B.Sc. (Eng) (mining) at the University of the Witwatersrand, a dissertation was to be completed in the mining industry. This was done at Finsch mine, with the purpose of determining the best solution to the required secondary breaking problem. In order to complete the study of the secondary blasting method available for use in the new block 4, cave mining method at Finsch mine the following problem statement was identified and solved ?The methods currently in use, for the secondary breaking of oversize rocks at their source in the current production levels, are to be investigated, and their applicability to the new block 4mining project determined?. To effectively achieve this problem statement above; time was spent researching and investigating, in depth, the methods that are currently in use at both Finsch and Koffiefontein mines; so as to gain practical knowledge of these. The methods were identified and independently evaluated, taking into consideration factors such as costs of the equipment, time to break oversize rocks, advantages, disadvantages, safety and labour requirements, etc. This in turn then allowed for a direct comparison between the methods and the decision as to the best to apply to the new block 4 production level. The methods that were investigated included: ?Concussion blasting, where concussion bombs and lay-on charges are used to break hang-ups and boulders. ?Drill and blast methods, where holes are drilled in large rocks and charged manually with explosives. ?Emulsion secondary blasting, which is a new project in use at Koffiefontein mine from African Explosives Limited. ?The Ro-BustTM breaking system, a hydro-fracturing breaking system. Once all the methods had been evaluated and compared it was found that the Ro-BustTM Breaking system was the most applicable for the breaking of boulders, with, the Emulsion Blasting System being used for hang-ups. Further information and the more in-depth version of this report, is stored in the resource centre at De Beers?Finsch Mineand the School of Mining Engineering WITS University.`

Jan 1, 2002

By F. H. Cornet, D. Ask, O. Stephansson

We have conducted a stress analysis of overcoring stress measurements undertaken at the Zedex Test Site (ZTS) in the Äspö HRL, Sweden. Two different types of overcoring cells have been used at the site: the 9-gauge Borre Probe (CSIR-type) and the 12-gauge CSIRO HI cell. Inversion programs based on the least-squares criterion were developed and calibrated. The primary and secondary stress field in the ZTS were back-calculated using strain data from individual cells as well as from combining data from both cells. We propose that the combination of strain data from the two cells significantly improves the determination of the stress field. A striking result is the good agreement between the re-analysed overcoring data and the existing hydraulic fracturing data. The deviations for the horizontal stresses between the re-analyzed overcoring data and the existing hydraulic fracturing data are approximately 3 MPa. The deviation in the orientation of maximum horizontal stress is approximately 10-20°. Nous avons analysé les résultats de mesures de contrainte par surcarottage réalisées sur le site Zedex, du laboratoire souterrain HRL d’Aspö, en suède. Deux types de cellule de mesure ont été utilisés sur ce site : la cellule à 9 jauges (du type CSIR) et la cellule à 12 jauges (du type CSIRO HI). Un programme d’inversion mettant en œuvre une norme par moindres carrés a été développé et validé. Les champs de contrainte primaires et secondaires du site Zedex ont été évalués d’une part en considérant chaque mesure isolément, d’autre part en intégrant l’ensemble des données de déformation dans une inversion unique. Nos résultats suggèrent que l‘association des diverses mesures dans une intégration unique améliore nettement la détermination du champ de contrainte. Un résultat intéressant est le bon accord entre ces nouveaux résultats et les résultats des mesures par fracturation hydraulique. Les écarts sur l’amplitude des contraintes horizontales est de l’ordre de 3 Mpa, les écarts sur les orientations de l’ordre de 10-20°. Auf dem Zedex Test Gelände im Äspö Festgesteinslabor (HRL) wurde eine Spannungsanalyse mittels Overcoring Spannungsmessungen durchgeführt. Hierzu wurden zwei verschiedene Methoden verwendet: das 9-kanal Borre Gerät (CSIR- Ausführung) und die 12-Kanal CSIRO HI Zelle. Inversionsprogramme, die auf dem “least-squares”- Kriterium basieren, wurden entwickelt und kalibriert. Das primäre und sekundäre Spannungsfeld des Zedex Test Geländes wurde sowohl aus Verformungsdaten individueller Zellen als auch aus Kombination beider Zellen ermittelt. Wir nehmen an, daß die Kombination der Messergebnisse beider Geräte die Bestimmung des Spannungsfeldes signifikant verbessert. Überzeugender Beweis hierfür ist die gute Übereinstimmung der überprüften Overcoring Daten und Ergebnisse aus existierenden Hydraulic Fracturing Versuchen. Die Abweichungen der horizontalen Spannungen aus beiden Datensätzen ist etwa 3 MPa und Abweichungen der Orientierung der größten Horizontalspannung liegen bei etwa 10-20°.

Jan 1, 2003

By A. F. Spinks, S. P. Nicholls

"The Lower Orebody at Chingola Division of Nchanga Consolidated Copper Mines, Limited, is a stratified orebody that is mined by a continuous caving system. The accurate determination of the developed and semi-developed ore reserves has always been difficult. The new system proposed in 1971 is designed to update and, as new informa¬tion becomes available, to account for the depletion of, the reserves.There are three main inputs to the system. These are borehole data, survey data and extractions data. The borehole data are input to a geological borehole master file system, which holds every recorded detail of a borehole in an easily extractable form. These data can be extracted for ore reserve calculations or for contour mapping of orebodies and rock types. The grades for use in the ore reserve calculations are extracted from the relevant boreholes.The survey data are information on the position of the blocks and drifts, taken from plans, and information on the scraper drift and trough drive positions taken from sections. The information is extracted from the plans and sections using a D Mac pencil follower. The ore reserve is calculated from the survey data and the borehole data.Data on extractions are taken from scraper operators' logs, tramming records, skips hoisted records and accepted mill tonnages and grades. Using these data, the mill tonnages are reconciled back to the drifts, to deplete the current ore reserves.As new workings are brought into operation and further evaluation holes are drilled, the relevant data are input and the new developed ore reserve is calculated."

Jan 1, 2014

This is an abstract from Environmental Service and Technology (Vol 32 No 20 1998) which will be o finterest to South African Mining and Metallurgical Scientists, involved in chromium mining and Metallurgical processing. Maybe the scourge of our dams and reservoirs?the water hyacinth can be put to good use! The novel technology of phytoremediation embraces plant accumulation processes for the cleanup of toxic heavy metals and organic chemicals. Several plant species have been identified that are excellent hyperaccumulators of a number of heavy metals, e.g., Brassica juncea (Indian mustard) and Thlaspe caerulescens (Alpine pennycress). Other speciesincluding Myriophyllum brasiliense(Parrot?s feather), Salixsp. (willow), and Popullussp. (poplar) have also demonstrated phytoremediating abilities.

Jan 1, 1999

By C Katongo

Ground condition at No1. Shaft varies across the mine. The different ground conditions arise as a result of the differences in the rock strength and structure, seismicity and induced stresses in abutments areas. Apart from being a major cause of Fall of Ground incidents/accidents, adverse ground conditions where encountered has affected the rate of development advance as well as production. This implies that for support to be cost effective Geotechnical section has to ensure that support is designed to prevailing ground demand to ensure the safety of personnel and minimize loss of production. We have also seen changes in mining methods as a result of change in ground conditions. To avoid incurring unnecessary costs through remedial works resulting from ground deterioration and collapses of development openings due to inadequate support, the principle in engineering design is ?Do it right the First Time?, and this can only be achieved through good understanding of Geotechnical environment. The paper discusses the different ground conditions encountered in various development ends at No.1 Shaft. It also discusses the principles of ground support, failure mechanisms, types of ground support systems employed, and the different techniques used to select support systems, and quality control techniques in underground support installation.

Jan 1, 2005

By Van Sint JanM., M. Prudencio

ABSTRACT We report the results of a model-testing program to evaluate the strength characteristics of non-persistent joints. We describe the conditions under which new tensile cracks generate and propagate to connect existing joints so that the rock mass becomes fractured into several blocks, leading to a low strength. The strength of some models was equal to that along a single joint through the full sample length. In models with two joint sets, failure took place along a composite plane, partly sliding along a discontinuous joint and shearing through the intervening intact block of rock, or else by rotation and sliding of the blocks. This last failure mode could also lead to very low model strength. ZUSAMMENFASSUNG Dieser Bericht beschreibt die Ergebnisse von Versuchen mit Modellfelsmassen um den Einfluâ von unterbrochenen Rissen in ihrer Widerstandsfähigkeit zu untersuchen. Es werden die Umstände beschrieben unter denen neue Zugrisse entstehen, sich verbreiten, sich mit bestehenden Rissen verbinden und die Felsmasse in mehrere Felsblöcke zerlegen und zu einer kleinen Widerstandsfestigkeit führen. Der Widerstand einiger Versuchskörper entsprach der Festigkeit eines Risses der die ganze Länge des Versuchskörpers überquert.Versuchkörper mit zwei Rißfamilien versagten unter einer zusammegesetzten Ebene, zum Teil mit Verschiebungen nach unterbrochenen Rißebenen die sich durch Schnittversagen intakter Felsblöcke verbinden, und zum Teil durch Drehungen und Verschiebungen einzelner Felsblöcke. Die letzte Versagunsart kann zu einer stark verminderten Widerstansfähigkeit führen. RÉSUMÉ Nous présentons les résultats de quelques essais fait sur des modèles évaluant les caractéristiques de résistance des fractures discontinues. Nous décrivons les conditions sous lesquelles des nouvelles fissures de traction peuvent s’engendrer et se propager pour faire la connection avec des fractures existantes, de façon que le rocher se fracture en plusieurs blocs, menant à une résistance réduite. La résistance de quelques modèles fut égale a celle d’une fracture traversant toute la longueur du modèle. Pour les modèles ayant deux ensembles de fractures, la rupture a eu lieu sur une surface mixte, causée d’une part, par le glissement sur une fracture discontinue et d’autre part, par la rupture à travers le pont de matériel intact; ou bien par rotation et glissement des blocs. Cette dernière façon de rupture peut aussi aboutir à une très faible résistance des modèles.

Jan 1, 2003

By M. Reuter, C. Schuffeneger, T. Seppälä, L. Holappa

Reaction kinetics of solid-state reduction of chromite pellets (laboratory made and industrial) and lumpy ore was investigated by the thermogravimetric analysis (TGA) technique. Carbon monoxide was used as the reducing agent, with the presence of graphite in proximity to chromite. The experiments were carried out at both rising temperature and constant temperature in the range of 1450 - 1550°C. Scanning electron microscopy was employed to observe and analyse the structure and composition changes of the chromite samples. For the lab-made chromite pellets, the effects of particle size and bentonite addition on the reduction behaviour were studied. The pellet with smaller particle size gave a higher reduction rate. Bentonite addition had slightly negative effect on the reduction rate. When reducing industrial pellets, temperature and CO flow rate had positive influence on the reduction rate. Reduction of lumpy ore took place slower than reduction of a pellet. In all samples, chromite reduction proceeded longer in the outer part of the sample than in the centre part. The porosity of the chromite samples was determined before and after the experiments. The porosity of lumpy chromite increased significantly during the reduction. However, the porosity of lab-made chromite pellet decreases due to sintering effect. The reaction mechanism is discussed on the basis of experimental results and earlier investigations.

Jan 1, 2004

By J. Saunders, N. Pretorius, G. Krafft, T. P. Katakwa

Imagine being able to see all the future planned mining activities in real time. This is exactly what SIMS (Short Interval Management System) will enable you to do. SIMS is a real time short interval control system that continuously measures and sets optimised plans for mining production processes. The system utilises algorithm-based software that takes resources (people, equipment, tasks, and workplaces) and gives you the best achievable plan. The algorithm was developed using methods found in the field of metaheuristics. A metaheuristic is a strategy to designed to efficiently search for optimal or near optimal solutions to problems that are very complex computationally. (Glover, 1986) There are several algorithms that have been developed to solve optimisation problems which are difficult to solve using traditional techniques. This has given rise to a field called evolutionary computing. (Simon, 2013) Examples of these techniques are genetic algorithms, particle swarm optimisation, and ant colony optimisation. These methods are used to solve problems in a variety of fields. As an example, Kok and Lane (2012) used particle swarm optimisation for equipment allocation in a mechanised underground mining environment. The first SIMS deployment took place in a platinum underground tabular mechanised mine near Burgersfort (province?) from 2017-2019. This included the development from a paper-based system to a fully operational online system. SIMS then moved to a second site and is currently being tested in a second platinum underground tabular mechanised mine in South Africa. Full deployment of the system is currently being phased in. SIMS was built in response to issues that have been plaguing the mining industry for years. These issues are all aligned into one major problem statement: how can we optimise mining production processes without compromising safety? This product was developed by combining years of mining experience with software development. SIMS is based on a four-pillar concept. Safety, productivity, accountability, and business improvement. SIMS uses a set of pre-configured mining and production rules, and with the resources that are available, to determine valid short term production plans. A background algorithm then determines the optimum plan to be executed. The system continuously produces a set of job cards that are pushed to respective operators on their allocated tablets. The management portal component allows you to view and manage all current and planned work on any connected device available. This allows real time visibility of completed, current, and planned work to operators, service departments and management, i.e., seeing into the future.

Sep 1, 2021

By B. Leong, H. Joubert

Keywords: Pyrometallurgy, furnace, auxiliary equipment, copper slag launders Pyromet has designed copper launders for tapping slag. What makes Pyromet?s launder design innovative and safe is that it does not have any cooling water channels underneath the launder runner, whilst achieving effective cooling of the runner. If matte burn-throughs were to occur through the launder runner, the risk of damaging water channels and the risk of explosions are reduced. In addition, since the cooling water channels are not harmed, the launder is easily repairable and reusable. Pyromet makes use of Finite Element Analysis to optimize the launder geometry to ensure that sufficient energy is removed from the centre of the launder. Factors considered during the launder design include the suitability of the geometry to the client?s needs, experience from existing installations, and ease of fabrication. Pyromet goes so far as to develop procedures for fabricators to ensure that fabrication issues do not compromise the functionality of the launder. When launder orders are received by Pyromet, the entire fabrication process and the functioning of the launders during operations are monitored to ensure that the launder designs are continuously improving with every installation.

Jan 1, 2006

By C. M. Rule, A. K. Anyimadu, L. Knopjes

Ongoing development work on ultra-fine grinding for various applications at the Group?s concentrators has been conducted by Anglo Platinum over the last few years. Current potential applications for mainstream grinding and concentrate grinding are the subject of a group-wide research and development programme. The first 10 000-litre 2.6 MW IsaMill was jointly developed by Anglo Platinum, Xstrata Technology and Netszch for installation at the Western Limb Tailings Re-treatment project in Rustenburg, South Africa. The unit was commissioned in late 2003/early 2004, and has operated in an intermediate concentrate regrind application successfully since. This paper describes the operational performance to date, as compared with the original duty specifications and objectives. The first mainstream M10 000 IsaMill with a 3 MW drive will be operational in November2006 at the Potgietersrus Platinum (PPL) ?Platreef? Sandsloot Concentrator in South Africa?s Limpopo Province. Key Words: Western Limb Tailings Re-treatment Plant, IsaMilling, Platreef, Platinum, Palladium, PGMs, tailings.

Jan 1, 2006

Assuming that a gold ore has been effectively ground to ensure maximum economic liberation of gold, the circuits that will have the most effect on the successful operation of a gold plant will be that of the leaching and carbon-in-pulp circuit (CIP). The reagent and utilities operating costs associated with leaching, adsorption, elution and regeneration would typically make up some 15% of total operating cost, whilst the capital costs associated with these areas is about 16% of the total. Although not largest (capital and operating costs associated with comminution are generally dominant) these items represent a significant proportion of capital and operating cost. Much more importantly, these plant areas represent the primary gold recovery process and their technical and operational efficiencies will have a significant impact on overall plant efficiency. The objective during process design of these sections is thus to develop a design which provides maximum technical and economic efficiency and which is robust to potential changes in ore throughput, mineralogical characteristics and head-grade. Experience has shown that, particularly for longer life and higher-grade projects typical of the South African underground gold mining industry, small changes in recovery and efficiency have a significant value over the life of the project.

Jan 1, 1999

By Y. He

Early research showed that the separation of particles based upon their density was not possible in steadily rising air streams. The terminal velocities of moving spheres are determined by their aerodynamic characteristics. This prevents particle separation by density in standard air classifiers. Passive pulsing air classifiers have accelerated airflow in certain regions, which achieves density-dominant separation. Numerical simulation of airflow within passive pulsing air classifiers was done to estimate airflow patterns near a damper. Analysis of those results shows the significant acceleration of the airflow above the damper. Laboratory trial separations have shown that passive pulsing classifiers are superior to standard air classifiers. Keywords: pulsing airflow, passive, simulation of airflow models, acceleration effect, density

Jan 1, 2005

By B. C. Viljoen

"SynopsisCommencement of the next phase of the Lesotho Highlands Water Project is a year or so away from becoming reality. Some 50 km of tunnels in the form of access adits, shafts, diversion tunnels, and main waterways will be constructed. Sprayed concrete will form an integral part of the temporary and permanent rock support systems that will be installed. Furthermore, the use of sprayed concrete as a final tunnel lining solution was proposed as a viable alternative to concrete linings in the feasibility studies that preceded the forthcoming implementation phase.The aim of this paper is to make the reader aware of all the sprayed concrete related issues that engineers tend to grapple with during the design and construction of tunnel projects and other underground works. Primarily, these issues would include selection of applicable design parameters, technical specifications, construction application methods, quality control and, most importantly in the context of final or permanent linings, the durability of sprayed concrete.The International Tunnelling Association (ITA) Working Group (WG) 12 has been tasked specifically to publish a set of recommendations on the Quality and Control of the Application of Sprayed Concrete and the Testing of Sprayed Concrete for Durability. These tasks were also further explored at the recent World Tunnel Congress (WTC 2015) that was held in Dubrovnik, Croatia at the end of May 2015.IntroductionSprayed concrete is presented in a variety of shapes, designs, forms, application methods and accompanying terminologies including shotcrete, gunite, pneumatically applied concrete, and the like. The International Tunnelling Association (ITA) decided to standardize on a single terminology, namely ‘sprayed concrete’, in order to simplify specification, interpretation of guidelines, and codes of practice."

Jan 1, 2015

By P. A. Lilly, W. Sarunic

In most cases, slope movement monitoring data are collected on a temporal basis and displacement or velocity is plotted against time in order to assist the engineer to make judgements about slope behaviour. Once an unusual behaviour pattern has been established, the data are then analysed to estimate when the key inflection points occur in the data, when the slope movements start to accelerate and, ultimately, when the slope is expected to collapse. The identification of these inflection points is sometimes difficult to achieve with the naked eye. This paper presents the application of a trend analysis technique, known as cusums, to assist in this process. The authors have presented a range of data from various real life examples which highlight the effectiveness of the cusums technique. A key aspect of the cusums technique is the use of a constant (K) against which data trends are assessed. This constant is best derived from slope performance data at each site, as each rock mass will behave in its own unique way. The authors have experienced slopes that have had threshold values ranging from 0.1mm/day through to 10mm/day, and therefore a conservative approach should be adopted when assessing the performance of slopes.

Jan 1, 2006

By R. K. W. Merkle, F. A. S. Reyneke, Z. Harris, P. W. J. Delport

The technological advancements in computing power in the last 30 years have enabled the practical visualization of complex geological environments in three-dimensional (3D) space. 3D models and their application in the mining industry are becoming increasingly important, for example, to identify future exploration areas and targets, for mineral assessment and evaluation, and prediction and planning of future drill-holes. However, acquiring borehole data is an expensive practice, with drilling programmes costing mining companies up to billions of dollars each year. Tighter financial constraints on exploration budgets result in more pressure being put on three-dimensional models to accurately identify future target areas. This article aims to evaluate the potential drilling success of simulated greenfield and brownfield exploration using a 3D geological model created of Leeuwpoort tin mine. These simulations investigate the probability of intersecting a mineralized zone of economic interest and evaluate how the probability is affected when the number of drill-holes and distance from a known intersection changes. Furthermore, these simulations attempt to obtain an indication for the minimum number of drill-holes required for a successful exploration campaign at the mine. The investigation also aims to establish a first-pass attempt towards developing a ‘favoured procedure’ for identifying potential exploration targets for tin deposits with geological and geochemical characteristics similar to Leeuwpoort. The results for the ‘favoured procedure’ established are statistically tested using the ‘bootstrapping’ method. By simulating various exploration scenarios, the study also emphasises the importance of predicting successful drilling, which aids in budgeting for drilling programmes as the minimum number of drillholes needed for a specific exploration project can be determined.

Feb 2, 2022