Search Documents

By Ali Sogue, Steven Schurman, R. Jensen

This paper presents the results of the remediation of the Gregory Gulch #1 Superfund site, an EPA Clear Creek Superfund project located in central Colorado. The Gregory Gulch #1 site was an historic gold mine and mill located within the city limits of Central City, Colorado. Remediation efforts included the use of the Envirobond™ additive to chemically bind the metals in 3,000 tons of acid generating mine waste that contained high levels of arsenic, lead, zinc and mercury. The toxicity of the mine waste amended with Envirobond™ was not only reduced to RCRA TCLP standards but also to the more stringent UTS standards. The final cost of the treatment was much less than standard industry solidification processes and significantly less than offsite disposal options.

Jan 1, 1999

By G. Gaidajis

Sea water samples collected from coastal waters in the vicinity of the Stratoni mining operations, in North-Aegean Sea were analysed for dissolved metals and elements. The maximum concentrations observed were one to three orders of magnitude lower than the environmental limit which coincides with the quality of sea waters suitable for swimming purposes. The quality of the coastal sea waters are affected by the natural mineralization of the area and the urban activities drained through local small rivers, the past mining activities present in the sea bottom sediments in the form of disposed tailings, and finally by the presence of the adjacent Mill-Flotation Plant. The relative importance of the treated final effluents discharged from the mining operations is considered to be insignificant.

Jan 1, 2006

By James W. Furlow

A recent attempt by a major mining company to mine phosphate in Chatham County, Georgia, resulted in a study by the Georgia Department of Mines, Mining and Geology which was intended to evaluate the deposit as well as potential hazards to the major fresh-water aquifer of the area. The study found that the confining layer above the fresh-water artesian aquifer is sufficiently thick and impermeable to allow removal of the phosphate ore zone without significant salt water infiltration into the aquifer. Therefore, phosphate mining under proper supervision will not adversely affect the quality of water used by the city of Savannah nearby. Volumetric studies show that there is a minimum of 4,800,000,000 cubic yards of phosphate matrix containing an average of 22.5% BPL. At an approximate weight of 1.5 tons per cubic yard and a concentration of 22.5% BPL, there are about 1.6 billion tons of 100% BPL concentrate present. At a conservative factor of 50% at least 800,000,000 tons of 100% BPL concentrate could be recovered for market sale. In addition to the area discussed, evidence indicates that the phosphate horizon-may extend continuously out to sea for at least ten miles, and probably beyond.

Jan 1, 1972

By V. Nemec

The paper deals with further progress of the space and time models achieved since some of the previous APCOM symposia (1970, 1975, 1980) where original methodology was presented. Various transformations, de- and retectonization of space models, transfer of patterns, interactive time models are among the most important improvements. Enlarged possibilities of practical applications of the developed system are shown.

Jan 1, 1986

By Paul E. Senseny

Data from triaxial compression tests per- formed at confining pressures between 0 and 100 MPa are used to evaluate parameters in a contitutive model that is based on microcracking. The tensorial formulation is reduced to equations that are specific to the simple Loading imposed in triaxial compression tests. Procedures for evaluating the model parameters are described, dependence of parameter values on confining pressure is discussed, and prediction of failure is assessed.

Jan 1, 1986

By Lee Herold Storey

Groundwater remediation is growing in occurrence in the western United States. Groundwater remediation programs are regulated by state water quality statutes. The remedial action plans implemented under these statutes may conflict with well-established existing rights to withdraw groundwater for beneficial use. This paper discusses how the states of Arizona, Colorado and New Mexico administer conflicts between the need to withdraw and remediate groundwater with the existing rights of others to withdraw groundwater for beneficial purposes.

Jan 1, 1991

By M. G. Hester, G. S. Adisoma

To address the problem of grade estimation in a general three-dimensional shape and the uncertainty associated with the estimate, the technique of jackknifing/ block-kriging shortcut is proposed. A new estimator called jackknife kriging is introduced first. Through the jackknife variance, a confidence limit for the reserve-grade estimate can be calculated. Unlike the kriging variance, which is more a measure of data configuration and which is independent of data values, the jackknife variance reflects the true variability of the data. This approach provides a simple way to set a confidence level for global estimation of resources.

Jan 1, 1997

By K. Rajamani, L. B. Hales

Much of the process control effort in the mineral industry uses proportional-integral-derivative controllers that require periodic retuning. Retuning hundreds of controllers typically employed in a single plant is a formidable task for the control engineer. Adaptive controllers offer an alternative to this problem, since they are designed to tune themselves. Four schemes of adaptive control-gain scheduling, model reference adaptive control, self-tuning regulator, and optimal adaptive controllers-are discussed with process examples. The control of a ball mill circuit with a multivariable self-tuning regulator is illustrated. This controller encompasses the advantages of the other three controllers and is applicable for a wide range of process variability.

Jan 1, 1988

By S. K. Singh, J. Shepherd

Feather-edging, a major source of injury and fatal accidents in Australia, South Africa and the United States, refers to a phenomenon in which the roof at the goaf edge falls, often suddenly, as a thin wafer of rock that overrides conventional timber breaker lines. The fall may adversely affect a working bord at a distance of 15 m (50ft) or more from the goaf edge. Feather-edging typically occurs in relatively massive, strong roof strata such as sandstone or conglomerate. This paper presents the results of a test in which a concentrated row of fully grouted bolts were used to prevent feather-edging in an Australian pillar- ("total-") extraction coal mine. The test demonstrated that the bolts could resist feather-edging.

Jan 1, 2000

By S. Tavani, R. E. Browner, R. Dunne

Lead is used in CIP/CIL circuit to increase the leaching rate of gold from ores. At least four mechanisms have been proposed for the action of lead in gold leaching circuits: (I) precipitation of sulphides as highly insoluble lead sulphides preventing consumption of cyanide and oxygen; (2) su,face reaction on sulphide particles forming an insoluble lead sulphide layer peventing dissolution of those sulphides; ( 3) precipitation of lead sulphide, which undergoes further oxidation to soluble lead sulphate recycling the lead to solution,· ( 4) contact reduction of lead onto the gold szaface which then acts as a secondary oxidising agent. Rotating disc studies using a pure gold disc show that small amounts (5ppm) of sulphide ions are sufficient to significantly reduce the leaching rate of gold. Lead increased the leaching rate at small concentrations but at higher levels decreased the rate of leaching. The detrimental effects of lead were only found for a pure solution when leaching the gold disc. Ores mediate the amount of lead available by ads01ption/reaction, thus, reduced leaching rates from excess lead are not serious even when 500ppm of lead ions are added to the sluny. The detrimental effects of sulphide ions could be countered by lead addition during the leaching process. A penalty, in the form of reduced leaching rate, will occur the longer lead addition is delayed. A time lag was noted between the addition of lead and the increased leaching rate when a large concentration of sulphide ions was present.

Jan 1, 2000

By Mark Gershon

This paper describes an application of a new approach to mine planning and production scheduling in a gold mine. The technique, limited to use in open pit mines (but not limited to gold), has been described previously (Gershon, 1987). The-computer program used is the HOPS software, which has been described previously as well (Gershon, 1988). The mine is scheduled for the production of 8,000 blocks out of a mine having 25,000 blocks (50 x 50 x 10). The technique is based on the concept of inverted cones (Gershon, 1987). While it does not provide a true optimization of results, it does approximate the optimal situation. As opposed to most scheduling software that only serves as a computerized notepad for the scheduler, the use of this approach allows for a scheduling intelligence to be built into the software.

Jan 1, 1989

By Dewey W. Marino

Conventional remote sensing applications for the exploration of natural resources has largely been the domain of low resolu­tion Earth orbiting systems such as Landsat™ which can sample a broad range of the spectrum. As the classic application of remote sensing, it has proven its worth through the discovery of numerous mineral deposits worldwide. Often this technique relies more on the spectral content of the imagery for narrowing potential sites on the ground, but often cannot reveal the detailed context of the observed response. As the dawn of the new era in remote sensing grows closer, high-resolution imagery is proving its worth for the definition of mineral potential and its cost sav­ing advantages for mine management.

Jan 1, 1998

By Gordon P. Riddler

IMMM Reporting Code 2001 – Some Developments -General definition of a Competent Person -Rules of Conduct with Guidelines -Table of Generic Terms with Guidelines -More specific to non-metallic minerals -Word ‘ore’ is not used for reserve/resource categories -More definitive on Mineral Exploration Results

Jan 1, 2003

By L. Alan Weakly

Page one is missing from book

Jan 1, 1982

By C. H. Bucknam, A. M. Raichur, M. Misra

Simultaneous dissolution of mercury along with gold occurs during cyanidation of gold ores. A method has been found for the efficient removal of mercury from the gold cyanide solution by treating with dithiocarbamates which form stable compounds with mercury. The mercury concentration in the leach solution can be brought down to low levels by adopting this treatment. Furthermore, it is also possible to stabilize the mercury in the ore heap itself by addition of this reagent so that mercury does not dissolve in the cyanide solution during heap leaching. Only trace amounts of mercury were detected in the pregnant solution obtained from a heap treated with dithiocarbamates. In this paper, process parameters are discussed in detail.

Jan 1, 1997

By J. A. Herbst

Introduction The ability to evaluate the improvement resulting from the implementation of an automatic control system is essential to the Justification of its cost. This evaluation may occur after anew control system has been commissioned. In other cases an existing plant which is operated manually may be automated only In part in order to determine In ether the met of it should be. Finally. in some instances dynamic isolation my be used prior to installation of the control system to determine the strategy to be used or to evaluate the improvements In process performance expected from automatic control. This paper describes the development of a methodology for making these evaluations. In order to obtain an accurate assessment of Improvements In a short time, statistical methods can be employed. Mineral processing plant, are subjected to many types of both random and deterministic disturbances of various duration. The statistical method, available for process control at analysis are designed to counter the obscuring effects that random disturbances have on such as evaluation. The basis for evaluation and comparison is some freely chosen measures of process performance termed the performance index or objective function. The experimental data used to calculate the performance index should, if possible, be collected by alternately running a circuit Or plant with the two or more type, or control being tested ("serial testing”) or more preferably, by running two circuits with the two type, of control side by side ("parallel testing") . The performance index is a random variable so that when comparing two types of control, statistical hypothesis testing must be used. By testing s hypothesis statistically one accept, or reject, a (null) hypothesis [ ] concerning the mean or variance of one or more performance indices. For example, a hypothesis Ho might be that the mean of a performance index with stabilizing control is larger than with manual control. Defining a Performance Index The performance index, denoted by [ ] , is a measure by which alternative strategies or situations my be cam peered on either s technical or an economic basis (see Table 1). Technical measures are concerned with the effects of control on process variables or outputs or on the deviations of controlled variable, from their setpoints. For commotion circuit, important technical measures of performance are throughput, product fineness and the consumption of liners, media and electrical energy. For flotation circuits important technical .satires are recovery, grade and reagent consumption. Economic measure such a, cost and profit n usually determined from a combination of technical measures and are usually the final factor upon which a decision may be made, although a control system my achieve higher values of technical measure , the control effort expended my be of such magnitude that the economic measures, such as cost, are poor. Running Comparisons Comparison, between automatic and manual control are normally done with data obtained before and after control system Installation, unless ore characteristics remain the same during the period of data collection the results will be biased. By running the test circuit with the control system alternately turned on and curled off until all possible ore type, have been run through the circuit, unbiased result, can be obtained. This mode of testing is termed “serial testing.” An alternative and potentially more powerful and quicker made of testing is "parallel testing" in which two circuits, one with the type of control being tested and one without, arm run aide by side. In this type of testing both circuits process the same ore so that valid results occur sooner than with aerial testing. The data may be averaged before testing or the differences in the performance indices may first be calculated before averaging. However, the two circuits must be nearly identical in their mechanical characteristics otherwise differences other than the degree of control will bias the results. It mechanical differences exist than it my be necessary to adjust one or the circuits prior to testing. Sometimes it is possible to correct far mechanical differences based on Inherent efficiency calculations made with a model. Hypothesis Testing Once the data is collected, hypothesis fencing can be carried out to determine if the automatic control system has resulted in a statistically significant improvement. One can construct a histogram of the distribution or performance indices with am without control such as Figure 1, or the

Jan 1, 1991

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this work was to assess the influence of parameters such as residence time, solid content, and temperature in a process route towards purified rare earth liquor which could be adequate to produce marketable rare earth products. The steps of the process route proposed in this study comprised water leaching of a sulfated rare earth ore and removal of impurities through the purification of the rare earth sulfuric liquor, which is the product of the water leaching step. The sample used in the water leaching experiments was a sulfated rare earth ore produced by the reaction of a beneficiated rare earth ore with sulfuric acid followed by roasting at 700 °C for 2 h in a muffle furnace and cooling at 20 °C. The water leaching experiments showed that the best condition comprised a residence time of 30 min, temperature of 20 °C, and solid content of 10% w/w, resulting in a recovery of 71.3% of the rare earth elements (REE) and a lower impurity extraction, e.g., only 15.0% of Fe, representing the main impurity in the rare earth ore. Even when presenting low amounts of impurities, the rare earth sulfuric liquor still needed to be purified before it can be used in the production of marketable rare earth products. In the study, the rare earth sulfuric liquors were purified in two consecutive neutralization steps, first by dosing the limestone pulp to pH up to 3.5 and secondly by adding the lime pulp to raise the pH from 3.5 to 5.0. The application of two consecutive purification steps at 20 °C resulted in the highest overall REE recoveries (65.4%) throughout all the steps of the process, being 71.3% in the water leaching, 99.6% in the partial purification with limestone pulp, and 92.1% in the purification with lime pulp at 20 °C. Under this condition, there was a total elimination of Fe, P, and Th and a significant reduction in the Al, U, and sulfate concentrations in the purified rare earth liquor. The purified rare earth liquor attained through the experiment is expected to be amenable to be used in the production of marketable products due to the lower impurities/REO mass ratios.

By Robert C. Freas

Lime, the versatile chemical is, generally speaking, a calcined or burned form of limestone commonly known as quicklime, calcium oxide or, when water is added, calcium hydroxide or slaked lime. Almost 40 different lime products are available, a fact which has contributed to the rather loose use of the term lime as well as to confusion and misunderstanding. The term is frequently, albeit erroneously, used to denote almost any kind of calcareous material or finely ground form of limestone or dolomite. Lime is made from high calcium or high magnesium limestone, generally having a minimum of 97% combined carbonate content. Normally, high calcium lime has less than 5% MgO. When the lime is produced from a high magnesium limestone, the product is referred to as dolomitic lime. Calcination/Hydration Calcination, or the production of lime, has its origins in the earliest days of alchemy, with the general reaction class having been identified in an Arabic text printed in 1000 AD. It was much later, however, in the mid-1700s to the mid-1800s before this basic reaction became understood from scientific perspective. The pro- duction of lime has been so basic and simple that its underlying scientific principles have over the years received only intermittent investigation. Rather, much of the thought and inquiry has been directed toward the development of kilns. Thus, it has only been in the last 25 to 30 years that lime has received any concentrated scientific investigation relative to the thermodynamics and kinetics of the calcination and hydration reactions. Particular emphasis has been focused upon energy consumption and fuel efficiency. Calcination refers to a broad class of reactions, of which the limeflimestone reaction is just one, wherein a substance is heated to less than its melting point, resulting is a weight gain or weight loss. In the calcination of limestone to produce lime, the basic chemical reaction is as follows: [ ] While there is nearly universal agreement bout the equilibrium conditions related to the limestone/lime reaction above, there have been numerous and varied calcination models developed for the reaction. Recent investigations have resulted in the development of the model shown in [Fig. 1]. From this model it can be seen that calcination is a function of both temperature and CO, pressure. It does not, however, provide any indication of the rate at which the reaction takes place. Calcination is strongly time variant with different limestones. In a very broad sense this relates to the fact that the calcination reaction starts on the exterior surface of the limestone and then proceeds toward the center. As the calcination reaction takes place, the CO2 released at the interface must make its way through the lime to the exterior surface. Since calcination is limited by gas diffusion to the surface of the partially calcined limestone, the natural impurities in the stone, differences in crystallinity, grain boundary chemistry, density variations, and imperfections in the atomic lattice all play a significant role in calcination rate. Therefore, the suitability of a given limestone as a source material for lime production can be determined only after completion of adequate burn tests designed to evaluate the various limiting factors. When a coal-fired kiln system is considered, the entire process of calcination is made even more complex by the introduction of additional chemical constituents into the calcination environment. The reader is referred to the references for a more detailed description of the complete calcination reaction and the differences inherent between differing kiln systems. In the foregoing discussion it was noted that CO2 is released during the reaction. This release results in a 44% weight loss during the complete calcination of a high calcium limestone, or a 48% weight loss for a highly dolomitic limestone. The trade term for this weight percent loss is loss on ignition, or LOI. This weight loss is frequently used as a measure of the completeness of calcination. Because the calcination reaction is chemically reversible, quicklime or burned lime is frequently referred to a being highly reactive, or unstable. The more stable form of lime, hydrated lime, is commonly preferred and generally specified by the user. Hydrated lime is obtained by adding water to quicklime to produce a dry, fine powder. Quicklime's affinity for moisture is then satisfied, although it still retains a strong affinity for CO2.

Jan 1, 1994

By W. R. Dengler

INTRODUCTION Shaft sinking represents a relatively small proportion of the activities involved in mine development. Because of this limited utilization, shaft sinking has been one of the most difficult functions to mechanize. Although shaft machines (muckers) were introduced more than 30 years ago, the first machines were low-capacity units, and machines of this type did not gain wide acceptance by the mining industry until the late 1950s. However, the increasing depth of underground mines and the es¬calating costs of labor have increased the benefits obtain¬able from high-speed shaft sinking. The result has been a growing need for high-capacity shaft machines. Most of the machines available at the present time have been developed by modifying existing equipment to increase the payload capacity and performance. AVAILABLE SHAFT MACHINES In general, shaft machines may be classified accord¬ing to the types of digging mechanisms and the mecha¬nisms of operation. The available digging mechanisms include clamshells, cactus grabs, front-end buckets, and backhoes. The mechanisms of operation can be classified as either pneumatic or hydraulic. Selection Criteria For efficient operation, the primary consideration in selecting a shaft machine is its capacity. The minimum capacity of the machine should match the capacity of the hoisting system at the ultimate depth of the shaft. In many cases, two machines may be needed to obtain a sufficient mucking capacity. The shaft dimensions and configuration often dictate the type of machine that may be utilized; for example, an overshot loader does not work well in a circular shaft that has a diameter of less than 5.5 m (18 ft). Similarly, a single Cryderman mucker is not suitable for a large-diameter shaft, nor is it applicable where very high sinking buckets are to be used. Other factors for consideration include the degree of material fragmentation, the abrasiveness of the rock, and the amount of ground water that is inter¬sected. Machine Descriptions Riddell Mucker: The Riddell mucker, illustrated in Fig. 1, was first introduced in 1948. This is one of the most common shaft machines in the medium-capacity range. The Riddell mucker consists of a hoisting and traveling mechanism that operates a clamshell suspended on cables. The early machines operated with a 0.3 m3 (10 cu ft) clamshell and had an hourly capacity of approximately 27 t (30 st). This type of shaft machine has gained wide acceptance throughout North America. Essentially, the Riddell mucker consists of standard components, such as the pneumatic tugger hoists that operate the clamshell. The carriage is suspended on rails that also serve as the blasting set, located immediately below the shaft timbers. To effectively position the clam¬shell in the shaft, the operator controls the carriage travel by means of wheels that are driven by a pneu¬matic motor. The Riddell mucker most commonly is used in rec¬tangular timbered shafts. However, some units have been installed with circular rails, allowing them to work in circular concrete-lined shafts. A popular practice with many Riddell muckers is to increase the capacity through the use of larger clamshells, often ranging up to 0.76 m3 (1.0 cu yd), in conjunction with more powerful tugger hoists. In some large rectangular shafts, two Riddell units have been used side by side to achieve a sufficient capacity. Cryderman Mucker: The Cryderman mucker, illus¬trated in Fig. 2, is another common shaft machine in the low- to medium-capacity range. Developed in the early 1950s, it also has gained wide acceptance throughout North America. Equipped with a 0.3 m3 (10 cu ft) bucket, the Cryderman mucker has an hourly capacity of approximately 23 t (25 st). The Cryderman mucker is operated entirely by means of pneumatic cylinders and a pneumatic telescopic boom. The boom is suspended from a sectional frame¬work that is usually located at one end of the shaft. The framework or headframe can be suspended from an independent hoisting system located either on the sur¬face or in the shaft. In large shafts of either rectangular

Jan 1, 1982

By R. K. Zipf

Recent scientific studies by researchers at the National Institute for Occupational Safety and Health (NIOSH) and the U.S. Army Corps of Engineers (USACE) presented the worst-case explosion pressures that can develop if a methane-air mixture of a certain composition and dimension accumulates and ignites within a sealed area of a mine. The Mine Safety and Health Administration (MSHA) issued its final rule on sealing of abandoned areas which considers potential explosion pressures and the risk of achieving the necessary conditions. The new MSHA seals regulation has increased the pressure design criteria an order of magnitude beyond the old standard of 140 kPa (20 psi) to 800 kPa (120 psi). However, there still are major knowledge gaps pertaining to seals and sealed areas including: (1) the composition of the sealed area atmosphere and how it changes in time and space, (2) explosion pressures that might actually develop within sealed areas, (3) engineering procedures to follow when designing seals and seal installations, and (4) guidelines to manage the atmosphere within sealed areas with monitoring or inertization. NIOSH has initiated a seals research program with collaborators from Safety in Mines Testing and Research Station (SIMTARS) in Australia, West Virginia University (WVU), the Naval Research Laboratory (NRL), and USACE. Highlights of progress so far include: (1) construction of a gas explosion tube at Lake Lynn Laboratory for studying large methane-air explosions, (2) computer simulation of the fluid dynamics of high pressure methane-air explosions, (3) development of seal analysis methods considering construction materials, reinforcement and the seal foundation, and (4) development and testing of innovative seal designs that utilize inexpensive, readily-available rock rubble to resist high explosion pressures. NIOSH researchers aim to provide sound engineering guidelines to better address the new MSHA seal regulations. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009