Search Documents

By J. H. Rowland, A. C. Smith, K. A. Teacoach

Current regulations for fire suppression systems in underground coal mines to protect conveyor belt installations have been in place since the Coal Mine Health and Safety Act of 1969 was enacted. Over time, the coal conveyer equipment being used and ventilation conditions underground have changed significantly, particularly the width of the conveyor belts and the use of belt air at the face. The effect of these new conditions on the effectiveness of suppression systems during a fire is not known. The National Institute of Occupational Safety and Health (NIOSH) conducted a study to evaluate the effect of air velocity, water sprinkler activation temperature and a limited water application time on the effectiveness of water sprinkler fire suppression systems to extinguish large-scale conveyor belt fires. The fire tests were conducted using both new and used 1.8-m-wide, fire-resistant rubber belt that met the Mine Safety and Health Administration (MSHA) flame-resistant requirement specified in Title 30, Code of Federal Regulations, part 18, section 18.65 (also known as the 2G test). Tests were conducted using standard response sprinklers with activation temperatures of 68° C and 141° C at air velocities of 0.5 and 5.1 m/s. Two tests were conducted at both air velocities for each sprinkler activation temperature, one using a new belt and one with a used belt. The results showed that the suppression system was able to suppress the fires in ten minutes to the point that a miner could extinguish it with a fire hose. However, in several of the tests, the fire reestablished itself a few minutes after the sprinkler water supply was cut off and quickly grew out of control. This report discusses the large-scale experimental configuration, the installation specifications of the fire suppression system and the results and conclusions regarding the effect of air velocity, sprinkler activation temperature and limited water application on the suppression system performance.

Jan 1, 2010

By Rong Guo, Qi He, Jinsuo Zhang

"Coal mine ranks No.1 among the 6 major high-risk industries, so it is no doubt that the senior managers in the coal mine bear more stress than other industry executives. The massive working stress results in serious influences on the physical and mental health of the senior managers of coal mine, which might also induce the safety risk in the coal mine. Therefore, to evaluate the senior managers’ working stress and put forward strategies of mitigating the stress is of great theoretical and practical significance in improving the physical and mental health of the senior managers and reducing the safety risk in the coal mine. The research on the working stress has been made in the western countries for almost 50 years, China began the research in the mid and late 1990s, the research is spread across multiple industries including education, medical treatment, computer and aviation. However, there is little research on the senior managers’ working stress of the coal mine, so the available literatures are few. In the paper, we, based on the working stress model of Robbins and through questionnaire survey, analyze the element composition of the senior managers’ working stress of the coal mine; then, we construct the evaluation indicator system of the senior managers’ working stress of the coal mine based on the individual factor, organization factor and environment factor; after that, we determine weights of each evaluation indicators by using the improved triangular fuzzy number weight method, and set up the evaluation model of the senior managers’ working stress of the coal mine on the basis of the fuzzy comprehensive assessment method. At last, in accordance with the model, we evaluate and analyze the working stress for the senior managers of some typical coal mines, and diagnoses the major sources and intensities of the senior managers’ working stress, and then propose corresponding strategies of mitigating the stress."

Jan 1, 2017

By Hilal Soydan, H. Sebnem Düzgün, Jurgen Brune

In this study, with the primary goal of capturing ongoing digital transformation and automation impacts on the mining industry and its workforce, we conduct several interviews with mining industry experts in the United States and analyze our survey reports qualitatively and quantitatively through exploratory analysis. After the interpretation of the insights of industry experts, we proceed to generate a personalized and customized data analysis through a novel metric based on skills, knowledge, competencies and occupational requirements, which quantifies the job similarities for occupations in the mining industry based on the publicly available database of the U.S. Department of Labor. We use text analytics to tokenize and classify the interviews to capture a better understanding of major response categories. The temporal analysis shows that the critical competency needs in the data science and autonomy category increases from 28 percent in current demands to 43 percent. In defining our metric, we also calculate Kullback–Leibler (KL) divergence for each job profile that enables determining whether and to what extent that job is transitionary in our test set based on the mean, standard deviation and kurtosis of each job of interest. Our analysis reveals that the in-group job transitions are significantly easier than the between-group transitions, proving our initial assumptions and common sense. The generated heat maps provide the opportunity to present the gap between the current job and desired job profiles that provide feasible career change options, among others, offering individualized career paths for job seekers and promoting potential job transitions. Through the collection of industry-specific individual employee data, the AI system is envisaged to continue to learn as end users engage with the system, thus creating a central data hub specifically for the future workforce in the mining industry. Although the study has limitations on generalizability for qualitative assessments, it presents itself as a valuable application of how qualitative and quantitative approaches could be of value for future worker training in the mining sector.

Feb 1, 2025

By Chee S. Theng

As the 2016 president of the Society for Mining, Metallurgy & Exploration Inc., I am pleased to present the 2016 issue of the Transactions of the Society for Mining, Metallurgy & Exploration Inc., Vol. 340. A significant portion of the contribution that we make as a professional society is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable the transfer of technology. Communication within the mining community is the key to a successful society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of the American Institute of Mining, Metallurgical and Petroleum Engineers (AIME). Those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2016 Transactions contains some of the most interesting research and insights from the past year and features an international slate of authors spanning industry, academia and government. Papers include the latest findings from the U.S. National Institute for Occupational Safety and Health (NIOSH) and special-issue articles on process development testing. The 2016 Transactions consists of a total of 65 technical papers, encompassing all 21 papers published in 2016 in the Technical Papers Section of Mining Engineering (Vol. 68) and all 27 papers published in 2016 in Minerals & Metallurgical Processing (Vol. 33). Additionally, this volume contains 17 papers that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All of the technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our publications staff. As the 2016 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2016

By R. J. Matetic

The impact of longwall mining on the local hydrological regime has become an important environmental focal point. Unfortunately, only a few studies have addressed the timing and range of well fluid level fluctuations and the associated ground movement. Furthermore, even fewer studies have determined the influence of longwall mining on water quality. The U.S. Bureau of Mines is providing insight into this environmental concern through a program of field case studies. One such study was conducted in Cambria County, PA where five observation water wells were drilled above two adjacent longwall panels. In this study, three wells were completed as nested piezometers and the remaining two served as producing wells. The piezometers were positioned along a line oriented subparallel to the longwall face and were located at the centerline of each panel and over the intervening chain pillars. The piezometers were designed to monitor fluid level fluctuations in both shallow and deep water-bearing zones. Slug tests were conducted before and after mining to characterize changes in hydraulic conductivity of the respective water-bearing zones. Pressure transducers and data loggers were installed to provide continuous fluid level fluctuation data as mining developed through the study area. The producing wells were drilled to provide water quality information. One well was located directly above the centerline of a panel and the other was positioned over the panel's set-up rooms. The wells were designed to simulate domestic use and were produced daily, for four hour intervals, throughout the study. Samples of the produced water were collected before and after mining progressed through the area. In addition, an array of monuments was installed near the study wells and was periodically surveyed to characterize mining-induced surface deformations. This study shows that: a) the observed changes in ground water chemistry did not affect the potability of the water; b) short-term major water level fluctuations occur at the approximate time of undermining; and c) water level recovery begins before the process of subsidence is complete.

Jan 1, 1986

By Marco Aurelio Piangatelli, Massimiliano Bringiotti, Ferdinando De Angelis

"The construction of the three connecting tunnels between the east side and the west side of station C13, adjacent to the Vistula river, has a long and complex history, as they cross beneath one of Warsaw’s main road arteries (Wislostrada). After the attempt to excavate the first tunnel, the face of the tunnel collapsed on the night of August 13, 2012, and a volume of about 10,000 cubic meters of liquid mass (water, silty soil and sand) entered and flooded the west side of the station, which was filled with more than seven meters of material. Fortunately, the workers managed to escape, but machines and equipment were lost. This is the story of how the tunnels were completed, by adopting soil improvement, jet grouting, GRP bars, ground freezing and a careful choice of work steps. INTRODUCTION The Centrum Nauki Kopernik station on Line II of the Warsaw Underground is located alongside to the Vistula river (Figure 1). This station hereinafter is referred to as station C13.The station consist of three parts: the east and west part, and three connecting tunnels 40 meters in length with a large cross section (170 m2).. It includes the rails along the sides and the platform along the centre. The reason for the underground connection of two shafts with a tunnel is due to the presence of a road tunnel (Wislostrada, hereinafter called WS), which must be underpassed by the new metro line (Figure 2).The existing tunnel (Wislostrada) was built many years before, between diaphragm walls, and some foundation structures interfere with the underground tunnel. The challenge was to build the connectors without stopping the traffic of vehicles along the highway above. All works took place in very difficult geological and groundwater conditions due to the presence of Vistula alluvial deposits with poor mechanical characteristics. The soil profile consists of relatively loose sands on top, and silts overlying high plasticity Pliocene clays highly disturbed by the effects of the repeated over-sliding of glacial moraine deposits."

Jan 1, 2016

By John S. Egbert

Many of you are familiar with the Washington Metro Project. However, inasmuch as some may not be, and others may want to refresh their memories regarding certain facets of the project, I will cite a few summary details about the rail transit system we are constructing. That summary will also give each of us a common point for departure as I develop the principal thoughts that I want to leave with you. The Washington Metropolitan Area Transit Authority (WMATA) is an interstate agency established by Compact between the District of Columbia, Maryland and Virginia and approved by the United States Congress. Currently, the Authority has approval to build and operate a 101-mile (162.5 km) regional rapid rail transit system as shown on Appendix A. Of that total, 38 miles (61.2 km) will be in D. C., 32 miles (51.5 km) in Maryland and 30 miles (48.3 km) in Virginia. (Mileage figures, because of rounding error, do not add to 101 miles.) Referring again to the 101-mile total, 48 miles (77.2 km) will be underground, 42 miles (67.6 km) on the surface and 10 miles (16.1 km) on aerial structures. Of the 48 miles (77.2 km) that are underground, 15 miles (24.1 km) are rock tunnel, 14 miles (22.5 km) are earth tunnel, 0.5 miles (0.8 km) 9.s sunken tube and 19 miles (30.6 inn) are cut-and-cover construction. The system will include 86 stations, with 51 of them underground. Referring again to the full 86 stations, 43 will be in D. C., 23 in Maryland and 20 in Virginia. We currently have 37 miles (59.5 km) of line and 41 stations in operations as shown on Appendix B. Also shown on Appendix B is another 16 mile (25.7 km) increment and 13 stations which have been substantially completed, but are not yet in service. Additionally,

Jan 1, 1981

By Barnaby J. Watten, Sibrell. Philip L., Brian J. Vinci, Andrew E. Friedrich

We evaluated a new process for remediation of acid rock drainage (ARD). The process treats ARD with intermittently fluidized beds of granular limestone maintained within a continuous flow reactor pressurized with CO2. Tests were performed over a thirty day period at the Toby Creek mine drainage treatment plant, Elk County, Pennsylvania in cooperation with the Pennsylvania Department of Environmental Protection. Equipment performance was established at operating pressures of 0,34,82, and 117 kPa using an ARD flow of 227 L/min. The ARD had the following characteristics: pH, 3.1; temperature, 10 OC; dissolved oxygen, 6.4 mg/L; acidity, 260 mg/5; total iron, 21 mg/L; aluminum, 22 mg/L; manganese, 7.5 mg/L; and conductivity, 1400 uS/cm. In all cases tested, processed ARD was net alkaline with mean pH and alkalinities of 6.7 and 59 mg/L at a CO2 pressure of 0 kPa, 6.6 and 158 mg/L at 34 kPa, 7.4 and 240 mg/L at 82 kPa, and 7.4 and 290 mg/L at 117 kPa Processed ARD alkalinities were correlated to the settled bed depth (p<0.001) and CO2 pressure (p<0.001). Iron, aluminum, and manganese removal efficiencies of 96%, 99%, and 5%, respectively, were achieved with filtration following treatment. No indications of metal hydroxide precipitation or armoring of the limestone were observed. The surplus alkalinity established at 82 kPa was successful in treating an equivalent of 1136 L/min (fivefold dilution) of the combined three ARD streams entering the Toby Creek Plant. This side-stream capability provides savings in treatment unit scale as well as flexibility in treatment effect. The capability of the system to handle higher influent acidity was tested by elevating the acidity to 5000 mg/L with sulfuric acid. Net alkaline effluent was produced, indicating applicability of the process to highly acidic ARD.

Jan 1, 2000

By John T. Awald

The efficiency of search for porphyry copper and molybdenum deposits can be greatly increased. A model exploration system is here presented to show how geologic literature data and field surveys can be aided by modern statistical and computer methods. Assuming that major ore deposits occur in clusters, it is possible to evaluate rapidly large areas at modest cost and with minimum investment risk. An example of the success of these methods is given. Clusters of mine density and metal production covering the State of Nevada were plotted and machine contoured. Selection of a 47,300 square-mile area on the Nevada-California border was made. Within this area, detailed analyses were performed, and a 3000 square-mile site was picked for subsequent field examination. To initiate efficiently the field work, 81 stream sediment geochemical samples were collected and analyzed for copper, zinc, and molybdenum. These data established local variance and necessary statistical controls. Following this, a total of 151 geochemical samples were used to survey the 3000 square-mile area. Computer contouring of results directed attention to specific target areas for detailed geologic analysis, property acquisition and drilling. A total of 22 copper-zinc and molybdenum anomalies were identified. Four of these were recommended for further exploration. To date, two have been acquired and drilled and preliminary ore reserve and financial analysis have been made on one. The estimated cost and time for the regional exploration phases leading to these targets were thirty man-weeks and $16,000.

Jan 1, 1973

By Edgar W. Sawyer

Attapulgite and sepiolite are the clay minerals used to thicken ionically contaminated watzrs in the preparation of drilling fluids. They are nonsweliing clays that can be dispersed and reflocculated by mechanical means to increase the viscosity of fresh water and salt and gypsum contaminated waters. Those gelled in fresh water do not become excessively thick when contaminated with high salt concentrations or polyvalent cations encountered during drilling. Gels formed exhibit thixotropy and yield pseudoplastic rheological behavior due to the particle interactions and mechanical interferences of the flocculated gel structure.

Jan 1, 1983

By Angelus S. C. Owili-Eger

The investigation into the hydrologic and hydrogeochemical influence of longwall coal mining in the Appalachian coal basin was under- taken in response to the need to technically address problems of damaged or impaired well yields, and quality deterioration. Prior to this study, issues regarding reduced aquifer yields and degraded water quality had to be handled in a very qualitative manner. Such an approach would, in the long run, claim a heavy toll on the mining industry. The primary objective of this undertaking, therefore, was to provide sufficient and reliable information base for the determination of the local and possibly the regional effects of longwall mining on well yields, and the hydraulic and hydrogeochemical parameters of the immediate surface and subsurface water systems. Specifically, the program was designed to supply definitive data to answer the following series of questions: 1. Does longwall mining affect the quantity and quality of water in local wells above and adjacent to longwall panels and barrier pillars? 2. If the water quality is affected as soon as mining takes place, does it heal? or if it is not affected immediately, does it change over a longer period of time? 3. How do the aquifer water transmitting characteristics respond to induced physical ad hydrologic variations? 4. What is the extent of the various changes in quantity and quality of the water resources? 5. Should and can standard hydrologic evaluation techniques be used to determine the hydraulic properties of highly fractured zones located within a larger and less permeable aquifer?

Jan 1, 1983

By Ralph W. Crosser

The emergence of residuals management as a planning and management tool in the mineral industry has been recently accelerated by the proliferation of environmental regulation and its associated costs. Residuals management practices allow for the early determination and integration of both production and environmental goals in the development of management strategies to arrive at the most cost effective, environ- mentally sound solution. The term residuals management was in actuality derived from the substitution of the word residual for the term ?pollutant? or ?waste?. A residual can be defined as a non-product output having no value in existing markets or a value less than the cost of marketing it. The values of the residual can be determined by time, technology, government policy, market conditions, etc. Residuals basically fit into two classes -- materials which are composed of liquid, gaseous or solids; and, energy, which mainly consists of heat and noise. These residuals are interrelated and can be modified by adding materials and/ or energy, which also may become a residual; thus, lending themselves to alternate disposal schemes to control the adverse effects.

Jan 1, 1979

By M. C. Radomsky

Approximately sixty, small, surface coal mines in Pennsylvania participated in a program designed to improve safety performance in the workplace. The method involved the use of safety sampling and observation to assess the safe standards of worker behavior and work conditions. Data were collected through the use of operation-specific, on-site safety records covering seven major occupational units. Workplace events observed (acts and conditions) were assigned a hazard classification; feedback, both immediate and delayed was initiated to improve safety performance. The experiences drawn from this pilot project have proven the need to continue to pursue this behavioral approach; however, a stricter methodology needs to be adopted in the collection and analysis of data.

Jan 1, 1987

By R. A. Hill

A brief explanation of the theoretical functioning of a regenerative system followed by its application to firstly, shuttlecars and then continuous miners and its effect on performance thereof with regard to handling, production and safety.

Jan 1, 1986

By J. W. T. Ropkins, D. Allenby

The paper describes a technique by which large concrete boxes are unobtrusively inserted beneath existing highway and railway infrastructure to form new subways, culverts and under-bridges, thus avoiding the inconvenience and costs of disruption to traffic associated with traditional cut and cover techniques. A series of project examples, undertaken in the United Kingdom and United States, are used to illustrate the design and construction of the box structures, together with the technology required to control ground disturbance in the tunnel face and around the box, and the jacking systems necessary for box installation.

Jan 1, 2003

By S. Tyson

The American Coal Ash Association, Inc. (ACAA) is an organization of producers and marketers of coal combustion byproducts. Since 1968, the goal of ACAA has been to gain recognition and acceptance of ccbs as an engineering material on par with competing virgin, processed and manufactured materials by advancing ccb uses that are technically sound, commercially competitive and environmentally safe. The use of ccbs is affected by local and regional factors including production rates, processing and handling costs, transportation costs, availability of competing materials, seasonal adjustments, and the experience of materials specifiers, design engineers, purchasing agents, contractors, legislators, regulators, and other professionals. An annual, survey of coal-burning electric utilities is conducted by ACAA to determine the quantities of ccbs produced and used in the USA. In 1993 approximately 88.5 million tons of ccbs were produced in the form of fly ash, bottom ash, boiler slag and byproduct from flue gas desulfurization (FGD). Approximately twenty-two percent of the combined production of these byproducts was used, while the remaining portion was deposited in disposal areas. The major markets for ccbs include cement and concrete products, structural fills, road-base layers, mineral filler in asphalt, grit for snow and ice control, blasting grit and roofing granules, grouting, coal mining applications, and waste solidification and stabilization.

Jan 1, 1995

By Dennis Arthur Fenton

The hydrodynamic bearing was first described by, Reynolds in 1886, and has since been widely applied in motors, engines, compressors, hydroelectric turbines, and other machinery. For various reasons, the hydrostatic bearing currently predominates in the large, horizontal rotating machinery field (e.g. grinding mills). However, the current industry trend towards increasing size and energy efficiency has resulted in renewed interest in the advantages of hydrodynamic bearings. These advantages include structural improvements, reduced bearing friction, improved bearing life, improved transient characteristics, and reduced lubricant pump size and power requirements. In particular, the higher energy efficiency results in substantial savings on large machines. This paper describes some aspects of the design of large hydrodynamic bearings based on thirty years, of experience in the design of such bearings on grinding mills ranging in journal size from 2.1 m to 6.4 m, see Table 1.

Jan 1, 1985

By A. I. Kogut

Impurity minerals in fluorspar ores and concentrates from a deposit in Southern Africa have been studied by reflected light, transmitted light, and cathodoluminescence microscopy. The principal impurities are quartz, calcite, aegirine, apatite, ankerite, magnetite, goethite, and synchysite [Ca(La,Ce,Nd)(CO3)2F]. Cathodoluminescence microscopy was found to be very useful in studying the character of the fluorite and especially for recognizing the presence of apatite and calcite impurities. Fluorite exhibits blue, calcite shows yellow, and apatite has white, light purple, and pink cathodoluminescence. The cathodoluminescent character of apatite varies with its geological environment and position in the orebody. The results of this microscopic study show that phosphorus present in fluorite concentrates occurs principally in binary locked apatite-fluorite particles. Successive fluorite cleaner concentrates contain progressively smaller amounts of locked apatite-fluorite particles. Free apatite has been effectively partitioned to the final tailings.

Jan 1, 1995

By Robert A. Bauer

Two basic types of subsidence occur in Illinois: pit and sag / trough. Pits develop over mines less than 165 feet deep and where relatively incompetent strata are found over the mines. Sag subsidence is found over mines as shallow as 75 feet and more generally over mines of greater depths. The percentage of subsidence and angles of draw associated with sag subsidence appear to be controlled by the rock properties at each specific site. The percentage of subsidence and angles of draw are smaller where the sites are not affected by geologic structures. An investigation to determine if a time factor based on the time interval from the date of mining to the subsidence events has shown that simple correlations with time, percent extraction, average pillar stresses, and pillar dimensions is not evident in Illinois.

Jan 1, 1982

By A. W. Mitchell

Mining of a bedded barite deposit exposed highly pyritic siliceous sediments which have weathered and degraded subsurface and surface waters. The ph, sulfate, and total dissolved solids are the most seriously affected parameters. Several solutions were tried and eventually horizontal holes were drilled into the mine wall to draw down the water table and decrease the movement of groundwater through oxidizing zones opened up by the mining operation. Areas of surface disturbance were capped with layers of soil, bentonite, and gravel to decrease the infiltration of water into the disturbed areas. These actions have begun to decrease sulfate and total dissolved solids concentrations and increase ph values.

Jan 1, 1987