Search Documents

By A. C. Noble, D. E. Ranta

Orebodies with intricate three-dimensional shapes (such as porphyry molybdenum deposits) are difficult to model using geostatistics or other computer-assisted methods. The strong trends in their spatial grade distributions occur as mathematically complex shapes and prevent the customary assumption of local stationarity that is required for accurate ore reserve estimation. "Zoned Kriging", a new method developed by AMAX, solves this problem directly by using the geologist's interpretation of the ore zones as a parameter in the kriging equations. The geological basis and methods used in the Climax ore zoning technique are reviewed and discussed relative to their application in zoned geostatistical modeling. The Zoned Kriging technique is described and demonstrated using data typical of mineral deposits.

Jan 1, 1992

By L. Sletmoen, P. Rocque, E. DeSouza

Plans for achieving planned production rates at the Red Lake Mine High Grade Ore Zone required that the mine ventilation system be upgraded. Time constraints required that only a site assessment of the mine ventilation system be performed followed by recommendations for providing adequate ventilation conditions at the production zone. This paper describes the engineering assessment, design and commissioning of the ventilation system upgrade for achieving increased flows at the high grade ore zone. The work was successfully achieved with minimal capital expenditures and disruption to the mining cycle.

Jan 1, 2003

By Z. Kowalski

In the non-operational ?Górka? quarry, there are situated both a waste disposal site of an area of 6.7 ha, containing approximately 1 million ton wastes from high aluminium content materials (incl. about 400000 t of wastes from aluminum hydroxide production), and a pond of an area of roughly 3 ha, up to 15 m deep, with about 400000 m3 of polluted water and infiltrates from the disposal site mentioned. The basic problem related to the effluents in the Górka pond is both their high alkalinity (pH 12-13.4) and a variable analysis of pollutants whose level increases appreciably with the pond?s depth. The solution offered provides, first of all, remedial pumping and a treatment of effluents retained in the Górka reservoir. Effluents would be treated in a reverse osmosis plant according to a process verified so far on a quarter-commercial scale. The treatment process by-product, a brine solution (containing about 25% NaCl) whose amount may reach up to 100000 m3 might be supplied to the Debiensko Mine, which produces technological salt from salt-bearing mine waters. In parallel, an intake of underflows of infiltrates would be provided (previous geochemical identification) in order to take them away from the high aluminum site (by means of deep wells, and possibly girdling ditches). Such effluents would be subject to treatment. The successive stage is the utilization of approx. 50000 m3 of bottom slurry, left in the emptied reservoir, in the production of self-solidifying mixtures, which would be then used for sealing the bottom and the banks of the Górka reservoir. The empty and sealed reservoir would be filled up with a volume of approx. 600000 t of ashes, coming from coal burning in the thermal-electric power station. For the last stage, instead, is scheduled the rehabilitation of the entire waste disposal site in the Górka quarry. The site will be drained, covered with a leveling, sealing and rehabilitating layer, which will allow to introduce plants on the rehabilitated waste site. Later on, the area could be turned into a town park

Jan 1, 2006

By M. Shen, T. D. Wheelock

The important characteristics of a gas-promoted oil agglomeration process for cleaning coal particles in an aqueous suspension were determined. Numerous agglomeration tests with scale-model mixing systems of different sizes with controlled amounts of air were conducted. The tests were conducted on high- and mediumvolatile bituminous coals using either i-octane or hexadecane as an oily agglomerant. The performance of the system was characterized by employing the minimum time required to produce spherical agglomerates (tE), the mean agglomerate diameter (dp), coal recovery and product ash content. Among these parameters, tE was found the most useful. It is a key parameter in the scale-up of an agglomeration mixing system. This parameter was found to depend on a number of system and operating variables. By controlling these variables and conducting further agglomeration tests with mixing systems that varied in size, an appropriate size scale-up rule was established.

Jan 1, 2002

By S. H. Advani, J. K. Lee, K. S. Chan, J. M. Avasthi

A summary of field equations governing the hygro-thermo-mechanical (coupled temperature, moisture, and stress) response of geological media is presented. The applicability of these equations, with appropriate boundary conditions, to the study of basic mechanisms associated with underground coal gasification (UCG) process is discussed. In particular, the phenomenon of stress-induced spalling resulting from intense drying near the gasified cavity and in situ effects is investigated by means of the finite element method. Some typical results from sample finite element model representations are presented for the evaluation of field experiments.

Jan 1, 1986

By C. Anderson, K. Nikkhah

This paper outlines the role of simulation software in design and operation of a typical metallurgical plant with mineral processing and hydrometallurgical units, to produce concentrate and pure metal. It addresses the role of simulation and mass balance software in the conceptual, feasibility and detailed design stages. It discusses the use of JKSimMet for sizing of mineral processing units, and METSIM and IDEAS for development of energy and mass balances. In detailed design of a plant, the complex interaction and variation in performance of various units makes it difficult to predict overall system performance and availability. Simulation is used to: assess operating strategies that affect surge capacities at various stages compare different ore types and mining strategies that affect concentrate product quality. optimize transportation logistics for raw materials, concentrate and metal products

Jan 1, 2001

By J. E. Spencer

Mesozoic and Tertiary mineral deposits in west-central Arizona are commonly associated with Mesozoic thrust faults and Tertiary detachment faults, respectively. Quartz-kyanite rocks and pyritic quartz-sericite schists with local anomalous gold are the product of probable Jurassic argillic alteration of Jurassic volcanic, sedimentary, and plutonic rocks followed by Cretaceous thrust burial and associated metamorphism. Slivers and sheets of Paleozoic carbonates along Mesozoic thrust faults were locally sites of syn-and post-thrust mineralization. Widespread brecciation along Tertiary detachment faults resulted in increased permeability along fault zones. Elevated thermal gradients also resulted from detachment faulting and apparently caused convective aqueous-fluid circulation along detachment faults and associated Fe+Cu±Au mineralization.

Jan 1, 1988

By Stephen Navin, Pablo Ferradas, Carlos Silvestri, Alexander Markov, Jon Kaneshiro

In the high Andes of Peru, two tunnels are being constructed totaling nine kilometers in length at an elevation of over 4,500 meters. The tunnels convey freezing and crystal-clear waters from rainfalls, streams, and lakes for the consumption of Lima. The drill and blast 3-meter wide by 4-meter high tunnels are being driven from both ends through folded and sheared volcanic tuff, andesite, agglomerate,and limestone, where groundwater inflow is high. This paper describes the design geological and groundwater inflow investigations and construction.

Jan 1, 1999

By G. P. Dvoichenkova, E. A. Trofimova, M. V. Zaskevich, V. A. Chanturiya

The paper presents theoretical and practical aspects of directed adjustment of physicochemical properties (pH,Eh) and ion composition of recycle and mine water by electrochemical treatment. Treatment is run in the conditioners of diaphragm-type with production of alkaline catholyte of pH value up to 12 and acidic anolyte of pH up to 2. In process of water electrolysis the directed motion of Mg2+ and Ca2+ ions is observed from anode volume to cathode one, were they precipitate as hydroxides and carbonates; it leads to decrease of salt content in anolyte and catholyte. The anolyte has been concentrating anions, it is being saturated with oxygen, which reaches 20-35 mg/L. The results of experimental and industrial testing of electrochemical technique for mine and recycle water in flotation of diamond-containing and sulphide-scheelite, hematite, phosporite, apatite-nephelite, bauxite ores indicated the increase of recovery up to 2-1 5% and grade up to 0,5-2%, concurrent with decrease of reagent consumption from 15 to 50 %. Modules of industrial conditioners of different type capacity have been developed.

Jan 1, 1995

By T. C. Page, P. C. Gibson, M. A. Miller, J. D. Sell

[The Yarnell gold deposit in the Weaver mining district, Yavapai County, Arizona, occurs in a structurally controlled, hydrothermally altered zone in a 1700 Ma granodioritic intrusive. Both potassic and sericitically altered rocks around and above the low-angle, northeast striking Yarnell fault are known to host economic gold mineralization. A wider envelope of weakly-propylitic altered rock also occurs in this area. During mineralization, strong sericitization accompanied several stages of quartz (±adularia) veining, stockwork formation, localized silicification and potassic replacement, in association with deposition of specularite, pyrite (now oxidized) and gold. The footwall of the fault is also sericitically altered but poorly mineralized. Mineralization along the Yarnell fault continues both northeast and southwest from the main deposit, although the thickness of the zone and associated alter avian envelope diminish away from the orebody A sample of undo formed illite taken from the Yarnell fault zone was K/Ar dated at 69 + 1.6 Ma. This date reflects a minimum age for both mineralization and latest movement on the fault. Gold mineralization is accompanied by modest increases in Ag, As. Cu and Mo content. Both CO2- and H2O- rich fluid inclusions were studied and suggest mesothermal pressures and temperatures of formation for the deposit. Ninety-six reverse circulation holes and four diamond drill holes outline a bulk-minable mineral reserve of'4.1 million tons at 0.051 oz of Au per ton. An additional 2.7 million tons at 0.017 oz of Au per ton occurs in a low-grade zone above and subparallel to the main mineralized zone. Total calculated mineral inventory stands at 6.8 million tons at a grade of 0.038 oz of Au per ton, with a waste-to-ore ratio of 1.45:1. Column leach tests indicate that cyanide heap leach gold recoveries should exceed 70%.]

Jan 1, 1994

By J. F. T. Agapito, C. E. Brechtel, M. E. Adam

Full-scale stopping and simulated over- cast structures were constructed in large opening (30 ft high by 55 ft wide) room and pillar excavations in an oil shale mine. The program was undertaken to develop construction techniques and to generate data on structure costs and leakage rates. Leakage rates were measured using both sulfur hexafluoride tracer gas and "brattice window" methods at varying differential pressures. The measurements were conducted before and after a full-scale face blast to characterize the effects of blasting on leakage, and blast air pressures were measured across the stoppings. The operating performance of different combinations of permanent and temporary stoppings was evaluated by developing an operating model for a two-panel oil shale mine. The operating performance for the different stopping combinations was then compared to the system cost to evaluate the overall performance.

Jan 1, 1987

By R. H. Clarke

"INTRODUCTION Characterization of waste rock is frequently an oversight in mine planning which can contribute to significant delay in permitting and ultimately development. Thorough waste rock characterization is now a prerequisite to developing operating and closure plans acceptable to regulators and the public. BACKGROUND A long history of mine development has placed virtually all focus on the economic extraction and beneficiation of ore materials, while waste rock characterization and management received substantially less attention and consideration. Inadequate waste rock characterization has contributed to planning and management practices that are having unintended and unforeseen impacts to surface and groundwater, and in some cases lead to significant long term closure liability. In response, the regulatory community has developed guidelines for performing waste rock characterization during the pre- mine permitting process that in some cases seem onerous (BLM, 2013). Additionally, where a project proponent has not met these guidelines or results have been deemed “inadequate”, the Nevada Division of Environmental Protection and Bureau of Land Management (regulatory agencies) will only issue operating permits with rigid management practices to address the uncertainty, including requirements for lining waste rock facilities. WASTE ROCK CHARACTERIZATION FOR NEVADA PROJECTS Newmont Mining Corporation (Newmont) operations in Nevada approaches waste rock characterization like ore characterization, as it requires a similar investment of time, funding and attention to detail in order to pass public and regulatory scrutiny. Newmont follows a tiered approach to characterization that creates three over-lapping data sets representing an “escalation” in analysis at each tier, an approach that has thus far gained regulatory approval. “Tier 1” waste rock characterization for most Newmont projects begins with exploration drilling which follows internal standards and procedures. 20-foot composite samples are prepared from all drilling and analyzed for multiple trace elements using inductively coupled plasma mass spectrometry (ICP-MS) methods and for acid-base characterization using method ASTM-E1915. If the exploration program is successful and further resource or reserve development is recommended, the Tier 1 data are used to prepare a Waste Rock Characterization Plan (Plan) that will be presented to regulatory agencies as a part of baseline project characterization."

Jan 1, 2015

By Z. T. Bieniawski

In the past 15 years, rock mass classifications have experienced unprecedented development and have emerged as powerful practical methods for assessing ground conditions and tunnel support. Such methods as the RMR System (Geomechanics Classification) and the Q-System have provided many advantages over the classical Terzaghi rock-load method introduced in 1946. These new classifications have found wide applications all over the world but some doubts have been expressed and shortcomings pointed out. The author, who developed the RMR System, takes a penetrating look into the promises and the pitfalls of modern rock mass classifications. He dispels some misconceptions and shows how rock mass classifications can serve as effective and dependable design aids in tunneling.

Jan 1, 1987

By Bekta? Uz

In this research, geological characteristics of sand quarries around the village, Kemerburgaz Akpinar, are studied and the mineralogical, petrographical, chemical and technological characteristics (such as sieve analysis, relative density, water absorbtion etc.) of the sand samples, obtained from the area are explained. In the general area sand' quarries, being in lacustrine formations belonging to Neogen, the stratigraphic location of the sand occurences take place at high levels of these formations, geologically. All of this pattern, being under 1 mm with a ,particle dimension, it ranges from 0,5 mm in the quantity of 99 % to 0,25 mm in the quantity of 15 relative density is 2,65 g/cm3 ; water absorbtion is 0,9%. Mineralogically, the sand samples contain Quartz (84%), Feldspar (3%), Calcite + Aragonite (10%), Pyroxen+Amphibole (1-2%), Garnet+Tourmaline (0.5%), Olivine (0.1-0.5%). Besides, sand samples contain SiO2 with the quantity of above 90%. Containing Quartz at high levels for mineralogical, petrographical and chemical characteristics, Akpinar sand will be evaluated as silica sand when the carbonate mineral is removed with the method of ore preparation such as leaching.

Jan 1, 2005

By J. A. Brierley, S. R. Hutchins, C. L. Brierley

Introduction Many gold and silver ores are refractory to conventional processing technologies. Thus, precious metals recovery is uneconomic. These resources can consist of ores, flotation concentrates, mill tailings, and other reserves. The refractory nature of these materials can be ascribed to such components as iron sulfide minerals, silica minerals, tellurides, organic compounds, and sulfosalts. Precious metals locked within iron sulfide minerals account for a large number of refractory gold ores. These minerals consist principally of pyrite or arsenopyrite. They must be oxidized to liberate the encapsulated precious metal and allow its contact with the leaching agent. Carbonaceous gold ores represent a unique class of refractory precious metal ores in general. Not only does gold encapsulation by iron sulfide minerals occur (Hausen, 1985), but these ores also contain organic matter that interferes with gold recovery by cyanidation. Direct interference can be attributed to either occlusion of gold within organic matter or formation of a stable gold-carbon complex. The magnitude of this problem is debatable. Wells and Mullens (1973) examined two carbonaceous gold ores and found no association between the gold and carbonaceous material. A more common problem is indirect interference, whereby the aurocyanide complex formed during cyanidation is sorbed by the native organic matter and is not available for recovery. This phenomenon is referred to as "preg robbing" (Osseo-Asare et al., 1984; Hausen and Bucknam, 1984). Guay (1981) summarized various methods that can reduce preg robbing during processing of carbonaceous gold ores. However, some are not applicable to carbonaceous ores that have significant amounts of gold locked in iron sulfide minerals. Several methods exist for oxidizing iron sulfide minerals and rendering refractory precious metal ore amenable to conventional recovery processes. These include various embodiments of roasting (Jha and Kramer, 1984; Brown, 1984; Arriagada and Os-seo-Asare, 1984; Smith, 1986), pressure oxidation (Muir et al., 1984; Beattie et al., 1985; Thompson, 1986; Weir et al., 1986; Argall, 1986), and chemical oxidation (Scheiner, 1971; Jackson, 1983; Van Weert et al., 1986). Each process has been successfully used for refractory precious metal ores. In many instances, however, their use is precluded by capital and operating costs relative to the value of the ore. An alternative to these methods is microbial pretreatment - a biological process whereby iron sulfide minerals are degraded and the liberated precious metal values can be recovered by conventional technologies. Bioleaching refractory precious metal ores is a relatively new concept compared to roasting and chemical oxidation. It is rapidly becoming established as a viable pretreatment alternative. Numerous studies have been conducted in the laboratory and on a pilot scale (Yudina et al., 1979; Lawrence and Bruynesteyn, 1983; Pol 'kin et al., 1985; Marchant, 1985; Livesey-Goldblatt, 1985; Gibbs et al., 1986). Comparative tests have demonstrated that bioleaching can be equal to or better than roasting or pressure oxidation in terms of product recovery and process economics (Fridman and Savari, 1983; Livesy-Goldblatt et al., 1983; Karavaiko et al., 1985; Gilbert et al., 1986; Hackl et al., 1986). Bioleaching's main drawback is that pretreatment requires days rather than hours. This can lead to excessive operating costs for difficult-to-treat ores. In all of the tests reported thus far, the leaching microorganism used has been thiobacillus ferro-

Jan 4, 1988

By G. S. Grainger, R. A. Cummings, F. S. Kendorski, R. L. Butts

Georgia Power Company's Rocky Mountain Project, located approximately ten miles northwest of Rome, Georgia, in the Valley and Ridge Physiographic Province, is a pumped-storage facility rated at approximately 800 megawatts of peaking energy. Geological field explorations and borings enabled the division of the rocks along the tunnel and shaft alignment into distinct lithologic units and defined the ground--water regime. Field explorations included a detailed analysis of the rock mass discontinuities at available rock unit exposures. Testing of rock strengths was performed in several phases in both the field and the laboratory. The field testing consisted of point-load testing, geophysical testing, in situ load testing, and hydro-fracture testing. Laboratory testing determined the Brazilian split-tensile strength, the unconfined compressive strength, the triaxial compressive strength, the joint-direct shear strength, and the pulse velocity. The rock mass along the tunnel and shaft was also characterized by empirical classification systems. The classification systems included the Rock Mass Rating (B1IR) and the Rock Mass Strength Determination (RHSD). The results of the field explorations, field testing, laboratory testing, and rock classifications were used to divide the rocks into two structural groups. These rock groups were defined as volumes of rock wherein the rock mass behaves similarly in response to the excavation. Each group, therefore, required separate rock engineering consideration.

Jan 1, 1986

The declining grades of surface deposits have re-confirmed the need for greater production rates. Large scale production requires increased investments in expensive and sophisticated equipment. The key to successful operations can depend entirely on proper equipment utilisation and in this program of research at the Department of Mining and Metallurgical Engineering, University of Queensland, much emphasis has been placed on the analysis and improvement of this aspect of a load-haul-dump operation. For a model to be successfully integrated into a mine engineering function and readily accepted by mine operating personnel, it has to offer more than just results. The concepts used in its design and construction must include sufficient detail to enable engineers to apply it usefully and with confidence.

Jan 1, 1979

By S. R. Rao, J. A. Finch, E. El-Ammouri, K. Ngoviky, P. A. Disten

Sludges produced by lime treatment of acid mine drainage (AMD) can contain significant quantities of base metals which represent both a potential hazard and a loss of values. A new technique for metal recovery from sludge is proposed by combining selective acid leaching and adsorption of metal ions by activated silica sol. The process is demonstrated on two AMD sludges, one containing primarily nickel and the second zinc. They were first treated with sulphuric acid (pH 3.5) to selectively leach the target metals and then activated silica sol was added to the leach solution to adsorb the nickel and zinc. Thickening and centrifuging gave about 90 percent rejection of the input volume to effluent. The adsorbed metals were redissolved by strong acid into a concentrated solution relative to the feed and the silica sol was recycled.

Jan 1, 2000

By L. J. Prosser, A. T. Iannacchione

From 1991 through 1995, 44 miners out of a total workforce of less than 2,000 were fatally injured in the stone industry. Of these, 12 occurred at underground mining operations with nine deaths resulting from roof or rib falls. A safer environment can be achieved by evaluating the nature of the hazardous ground and by developing more efficient and effective ground-control strategies. Roof and rib conditions were observed and assessed in 33 underground stone mines in Illinois, Indiana, Kentucky, Maryland, Missouri, Pennsylvania and West Virginia (Fig. 1). Hazard assessment indicated that the ground failures that occurred under moderate to substantial overburden, i.e., >30 m (100 ft), were caused by stress concentrations and geologic structures. Ground failures near the surface are caused by solution (water) processes. Selection of the mining horizon and mine-layout decisions

Jan 1, 1999

By J. M. Mutmansky, Aiping Wang

This paper outlines the patterns of methane emission in both longwall and room-and-pillar operations and discusses the effects that these patterns have on the decision as to whether the methane is most economically handled by ventilation alone or by means of a methane-drainage system in addition to ventilation. The costs of handling the methane in the ventilation system and the costs of implementing the methane-drainage system are discussed, as well as the costs related to the production of coal. The important issues of production slowdowns and gasouts are also discussed, as well as the proper response of mine management to such a situation. Suggestions concerning the keeping of production records related to methane problems are made, and the justification for more intensive economic analysis of coalbed methane extraction and utilization is discussed

Jan 1, 2000