Search Documents

By C. J. Veal, C. I. House, S. R. Bellamy

INTRODUCTION Coal gold agglomeration (CGA) is a new concept in gold processing. It involves the recovery of oleophilic (oil-loving) gold grains by causing them to adhere selectively to the surfaces of coal oil agglomerates. Under optimum conditions very high recoveries of gold. can be achieved. The agglomerates are recycled to build up gold loading to typically 1000 - 5000 g/tonne. Bullion can be produced by burning the loaded agglomerates with subsequent recovery of gold from the highly loaded ash either by dissolution/electrowinning or smelting. A wide-ranging programme of laboratory testwork has been performed to investigate the response of different ore types to the process. This has shown CGA to be most applicable to ores in which the gold is liberated or easily liberatable, relatively coarse (ca 500 µm) and fine (<5 µm) gold grains being recoverable with equal ease. The best opportunities for CGA seem to be: • placers containing fine gold not recoverable by gravity concentration • low grade gravity concentrates to avoid multiple magnetic/gravity separation stages and amalgamation • free milling ores where the gold can be liberated at a reasonable ore particle size eg >d80 50 µm • tailings past or present from gravity concentration plants. CGA testwork ranging in scale from laboratory to pilot plant on tailings produced by gravity concentration in the 19th century Australian gold rush has already been reported (Bonney, C F, 1988; House, C I, Townsend, I C and Veal, C J, 1988). An economic appraisal for a Canadian free milling gold ore has also been published (Buckley, S A, House, C I and Townsend, I G, 1989). This paper describes results of a detailed laboratory programme to assess CGA as a means of recovering gold from a beach sand deposit in New Zealand. The area from which the samples were taken consists of quarternary interglacial marine, lagoonal, fluvial and eolian deposits. The heavy minerals present are predominantly ilmenite and garnet and small concentrations of gold. In certain locations the sands and gravels are consolidated by a limonitic cement. In the 19th Century some parts of the deposit were mined and the ore processed using stamp milling and gravity concentration. Gold recoveries were low, probably below 50%, due primarily to the fine size of the gold grains, the flaky nature of the gold and also imperfect liberation by the stamp mills. Our laboratory testwork was divided into three parts: i) Preliminary studies on an initial sample to assess the feasibility of treating the ore by CGA ii) Extended studies on further samples from various locations in the deposit to confirm predictions from (i) iii) Conventional gold recovery techniques. EXPERIMENTAL PROCEDURES All CGA tests were performed by agitating a slurry of ore in water in a 0.6 dm3 pyrex beaker fitted with four vertical baffles. When required, potassium amyl xanthate collector was added and the slurry conditioned for 5 min. Coal (ex BP Coal Australia&apos;s Tahmoor Colliery) previously ground to a d80 50 µm was added followed by a commercial grade of gas oil (density 840 kg/m3). The agglomeration time was 30 min. The agglomerates were separated from the tailings by screening, both were then dried and analysed for gold by fire assay. This test procedure provides a reasonably accurate estimate of gold recoveries that might be expected from our 1 tph pilot plant. Ore samples were ground either dry in an agate ring disc mill or wet in a steel batch tumbling

Jan 1, 1989

By Shan Mafi

he Broken Aro coal mine is located at the Woodbury Wildlife Preserve 11 km (7 miles) west of Coshocton, OH on State Route 541. Underground min¬ing at the 16-hm2 (40-acre) site took place during the 1910s. During the past five years, surface mining has occurred along the western and northern perimeters of the underground region. The Ohio Department of Natural Resources (ODNR), R&F Coal and American Electric Power (AEP) are involved in a project to remine the abandoned underground complex. The program also includes installing a mine seal made of fixated flue gas desulfurization (FGD) material. Previous mining activity in this area has resulted in an acid mine drainage (AMD) problem on portions of the reserve. In particular, a prominent AMD source is present in the Simmons Run drainage. The project goal is to eliminate or reduce the AMD that is discharging into the watershed. It was initially hoped that the Simmons Run drainage area could be economically mined. Accordingly, this area was included in the mine permit. However, experience with other previously mined areas on this reserve showed that the old mine workings were more extensive than originally thought. Old mine workings present several problems. The most significant are reduced coal recovery, poor coal quality and AMD liability. All of these problems increase mining costs. And the more extensive the old workings, the more significant the increase in cost. Based on R&F&apos;s experience with old mine workings in this area, it was decided that economic recovery of the Simmons Run drainage reserve was not possible. As a result, R&F excluded the Simmons Run drainage area from its early mine plans. Some time after it was decided not to affect the Simmons Run drainage area, R&F and ODNR&apos;s Division of Mining and Reclamation discussed the possibility of removing this area from the permit and attempting to correct the AMD problem as an Abandoned Mine Lands (AML) project. Specifically, the discussion centered around mining through a portion of the old mine workings to expose the mine openings in the highwall. Once exposed, the mine openings would be sealed using FGD material from the nearby Conesville power plant operated by AEP. In addition, there was interest in reclaiming the old tipple and associated gob pile located adjacent to Coshocton County Road 17 on the opposite side of Simmons Run. R&F attempted to eliminate the AMD problem by sealing the mine openings with FGD material. Once the seals were installed, they were covered with overburden. Monitoring wells were installed to determine the effectiveness of the seal and the inundation progress in the old mine workings as well as monitoring the quality of ground water. The project was jointly funded by revenue from the sale of the coal recovered during the project and AML funds. The FGD seal is expected to cause well water levels to increase above preseal elevations. However, the additional head pressure due to increased water depths in the underground mine may cause seepage through the bottom of the mine or out through the perimeter. The in¬creased water depth in the underground mine is expected to cause lower oxygen concentrations in the underground mine water. Since acidity is produced by oxidation of iron pyrites, less oxygen should result in better quality water. Monitoring wells will be installed before seal installation so that pre- and postseal water levels and well water quality can be determined. Surface sampling locations will be identified. These will be monitored before and after seal placement.

Jan 1, 1998

By J. W. Leonard

Introduction Gravity-based coal/mineral preparation plants must be operated to yield products of a quality satisfactory to existing markets. However, because of historic control problems, recovery is frequently sacrificed to achieve quality, resulting in losses of valuable product. Plant control has ranged from intuitive in-plant spot quality judgments made by various operators to gross methods involving such devices as density gauges, floats, grabsample on-the-spot sink/float tests, etc. Millions of tons of quality coal/minerals are lost to refuse each year, because of the historic lack of a continuous and dependable control system. The result is serious economic, as well as environmental, losses. While the economic losses are obvious, the less obvious environmental ones, in the case of coal, result from the misplacement of more ignitable quality fuel to refuse banks. Until recently, a control system capable of supplying a market-grade coal/mineral product, while continuously minimizing product losses to refuse, has been technologically unavailable. Coal/Mineral Washing Tracer System Performance Monitor (CMWTSPM) The first Coal/Mineral Washing Tracer System Performance Monitor (CMWTSPM) originated in the late 1970s as an innovative idea and ultimately resulted in Leonard Patent No. 4,345,994 issued on August 24, 1982. In a classic example of successful university basic research, the patent was followed by two US Department of Energy (DOE) merit awards for fundamental optimization research at the University of Kentucky, a number of publications, a successful applied research program (underwritten by SENTREX at Irvine, CA) and field tests at the Rochester and Pittsburgh Coal Company Keystone Mine near Indiana, PA. The system is now operational and is marketed by SENTREX as the SENTREX Performance Monitor. A diagram of the system is shown in Fig. 1. This system relies on metal detection as the basic tracing medium. Since it is capable of tracing particles as fine as 0.19-in., the system is ideal for coarse coal/ mineral cleaning processes. Basically, the CMWTSPM records the distribution of synthetic coal/mineral particles, of known size and specific gravity, between product and refuse output streams of coal/mineral washing, gravity-concentrating processes. For any given particle size, surface area and shape are constant. The particles are [ ] designed to find their way into the center of their respective inprocess specific gravity/size streamlines. The system will yield a complete partition curve to show the percentage of misplacement for any selected size/specific-gravity particle fraction, thereby providing a point-to-point insight into process failure. When used to evaluate operational processes, this full partition curve is far more diagnostic than the simplifying, derivative, single index number known as the Ep value. The Ep value is commonly used for convenience to represent symmetrical partition curves, but, if the actual partition curve is non-symmetrical, use of the Ep value can result in serious diagnostic error. While the Ep is useful in design and for rapid performance evaluation and process adjustment, the full partition curve is by far the more diagnostic. It will provide insight into the behavior of particulate flow, through non-symmetry, as a means to highlight potential systemic failures. Performance of the process is measured and improved by determining the extent of particle misplacement and by making timely adjustments to the unit to reduce the misplacement. Used in this manner, the CMWTSPM is not only a long needed processing control monitor, but it is also a very powerful diagnostic tool which, in the hands of skilled operators, has

Jan 1, 1993

By Lynton B. Manssen

Introduction Net Present Value (NPV) techniques are becoming widely used in industry as a standard analytical tool in making capital budgeting decisions. However, NPV techniques are often misused in "common practice." A comparison was made between the use of NPV techniques in common practice and an Adjusted Net Present Value (ANPV) approach to capital budgeting in the financial analysis of a mining project. The comparison was made by applying both methods to a hypothetical copper project. The intent of the analysis is to provide an example for practitioners to follow when financially analyzing mining (or other) projects. To maintain the thrust of the analysis, the project has been evaluated as a stand alone, total project. No consideration has been made of the division of cash flows accruing to various owners over the life of the project. This omission will not affect the comparative nature of the analysis. This discussion assumes that the reader is familiar with present value as a concept and as a tool in capital budgeting. Finance theory has embraced NPV analysis as the correct way to evaluate capital budgeting alternatives. Many articles have been written expounding the virtues of NPV over other capital budgeting methods, such as Internal Rate of Return (IRR), Payback, Accounting Rate of Return, and others. It is not the purpose of this article to review all of the literature in this area; suffice it to say that in academic circles NPV concepts are accepted as the norm. A survey by Schall, Sundem, and Geijsbeck (1978) indicates that major US companies are finally following in academia&apos;s footsteps. Fifty-six percent of the companies responding to the survey use NPV techniques in their capital budgeting process. Further, some 86% of the companies surveyed use discounted cash flow methods (NPV or IRR) for capital budgeting decisions. This compares with a survey by Klammer (1972) that showed 57% of companies using both techniques, a considerable increase in seven years. With the increasing use of NPV techniques in industry, there are certain uses in common practice that can give misleading results. Five common errors in NPV analysis of large projects are: • No distinction is made between real and nominal cashflows. • The discount rate(s) used in the NPV analysis is not formally adjusted for risk. • There is no distinction of possible differences in the riskiness of different project cash flows; i.e., revenue vs. depreciation. • There is no recognition of the cash benefits to the project from interest tax shields (interest payments on the project&apos;s debt that are tax deductible). • There is no clear recognition of subsidies to the project from concessionary debt financing. No Distinction Between Real and Nominal Cash Flows Often, expected cash flows for a project are stated as a mixture of real (in constant dollars) and nominal (in current dollars) cash flows. For example, expected revenue cash flows may be stated in real terms and depreciation may be stated in nominal terms. If cash flows are added together to give an after tax cash flow, and this single cash stream is discounted, care must be taken to ensure that cash flows are consistently stated. All cash flows should either be stated in nominal terms or in real terms. In addition, the discount rate used must be stated in the same terms as the cash flows being discounted. Real cash flows must be discounted using real discount rates and nominal cash flows using nominal discount rates. Discount Rate Not Adjusted Numerous methods for obtaining discount rates are used in common practice. Schall and others

Jan 6, 1983

By S. K. Kawatra, S. K. Valluri, S. J. Root

Common carbon dioxide capturing reagents, such as amines and sodium hydroxide, are expensive, toxic, and energy intensive to regenerate. We have added frothers to a sodium carbonate solution in order to increase the surface area available for CO2 transport within the packed bed of a counter current scrubbing column. Addition of frothers has improved the performance of sodium carbonate scrubbing solutions to be on par with sodium hydroxide scrubbing solutions. This novel enhancement of a relatively inexpensive CO2 capture-regeneration cycle shows potential to allow plants to turn a profit by sequestering a waste product. These results are discussed in detail in the following manuscript. INTRODUCTION The combustion of fossil fuels converts chemical energy to thermal energy. CO2 is produced as a byproduct of the reaction. 80% of the world’s electricity is produced by using this thermal energy to power a generator, accounting for 40% of global carbon dioxide emissions. In an effort to stabilize the rising atmospheric CO2 levels, researchers are investigating the application of carbon capture and storage (CCS) systems in power plants. [1] Efforts to capture CO2 at some power plants have been successful, but the cost of installing and operating the required equipment is high. As such, very few power plants have CCS systems. If CO2 can be captured and processed into a product that can be sold at a profit, installing CCS systems in power plants will be a very attractive business decision. In order for the sale of captured CO2 to become a profitable venture, the cost of capturing the CO2 from a flue gas must be reduced. BACKGROUND The most common method for separating CO2 from a flue gas is by passing it through a counter-current packed bed scrubbing column. The flue gas enters the bottom of a column while a solution of a chemical with properties advantageous to the absorption of CO2 is pumped to the top. The fluids interact in a packed bed, where the CO2 is transported from the gas to the liquid. CO2 is an acid gas, so it is common for the scrubbing solution to be alkaline in nature in order to neutralize the carbonic acid that is formed when it is dissolves into water. The exhaust exits the top of the column free of carbon dioxide, which exits the column in the scrubbing solution, reacting or complexing with the absorbent. Figure 1 is a schematic drawing of a CO2 scrubbing column. It shows the molar flowrates and compositions of the gas and liquid at the bottom [1], the top [2], and an arbitrary height in the column [Z]. [2,15] L is the molar flowrate of liquid at any point in in the column. G is the molar flowrate of gas at any point in the column. Since the CO2 is transported from the gas to the liquid, L and G are variable with respect to height. To simplify calculations, the CO2 free molar flowrates Ls and Gs are often used. X is the fraction moles of aqueous CO2 per mole of CO2 free liquid. Y is the fraction moles of gaseous CO2 per mole of CO2 free gas. Figure 2 is a composition diagram of the scrubbing column depicted in figure 1.

Jan 1, 2019

By Bruce D. McCellan

INTRODUCTION The gathering arm loader was patented by Joseph Joy in 1916. This unique machine motion became the standard of the industry and is used on underground loaders and continuous miners throughout the world. Figs. 1 and 2 show two types of gathering arm loaders. The gathering arm loader is a crawler-mounted ma¬chine primarily used for loading coal in a conventional mining system. Other uses also have been found for this machine in noncoal mines and other industries. MECHANICAL ASSEMBLIES The front or loading end of the machine, commonly called the head, consists of a tapered structural frame, hinged at the rear to the chassis and riding the ground at the front. Two bevel-gear cases are mounted in the head. They are connected by a timing shaft, which also acts as a conveyor drive shaft on most models. An eccentric disk attached to each gear case drives the gathering arms. The rear of the arms are attached to a swivel assembly. The motion derived from this arrange¬ment gathers loose material from the ground directly in front of the machine and loads it into the conveyor. Power for this drive is provided by two electric motors mounted under the gathering head. A speed reducer attached to each motor provides a gathering arm speed of approximately 5.2 rad/s (50 rpm). A torque limiting clutch is provided on each reducer to guard the system against sudden impact loading and continual overloading of the motors. The conveyor consists of an open box section through which a universal-type chain carries the ma¬terial to the rear of the machine, where it is discharged into the haulage vehicle. The chain is driven by a sprocket located on the timing shaft between the two gathering-head bevel-gear cases. On some large loader designs, primarily for noncoal applications, the chain is driven by a separate gear motor at the discharge end of the conveyor. However, the system driven by the timing shaft is used most widely. The conveyor frame is hinged just to the rear of the gathering head. It can be raised or lowered by hydraulic cylinders to the desired discharge height. The conveyor frame also is designed to pivot 0.79 rad (45°) either side of the center, just to the rear of the chassis. This feature increases the maneuverability of the ma¬chine and makes it possible to discharge material into the haulage system when in tight quarters such as when turning a crosscut. This function also is controlled by a hydraulic cylinder. The chassis of the loader consists of two crawler frames and cross members, holding the frames in position. The frames are either welded or cast as¬semblies. Replaceable wear runners are provided on the frames to take the wear generated by the crawler chain. An adjustable take-up idler keeps the crawler chain in proper adjustment for maximum life. The drive system for the crawler chains varies with the manufacturer, but it generally is one of two basic designs. One system provides a traction motor for each side of the machine, coupled to a speed reducer. A spur and bevel-gear train transfers power to the sprocket, which drives the crawler chain. Directional control is achieved by disk-type clutches. The other system also uses a motor for each crawler, coupled to a speed reducer. A roller chain drives the sprocket, which in

Jan 1, 1982

By J. K. Conibear

Since the 1948 introduction of hydraulic fill at the Sudbury Ontario Mines of the International Nickel Company of Canada, 32,000,000 tons of water-borne sandfill and 420,000 tons of portland cement addition have been placed in underground workings. Fill method mining, currently conducted at six of the ten operating mines, accounts for 28 percent of the total mines underground production. Both classified mill tailings and screened alluvial pit sand are used as fill for cut-and-fill primary mining, undercut-and-fill pillar recovery, and backfilling of blasthole and shrinkage stopes. Cemented fill, consisting of a lean mixture of portland cement, is used in areas where a stabilized fill is required to reduce dilution and aid in the recovery of adjacent pillar ore.

Jan 1, 1970

By Yongsik Jeong, Kwangmin Kim

Most tailings storage facility (TSF) failures occur in active, upstream-type TSFs, often due to extreme and unexpected weather conditions—specifically, heavy rainfall and strong winds. This case study of a TSF in southern Arizona examines the use of the optimum safe beach distance (Doptimal, the optimum distance between the crest and decant pond) as a tool for monitoring geotechnical stability and reducing catastrophic failures. A digital model of the TSF was used to determine the critical beach distance (Dcritical) under normal weather conditions, and Doptimal was then determined by adding incremental distances to account for the effects of heavy rainfall (Drainfall) and strong winds (Dwind). To overcome accessibility issues, a drone was used to map the TSF geometry and create a digital model. This model served as the basis for conducting a coupled stress-seepage, finite-element (FEM) analysis with a safety factor of 2.0 to assess geotechnical stability (Dcritical). The safe beach distance increments were determined using the PMP (probable maximum precipitation) and possible maximum wind speed. Based on this analysis, the optimal safe beach distance at the study site was identified as 202.2 m. Since the current beach distance (371 m) exceeds this value, the TSF was considered to be stable and satisfied the design safety factor of 2.0. However, this distance should be reassessed periodically to account for changes in the TSF geometry and other conditions. Furthermore, it applies only TSFs that are well-managed and feature a smooth, non-undulating beach surface with a consistent slope.

By Patrick McElhinney, Jacob Carr, Bruce Whisner, Cory DeGennaro, Jingcheng Li

Since 2016, electromagnetic interference (EMI) of personal dust monitors (PDMs) with magnetic proximity detection systems (PDSs) has been observed in underground coal mines. The EMI causes the magnetic field measurements of a PDS to change, which, in turn, alters the calculated location of the miner relative to the machine. Any altered location calculation can potentially cause the PDS to fail to warn a worker who is at an unsafe distance from the machine, arousing a serious concern on safety hazard caused by EMI in underground mines. The search for EMI mitigation strategies led to the development and use of large shielding pouches and boxes to hold the entire PDM to reduce its magnetic emission. Research on these pouches and boxes found that although they were able to reduce the emitted radiation from the PDM, they also disturbed the magnetic field of the PDS, affecting its performance. Researchers from the National Institute for Occupational Safety and Health (NIOSH) have focused on shielding internal PDM components rather than shielding the entire PDM. The PDM air pump motor is one of the PDM components that has been identified as a major source of electromagnetic radiation and has been selected for further study and tests. The measurements show that a small copper or aluminum foil enclosure can effectively reduce the magnetic emission of the motor by between 50 and 85% at 73 kHz. This study compares the test results of the air pump motor with various cost-effective shielding materials. The data provided in this paper can serve as a reference for shielding enclosure design of the PDM air pump motor to reduce its electromagnetic emission as one form of EMI mitigation strategy.

By Ross D. Lawrence

Suggestions have been made that the appraisal of mining assets using discounted cash flow techniques should be based solely on proven and probable reserves in reliance upon the widespread international recognition of uniform resource definitions. Following a review of generally accepted valuation principles, a survey of the literature and, most importantly, a review of real transactions in the open market, it is clear that valuators should not be constrained by the growing acceptance of modern mineral resource codes. On the contrary, valuation practitioners should be encouraged to examine all classes of mineralization and, after making due allowance for risk, to utilize all mineral resources as a basis for determining fair market value.

Jan 1, 2002

By R. A. Metz, Michael M. Easdon, Michael J. Fiannaca

Disseminated epithermal gold metallization occurs within a breccia unit interpreted to be a submarine debris flow. Gold is associated with oxidized pyrite, fluorite, and jasperoidal silica. A minimum of 8 Mt (9 million at) of open-pittable mining reserves will be cyanide heap leached as run-of-mine ore at a rate of 0.9 Mt (1.0 million stpy). Careful evaluation of the combined results of successive sampling projects has established the pit plan, minable reserves, and process metallurgy of the operation. The sampling procedure utilized for a given test depended upon geological interpretation as well as the procedures, successes, and failures of previous tests. This paper summarizes the sampling and testing procedures of the development effort in light of the project goals and attendant problems in achieving them.

Jan 1, 1992

By Gill G. Geesey, Michael R. Hankins, Paul L. Wichlacz, Anita Gianotto, John G. Jolley, Randy B. Wright

Thin films of copper [2.0 nm on germanium internal reflection elements (IREs) and 3.4 nm on germanium discs] were exposed to 10% gum arabic (aqueous solution) , 2% alginic acid (aqueous solution), 1% bacterial culture supernatant (BCS, simulated seawater solution) and 0.5% Pseudomonas atlantica exopolymer (simulated seawater solution). The IRES were monitored in situ, in real time using fourier transform infrared/cylindrical internal reflection/attenuated total reflection spectroscopy as a function of time at ambient conditions. The discs were characterized (pre- and post-exposure) by X-ray photoelectron and Auger electron spectroscopies. Ancillary graphite furnace atomic absorption spectroscopy was used to monitor the removal process of the copper thin film from the germanium substrates. Results indicate that Cu was oxidized by gum arabic, alginic acid and BCS. Furthermore, Cu was removed from the Cu/Ge interface by all four polymers. The Cu was found associated with the polymer solutions.

Jan 1, 1989

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

Aquifer. A formation, group of formations, or part of a formation that contains sufficient satu rated permeable material to yield significant quan tities of water to wells and springs. Artesian. Synonymous with confined; see ground water, confined. Capillary fringe. The zone immediately above the water table in which all or some of the interstices are filled with water that is under less than atmospheric pressure and that is continuous with the water below the water table. Conceptual model. A conceptualization of a field hydrogeologic framework that facilitates the development of analytical field testing procedures. The results of the test(s) may force changes in the initial conceptual model. Conductivity, hydraulic. Replaces the term "field coefficient of permeability." The volume of water at the existing kinematic viscosity that will move in unit time under a unit hydraulic gradient through a unit area measured at right angles to the direction of flow, if the porous medium is isotropic and the fluid homogeneous. Confining bed. A body of "impermeable" material stratigraphically adjacent to one or more aquifers; its hydraulic conductivity may range from nearly zero to some value distinctly lower than that of the aquifer. Flow, steady. Any point where the magnitude and direction of the specific discharge are constant in time. Flow, uniform. At every point the specific discharge has the same magnitude and direction. Flow, unsteady. At any point the magnitude or direction of the specific discharge changes with time. Fluid potential. The mechanical energy per unit mass of a fluid at any given point in space and time with respect to an arbitrary state and datum; the fluid potential is proportional to the head. Ground water, confined. Ground water under pressure significantly greater than atmospheric; its upper limit is the bottom of a bed of distinctly lower hydraulic conductivity than that of the material in which the confined water occurs. Ground water, perched. Unconfined ground water separated from an underlying body of ground water by an unsaturated zone. Ground water, unconfined. Water in an aquifer that has a water table. Head, static. Height above a standard datum of the surface of a column of water (or other liquid) that can be supported by the static pressure at a given point. Homogeneity. Hydrogeologic properties are identical everywhere. Hydraulic gradient. Change in static head per unit of distance in a given direction. Hydrostratigraphic unit. A body of material having considerable lateral extent and comprising a geologic framework for a reasonably distinct hydrogeologic system. Isotropy. Condition in which all significant properties are independent of direction. Porosity. Property of containing interstices or voids; may be expressed quantitatively as the ratio of the volume of its interstices to its total volume. Porosity, effective. Interconnected pore space available for fluid transmission; expressed as a percentage of the total volume occupied by the interconnecting interstices. Potentiometric surface. A surface that represents the static head along a particular specified surface or stratum. Specific retention. Ratio of the volume of water that the rock or soil, after being saturated, will retain against the pull of gravity to the volume of the rock or soil. Specific yield. Ratio of the volume of water that the rock or soil, after being saturated, will yield by gravity to the volume of the rock or soil. Storage, specific. The volume of water released from or taken into storage per unit volume of the porous medium per unit change in head.

Jan 1, 1986

By E. P. Chen

This investigation involves the development of a two-dimensional continuum model for the description of jointed media. Specific application of the model developed here is for the potential geological disposal of radioactive waste in the layered sequence of fractured volcanic tuffs under Yucca Mountain, Nevada. This is currently being considered by the Nevada Nuclear Waste Storage Investigations Project, administered by the Nevada Operations Office of the U. S. Department of Energy. The work is a direct extension of the previous constitutive model by Thomas (1982) based on the work of Morland (1974). The main feature of Thomas&apos;s model includes two parts: a continuum approximation based on average discontinuous displacements across jointing planes within a representative elementary volume, and a material constitutive description based on linear elastic matrix material behavior and nonlinear normal and shear joint behavior between jointing planes. The mathematical descriptions by Morland based on strain partitioning among matrix material and joint sets allow multiple joint sets to be included in the model. However, the initial effort by Thomas to implement Morland&apos;s mathematical model included only a single set of joints. To make the material model reflect more realistically the field characteristics, the current work extended Thomas&apos;s model to include orthogonal sets of joints. The nonlinear elastic normal joint behavior is retained in the present model. Joint shear response was treated as linear elastic in the shear stress versus shear displacement relationship prior to attaining the stress level governed by the Coulomb friction criterion. Beyond this critical stress value, a horizontal line is assumed in the work of Thomas for the shear stress versus slip displacement relationship such that the shear stress remains constant while the slip displacement increases. Motivated by experimental observation, the current work generalized the shear response to allow a line with finite slope to govern the slip behavior beyond the critical stress level. The inclusion of an orthogonal joint set led to a fourth order algebraic equation for the calculation of stress increments as compared with a second order equation obtained by Thomas. The nonlinear elastic normal joint behavior provides criteria which allow the selection of the root that yields result consistent with the loading condition of the problem. The addition of one more set of joints provides the potential to more completely study the interaction of various parameters representing the characteristics of jointed media behavior. Material responses to various loading conditions based on the present constitutive model have been obtained. These results and their comparisons to single joint set results are presented. Formulation of the Continuum Model The inclusion of an orthogonal joint set led to a fourth order algebraic equation for the calculation of stress increments as compared with a second order equation obtained by Thomas. The nonlinear elastic normal joint behavior provides criteria which allow the selection of the root that yields result consistent with the loading condition of the problem. The addition of one more set of joints provides the potential to more completely study the interaction of various parameters representing the characteristics of jointed media behavior. Material responses to various loading conditions based on the present constitutive model have been obtained. These results and their comparisons to single joint set results are presented. Let us focus our attention on the set with normal n first. Let the jump dilation displacement and jump slip dasplacement associated with the [ ]

Jan 1, 1986

By Gamal Rashed, Tim Miller, Nicole Evanek

High horizontal stress has been identified as a critical factor affecting roof stability in underground mines, particularly when the immediate roof consists of weak or laminated rock. Numerical models were employed to better understand the influence of caprock thickness, cutting sequences, and the orientation of driving direction relative to maximum horizontal stress on roof stability in underground stone mines. These models were calibrated based on field observations of roof falls from the study mine. The findings of this study enhance our understanding of roof stability under high horizontal stress and contribute to reducing the risk of roof falls in underground stone mines.

Feb 1, 2025

By B. Kolonja

This paper considers simulation of truck dispatching system designs using maximum expected production of the truck-shovel system as the measure of performance. Two methods are utilized, multiple comparisons with the best (MCB) and the combination of MCB and the variance reduction technique known as common random numbers (CRN). These two techniques are compared via simulation experiments. The results show that the combined procedure of MCB with CRN is the superior tool to reduce the total number of replications needed to ensure the specified probability of correct selection over the finite number of designing systems. In this case study, MCB with CRN reduces the variance by 29% and the number of required replications by 48%. Also, the MCB with CRN procedure narrowed the confidence interval by 18%.

Jan 1, 1994

By M. G. Ayat

I have been following the discussions on coal degradation started by the article "Degradation process in coal slurry pipe-lines," by M.G. Ayat and B.C. Scott. I agree with Mr. Dasher&apos;s comments in January that the title of the article was perhaps misleading as the information appeared to pertain more to processing the coal than to transportation. Specifically, the authors&apos; conclude that the cyclone had an important impact on the degradation. Dr. Ferri&apos;s comments on degradation in other physical processes was very correct, handling of coal in a turbulent manner has an impact on the size distribution of the coal. This is one reason that when I design a coal system (mine to rail car) I try to minimize the total number of transfer and processing steps consistent with achieving the desired product specifications. Another area, mentioned in passing in the article, the impact of natural causes and the mining step, is of particular interest to me. A mine in West Virginia had a variation of 50% in the -6.35 mm (-0.25 in.) raw coal depending upon the direction of mining. Since it was a single unit mine, this significantly impacted the final product. Two articles on mining&apos;s impact on size distribution are: • Stefanko, R., Chopra, I. K., and Ramani, R. V., 1974, "Mining influence on size consistency and washability char¬acteristics of coal," SME Fall Meeting. September; and • Albrecht, M., and Olsen, D., 1980, "Mining methods impact on coal preparation plant design." 1st International Mine Planning and Development Symposium. September. Both articles presented information on variation of size distribution and cleaning plant performance on a coal depending on the mining method used. Both articles considered a single coal seam at one mining operation. Stefanko&apos;s article considered continuous and conventional mining of coal in Pennsylvania. Albrecht&apos;s article considered surface, underground continuous, and underground hydraulic mining of a coal in British Columbia. Both concluded that mining methods do impact coal characteristics. I agree with Mr. Ayat&apos;s comments in reply to Dr. Ferri&apos;s discussion, "... degradation is a multi-faceted phenomenon involving many natural and man-made factors." As efforts are being made to produce a higher quality (lower sulfur) coal, this topic becomes even more important

Jan 1, 1990

By M. G. Ayat, J. Dasher

Having an interest in coal slurry pipelines from a decade of arguments with Ed Wasp and crew at Bechtel about pumping thicker slurries slower, I immediately read this article and found nothing in it pertinant to the title. Ayat and Scott pumped five unidentified coals at 9% solids (50%-60% is the area of interest) in a 25-mm (1-in.) pipe around two square elbows through a 76-mm (3-in.) cyclone for up to 60 minutes and sized a large number of samples of unstated size on an unidentified wet screening device. They did not measure power consumption, discharge pressure, flow rate, or give pump tip speed or impeller diameter. They siad the cyclone had a "high" pressure drop (unmeasured) and did much of the degradation (measured) but more or less per unit of energy expended? Hargrove was not measured, so there are no data as to whether it would correlate with degradation. The authors conclude, with no attempt, correlation is "hard to establish." Please experiment before concluding. I am at a loss to know what "increasingly smaller size" means, much less what theory says such particles take "exponentially larger quantities of energy," which the authors neglected to measure. If such experiments without pertinent data or justified conclusions must be published, please attach a pertinant title.

Jan 1, 1990

By J. Dasher

Regarding the March 1991 ME technical paper by De Souza and Moore: For more than a decade since my February 1981 article on how to use modern metric, which SME-AIME had decided to do, I have monthly pointed out metric errors to the editors. In part, I do this because there has been no action to al low editors to fix figures and tables or to allow them to require authors to do so. The latest resulting atrocity provokes this discussion of vibrating drill handle units being stated in decibels.

Jan 1, 1991

By Dean S. Rogers, R. A. Metz

The conventional role or exploration, development and grade control is examined in this paper within the context of the many and varied types of gold occurrences which are found at the Dome Mine. The account endeavours to trace the development of the total ore evaluation process, from diamond drilling through the exploration and drifting stage, to the stope development and planning phase of the operation, with an emphasis on sampling techniques and assaying procedure. The concept of ore reserve calculations is developed and the practice of grade control is described. In summary, the role of the geological, the engineering and the mining department is presented in relation to the contribution each has to make in the evaluation and exploitation of ore from one of the world&apos;s classic Archean gold deposits.

Jan 1, 1992