Search Documents

By Lauren M. Roberts, Ralph R. Sacrison

The Meikle Mine uses long-hole open stoping and cut-and-fill methods with backfill as the primary ground support technique. The mine operates at 2,858 tonnes per day (3,150 tpd) and has sustained operation in excess of 3,175 tonnes per day (3,500 tpd). Consistent backfill production is critical in achieving these mining rates. The heart of the system is a 7.65 cubic meter (10-cyd) horizontal shaft ribbon mixer located 328 m (1,075 ft) underground. System control is through several PLC's, allowing for a high degree of automation and process flexibility. Aggregate feed is routed 257 m (842 A) through vertical drop pipes in the ventilation shaft, a rockbox, transfer raises, and then into either of two raisebored storage silos. The aggregate is crushed mine waste, nominally 70% 3.8 cm x 1.0 cm (1-1/2"x 3/8") and 30% -1.0 cm (- 3/8"). The binder is routed through a vertical borehole, surge bins, and transfer raises. The binder is a mixture of Type II cement and fly ash. Two primary manufactured fill designs are produced: a high strength mix for stopes which will be undercut; and a low strength mix for stopes with only rib exposure. The high strength target is 5.5 Mpa (800psi) unconfined compressive strength in test cylinders. The low strength target is 2.8 Mpa (400 psi). The systim has allowed consistent achievement of these targets, while experience has allowed reduced costs and increased efficiencies. Fill placement is through 6.1 cubic meter (8 cyd) LHD's dumping into stopes. Specific sills and cut-and-fill drifts are jammed to the back. System enhancements have included colloidal mixers for cemented waste slurry placement and transfer raises for sending manufactured fill to the lower levels of the mine.

Jan 1, 2001

By C. A. Moseley, M. B. Kahle

The Gulf Coast Region has been the center of extensive lignite exploration and development activity in the past 10 years. Currently, 27.2 Mt (30 million st) of lignite are mined annually, the majority of which is uncovered by large walking draglines. Projections indicate that production could reach 125 Mt (138 million st) by 1990. As mining moves to deeper depths, removal of overburden becomes the decisive factor in mine planning and cost. The geology of a region plays a key role in the selection of an overburden removal system. While alternate stripping methods must be analyzed to determine the most economical and operationally sound method, so far bucketwheel excavator systems seem to be the best method for removing large volumes of soft, unconsolidated material that is found at projected mining depths in the Gulf Coast region. Geology of Gulf Coast Lignites Extent Distribution of the principal tertiary lignite-bearing deposits in the Gulf Coast Lignite province extend from the Texas-Mexico border to the Alabama-Georgia state line (Fig. 1). The lignite-bearing strata includes portions of eight states: Texas, Louisiana, Arkansas, Missouri, Kentucky, Tennessee, Mississippi, and Alabama. Lignites occur primarily in the Wilcox, Claiborne, and Jackson groups in the Gulf Coast. The uppermost strata of the Midway group in Mississippi and Alabama also contain significant lignite resources. Reserves Commercial lignite seams in the Gulf Coast Lignite province range from 0.6-3 m (2-10 ft) in thickness. The estimated lignite resources throughout the Gulf Coast in seams greater than 0.9 m (3 ft) in thickness and up to 61 m (200 ft) in depth currently are estimated at 32 Gt (35 billion st). Table 1 shows these resources by state. Quality Lignite quality can vary within individual mining areas and seams. However, trends in quality occur because of the depositional environment, age, and west-to-east geographical location. Better quality lignites occur in the Wilcox group in Texas and Louisiana. Poorer quality lignites occur in the northern regions of the Wilcox group and those of the geologically younger Claiborne and Jackson groups. Environmental Conditions Gulf Coast province environmental conditions are ideal for successful mine reclamation. The lignite occurs in flat to moderately rolling terrain, a topography easily reproduced from the spoil dumps or spoil rows developed during the mining operation. High to moderate rainfall facilitates rapid revegetation. Evidence from current mine reclamation programs and ongoing test plot studies indicate that mined lands can be reclaimed to reach premining productivities. Sometimes productivities are even greater than that of premining conditions. Existing Mining Methods Present Mines & Production There are seven active mines in the Gulf Coast province, all located in Texas (Fig. 2). Lignite

Jan 8, 1983

By Joao B. Cardoso

This paper describes a two-stage reverse flotation method developed at the Mineral Resources Institute (MRII, University of Alabama, for Kerr-McGee Corporation (KMC), to separate the trona (Na2CO3 ? NaHCO3 ? 2H2O) from a saline deposit containing halite, borax, minor salts, and water insoluble materials. In the first stage, trona is depressed with Quebracho, and the insoluble gangue is floated with fatty acid. In the second stage, trona is floated with cresylic acid. The flotation concentrates contained better than 90% trona with insolubles ranging between 1 and 2%. Although the trona recoveries were low, optimization and middlings recycled in a continuous circuit could substantially increase the value.

Jan 1, 1989

By Robert A. Robinson, Steven R. Thompson, Harvey W. Parker

The Mt. Baker Ridge Tunnel, under construction in Seattle, will be the world's largest-diameter soil tunnel with an inside diameter of 19.2 m (63 ft) and an effective outside diameter of about 24.4 m (80 ft). The five-lane highway tunnel will be constructed using a "stacked-drift" scheme in which an articulated or "flexible" tunnel lining consisting of 24 concrete-filled drifts is constructed to form a horizontal compression ring followed by removal of the soil core. Geotechnical factors, including variable strength hard fissured soils, high horizontal stresses, potentially unstable sands, and prior slope instabilities, significantly influenced the innovative design and construction approach.

Jan 1, 1983

By Bruce H. Van Brunt, Danny L. Taylor

Estimation of local recovered tonnage and its grade above a cutoff is of paramount importance during the exploration and development stages of any mineral deposit. The spatial dis- tribution of grades as well as the cumulative distribution must be defined. In this paper, Probability Kriging, an estimator based upon rank order statistics and the estimation of the distribution of point grades within a panel, is applied to the Manhattan gold deposit. Mapping the conditional probabilities that estimated panel grades exceed a cutoff is useful to the understanding of the distribution of mineralization in a structurally controlled gold deposit.

Jan 1, 1989

By L. G. Austin

The general manner in which the liberation function must change during size reduction is described. Data from float-sink (washability) analysis of a coal is used as an illustration, and a Locking Index is defined and calculated. Ash is not distributed equally with respect to sieve size but is concentrated more in the finest sizes. On the other hand, the ash is less locked with coal in the finer sizes than in the larger sizes. Further crushing showed decreased locking in intermediate sizes, but the material in the fine sizes (produced from breakage of highly locked larger sizes) was more locked than material of the same size in the feed. Future work is also discussed.

Jan 1, 1995

By T. N. Patra, Sanjeeva Latchireddi, B. K. Mishra, Sravan K. Prathy

The motion of grinding balls has been the subject of study since 191 9 when Davis published the first treatise on this subject. Subsequently came the notion that knowing mill power draft, using Bond equation or others, is sufficient to do an analysis of grinding. Next, population balance models provided accurate scale-up from small laboratory size mills to very large plant size mills. However, this success was not repeated when dealing with semiautogenous grinding mill. The study of charge motion with the discrete element method provides support and answers to such issues. Besides providing an accurate picture of charge motion in large mills, the method begs the investigator to study grate and pulp lifter equally critically with fluid dynamic principles. Hence, in recent years, the field of comminution in grinding mills is advancing on a firm footing.

Jan 1, 2005

By J. A. Herbst, Y. C. Lo

An attempt has been made to parameterize the population balance model for a ball mill based on measurements of the elementary breakage process obtained using an ultrafast load cell device. Detailed insight obtained concerning the fragmentation of particle assemblies with the ultrafast load cell leads to a better understanding of ball mill grinding. The ball mill breakage function and specific selection function are derived from an average single event representing the multiple breakage events which occur in ball mill grinding. Since both the breakage function and the specific selection function depend on the loading mode in the mill, predictions of breakage mechanisms in ball mills are possible by using data obtained in various elementary loading modes. The application of this model to the description of batch ball milling behavior has resulted in reasonably accurate predictions of product size distributions for various energy inputs.

Jan 1, 1992

By P. K. Davis, B. Gharib

The results of a previous basic study of the flow and design characteristics of hydrocyclones demonstrated that a recovery as high as 99% with a product rating* of 0.95 can be achieved on a batch+ basis with a single, water-only cyclone if it is configured properly. The next logical step was to demonstrate continuous processing of gob for the efficient recovery of coal by means of a laboratory-size demonstration system. A project to design and construct such a single-¬cyclone system was sponsored by the US Department of Energy, which also sponsored the initial study. A recovery of 93% with a product rating of 0.89 was demonstrated. The system design and the data taken are discussed.

Jan 1, 1990

By D. Marinakis

Gas hydrates (GH) are crystalline compounds consisting of a water molecule lattice, in the cages of which suitably sized molecules, such as methane or other light hydrocarbons, are confined. Although this solid phase looks similar to common ice, it contains substantial amounts of natural gas. The necessary conditions for natural gas hydrate formation exist in some deep-sea marine environments and in permafrost regions. Despite the extensive research, which has been conducted in the fields of exploration and exploitation of natural gas hydrate deposits over the last decades, there is still great uncertainty over the estimated amount of hydrates that these reserves bear. The present work examines some key features of sediments which affect their capacity to host gas hydrates. The hydrate content of a natural hydrate formation is correlated qualitatively with factors such as temperature, effective porosity, mineralogical composition, bio-surfactants, pore pressure and compaction pressure.

Jan 1, 2006

By G. T. Adel, W. Z. Choi

A model describing size reduction and mineral liberation during grinding has been extended to include multiple classes of composite particles. The majority of the model parameters have been directly determined using computerized image processing equipment to analyze the products from batch grinding tests. A coarse-grained sphalerite ore from Tennessee, representing a nearly ideal binary mixture of sphulerite and dolomite, has been used to experimentally validate the model for the case of dry batch grinding. In all cases, excellent agreement has been observed between the model predictions and the experimental results.

Jan 1, 1988

By N. I. Fedunets

The development of variousworks on automatising of operational processes at coal¬extractive and coal-mining enterprises introduces an ever growing necessity to carry out investigations in the wide range of problems concerning the possibitity of joint functioning of different levels, which seems impossible without the use of integrated systems of passing on and prossessing the information on the basis of modern calculating machines and other means of automation. This view on the problem of automation of the enterprise operation presupposes that the structure of automated operational dispatcher control (AODC) should be very closely connected with that of integrated data processing system! In this case the AODC structure from the point of view of automation of its functions (or operations), i.e. from the point of view of informational techniques coinsides in general with the structure of dispersed information and calculating network (ICN), realizing the passing on and processing of the information as well as solving the functional tasks on the basis of local calculating networks of electrical calculating machines with correspond to different levels of AODC and located with regard to productional hierarchy of operational dispatcher control (ODC). In this approach however the use of dispersed, ICN gives opportunity to. realize the possibility of action only with realisation on the CM of algorithmic' task of ODC, when a dispatcher 'is the lastto make a final decision.. At the mining enterprises it's rather difficult for a dispatcher to make a final decision because of the great variaty of productional situations, the presence of contradictions and a number of other subjective factors which often lead to the dispatcher's mistaks causing great material losses of the enterprise. Hence the necessity arises to automize and formalize making a decision and including the expert systems (ES) into the ontour of AODC, which enables the dispatcher 2to get a neeessary advice in different situations, especially in case ofemergency on the basis of establishing the mechanism of logical layout of non-formalized data base (DB) procedures relying upon the background knowledge and experience of experts. The presently presented in this paper theory of establishing the. ISAODC on the basis of dispersed ICN and expert systems is aimed at trasformation ofoperational' tasks of the higher level into the technological ones, at solving the tasks of diagnostics and forseeing of the process of production, with a dispatcher getting an opportunity of making qualitative and effective decision concerrning the choice of operational impacts in actual time on the basis of generalization the realisation of presented conception must, as has been already mentioned, be accomplished only on the basis of the foundatoin of the united dispersed informational - calculating network of electrical calculating machines.. This includes ICN which would be operating in . different operational contours. . From what has just been said it followsthat the ISAODC Structure will conside with that of DICN (in our case) and hence all the problems of ISAODC structure would be regarded as the questions of DICN.

Jan 1, 1992

By T. E. Garnar

Heavy mineral mining has been a small, but important Florida industry over the past sixty years. Early geologic history of each deposit is similar up to point of deposition in alluvium, deltaic sediments, or along shorelines. Later geological development through reworking and concentration is different for each deposit. The Trail Ridge deposit was formed by reworking Citronelle sediments of the Lake Wales ridge. Post depositional leaching of iron from ilmenite makes Trail Ridge an important source of titanium minerals for TiO2 pigment manufacture. Research leading to the separation and sale of by-product heavy minerals from Florida deposits has been important in maximizing profitability. Advances in mineral dressing technology will lead to future mining of lower grade reserves. Future needs for heavy minerals seem certain to expand, with increased activity in exploration and development of mining operations.

Jan 1, 1972

By A. B. Cecala

The US Bureau of Mines performed a study to determine optimal locations for longwall face methane monitoring equipment. Longwall face ignitions continue to be a concern to the US coal mining industry. Gains in ignition control technology have been somewhat negated by advances in longwall productivity. More reliable, heavy duty longwall face systems generate higher production rates and increase methane liberation rates. These rates will likely continue to rise as further coal production increases occur. Efforts will continue in the areas of methane drainage, methane containment and methane dilution. In addition, more effective face methane monitoring is needed. As technology continues toward automated longwall panels, the importance of monitoring for methane at the shearer becomes even more significant. Since the primary face ignition source is the shearer mining machine, the Bureau ran tests to determine the best location to take methane readings on the shearer. This information, in conjunction with data obtained from field studies, provides a knowledge base for selecting optimum face methane monitoring locations.

Jan 1, 1995

By Terry Mudder

Long-term anaerobic biochemical treatment for draindown of residual solutions is a cost-effective way to close a heap-leach pad. This article presents a laboratory evaluation of anaerobic biochemical treatment of cyanide heap-leach pad solutions. The traditional approach to heap-leach pad closure is to rinse the pads with multiple pore volumes of fresh or recycled treated water. The effluent from an initial rinse is often treated and recirculated until the solutions passed through the heap meet the appropriate numeric and narrative water quality standards. Column rinsing tests are completed during project planning to determine the number of pore volumes of fresh or recycled treated water required to rinse the pad to meet long-term closure requirements. A traditional closure plan generally includes provisions to sample the rinse effluent and rinsed solids (the Meteoric Water Mobility, Procedure or USEPA 1312) to verify that chemical requirements are being met.

Jan 1, 1995

By Wayne Stange

Due to the availability of user-friendly microcomputer based packages, the use of simulation is increasing.. Users have however encountered problems inherent to the structure of sequential-modular simulators. These are the difficulties associated with estimating parameters for arbitrary' models and the solution of design and optimization problems. The implementation of an optimization routine in the simulator MicroSim has facilitated the solution of such problems. The literature indicates that more efficient numerical techniques for solving optimization problems than those presently used in MicroSim are available. These techniques, together with user-interfaces which allow such problems to be specified easily by users, will result in the development of simulators much more powerful than existing ones.

Jan 1, 1989

By H. E. Bonner

The recovery of fine coal has historically had limited success due to the intimate clay association on the surfaces of the coal particles. This clay presence has detrimentally affected conventional beneficiation techniques resulting in a recovered product containing unacceptably high concentrations of ash and moisture. An ultrasonically activated tray that operates in a continuous fashion has been developed that separates the clay film from each particle's surfaces. This separation is of sufficient duration to allow conventional beneficiation techniques to be utilized more efficiently.

Jan 1, 1989

By Preusse. Axel

Underground coal mining can cause seismic events. There is currently no way to predict such phenomena reliably, in particular stronger events. That is why, according to the current state of the art, empirical methods are employed in this field. Some assessment criteria, which relate to the geological and mining situation and either stimulate or rather help to avoid seismic events, are presented in this paper. These criteria are examined for a practical mining situation in Germany, with a view to estimate possible seismic events.

Jan 1, 2009

By Pradip

Chelatang agents, because of their metal specificity, can function as effective mineral processing reagents. A brief review of the work carried out in this area is presented. Some of the salient features of mineral flotation and flocculation with chehting-type reagents, such as bulk us. surface chelation, the role of pH, mineral solubility, solution chemistry of reagents, and temperature, are illustrated with appropriate examples. The problems associated with the commercialization of chelating reagents for ore beneficiation and the research efforts required in this area are also discussed.

Jan 1, 1987

By R. Q. Honaker, D. P. Patil, A. Sirkeci

Because of increasing production of fine coal during mining over the past century and because of inefficient fine-coal recovery technologies, a vast reserve of high-quality coal now exists in refuse ponds. A novel finecoal circuit, consisting of a hindered-bed classifier, an enhanced gravity concentrator and a flotation column, was evaluated for the recovery of fine coal from refuse ponds. The treatment of a pond derived from Pittsburgh No. 8 seam coal resulted in the production of a premium fuel containing less than 5% ash and a calorific value of about 30,170 kJ/kg with 60% mass yield. Results from the treatment of two refuse pond materials are presented in this paper.

Jan 1, 2002